Helicopter Electromagnetic Research Articles

Airborne Geophysics over the Dolly Varden VMS and Low Sulphidation Epithermal Silver Deposits, Northwestern BC, Canada

Results from helicopter VTEM time-domain electromagnetics that include aeromagnetics and gamma ray spectrometries and later ZTEM natural field helicopter electromagnetics are compared over the Dolly Varden Mine region that hosts both potential VMS Pb-Zn base metal and low sulphidation epithermal silver mineralization, beyond the known vein-type Ag deposits and showings.There are few well-defined discrete targets within the VTEM data set. The magnetic data have defined a network of older fault structures trending NNE, ENE, WNW, and NW. These structures are interpreted to be related to extensional basin formation. Prominent in the radiometrics is a potassium anomaly over the Red Point area, consistent with a quartz-K-feldspar-chlorite-pyrite zone, interpreted as a VMS feeder. ZTEM resistivity and magnetic geophysical anomalies suggest the presence of broad, generally flat lying resistive and magnetic units at depth. At Red Point and along the Tiger-Evindsen Corridor, ZTEM displays moderate to high resistivity and low magnetics, which suggest the presence of strong potassic-silicic alteration, related to low sulphidation epithermal systems.The airborne geophysical results over the Dolly Varden mine region provide valuable insights on the detectability of similar Ag rich Eskay Creek type HS VMS and Brucejack style LS epithermal deposits. The principal VMS deposits seem immune to clear or discrete identification as EM conductors using VTEM, likely due to their Pb-Zn rich/Cu poor mineralogy; whereas, unlike VTEM, the ZTEM seems to clearly define high resistivity regions surrounding the known deposits that would seem to be consistent with their K-Si-altered low sulphidation epithermal origin.

A Bipolar Half-Sine Current Inverter for Airship-Borne Electromagnetic (AEM) Surveying

A topology of a bipolar half-sine current inverter for geophysical airship-borne transient electromagnetic (EM) surveying is developed. In detail, the RLC series resonance inverter with novelty is designed and analyzed. The key parameters of the output current with very small overshoots and high current amplitude are calculated and simulated, respectively. The results of calculation and simulation agree well with each other. The circuit design and principle analysis of the converter are described clearly. The main reason we choose series resonance current inverter rather than the more common parallel one is that a low-voltage source, such as a standard 28-V dc voltage of the usual aircraft power source, could realize high peak current output through a transient series resonance process efficiently. The proposed current inverter is successfully implemented to the airship-mounted geophysical surveying systems. It achieves a substantial improvement of performance and provides an alternative for the traditional fixed-wing EM systems or helicopter EM systems with much lower cost and higher efficiency. Besides, the experimental results for explorations demonstrate that the measured magnetic field of three axes also agrees well with application requirements of airship-borne EM system.

Helicopter EM (ZTEM–VTEM) survey results over the Nuqrah copper–lead–zinc–gold SEDEX massive sulphide deposit in the Western Arabian Shield, Kingdom of Saudi Arabia

Magnetic and electromagnetic (EM) results from two helicopter EM surveys, a time-domain (VTEM) and AFMAG (ZTEM), are compared over the Nuqrah sedimentary exhalative (SEDEX) massive sulphide deposits in the Western Arabian Shield of the Kingdom of Saudi Arabia. The magnetic and EM data from both surveys map the major controlling structures that host the Nuqrah North and South deposits. Neither Nuqrah deposits stand out as distinctive aeromagnetic anomalies, but both EM surveys define the massive sulphide mineralised vent and bedded portions of the SEDEX orebodies. ZTEM is interpreted to be more capable in defining the larger, lower conductance and less mineralised distal portions of the SEDEX system. The modelled ZTEM also defines a down-dip extension of the Nuqrah South zone below a depth of 750 m.

Not extinct yet: innovations in frequency domain HEM triggered by sea ice studies

The last 15 years have brought major innovations in helicopter towed time domain electromagnetics (EM), while few further developments have been made within the classic frequency domain segment. Operational use of frequency domain EM for sea ice thickness mapping acted as a driving force to develop new concepts such as the system under our consideration. Since its introduction we have implemented new concepts aiming at noise reduction and drift elimination. We decreased signal noise base levels by one to two orders of magnitude with changes to the signal transmission concept. Further, we increased the receiver coil dynamic range creating an EM setup without the need for primary field bucking. Finally, we implemented control signals inside the receiver coils to potentially eliminate system drift. Ground tests demonstrate the desired noise reduction and demonstrate drift control, leading to essentially drift free data. Airborne field data confirm these results, yet also show that the procedures can still be improved. The remaining quest is whether these specialised system improvements could also be implemented in exploration helicopter EM (HEM) systems to increase accuracy and efficiency.

Mapping Saltwater Intrusion in the Biscayne Aquifer, Miami-Dade County, Florida using Transient Electromagnetic Sounding

Saltwater intrusion in southern Florida poses a potential threat to the public drinking-water supply that is typically monitored using water samples and electromagnetic induction logs collected from a network of wells. Transient electromagnetic (TEM) soundings are a complementary addition to the monitoring program because of their ease of use, low cost, and ability to fill in data gaps between wells. TEM soundings have been used to map saltwater intrusion in the Biscayne aquifer over a large part of south Florida including eastern Miami-Dade County and the Everglades. These two areas are very different with one being urban and the other undeveloped. Each poses different conditions that affect data collection and data quality. In the developed areas, finding sites large enough to make soundings is difficult. The presence of underground pipes further restricts useable locations. Electromagnetic noise, which reduces data quality, is also an issue. In the Everglades, access to field sites is difficult and working in water-covered terrain is challenging. Nonetheless, TEM soundings are an effective tool for mapping saltwater intrusion. Direct estimates of water quality can be obtained from the inverted TEM data using a formation factor determined for the Biscayne aquifer. This formation factor is remarkably constant over Miami-Dade County owing to the uniformity of the aquifer and the absence of clay. Thirty-six TEM soundings were collected in the Model Land area of southeast Miami-Dade County to aid in calibration of a helicopter electromagnetic (HEM) survey. The soundings and HEM survey revealed an area of saltwater intrusion aligned with canals and drainage ditches along U.S. Highway 1 and the Card Sound Road. These canals and ditches likely reduced freshwater levels through unregulated drainage and provided pathways for seawater to flow at least 12.4 km inland.

Relevance of AEM and TEM to Detect the Groundwater Aquifer at Faiyum Oasis Area, Faiyum, Egypt

This study investigates the groundwater aquifer located in Fayuim oasis. In this study, two of the electromagnetic measurement methods have been used in determining the hydrological situation in the Fayoum oasis. The first is airborne electromagnetic (AEM) which, sometimes is referred to as Helicopter electromagnetic (HEM) and the second is ground Time-domain Electromagnetic method (TEM). The subsurface consists of four geoelectrical layers with a rough slope towards the center. The third and the fourth layers in the succession are suggested to be the two-groundwater aquifers. The third layer saturates with fresh water overlying saline water which exists in the bottom of the second one. It is worth mentioning that the depth of the fresh water surface undulates between the surface level in two lakes in the study area and 57 meters below the ground, whereas the thickness of the fresh water aquifer varies from 13 to 36 meters. The depth of the saline water surface undulates between 59 and 81 meters below the ground. In general, airborne electromagnetic surveying has the advantage of fast resistivity mapping with high lateral resolution. Groundbased geophysical surveys are often more accurate, but they are definitely slower than airborne surveys. It depends on targets of interest, time, budget, and manpower available by the method or the combination of methods that will be chosen. A combination of different methods is useful to obtain a detailed understanding of the subsurface resistivity distribution.

Appliance of Geophysical Methods to Detect the Ancient Remains at “Tell Defenneh” Area, Ismailia, Egypt

The main target of this study is to detect the ancient archaeological remains by using Helicopter Electromagnetic Method (HEM) and Ground Penetrating Radar (GPR) survey at “Tell Defenneh” Area, which is located in the west bank of Suez Canal at the northeastern Desert of Egypt. It is far about 15 Km to the northeast of “Qantara Gharb” town which is a part of “Ismailia” governorate. This area is full of different archaeological features, because it is located in the ancient international trade-military road (Horus Road). This road connected ancient Egypt with its neighboring eastern countries. In additional to that, this area used to protect ancient Egypt from invaders, who came from the East. HEM has been used to detect the conductivity anomalies over the study area. These anomalies are useful to show the different and distinctive places which can be focused, on small scalar, by GPR to identify it more clearly in the study area. According to the HEM data, it was noticed that there are distinctive geometric shape with very low resistivity or very high conductivity values in the northeastern part of the study area. These data have been supported by GPR survey focused on this part. It was suggested that these anomalies may be due to old man-made mud bricks that was customary used in the building in ancient times. The subsequently archaeological excavations, which are based on these interpreted data as a guide and proof, revealed that the remains belong to the citadel of pharaoh “Psamtik I” (664-610 BC). This result confirms that the incorporated geophysical methods can be efficiently supplied in the archaeological prospection in Egypt.

Developments in frequency domain AEM: Tackling drift and noise with a ferrite-core, receiver triplet.

SUMMARY The polar oceans’ sea ice cover is a challenging geophysical target to map. Current state of practice helicopter-electromagnetic (HEM) ice thickness mapping is limited to 1D interpretation due to common procedures and systems that are mainly sensitive to layered structures. We present a new generation Multi-sensor, Airborne Sea Ice Explorer (MAiSIE) to overcome these limitations. As the actual sea ice structure is 3D and in parts heterogeneous, errors up to 50% are observed due to the common 1D approximation. With MAiSIE we present a new EM concept based on one multi frequency transmitter loop and a three component receiver coil triplet without bucking The small weight frees additional payload to include a line scanner (lidar) and high accuracy INS/dGPS. The 3D surface topography from the scanner with the EM data at from 500 Hz to 8 kHz, in x, y, and z direction, will increase the accuracy of HEM derived pressure ridge geometry significantly. Experience from two field campaigns shows the proof-of-concept with acceptable sensor drift and receiver sensitivity. The preliminary 20 ppm noise level @ 4.1 kHz is sufficient to map level ice thickness with 10 cm precision for sensor altitudes below 13 m.

Application of near-surface geophysics as part of a hydrologic study of a subsurface drip irrigation system along the Powder River floodplain near Arvada, Wyoming

Rapid development of coalbed natural gas (CBNG) production in the Powder River Basin (PRB) of Wyoming has occurred since 1997. National attention related to CBNG development has focused on produced water management, which is the single largest cost for on-shore domestic producers. Low-cost treatment technologies allow operators to reduce their disposal costs, provide treated water for beneficial use, and stimulate oil and gas production by small operators. Subsurface drip irrigation (SDI) systems are one potential treatment option that allows for increased CBNG production by providing a beneficial use for the produced water in farmland irrigation.Water management practices in the development of CBNG in Wyoming have been aided by integrated geophysical, geochemical, and hydrologic studies of both the disposal and utilization of water. The U.S. Department of Energy (DOE) National Energy Technology Laboratory (NETL) and the U.S. Geological Survey (USGS) have utilized multi-frequency airborne, ground, and borehole electromagnetic (EM) and ground resistivity methods to characterize the near-surface hydrogeology in areas of produced water disposal. These surveys provide near-surface EM data that can be compared with results of previous surveys to monitor changes in soils and local hydrology over time as the produced water is discharged through SDI.The focus of this investigation is the Headgate Draw SDI site, situated adjacent to the Powder River near the confluence of a major tributary, Crazy Woman Creek, in Johnson County, Wyoming. The SDI system was installed during the summer of 2008 and began operation in October of 2008. Ground, borehole, and helicopter electromagnetic (HEM) conductivity surveys were conducted at the site prior to the installation of the SDI system. After the installation of the subsurface drip irrigation system, ground EM surveys have been performed quarterly (weather permitting). The geophysical surveys map the heterogeneity of the near-surface geology and hydrology of the study area. The geophysical data are consistent between surveys using different techniques and between surveys carried out at different times from 2007 through 2011. This paper summarizes geophysical results from the 4-year monitoring study of the SDI system.

A combined approach of remote sensing and airborne electromagnetics to determine the volume of polynya sea ice in the Laptev Sea

Abstract. A combined interpretation of synthetic aperture radar (SAR) satellite images and helicopter electromagnetic (HEM) sea-ice thickness data has provided an estimate of sea-ice volume formed in Laptev Sea polynyas during the winter of 2007/08. The evolution of the surveyed sea-ice areas, which were formed between late December 2007 and middle April 2008, was tracked using a series of SAR images with a sampling interval of 2–3 days. Approximately 160 km of HEM data recorded in April 2008 provided sea-ice thicknesses along profiles that transected sea ice varying in age from 1 to 116 days. For the volume estimates, thickness information along the HEM profiles was extrapolated to zones of the same age. The error of areal mean thickness information was estimated to be between 0.2 m for younger ice and up to 1.55 m for older ice, with the primary error source being the spatially limited HEM coverage. Our results have demonstrated that the modal thicknesses and mean thicknesses of level ice correlated with the sea-ice age, but that varying dynamic and thermodynamic sea-ice growth conditions resulted in a rather heterogeneous sea-ice thickness distribution on scales of tens of kilometers. Taking all uncertainties into account, total sea-ice area and volume produced within the entire surveyed area were 52 650 km2 and 93.6 ± 26.6 km3. The surveyed polynya contributed 2.0 ± 0.5% of the sea-ice produced throughout the Arctic during the 2007/08 winter. The SAR-HEM volume estimate compares well with the 112 km3 ice production calculated with a~high-resolution ocean sea-ice model. Measured modal and mean-level ice thicknesses correlate with calculated freezing-degree-day thicknesses with a factor of 0.87–0.89, which was too low to justify the assumption of homogeneous thermodynamic growth conditions in the area, or indicates a strong dynamic thickening of level ice by rafting of even thicker ice.

Progressing from 1D to 2D and 3D near-surface airborne electromagnetic mapping with a multisensor, airborne sea-ice explorer

The polar ocean’s sea ice cover is an unconventional and challenging geophysical target. Helicopter electromagnetic (HEM) sea-ice thickness mapping is currently limited to 1D interpretation due to traditional procedures and systems. These systems are mainly sensitive to layered structures, ideally set for the widespread flat (level) ice type. Because deformed sea ice (e.g., pressure ridges) is 3D and usually also heterogeneous, ice thickness errors up to 50% can be observed for pressure ridges using 1D approximations for the interpretation of HEM data. We researched a new generation multisensor, airborne sea ice explorer (MAiSIE) to overcome these limitations. Three-dimensional finite-element modeling enabled us to determine that more than one frequency is needed, ideally in the range 1–8 kHz, to improve thickness estimates of grounded sea-ice pressure ridges that are typical of 3D sea ice structures. With the MAiSIE system, we found a new electromagnetic concept based on one multifrequency transmitter loop and a 3C receiver coil triplet with active digital bucking. The relatively small weight of the EM components freed enough payload to include additional scientific sensors, including a cross-track lidar scanner and high-accuracy inertial-navigation system combined with dual-antenna differential GPS. Integrating the 3D ice-surface topography obtained from the lidar with the EM data at frequencies from 500 Hz to 8 kHz in [Formula: see text]-, [Formula: see text]-, and [Formula: see text]-directions, significantly increased the accuracy of sea-ice pressure-ridge geometry derived from HEM data. Initial test flight results over open water showed the proof-of-concept with acceptable sensor drift and receiver sensitivity. Noise levels were relatively high (20–250 parts-per-million) due to unwanted interference, leaving room for optimization. The 20 ppm noise level at 4.1 kHz is sufficient to map level ice thickness with 10 cm precision for sensor altitudes below 13 m.

Near-surface electromagnetic induction — Introduction

There has been explosive growth in near-surface electromagnetic (EM) induction geophysics in the past several years (Everett, 2012). New and experienced practitioners are achieving great success in applying the method to an increasing variety of problems. Moreover, theorists are becoming better able to exploit the rich information content that is available in electromagnetic induction data sets. The EM induction method, with its broad opportunities to design new transmitters, receivers, and interpretation tools, continues to offer wide avenues to capture the spatial complexity of the subsurface. This special Geophysics issue brings forward the latest achievements, which should stimulate interest across a broad spectrum of geophysicists, as well as set the tone for continuing developments in this field. This special issue contains advances in theory, instrumentation, data processing and interpretation, and innovative applications of near-surface applied EM induction geophysics. The range of topics is varied and, as described below, includes modeling and inversion, airborne electromagnetics, hydrogeophysics, soil science, audiomagnetotellurics, unexploded ordnance (UXO) discrimination, archaeology, geothermal mapping, and joint inversion of EM and magnetic resonance sounding data. Vrbancich analyzes helicopter time-domain EM data acquired over shallow seawater overlying reefs and sediment-filled paleovalleys. A favorable comparison is shown of water depths and sediment thickness derived from 1D inversion with known bathymetry and independent marine seismic …

Helicopter electromagnetic data map ice thickness at Mount Adams and Mount Baker, Washington, USA

AbstractIce-thickness measurements critical for flood and mudflow hazard studies are very sparse on Cascade Range (North America) volcanoes. Helicopter electromagnetic (HEM) data collected to detect hydrothermal alteration are used to determine ice thickness over portions of Mount Baker and Mount Adams volcanoes. A laterally continuous inversion method provides good estimates of ice <100 m thick over water-saturated and altered regions where the resistivity of the basement is <200 Ωm. For areas with ice overlying fresh, resistive rocks with small resistivity contrasts between ice and rock, ice thickness is not well resolved. The ice thicknesses derived from HEM data are consistent with the previous drillhole data from Mount Adams and radar data from both volcanoes, with mean thicknesses of 57 m for Mount Adams and 68 m for Mount Baker. The thickest ice on Mount Baker rests on the gentle lower slopes whereas the thickest ice at Mount Adams lies on the flat summit. Ice volume calculations suggest that Mount Baker contains ∽710 × 106 m3 of ice in the HEM survey area, with a crude estimate of ∽1800 × 106m3 for the entire volcano. Ice volume on Mount Adams is 65 × 106m3 in parts of the HEM survey area and ∽200 × 106m3 overall.

Imaging a 3D geological structure from HEM, airborne magnetic and ground ERT data in Kalat-e-Reshm area, Iran

Abstract A set of geophysical data collected in an area in Iran are analyzed to check the validity of a geological map that was prepared in connection to a mineral prospecting project and also to image the spatial electrical resistivity distribution. The data set includes helicopter electromagnetic (HEM), airborne magnetic and ground electrical resistivity measurement. Occam approach was used to invert the HEM data to model the resistivity using a layered earth model with fixed thicknesses. The algorithm is based on a nonlinear inverse problem in a least-squares sense. The algorithm was tested on a part of an HEM dataset acquired with a DIGHEM helicopter EM system at Kalat-e-Reshm, Semnan in Iran. The area contains a resistive porphyry andesite that is covered by Eocene sedimentary units. The results are shown as resistivity sections and maps confirming the existence of an arc like resistive structure in the survey area. The resistive andesite seems to be thicker than it is indicated in the geological maps. The results are compared with the reduced to the pole (RTP) airborne magnetic anomaly field data as well as with two ground resistivity profiles. We found reasonable correlations between the HEM 1D resistivity models and 2D models from electrical resistivity tomography (ERT) inversions. A 3D visualization of the 1D models along all flight lines provided a useful tool for the study of spatial variations of the resistivity structure in the investigation area.

Metalliferous mining geophysics — State of the art after a decade in the new millennium

Mining exploration was very active during the first decade of the twenty-first century because there were numerous advances in the science and technology that geophysicists were using for mineral exploration. Development came from different sources: instrumentation improvements, new numerical algorithms, and cross-fertilization with the seismic industry. In gravity, gradiometry kept its promise and is on the cusp of becoming a key technology for mining exploration. In potential-field methods in general, numerous techniques have been developed for automatic interpretation, and 3D inversion schemes came into frequent use. These inversions will have even greater use when geologic constraints can be applied easily. In airborne electromagnetic (EM) methods, the development of time-domain helicopter EM systems changed the industry. In parallel, improvements in EM modeling and interpretation occurred; in particular, the strengths and weaknesses of the various algorithms became better understood. Simpler imaging schemes came into standard use, whereas layered inversion seldom is used in the mining industry today. Improvements in ground EM methods were associated with the development of SQUID technology and distributed-acquisition systems; the latter also impacted ground induced-polarization (IP) methods. Developments in borehole geophysics for mining and exploration were numerous. Borehole logging to measure physical properties received significant interest. Perhaps one reason for that interest was the desire to develop links between geophysical and geologic results, which also is a topic of great importance to mining geologists and geophysicists.

Using helicopter electromagnetic (HEM) surveys to identify potential hazards at coal-waste impoundments: Examples from West Virginia

We have used 14 multifrequency helicopter-borne electromagnetic (HEM) surveys to determine the internal structure and integrity of mine-impoundment structures in West Virginia, U.S.A. — the first time such technology has been applied in this way and apparently well suited for such activities. The HEM surveys identified areas of concern in each of the impoundments investigated. In most cases, these were areas where filtrate was emerging high on the downstream embankment and represented an erosion risk. Of greater concern, the HEM survey identified thick bodies of slurry that remained unconsolidated and were buried deep beneath the embankment’s crest of some impoundments. Ground confirmation activities indicated that HEM survey interpretations provided an accurate representation of the conductivity distribution within coal-waste impoundments. We then interpreted the conductivity/depth images from the HEMsurveys to provide a snapshot of hydrologic conditions that existed within the impoundment at the time of the survey. Resistivity profiles were obtained at the inactive impoundment along segments of flight lines from the HEM survey. HEM and resistivity surveys detected a conductive layer at a depth of about [Formula: see text] that was interpreted to be unconsolidated coal slurry. The methods also detected conductive bodies at a depth of about [Formula: see text] that were interpreted to be flooded mine works. Resistivity surveys from these segments corroborated HEM data, thereby providing independent confirmation of the HEM data and its processing. The resistivity and HEM surveys indicated a resistive surface layer where the coarse coal refuse was placed. Beneath the resistive surface layer is a conductive layer of unconsolidated or partially consolidated coal slurry. These highly loaded bodies of unconsolidated slurry are susceptible to solifluction, which can threaten embankment stability. Underground mine workings were identified in the HEM data from one impoundment.

A comparative study of in-river geophysical techniques to define variations in riverbed salt load and aid managing river salinization

Increased interest in the character of sediments at the base of waterways, for the purpose of managing river salinization, has led to the application of several geophysical techniques for collecting information from this zone. These instream methods are based on established ground and airborne electrical and electromagnetic technologies, including towed transient electromagnetic systems, towed direct current resistivity array systems, and frequency-domain helicopter electromagnetic systems. Although these systems are individually successful, a systematic examination of their relative effectiveness for identifying variations in substrate conductivity for a common stretch of a river remains lacking. We have compared results obtained from data collected using three instream geophysical techniques for a common stretch of the Murray River in southeastern Australia. The Murray River is an important water resource for drinking and agricultural purposes. Data from these surveys were acquired tolocate areas of significant saltwater accession to the Murray from a saline regional groundwater system that discharges into it. The three methods indirectly inform on those reaches that most likely contribute to higher salt loads in the river, and they do this through the identification of a conductive substrate (a gaining reach). For a [Formula: see text] stretch of the river, the methods identified similar variations in the conductivity structure of sediment substrate, although differences were observed in the modeled response relating to intrinsic differences between each system, including the sampling interval and resolution. The helicopter electromagnetic (EM) system is capable of acquiring hundreds of kil-ometers of data in a day, under any river flow condition, from near the river surface to depths in excess of [Formula: see text]. The other two techniques require safe river flow conditions for acquisition, with as much as 50 river km of data per day possible. The ground-based methods had enhanced lateral and vertical resolving capabilities relative to the helicopter EM system, but their depth of investigation was less (usually only [Formula: see text]).

Using helicopter electromagnetic data to predict groundwater quality in fractured crystalline bedrock in a semi-arid region, Northeast Brazil

Geostatistical modeling, using airborne and borehole electromagnetic data, was used to estimate electrical conductivity in groundwater within fractured paragneisses and migmatites in a semi-arid climate in northeastern Brazil. Despite the geologic heterogeneity of crystalline aquifers, the use of high resolution helicopter electromagnetic (HEM) data enabled the characterization of groundwater electrical conductivity where data from drilled wells were insufficient. The tacit assumption is that HEM measurements can be used to relate rock electrical conductivity to groundwater electrical conductivity. In this study, the HEM data were used as an external drift variable in non-stationary estimation and stochastic simulation to identify the variability of groundwater electrical conductivity. Validation tests, comparing predicted values for groundwater conductivity with measurements in new wells, confirmed the success of these models in locating fresh groundwater sources in crystalline bedrock.

Spatial modelling incorporating AEM data to show the effects of manipulating flow regimes and groundwater lowering options over the Chowilla floodplain, SA

Along the floodplains of the Murray River in south eastern Australia, where the saline groundwater system is particularly close to the surface, evapotranspiration concentrates salt resulting in extensive salinisation, vegetation dieback or health decline. In many floodplain areas, ecologically important woodland species that inhabit the floodplain are dying from soil water salt concentrations that often exceed those of seawater. To better manage this problem and to protect the ecology and biodiversity on the floodplains along the river, a range of management strategies are being employed. Modelling tools are integral to their development, but key to their effectiveness is the availability of detailed biophysical data. In a study focussed on the Chowilla Floodplain in South Australia, WINDS, a spatial model that examines soil water availability was employed to show the possible effects of manipulating flow regimes and groundwater lowering options across the whole of the floodplain. We examined the value of using biophysical parameters derived from the helicopter electromagnetic (HEM) data, specifically groundwater conductivity and salt storage for specific zones in the saturated, capillary and unsaturated parts of the floodplain, as a basis for making vegetation health assessments or predictions at any particular time. The procedure for deriving this information in 3D is discussed.

Sea ice as an evaluation target for HEM modelling and inversion

We investigate helicopter electromagnetic (HEM) inversion schemes applied to synthetic and measured HEM sea ice profiling data. Direct HEM data-to-ice-thickness inversion is compared to three different formal, least squares layered earth inversion algorithms. By making several approximations, it is possible to directly invert a single channel measurement (i.e., the in-phase or quadrature component of a single frequency measurement) to obtain an estimate of sea ice thickness. Measurements from multiple input channels, however, can be used in a layered earth inversion to simultaneously recover several model parameters such as sea ice thickness, sea ice conductivity and sub-ice bathymetry. Synthetic data sets for a particular two-frequency HEM system showed that simple least squares inversion algorithms produce reliable estimates of sea ice thickness in cases where the ice is thicker than 3 m. These methods could also recover acceptable estimates of sea ice thickness when a thin, conductive, partially melted sea ice layer was present, and could determine shallow, sub-ice bathymetry in brackish water. As expected, 1D transformations and inversions of synthetic data for a three-dimensional pressure ridge keel structure contained artifacts, notably broadening of the apparent width of the keel. Prior to inverting a field data set acquired over rather thin (~ 0.5 m) Antarctic sea ice, we found it necessary to recalibrate the phase angle of the measurements using a phasor diagram-based method. Direct transformation of a single channel from the recalibrated data set produced more accurate estimates of sea-ice thickness than formal inversion of multi-channel data. We suggest that the least squares inversion methods are inferior in this situation because of the particular characteristics of the two-frequency HEM system used in this evaluation; the extreme differences in sensitivity of high and low frequency data components, the overall low sensitivity to sea ice conductivity (especially for thin ice), and the partially low signal-to noise ratios of the measurements. The data sets used in this study will be made available to the public to allow alternate inversion approaches to be applied and evaluated. It is suggested that inclusion of parameter bounds and other forms of regularization could help to improve the inversion results.