High Pressure Temperature Research Articles

Synergistic optimization on Seebeck coefficient and electrical conductivity in 2H-MoS2 enabled by progressively evolved stacking faults under high pressure and high temperature

In thermoelectricity, the stacking faults (SFs) have been investigated mainly in phonon transport but rarely in carrier transport. For the layered thermoelectric materials, the layered nature makes them prone to SFs, especially under high pressure because of the induced shear stress between grains. Herein, we take the typical layered 2H-MoS2 as an example to investigate the effect of high-pressure in situ-induced SFs on the thermoelectric transport properties under high pressure and high temperature. It was found that a continuous transition of P-N-P type conductive behavior with increasing pressure was observed in the sign of Seebeck coefficient, finally leading to a not weakened Seebeck coefficient. Furthermore, the in situ-induced SFs enhanced the interlayer interaction and provided transport channels for carriers across the interlayers to boost the electrical conductivity to ∼11 100 S m−1 at 5.5 GPa, 1110 K. Consequently, combined with intrinsic ultralow thermal conductivity of MoS2, a maximum ZT value of 0.191 was obtained at 5.5 GPa, 1110 K, comparable to those doped/composited MoS2. This conduction-type transition induced synergistic optimization on Seebeck coefficient and electrical conductivity could be ascribed to that SFs, which had a progressive evolution process for stabilization with rising pressure, in which some associated defects might be induced, and the band structure could be modified for regulating the carrier distributions and the density of states around the Fermi level. This study provided profound insights of regulating conduction type via dynamically modulating the lattice defects for designing a high-efficiency TE device.

Investigation into Enhancing Methane Recovery and Sequestration Mechanism in Deep Coal Seams by CO2 Injection

Injecting CO2 into coal seams to enhance coal bed methane (ECBM) recovery has been identified as a viable method for increasing methane extraction. This process also has significant potential for sequestering large volumes of CO2, thereby reducing the concentration of greenhouse gases in the atmosphere. However, for deep coal seams where formation pressure is relatively high, there is limited research on CO2 injection into systems with higher methane adsorption equilibrium pressure. Existing studies, mostly confined to the low-pressure stage, fail to effectively reveal the impact of factors such as temperature, high-pressure CO2 injection, and coal types on enhancing the recovery and sequestration of CO2-displaced methane. Thus, this study aims to investigate the influence of temperature, pressure, and coal types on ECBM recovery and CO2 sequestration in deep coal seams. A series of CO2 core flooding tests were conducted on various coal cores, with CO2 injection pressures ranging from 8 to 18 MPa. The CO2 and methane adsorption rates, as well as methane displacement efficiency, were calculated and recorded to facilitate result interpretation. Based on the results of these physical experiments, numerical simulation was conducted to study multi-component competitive adsorption, desorption, and seepage flow under high temperature and high pressure in a deep coal seam’s horizontal well. Finally, the optimization of the total injection amount (0.7 PV) and injection pressure (approximately 15.0 MPa) was carried out for the plan of CO2 displacement of methane in a single well in the later stage.

Synthesis of Homoallylamine Covalent Organic Frameworks Via Hosomi-Sakurai Reaction Under Mild Conditions.

One-pot multicomponent reactions (MCRs) are a valuable strategy to synthesize functional covalent organic frameworks (COFs) in a single step. Most reported COF syntheses involve solvothermal processes, and because of the harsh reaction conditions, such as high temperature or high pressure, large-scale production of COFs has been limited. The synthesis of homoallylamine substituted COFs via a one-pot Hosomi-Sakurai reaction is reported. At room temperature the reaction of allyltriethylgermane with either terephthalaldehyde or [1,1'-biphenyl]-4,4'-dicarbaldehyde, and 1,3,5-tris(4-aminophenyl)benzene (TAPB) is catalyzed by Sc(OTf)3 to produce two COFs: TAPB-1P-Allyl COF and TAPB-BP-Allyl COF. The allyl functionalized COFs shows high crystallinity, with micropores ranging from 3.2 to 3.9nm, for TAPB-1P-Allyl COF and TAPB-BP-Allyl COF respectively, and both COFs are hydrolytically stable at different pH levels. Post-synthetic modification of these COFs with iodomethane produces methylated cationic COFs that demonstrates >98% adsorption efficiencies below the detection limit of perfluorooctanoic acid (PFOA) and perfluorodecanoic acid (PFDA) from aqueous solutions. After four cycles adsorption efficiency remains high with concentrations of PFOA below the detection limit.

Designing invert emulsion drilling fluids for high temperature and high-pressure conditions

Good and optimal rheology is a primary requisite for a drilling fluid to achieve better hole-cleaning and barite sag resistance. Conventional thickeners like organophilic clay that provide rheology to invert emulsion fluids degrade with time and thereby fail to maintain sufficient rheology of the drilling fluid. Generally, excess amount of organophilic clay or low gravity solids (LGS) is added to the drilling fluid to enhance rheology. However, addition of excess amount of organoclay or low gravity solids not only increases the cost of drilling but also may severely affect other drilling fluid properties, which will require further treatment. In addition, addition of organoclay or low gravity solids increases the plastic viscosity, decreases the rate of penetration thereby ultimately increasing the cost of drilling. Thus, there was a need to develop a drilling fluid with optimal rheology sufficient to give good hole cleaning and barite sag resistance. This paper describes the formulation of 70pcf, 90pcf and 120pcf organoclay-free invert emulsion drilling fluids formulated with a novel rheology modifier combination of RM1 and RM2. The paper describes the synergistic effect of RM1 and RM2 which is a combination of fatty acid and fatty amine respectively. The fluids were hot rolled at 250°F, 250°F and 350°F respectively and the temperature effect on the rheological and filtration properties were studied. The paper also describes the static aging and contamination studies of 90pcf and 120pcf fluids at 250°F and 350°F respectively. Rheology of the 90pcf invert emulsion fluid was measured across high temperature and high pressure (HTHP) conditions to observe their effects on the fluid properties. 70pcf, 90pcf and 120pcf organoclay-free invert emulsion drilling fluids formulated with the novel rheology modifier combination of RM1 and RM2 showed optimal rheology and low HTHP fluid loss. Static aging studies of 90pcf IEFs at 250°F respectively showed that the fluids are sag-resistant with low top-oil separation. Contamination studies of 90pcf fluid showed that the contaminants have minimal effect on the rheology and filtration properties of the invert emulsion fluid. HTHP rheology of the 90pcf invert emulsion fluid shows consistent rheology across high temperatures and pressures. The paper thus demonstrates the superior performance of the rheology modifier combination to achieve good rheological and filtration properties.

Plasma-Assisted Synthesis of Methanol Through Hydrogenation of Carbon Dioxide With Non-Noble Metal Mixed Oxide Catalysts.

The utilization of carbon dioxide through chemical conversion is a promising approach for the recycling of carbon resources. Despite well-developed industrial processes for CO2 hydrogenation to methanol, the effective use of CO2 as a feedstock remains challenging because of the costly requirements of high temperature and reaction pressure. In this paper, we report the methanol synthesis from CO2 and hydrogen using a dielectric barrier discharge (DBD) reactor under atmospheric pressure with a nickel-cerium-aluminum mixed oxide (Ni/Ce-Al MOx) catalyst. The combined use of plasma and the Ni/Ce-Al MOx catalyst was observed to yield 13.3±0.4 % of methanol, favorably compared to the 2.6±0.5 % yield of the case without catalyst. Microscopy images, selected area electron diffraction patterns, and energy-dispersive X-ray analysis confirmed the presence of fluorite-structured ceria, aluminium, nickel, and nickel oxide particles in the catalyst. The reaction mechanism for the plasma-assisted hydrogenation of CO2 was hypothesized to involve a carbide formation pathway due to the presence of carbide confirmed by X-ray photoelectron spectroscopic characterization.

Effect of temperature on transport index of fish oil-based drilling mud in high pressure high temperature well: a hybrid model approach

Diesel Oil-based drilling mud used in the oil and gas industry causes severe environmental and public health issues due to its high toxicity, especially in high-pressure, high-temperature (HPHT) wells. Therefore, easily biodegradable synthetic oil-based mud with high drilling performance is essential. Fish oil is a bio-oil known for its non-toxicity, high lubricity, thermal stability, and biodegradability. Effective hole cleaning is crucial for drilling performance and is ensured by the rheological properties of drilling mud. While rheological parameter prediction can be performed using an artificial neural network (ANN) based model, such models often fail to provide accurate predictions for unseen data. In contrast, empirical models are more robust and facilitate generalization. This study aims at assessment of the suitability of invert emulsion fish oil-based drilling mud (IEFOBDM) in HPHT wells through evaluation of hole cleaning performance (HCP) using a hybrid approach that combines an ANN with nonlinear regression (NLR) for temperatures ranging from 40 °C to 80 °C.Firstly, an ANN model was developed considering mud weight, temperature, and shear rate. Secondly, the NLR model was used in the prediction of rheological parameters, namely, Yield point (YP) and Plastic viscosity (PV), based on the predicted shear stress from the ANN model. Finally, the performance metrics of the ANN-NLR rheological model were evaluated using the root mean square error (RMSE) and correlation coefficient (R2) and comparison made with the Single ANN rheological model. The results showed the outperformance of ANN-NLR model over the ANN model for rheological parameter prediction, with R2 values of (0.99) for YP and (1) for PV. The predicted PV and YP values were then used for evaluation of transport index (TI) for HCP analysis. The effect of temperature on TI analysis showed this with increase in temperature, TI also increased, indicating the proposed mud providing good HCP under HPHT conditions.

Dynamic Nuclear Polarization with P1 Centers in Diamond.

Substitutional nitrogen impurities within the diamond lattice, known as P1 centers, have unpaired electrons that can mediate microwave driven dynamic nuclear polarization (DNP). In this paper we explore DNP of the bulk 13C spins in micrometer-sized P1 diamond particles and demonstrate a 550-fold DNP enhancement of the bulk 13C spins at room temperature in a 9 T magnetic field or 250 GHz for g ≈ 2 electrons. We study the DNP mechanisms, exploring their dependence on sample spinning frequency and microwave irradiation frequency using both continuous wave and frequency swept microwave irradiation, and discuss the results alongside recent DNP studies in the literature. Even with a modest microwave irradiation power of 160 mW from our frequency swept solid-state microwave source, we achieve a significant 13C signal enhancement, ε = 270 at room temperature. The enhancements were found to increase with the magic angle spinning (MAS) frequency, ωr/2π, and the results provide mechanistic insights into how different electron populations contribute to the observed DNP efficiency. These findings are inherently interesting and of practical importance in view of the recently reported diamond rotors fabricated from P1 high-pressure, high-temperature (HPHT) diamond.

High-Pressure Monosulfide Solid Solution FexNi1−xS Phases: X-Ray Diffraction Analysis and Raman Spectroscopy

High-pressure high-temperature (HPHT) crystalline monosulfide solid solution (Mss) phases (FexNi1−xS, x = 0.90, 0.75, 0.50, 0.25), troilite (FeS I), and α-NiS of the Fe-Ni-S system were synthesized at 7 GPa and 900–1550 °C. The structural parameters of the obtained phases were refined by XRD using the Rietveld method. Factor group analysis revealed the number of active Raman modes for FeS I and α-NiS. Raman spectra of troilite, α-NiS, and Mss phases were obtained. It was shown that the Raman spectra of Mss phases and α-NiS have a similar topology. The Raman spectra of the experimental phases in the Fe-Ni-S system were analyzed with non-negative matrix factorization, which provided a meaningful concentration dependence of the spectral patterns. The spectral components were assigned to the FeS I and α-NiS structures. The structural and spectroscopic studies show linear dependencies of unit cell parameters and spectral components on composition and confirm the existence of a series of monosulfide solid solution FexNi1−xS.

Intensifying Cyclopentanone Synthesis from Furfural Using Supported Copper Catalysts.

This work addresses catalytic strategies to intensify the synthesis of cyclopentanone, a bio-based platform chemical and a potential SAF precursor, via Cu-catalyzed furfural hydrogenation in aqueous media. When performed in a single step, using either uniform or staged catalytic bed configuration, high temperature and hydrogen pressures (180 °C and 38 bar) are necessary for maximum CPO yields (37 and 49 %, respectively). Parallel furanic ring hydrogenation of furfural and polymerisation of intermediates, namely furfuryl alcohol (FFA), limit CPO yields. Employing a two step configuration with optimal catalyst bed can curb this limitation. First, the furanic ring hydrogenation can be suppressed by using milder conditions (i. e., 150 °C and 7 bar, and 14 seconds of residence time). Second, FFA hydrogenation using tandem catalysis, i. e., a mix of β-zeolite and Cu/ZrO2, at 180 °C, 38 bar and 0.6, allows sufficient time for CPO formation and minimises polymerisation of FFA, thereby resulting in 60 % CPO yield. Therefore, this work recommends a split strategy to produce CPO from furfural. Such modularity may aid in addressing flexible market needs.

Innovative machine learning for drilling fluid density prediction: a novel central force search-adaptive XGBoost in HPHT environments

Oil and gas industries are facing a special dilemma when it comes to high-pressure, high-temperature (HPHT) drilling as the accurate forecasting of the drilling fluid density (DFD) is a vital factor for safe and efficient operations. Complicated relationships and inconsistencies in HPHT situations are rarely mapped by current forecasting models, while their buggy performance and safety risks during drilling can be underestimated. In this research, we propose a novel machine learning (ML) approach to enhance the accuracy of DFD anticipation under HPHT conditions: central force search-adaptive extreme gradient boosting (CFS-XGB). This paper uses a dataset that has drilling variables together with the DFD for HPHT situations to examine the accuracy of the CFS-XGB model. Excluding the abnormalities of data or mistakes, the reliability of the original data is maintained by applying min–max normalization. After that, finding the important features with the help of the boosted principal component analysis (BPCA) approach to the normalized data will ensure a major improvement in the CFS-XGB methodology’s prediction efficacy. This research is experimented in the Python platform, and the performance of the proposed CFS-XGB method is analyzed in terms of MSE, R2, and AAPRE metrics. The suggested approach performs better than the current methods in forecasting the drilling fluid concentration in HPHT settings, according to the experimental data. This development in predictive modeling helps increase the productivity and safety of drilling operations, which will eventually help the oil and gas sector manage the challenges posed by HPHT drilling settings.

Experimental Study on Cryogenic Compressed Hydrogen Jet Flames

Cryogenic compressed hydrogen (CcH2) technology combines the advantages of high pressure and low temperature to achieve high hydrogen storage density without liquefying the hydrogen, which has broad application prospects. However, the safety concerns related to cryogenic hydrogen need to be carefully addressed beforehand. In the present work, cryogenic hydrogen jet flames are experimentally investigated for various release pressures and initial temperatures. The flame length and thermal radiation flux were measured for horizontally releasing with nozzle diameters of 0.5–2 mm, temperatures ranging from 93 to 298 K, and initial pressures of 2–10 MPa. The results show that the flame length is dependent on the nozzle diameter, stagnation pressure and temperature. At a given pressure, the flame length, size and total radiant power increase with decreasing temperature, which is attributed to the lower jet flow velocity and higher density of low-temperature hydrogen. The normalized flame length Lf/D is correlated with the pressure ratio and temperature ratio. The correlation can be used to predict the flame length at various hydrogen pressures and temperatures. The normalized flame length of the cryogenic hydrogen jet flame is greater than that of the room-temperature hydrogen jet flame. The radiative heat flux of the flame can be predicted by the mass flow rate of the jet flow.

Vitamin C Alleviates Heat-Stress-Induced Damages in Pig Thoracic Vertebral Chondrocytes via the Ubiquitin-Mediated Proteolysis Pathway.

Heat stress can impair organismal growth by inducing ubiquitination, proteasome-mediated degradation, and subsequent cellular damage. Vitamin C (VC) has been shown to potentially mitigate the detrimental effects of abiotic stresses on cells. Nevertheless, the impact of heat stress on growth plate chondrocytes remains unclear, and the underlying protective mechanisms of VC in these cells warrant further investigation. In this study, we focused on pig thoracic vertebral chondrocytes (PTVCs) that are crucial for promoting the body's longitudinal elongation and treated them with 41 °C heat stress for 24 h, under varying concentrations of VC. Our findings reveal that, while oxidative stress induced by heat triggers apoptosis and inhibits the ubiquitin-mediated proteolysis pathway, the addition of VC alleviates heat-stress-induced oxidative stress and apoptosis, mitigates cell cycle arrest, and promotes cellular viability. Furthermore, we demonstrate that VC enhances the ubiquitin-proteasome proteolysis pathway by promoting the expression of ubiquitin protein ligase E3A, which thereby stabilizes the ubiquitin-mediated degradation machinery, alleviates the apoptosis, and enhances cell proliferation. Our results suggest the involvement of the ubiquitin-mediated proteolysis pathway in the effects of VC on PTVCs under heat stress, and offer a potential strategy to make use of VC to ensure the skeletal growth of animals under high temperature pressures in summer or in tropical regions.

Unraveling the corrosion behavior and corrosion scale evolution of N80 steel in high-temperature CO2 environment: The role of flow regimes

During CO2 transportation and storage, metal equipment such as oilfield pipelines suffers from severe CO2 corrosion, especially in harsh downhole injection equipment. In this study, we investigated the corrosion behavior of oil well tubing in a high-temperature, high-pressure (HTHP) CO2-containing environment. The evolution of the corrosion scale was also examined under different flow regimes. The results reveal a lower corrosion rate at 150 °C compared to 80 °C under different flow regimes, with localized corrosion intensifying as temperature and rotational speeds (vrs) increase. The temperature also induces the corrosion scale conversion of aragonite-type CaCO3 (80 °C) to calcite-type CaCO3 (150 °C). Specifically, the variation of the corrosion rate and the corrosion scale evolution can be attributed to the vortices within the reactor. The intact vortex cells enhance mass transfer while also promoting nucleation and growth of CaCO3. However, when vrs exceeds the critical Reynolds number, the vortex cells are disrupted, resulting in viscous dissipation and a reduced corrosion rate.

Development of two-layer whisker-reinforced PcBN materials for cutting tool applications

This study investigates the polycrystalline cubic boron nitride (PcBN) tool materials with a TiN-Zr based binder without additives (BTZ base material) and with whisker additives (SiCw, Al2O3w, Mg2B2O5w) obtained via high-pressure high-temperature (HPHT) sintering at 7.7 GPa and 2000 °C. The whiskers reinforced composite compacts were produced both in one- and two-layer (sandwich-type) forms. The phase composition, microstructure, physical-mechanical properties and cutting performance of the composite compacts were analysed. The results demonstrate that reinforcing with SiCw leads to the formation of BTZ+SiCw composites with a homogeneous microstructure, high hardness, and Young's modulus, enabling the manufacture of one-layer cutting inserts with an extended tool life of up to 11 min when turning Inconel 718 alloy. Similarly, the BTZ+Al2O3w one-layer material, despite exhibiting slightly lower hardness compared to BTZ+SiCw, still displayed satisfactory wear resistance with a tool life of up to 7 min. Notably, the two-layer (sandwich type) s1: BTZ+SiCw/BTZ+Al2O3w composite cutting inserts exhibited the highest durability, with a tool life of up to 13 min when tested on the SiCw-reinforced side and 8 min on the Al2O3w-reinforced side. In contrast, the BTZ+Mg2B2O5w composite was found unsuitable as a working tool component but shows promise as a substrate layer in two-layer configurations. The study indicates the potential for further development of whisker-reinforced two-layer composite PcBN materials to enhance tool performance and longevity.

Effects of supercritical CO2, water, and supercritical CO2-based water on the mechanical properties and fracturability of shale

The study of the effects of supercritical CO2 (ScCO2) under high temperature and high pressure on the mechanical properties and fracturing potential of shale holds significant implications for advancing our understanding of enhanced shale gas extraction and reservoir exploration and development. This study examines the influence of three fluids, i.e. ScCO2, deionized water (DW), and ScCO2+DW, on the mechanical properties and fracturability of shale at immersion pressures of 15 MPa and 45 MPa, with a constant temperature of 100 °C. The key findings are as follows: (1) Uniaxial compressive strength (UCS) of shale decreased by 10.72%, 11.95%, and 23.67% at 15 MPa, and by 42.40%, 46.84%, and 51.65% at 45 MPa after immersion in ScCO2, DW, and ScCO2+DW, respectively, with the most pronounced effect observed in ScCO2+DW; (2) Microstructural analysis revealed that while ScCO2 and DW do not significantly alter the microstructure, immersion in ScCO2+DW results in a more complex surface morphology; (3) Acoustic emission (AE) analysis indicates a reduction in stress for crack damage, with a decreased fractal dimension of AE signals in different fluids. AE energy is primarily generated during the unstable crack propagation stage; (4) A quantitative method employing a multi-factor approach combined with the brittleness index (BI) effectively characterizes shale fracturability. Evaluation results show that ScCO2+DW has a more significant effect on shale fracturability, with fracturability indices of 0.833% and 1.180% following soaking at 15 MPa and 45 MPa, respectively. Higher immersion pressure correlates positively with increased shale fracturability.

Electrical Conductivity and Sound Velocities of Talc Under High Pressure and High Temperature Conditions and Application to the Subducting Cocos Plate

AbstractTalc is expected to be an important water carrier in Earth's upper mantle, and understanding its electrical and seismic properties under high pressure and temperature conditions is required to detect possible talc‐rich regions in subduction zones imaged using geophysical observations. We conducted acoustic and electrical experiments on natural talc aggregates at relevant pressure‐temperature conditions. Compressional wave velocity (Vp) was measured using ultrasonic interferometry in a Paris‐Edinburgh press at pressures up to 3.4 GPa and temperatures up to 873 K. Similar Vp values are obtained regardless of the initial crystallographic preferred orientation of the samples, which can be explained by talc grain reorientation during the experiment, with the (001) plane becoming perpendicular to the uniaxial compression axis. Electrical conductivity of the same starting material was determined using impedance spectroscopy in a multi‐anvil press up to 6 GPa and 1263 K. Two conductivity jumps are observed, at ∼860–1025 K and ∼940–1080 K, depending on pressure, and interpreted as talc dehydroxylation and decomposition, respectively. Electrical anisotropy is observed at low temperature and decreases with increasing pressure (∼10 at 1.5 GPa and ∼2 at 3.5 GPa). Comparison of acoustic and electrical results with geophysical observations in central Mexico supports the presence of a talc‐bearing layer atop the subducted Cocos plate.

Cryogenic fracturing efficacy in granite rocks: Fracture toughness and brazilian test differences after elevated temperatures and liquid nitrogen exposure

Hot dry rock (HDR) is a significant contingent as a thermal energy source. Due to its low permeability, considerable depth, high temperature (150–650 °C), and high pressure, the stimulation of HDR is challenging. This research work aims to examine the efficacy of cryogenic fracturing on HDR. We performed fracture toughness and indirect tensile stress (Brazilian tests) on granite specimens with three different initial temperatures before exposure to liquid nitrogen (LN2). Fracture toughness tests were implemented on semicircular bend (SCB) specimens containing a pure mode-I fracture, and Brazilian tests were performed with discs. The experimental outcomes show that, overall, both critical load in Brazilian tests and the fracture toughness of LN2-treated specimens of granites both diminished with increasing initial temperature. When the initial temperature exceeded 300 °C (in this instance, 500 °C), the amplitude of thermally induced fractures in granite moderately increased after LN2 treatment, secondary fractures prolonged, and the plastic characteristics increased. Moreover, permeability measurements indicated amelioration with elevated temperatures and subsequent LN2 exposure. SEM analysis showed that an increase in initial temperatures along with LN2 treatment led to further intensified granite microdamage while the quantity and the magnitude of thermal fractures augmented.

Phase Behavior and Rational Development Mode of a Fractured Gas Condensate Reservoir with High Pressure and Temperature: A Case Study of the Bozi 3 Block

The Bozi 3 reservoir is an ultra-deep condensate reservoir (−7800 m) with a high temperature (138.24 °C) and high pressure (104.78 MPa), leading to complex phase behaviors. Few PVT studies could be referred in the literature to meet such high temperature and pressure conditions. Furthermore, it is questionable regarding the applicability of existing condensate production techniques to such a high temperature and pressure reservoir. This study first characterized the phase behavior via PVT experiments and EOS tuning. The operating conditions were then optimized through reservoir numerical simulation. Results showed that: (1) the critical condensate temperature and pressure of Bozi 3 condensate gas were 326.24 °C and 43.83 MPa, respectively; (2) four gases (methane, recycled dry gas, carbon dioxide, and nitrogen) were analyzed, and methane was identified as the optimal injection gas; (3) gas injection started when the production began to fall and achieved higher recovery than gas injection started when the pressure fell below the dew-point pressure; (4) simultaneous injection of methane at both the upper and lower parts of the reservoir can effectively produce condensate oil over the entire block. This scheme achieved 8690.43 m3 more oil production and 2.75% higher recovery factor in comparison with depletion production.

Comparative study of lysine acetylation in Vesicomyidae clam Archivesica marissinica and the manila clam Ruditapes philippinarum: adaptation mechanisms in cold seep environments

BackgroundThe deep-sea cold seep zone is characterized by high pressure, low temperature, darkness, and oligotrophy. Vesicomyidae clams are the dominant species within this environment, often forming symbiotic relationships with chemosynthetic microbes. Understanding the mechanisms by which Vesicomyidae clams adapt to the cold seep environment is significant. Acetylation modification of lysine is known to play a crucial role in various metabolic processes. Consequently, investigating the role of lysine acetylation in the adaptation of Vesicomyidae clams to deep-sea environments is worthwhile. So, a comparative study of lysine acetylation in cold seep clam Archivesica marissinica and shallow water shellfish Ruditapes philippinarum was conducted.ResultsA total of 539 acetylated proteins were identified with 1634 acetylation sites. Conservative motif enrichment analysis revealed that the motifs -KacR-, -KacT-, and -KacF- were the most conserved. Subsequent gene ontology (GO) and Kyoto encyclopedia of genes and genomes (KEGG) enrichment analyses were conducted on significantly differentially expressed acetylated proteins. The GO enrichment analysis indicated that acetylated proteins are crucial in various biological processes, including cellular response to stimulation, and other cellular processes ( p < 0.05 and false discovery rate (FDR) < 0.25). The results of KEGG enrichment analysis indicated that acetylated proteins are involved in various cellular processes, including tight junction, motor proteins, gap junction, phagosome, cGMP-PKG signaling pathways, endocytosis, glycolysis/gluconeogenesis, among others (p < 0.05 and FDR < 0.25). Notably, a high abundance of lysine acetylation was observed in the glycolysis/glycogenesis pathways, and the acetylation of glyceraldehyde 3-phosphate dehydrogenase might facilitate ATP production. Subsequent investigation into acetylation modifications associated with deep-sea adaptation revealed the specific identification of key acetylated proteins. Among these, the adaptation of cold seep clam hemoglobin and heat shock protein to high hydrostatic pressure and low temperature might involve an increase in acetylation levels. Acetylation of arginine kinase might be related to ATP production and interaction with symbiotic bacteria. Myosin heavy chain (Ama01085) has the most acetylation sites and might improve the actomyosin system stability through acetylation. Further validation is required for the acetylation modification from Vesicomyidae clams.ConclusionA novel comparative analysis was undertaken to investigate the acetylation of lysine in Vesicomyidae clams, yielding novel insights into the regulatory role of lysine acetylation in deep-sea organisms. The findings present many potential proteins for further exploration of acetylation functions in cold seep clams and other deep-sea mollusks.

Impacts of High Temperature and Vapor Pressure Deficit on the Maize Opened Spikelet Ratio and Pollen Viability

High temperatures (HTs) and high vapor pressure deficits (VPDs) have significant impacts on maize yields, partly due to the high sensitivity of maize tassels. However, there are few studies quantifying the impacts of HTs and VPDs on maize tassel performance under changing environments. Therefore, we carried out a two-year field experiment that included 20 inbred lines and four sowing dates. Compared with the first sowing date, the seed set in the second sowing date decreased by ~80% in both years. The opened spikelet ratio (OSR) and pollen viability (PV) were the key determinants of seed set, and their respective correlation coefficients with seed set were 0.58 and 0.90. The OSR and PV decreased by ~20% and ~50%, respectively, under high-temperature stress. When Tmax exceeded 32.5 °C or the VPD exceeded 0.91 KPa, PV began to decline; when Tmax exceeded 33.8 °C or VPD exceeded 1.10 KPa, the OSR began to decline. The OSR was more dependent on genotypic background than PV (28.4% vs. 19.7%). The maize tassel water content was significantly correlated with the OSR and PV. Based on the OSR and PV values, the 20 genotypes were divided into three different groups, namely the high H, middle M, and low L groups. The H group, on average, had the highest kernel number per ear and seed set, followed by the M and L groups. The average seed sets of the H, M, and L genotypes under the second sowing date were 17.4%, 10.9%, and 0%, respectively, in 2019 and 13.8%, 7.9%, and 0.6%, respectively, in 2020. The present results indicate that selecting maize varieties with a high OSR is an effective approach for improving maize yield under heat stress.