Heavy Metals Zn Research Articles

Experimental study on the dynamic strength characteristics of combined heavy metals contaminated soil with nZVI treatment

Nanoscale zero-valent iron (nZVI), a high-performance nanomaterial, can treat heavy metal contaminants and is extensively employed for in-situ treatment of groundwater and contaminated subsoil. However, there are few studies that indicate trends in the dynamic strength parameters of nZVI-treated soils to assess site safety. In this study, three heavy metal contaminants, Zn(II), Pb(II), and Ni(II), were selected to contaminate virgin soil. The heavy-metal-contaminated soil was treated with nZVI at two concentrations (a low dose and high dose of 0.5% and 2%, respectively) of the soil's dry mass. Analyses of particle size distribution revealed a consistent shift towards larger particles upon nZVI treatment, and the percentage of sand gradually increased. Heavy metal contamination decreased the liquid and plastic limits of the virgin soil, while those of the treated soil increased with nZVI content. The dynamic triaxial results showed significantly lower maximum dynamic shear modulus for MS, MS-LdN, and MS-HdN than for NS. The damping ratios of all samples showed an S-shaped trend. Thus, nZVI has the potential to create cemented structures and immobilize heavy metals. However, its effectiveness is significantly modulated by the initial water content of the soil. While the application of nZVI proves beneficial in immobilizing heavy metal contaminants, careful consideration is imperative under dynamic loading conditions.

Estimation of the level of anthropogenic impact based on the determination of radionuclides and heavy metals in sediments taken from Rybnik reservoir, Poland

The aim of the study was to estimate the degree of anthropogenic risk by evaluating the level of the contamination of sediments collected from the Rybnik reservoir. The results of the determination of radionuclides (137Cs, 40K, 228Th, 228Ra, 226Ra, 210Pb, 238U) and heavy metals (Zn, Cd, Pb, Cu, Cr, Ni) were presented. The Rybnik reservoir is located in a highly urbanised area, the Lower Silesian Voivodeship in Poland. Radionuclides (137Cs, 40K, 228Th, 228Ra, 226Ra, 210Pb, 238U) were measured using gamma spectrometry. The heavy metal (Zn, Cd, Pb, Cu, Ni and Cr) content was determined using an inductively coupled plasma optical emission spectrophotometer (ICP-OES). The classification of sediment pollution was made on the basis of geochemical and ecotoxicological indices. Radioactivity was varied with the highest for 40K (more than 200 Bq·kg−1). The concentrations for the remaining radionuclides were mostly below 20 Bq·kg−1. At the inlet zone (no. 9) an increase in radioactivity of each radioisotope was observed. The values of heavy metals from the lowest to the highest total amount in the sediments were as follows: Cd < Cr < Pb < Ni < Cu < Zn. The sediments of the reservoir are largely contaminated with Cu, but the sediments generally are contaminated to an average degree. Most pollutants accumulate in the inlet zone and near the dam wall. The content of artificial radionuclides, as well as the geochemical and ecological indicators used, can serve as an indicator of the level of anthropopressure in the vicinity of the Rybnik reservoir.

Assessment of Heavy Metal Contamination and Health Risk Associated with Cultivated Vegetables along Dhaka-Mymensingh Highway, Bangladesh.

The purpose of this research work is to evaluate the degree of eight heavy metals (Fe, Mn, Cu, Zn, Cd, Pb, Cr, and Ni) contamination and health risks of three regularly consumed vegetables (papaya, bottle gourd, and esculent) near one of Bangladesh's busiest roadways, the Dhaka-Mymensingh highway. The heavy metal concentrations in 45 vegetable samples were analyzed using an atomic absorption spectrometer (AAS). These samples were collected from five different sampling sites based on various land use patterns adjacent to the highway. The average concentrations (mg/kg) of Cu, Fe, Mn, Zn, Cr, and Ni were found to be 9.86, 246.8, 16.9, 28.0, 9.02, and 2.02, respectively, for papaya; 14.9, 281.2, 387.6, 49.0, 10.1, and 2.92, respectively, for bottle gourd; and 17.6, 183.4, 107.2, 80.7, 7.98, and 2.34, respectively, for esculent. The mean concentrations of Cr, Zn, and Mn in papaya, bottle gourd, and esculent were higher than the acceptable limit. Correlation analysis revealed a significant positive correlation between Fe-Cu, Zn-Fe, Cu-Fe, and Fe-Zn in papaya; Cu-Zn, Fe-Cr, Zn-Ni, and Cr-Fe in bottle gourd; and Mn-Cr, Mn-Ni, Mn-Fe, and Cr-Ni in esculent, thereby indicating their common anthropogenic sources like agricultural activities, waste from the commercial area, filling station, and vehicular emissions. Health risk assessment through target hazard quotient (THQ) revealed the highest THQ of 9.52 for Cr in bottle gourd, which poses a high non-carcinogenic health risk to the localities upon the intake of these contaminated vegetables. Target cancer risk (TCR) was found to be highest for Cr in papaya (0.013) and bottle gourd (0.014). TCR trends were found for Cr in the following order: bottle gourd > esculent > papaya. This study contributed the greatest concern for both carcinogenic and non-carcinogenic health impacts through ingesting contaminated vegetables.

Resource utilization of MSWI fly ash supporting TiO2/BiOCl nanocomposite for enhanced photocatalytic degradation of sodium isopropyl xanthate: Mechanism and performance evaluation

The removal of organic pollutants in water environments and the resource utilization of solid waste are two pressing issues around the world. Facing the increasing pollution induced by discharge of mining effluents containing sodium isopropyl xanthate (SIPX), in this work, municipal solid waste incineration fly ash (MSWI FA) was pretreated by hydrothermal method to produce stabilized FA, which was then innovatively used as support for the construction of FA/TiO2/BiOCl nanocomposite (FTB) with promoted photocatalytic activity under visible light and natural sunlight. When the content of FA was 20 wt% and the mass ratio of TiO2 to BiOCl was 4:6, a remarkable performance for the optimal FTB (20-FTB-2) was achieved. Characterizations demonstrated that TiO2 and BiOCl uniformly dispersed on FA contributing to high surface area and broad light adsorption of FTB, which exhibits excellent adsorption capacity and light response ability. Build in electric field formed in the interface of TiO2/BiOCl heterojunction revealed by density functional theory calculations accelerated the separation of photoinduced e− and h+, leading to high efficiency for SIPX degradation. The synergetic effect combined with adsorption and photocatalytic degradation endowed 20-FTB-2 superior SIPX removal efficiency over 99% within 30 min under visible light and natural sunlight irradiation. The photocatalytic degradation pathways of SIPX were determined through theoretical calculations and characterizations, and the toxic byproduct CS2 was effectively eliminated through oxidation of •O2−. For 20-FTB-2, reusability of photocatalyst was showed by cycle tests, also the concentrations of main heavy metals (Pb, Zn, Cu, Cr, and Cd) in the liquid phases released during photocatalyst preparation process (< 1 mg/L) and photodegradation process (< 8.5 μg/L) proved the satisfactory stability with low toxicity. This work proposed a novel strategy to develop efficient and stable support-based photocatalysts by utilizing MSWI FA and realize its resource utilization.

Heavy metal levels and human health risk implications associated with fish consumption from the lower Omo river (Lotic) and Omo delta lake (Lentic), Ethiopia.

This study is the first to determine the levels of heavy metals in commercially important fish species, namely Lates niloticus and Oreochromis niloticus and the potential human health risks associated with their consumption. A total of 120 fish samples were collected from the lower Omo river and Omo delta, with 60 samples from each water source. The fish tissue samples (liver and muscle) were analyzed using a flame atomic absorption spectrometer for nine heavy metals (Cd, Co, Cr, Cu, Fe, Mn, Ni, Pb, and Zn). The human health risk assessment tools used were the target hazard quotient (THQ), the hazard index (HI), and the target cancer risk (TCR). The mean levels of heavy metals detected in the liver and muscle of L. niloticus from the lower Omo river generally occurred in the order Fe > Zn > Pb> Cu > Mn> Cr > Co > Ni and Pb > Cu > Mn > Co > Ni, respectively. The mean levels of metals in the muscle and liver tissues of O. niloticus were in the order Fe > Pb > Zn > Mn > Cu > Cr > Co > Ni and Pb > Zn > Mn > Fe > Cu > Co > Ni, respectively. Similarly, the mean levels of heavy metals detected in the liver and muscle of L. niloticus from Omo delta occurred in the order Fe > Zn > Pb > Cu > Mn > Cr > Co > Ni and Fe > Pb > Zn > Mn > Cu > Co > Cr > Ni, respectively. The mean levels in the muscle and liver tissues of O. niloticus from the Omo delta were in the order Fe > Pb > Zn > Mn > Cu > Cr > Co > Ni and Pb > Fe > Zn > Mn > Co > Cu > Ni, respectively. The study revealed that the THQ values were below 1, indicating that consumption of L. niloticus and O. niloticus from the studied sites does not pose a potential non-carcinogenic health risk. Although the TCR values for Pb in this study were within the tolerable range, it's mean concentration in the muscle and liver tissues of both fish species from the two water bodies exceeded the permissible limit established by FAO/WHO. This is a warning sign for early intervention, and it emphasizes the need for regular monitoring of freshwater fish. Therefore, it is imperative to investigate the pollution levels and human health risks of heavy metals in fish tissues from lower Omo river and Omo delta for environmental and public health concerns.

Use of Vetevera Grass (Chrysopogon zizanioides) in a Constructed Wetland to Remove Heavy Metals from Kege Wet Coffee Processing Plant, Dale Woreda, Sidama Regional State, Ethiopia

Conventional methods for removing heavy metals from contaminated water are prohibitively expensive and, more significantly, ineffective, especially when the concentration of heavy metals is low. This paper evaluated the use of vetevera grass in a constructed wetland to remove Ca, Cd, Co, Cu, Cr, Fe, K, Mn, Na, Pb, and Zn metals from Kege Wet Coffee Processing Plant, Dale Woreda, Sidama Regional State, Ethiopia using a two vertical flows constructed wetland of 132 square meters in size with Eleven meters in length and 12 meters wide. The 11m * 3m * 1m open space between two constructed wetlands is developed. The second wetland was built, and it serves the same purpose as the previous one but discharges water into the river. The construction of the wetland is performed by digging 20 cm wide, and 30 cm apart furrows. vetiveria grasses was planted at 20 cm intervals. Heavy metals (Ca, Cd, Co, Cu, Cr, Fe, K, Mn, Na, Pb, and Zn) were measured from soil and plant samples from the inlet to the outlet sampling sites using standard procedures from two compartments (soil, and macrophytes) of constructed wetland. Findings indicated that Ca (460.0 ppm) had the highest mean concentration of heavy metals, whereas Ni (0.50 ppm) had the lowest in the soil sample. Metal absorption by vetiver grass is the highest concentration found in plant tissues grown in the following order k &gt; Ca &gt; Na &gt; Mn &gt; Fe &gt; Zn &gt; Cu &gt;Ni &gt;Cr in shoots. The order of the heavy metal contents in the roots of vetiver grass was k &gt; Ca &gt; Na &gt; Mn &gt; Fe &gt; Zn &gt; Cu &gt;Ni &gt;Cr. The plant was found to be effective at transferring Mn and Ni from the roots to the shoots based on translocation and bioconcentration, whereas it served as a potential phytostabilizer for Ca, Cu, Cr, Fe, K, Na, and Zn since the TF values are lower than 1, which show that vetiver grass prefers to accumulate heavy metals in the roots rather than the shoot and so supports its potential for phytostabilization. From the present study, it was evident that vetiver grass is an ideal candidate for wastewater treatment using constructed wetland technology.

Repurposing spent biomass of vetiver grass used for stormwater treatment to generate biochar and ethanol

Stormwater pollution is a key factor contributing to water quality degradation, posing substantial environmental and human health risks. Although stormwater retention ponds, also referred to as wet ponds, are commonly implemented to alleviate stormwater challenges by reducing peak flow and removing suspended solids, their effectiveness in removing heavy metals and nutrients is limited. This study evaluated the performance of floating treatment platforms (FTPs) featuring vetiver grass (Chrysopogon zizanioides), a non-invasive, nutrient- and metal-accumulating perennial grass, in removing heavy metals (Cu, Pb, and Zn) and nutrients (P and N) in stormwater retention ponds. Furthermore, the potential for utilizing the spent vetiver biomass for generating biochar and bioethanol was investigated. The study was conducted in a greenhouse setup under simulated wet and dry weather conditions using pond water collected from a retention pond in Stafford Township, New Jersey, USA. Two FTPs with vetiver (vegetated FTPs) were compared with two FTPs without vetiver (non-vegetated FTPs), which served as controls. Results showed that the removal of heavy metals and nutrients by the FTPs with vetiver was significantly higher (p < 0.05) than the FTPs without vetiver. Notably, vetiver showed resilience to stormwater pollutants and hydroponic conditions, displaying no visible stress symptoms. The biochar and bioethanol generated from the spent vetiver exhibited desirable yield and quality, without raising concerns regarding pollutant leaching, indicated by very low TCLP and SPLP concentrations. This study provides compelling evidence that the implementation of vetiver-based FTPs offers a cost-effective and environment-friendly solution for mitigating stormwater pollution in retention ponds. Furthermore, the utilization of vetiver biomass for biofuel and biochar production supports clean production and fostering circular economy efforts.

Worldwide Examination of Magnetic Responses to Heavy Metal Pollution in Agricultural Soils

Over the last decade, a large number of studies have been conducted on heavy metals and magnetic susceptibility (χlf) measurement in soils. Yet, a global understanding of soil contamination and magnetic responses remains elusive due to the limited scope or sampling sites of these studies. Hence, we attempted to explore a pollution proxy on a global scale. Through a meta-analysis of data from 102 published studies, our research aimed to provide a worldwide overview of heavy metal pollution and magnetic responses in agriculture soils. We mapped the geographic distribution of nine heavy metals (Cr, Cu, Zn, Pb, Ni, As, Cd, Mn, and Fe) in agricultural soils and explored their pollution sources and contributions. Since 2011, The accumulation of heavy metals has escalated, with industrial activities (31.5%) being the largest contributor, followed by agricultural inputs (27.1%), atmospheric deposition (22.66%), and natural sources (18.74%). The study reports χlf ranging from 6.45 × 10−8 m3/kg to 319.23 × 10−8 m3/kg and χfd from 0.59% and 12.85%, with the majority of the samples being below 6%, indicating heavy metal influence mainly from human activities. Pearson’s correlation and redundancy analysis show significant positive correlations of Pb, Zn, and Cu with χlf (r = 0.51–0.53) and Mn and Fe with χfd (r = 0.50–0.53), while Pb, Zn, Cu, and As metals were shown to be key factors of variation in magnetic response. The average heavy metal pollution load index of 2.03 suggests moderate global agricultural soil pollution, with higher heavy metal contamination in areas of high χlf. Regression analysis confirms soil is considered to be non-polluted below χlf of 26×10−8 m3/kg and polluted above this threshold, with all contamination factors of metals showing a linear correlation with χlf (R = 0.72), indicating that a significant relationship between χlf and the geochemical properties of soils continues to exist on a global scale. This study provides new insights for large-scale agricultural soil quality assessment and magnetic response.

Isolation and molecular characterization of heavy metal tolerant bacteria from Kofar Ruwa scrap metal dump site in Kano Metropolis

This study aimed at molecular detection of heavy metal tolerant bacteria from Kano, Kofar Ruwa scrap metal dump site, as heavy metals are one of the major setbacks to many forms of lives and their presence in the ecosystem is rapidly increasing due to anthropogenic activities, rampant scrap metal waste disposal and other industrial wastes. Bacteria were found to be among many microorganisms that are able to tolerate many heavy metals and can reduce their toxicity or even convert them to useful resources. The heavy metal content of some soil samples analyzed using Atomic Absorption Spectrophotometry (AAS). Standard methods of enrichment culture and colony count were used to isolate a total of 12 bacterial species. Using 16S rRNA gene sequence based on molecular system, the 12 isolates were identified and grouped into one genus (Bacillus). It was also observed and reported from the results that the concentration of heavy metals (Pb, Zn, Cu, Cd, and Cr) found to be high above the WHO permissible limits (Copper-2.0, Zinc-3.0, Lead-0.4, Chromium-0.05 and Cadmium-0.03). Therefore, the bacterial isolates capable of surviving at such levels of heavy metals could have potential application in the bioremediation, bioleaching, human carcinogens substances and soil infertility of heavy metal contaminants . It is therefore, recommended that further research on these bacterial species should be carried out to address their significance for the public health interest and humanity in general.

Safety of Tap Water in Terms of Changes in Physical, Chemical, and Biological Stability

Monitoring the quality of tap water in the distribution system and the ability to estimate the risk of losing its sanitary safety is an important aspect of managing the collective water supply system. During monitoring, the physical, chemical, and biological stability of water was assessed, which is the main determinant ensuring the appropriate quality of water for consumers. The physicochemical and microbiological quality of water was analyzed for two distribution systems (DSs), including the analysis of heavy metals (Zn, Fe, Mn, Cr, Ni, Cu, Cd, Pb). The tests carried out showed that in both distribution systems, the water supplied to consumers met the guidelines for water intended for human consumption. It can be considered that the risk of uncontrolled changes in water quality in DSs with an average water production of &lt;10,000 m3/d and the length of water pipelines &lt; 150 km is very low. The water introduced into the system differed in the place of water intake and water purification technology, which influenced the final water quality. In DS(II), higher values were recorded for hardness, conductivity, calcium, alkalinity, nitrates, and DOC. It was found that the content of heavy metals during water transport to the consumer increased in the case of DS(I) for Zn, Ni, Cu, Cd, and Pb, and in the case of DS(II) for Fe, Mn, Ni, Cu, Cd, and Pb. The observed differences resulted from the different quality of the intake water as well as from different materials used to build internal installations and their age and technical condition. The analyzed tap water was characterized by physical and chemical stability. However, the water did not meet the guidelines for water biostability due to the increased content of biogenic substances.

Detection of Heavy Metals in Some Edible Grains Obtained from Two Markets in Bauchi Metropolis, Nigeria

This study investigated the level of heavy metals (Cd, Cr, Cu, Fe, Pb and Zn) in grains sold in Central and Muda Lawal markets in Bauchi. Our objectives include assessing heavy metal concentrations in the grains and evaluating associated health risks. We utilized Atomic Absorption Spectrophotometry following acid digestion of grains to determine heavy metal concentrations. In Central market-sourced crops, the mean concentrations of Cd, Cr, Cu, Fe, Pb, and Zn were 0.06, 0.49, 0.21, 1.16, 0.15, and 0.17mg/kg respectively. Meanwhile, crops from Muda Lawal market exhibited mean concentrations of 0.06, 0.58, 0.17, 1.62, 0.1, and 0.22 mg/kg for Cd, Cr, Cu, Fe, Pb, and Zn, respectively. Cd, Cr, Cu, Pb, and Zn levels were below the permissible limits. However, Fe exceeded permissible limits in small beans, Syria maize, and white guinea corn from Central market, as well as in Syria maize, Pearl millet II, and white guinea corn from Muda Lawal market. The daily intake of Cd, Cu, and Pb from most studied crops exceeded the oral reference dose, posing potential health risks. Conversely, Cr, Fe, and Zn intake levels were within acceptable limits, posing minimal health risks. Hazard quotient and hazard index values were below 1, suggesting that crop consumption is unlikely to pose health risks.

Impact of recurring irrigation with treated domestic wastewater on heavy metal accumulation in the soil

Water reuse for irrigation is a common practice globally, serving as an alternative to clean water. Wastewater contains traces of heavy metals that accumulate in the soil and food chain, posing an environmental and public risk. This study investigated the effect of irrigation with treated domestic wastewater (TDW) emanating from a homogenous community on heavy metal accumulation in the soil irrigated for three recurring farming cycles, namely R1, R2, and R3. A greenhouse experiment was conducted involving plots irrigated with TDW (PTw) and plots irrigated with fresh water (PFw) in triplicate. Soil samples were collected at depths of 0–20, 20–40, and 40–60 cm. Results revealed that heavy metals Pb, Cu, Cr, Zn, Cd, and Ni remained within the WHO permissible limits in the PTw and PFw, except Cd at 40–60 cm after the R3 in the TPw. Irrigation with TDW caused a decrease in Pb and Cd with respect to the baseline levels by 86–91% and 88–96% respectively. Other heavy metals increased in the soil in the order of Cr>Cu>Ni>Zn at 0–20 cm, Cr>Cu>Zn>Ni at 20–40 cm, and Cr>Cu>Ni>Zn at 40–60 cm. Variations in heavy metal concentrations were inconsistent with farming cycles except for Cu, which increased in the order of 3.2±0.75, 4.4±0.66, and 4.8±1.23 mg/kg at 0–20 cm for R1, R2, and R3, respectively, and 3.4±0.66, 3.7±0.62, and 6.0±0.44 mg/kg at 20–40 cm in the same order. Pollution index values revealed that irrigation with TDW for three recurring farming cycles caused slight soil contamination (1≤PI<2) with Zn and Ni, moderate soil contamination (2≤PI<3) with Cu, and high soil contamination (3<PI) with Cr at depths of 0–20 and 40–60 cm. The pollution load index indicated moderate soil pollution (1<PLI≤2) with heavy metals after the R3 at 40–60 cm. The findings suggest that irrigation with TDW proceed for at least three recurring farming cycles without causing significant soil heavy metal accumulation.

Health and ecological risk assessment of heavy metals in water and sediments within a data scarce urban catchment in Tanzania – A case of Ngerengere River, Morogoro Municipality

Low-, middle- and high-income countries, exhibit indications of risks associated with water quality. The study investigated heavy metal concentrations in surface water and sediments within the Ngerengere River and its tributaries (Kikundi, Bigwa, and Morogoro) drain within in the Morogoro Municipality of Tanzania, an Urban Catchment Area (UCA) with limited available data mainly because of inadequate monitoring and reporting capabilities. Analysis of health and ecological risks associated with heavy metal pollution was also carried out using health risk assessments models, pollution indices, and multivariate analysis techniques. Between the dry and wet seasons of 2023, water and sediment samples from (13) sampling stations strategically established along the Ngerengere river and its tributaries were analyzed for six heavy metals (Pb, Cr, Ni, Cd, Cu and Zn) using the Atomic Absorption Spectrophotometer Model Perking Elmer 850 Graphite Furnace and Perking Elmer AS 800 Auto-sampler coupled with a computer interface for operational, displaying and reading the results. The calculated degree of water contamination (Cd) values in river water in both dry and wet seasons ranged from 0 to 6.803 indicating low and high degrees of contamination respectively. Heavy metal concentration in sediment decreases in the order of Zn&gt;Ni&gt;Cr&gt;Cu&gt;Cd&gt;Pb. The non-cancer risk index (HI) via ingestion and dermal pathways in dry and wet seasons for both children and adult groups was &lt;1 hence no non-cancer risk, However, cumulative dermal and ingestion exposure in both children and adults indicated potential cancer risk in dry and wet season. The analysis of ecological risks associated with heavy metal enrichment in the sediment indicated high enrichment of sediments with Cd, Ni and Zn. Conclusively, in wet months, risk indices tend to be low, while in dry months, they typically remain high.

Analysis of heavy metals in barley dust and health risk assessment in Malt Factory, Ethiopia

ABSTRACT The recent rapid industrialisation in Ethiopia has become a critical concern from pollution of the environment, including contamination by heavy metals. The purpose of this study was to determine heavy metals in barley dust and evaluate the health risks associated with workers in Gondar Malt Factory, Ethiopia. For this, the concentrations of some potentially toxic heavy metals (Cu, Ni, Cd, Cr, Pb, Zn and Fe) were determined in samples from four different production lines (barley receiving, aspiration, grading, and final product dispatch lines). Prior to metal analysis by flame atomic absorption spectroscopy, a 1 g barley dust was subjected to an optimised wet digestion procedure using 8 mL HNO3, 4 mL HClO4 heated for 4 h at 250°C. The average concentration (mg/kg) of the metals was found to be in the range of 3.3‒4.8 Cu, 4.7‒9 Cd, 9.5‒11.5 Pb, 3063‒3463 Fe, 17.7‒24.7 Ni and 148‒180 Zn. Chromium was below the detection limit of the method in all the samples. The results showed that the barley dust contained significant concentration of the heavy metals. However, the study has found the absence of non-carcinogenic risk, from the analysed heavy metals in the barley dust, through both dermal contact and inhalation routes of exposure. Similarly, no carcinogenic risk was associated with the analysed heavy metals in the barley dust, except for Pb. Hence, proper management control system needs to be implemented to minimise chronic health risks from exposure to Pb.

Geospatial evaluation and bio-remediation of heavy metal-contaminated soils in arid zones

Introduction: Soil pollution directly impacts food quality and the lives of both humans and animals. The concentration of heavy metals in Egypt’s drain-side soils is rising, which is detrimental to the quality of the soil and crops. The key to reducing the detrimental effects on the ecosystem is having accurate maps of the spatial distribution of heavy metals and the subsequent use of environmentally sustainable remediation approaches. The objective of this work is to assess soil contamination utilizing spatial mapping of heavy metals, determine contamination levels using Principal Component Analysis (PCA), and calculate both the contamination severity and the potential for bioremediation in the soils surrounding the main drain of Bahr El-Baqar. Furthermore, evaluating the capacity of microorganisms (bacteria, fungi, and “Actinomycetes) to degrade heavy elements in the soil.Methodology: 146 soil sample locations were randomly selected near the Bahr El-Baqar drain to examine the degree of soil pollution Ordinary Kriging (OK), method was used to map and analyze the spatial distribution of soil contamination by seven heavy metals (Cr, Fe, Zn, Cd, Pb, As, and Ni). Modified contamination degree (mCd) and PCA were used to assess the research area’s soil pollution levels. The process involved isolating, identifying, and classifying the microorganisms present in the soil of the study area. The study findings showed that variography suggested the Stable model effectively matched pH, SOM, and Cd values. Furthermore, the exponential model proved suitable for predicting Fe, Pb and Ni, while the spherical model was appropriate for Ni, Cr, and Zn.Results: The study revealed three levels of contamination, with an extremely high degree (EHDC) affecting approximately 97.49% of the area. The EHDC exhibited average concentrations of heavy metals: 79.23 ± 17.81 for Cr, 20,014.08 ± 4545.91 for Fe, 201.31 ± 112.97 for Zn, 1.33 ± 1.37 for Cd, 40.96 ± 26.36 for Pb, 211.47 ± 13.96 for As, and 46.15 ± 9.72 for Ni. Isolation and identification of microorganisms showed a significant influence on the breakdown of both organic and inorganic pollutants in the environment. The study demonstrated exceptionally high removal efficiency for As and Cr, with a removal efficiency reached 100%, achieved by Rhizopus oryzae, Pseudomonas aeruginosa, and Bacillus thuringiensis.Conclusion: This study has designated management zones for soil contamination by mapping soil pollutants, geo-identified them, and found potential microorganisms that could significantly reduce soil pollution levels.

Isotopic evidence of autochthonous organic matter acting as a major sink of anthropogenic heavy metals in modern lacustrine sediments

The knowledge of major sources, sinks, and the burial fate of various pollutants added to modern aquatic ecosystems under changing environmental conditions is limited but crucial for our sustainability. In this context, the spatial distributions and causative factors of organic matter (OM) and heavy metal accumulations have been explored in modern lacustrine sediments of a large urbanized and protected wetland (ULB: Upper Lake Bhopal) in Central India. For this purpose, geochemical properties, in particular, stable isotopes (δ13C and δ15N) were measured in the ULB surficial sediments (core depth ∼0–1 cm; n = 19), and additionally collected riverbed sediments (n = 2) and atmospheric free-fall dust samples (n = 3) from the lake periphery. The major and trace element data indicate widespread mafic sediment provenance and nearly dysoxic lacustrine conditions. The riverine supply of soil OM from cropped lands and the lake productivity (algae, largely sustained by nutrients from sewage and agricultural runoff) are the major OM sources to the western and eastern lake portions, respectively. The fractional contribution from autochthonous TOC (∼0.19–0.95, mean ∼0.62) predominates that of allochthonous TOC (∼0.05–0.81, mean ∼0.38). Whereas, atmospheric dust deposition is a primary anthropogenic source of heavy metals (Pb and Zn). The lake productivity rather than soil OM or any mineral sorbent is found responsible for the anthropogenic enrichments of Pb and Zn in the ULB surficial sediments, especially on the eastern ULB portion under high anthropogenic pressure. Therefore, the settled OM (primarily autochthonous) being oxidizable acts as a temporary but major sink of anthropogenic heavy metals in modern lacustrine sediments, which are vulnerable to heavy metal efflux to the water column by sediment diagenesis.

Thermodynamic analysis on the fate of ash elements in chemical looping combustion of solid fuels – Manganese-Based oxygen carriers

Chemical looping combustion (CLC) is an innovative technology suitable for converting waste-derived fuels into heat and power. The process inherently produces pure CO2, which is highly favorable for carbon capture and storage and could be instrumental for achieving negative emissions. CLC operates by utilizing solid oxygen carriers (OCs) to transfer heat and oxygen between two reactors. The OC play a crucial role in achieving an efficient combustion. Manganese-based OCs are particularly interesting, due to their ability to release gaseous oxygen. However, ash components from solid fuels could alter their oxygen transfer capacity, and cause problems related to corrosion and agglomeration. The objective of this work is to obtain in-depth insights about Mn-based OCs for CLC of waste-derived fuels. This is achieved by investigating phase transitions during CLC of solid fuels when utilizing two manganese-based OCs: manganese oxide and a representative manganese ore. For this purpose, thermodynamic modeling is employed, and a specific focus is given to K, Na, Cu, Zn, and Pb, due to their important role in corrosion and/or agglomeration. Thermodynamic databases are expanded by calculating properties from first-principles. It is shown that Mn-based OCs are suitable for effectively converting waste-derived fuels while limiting corrosion. Furthermore, the iron in manganese ores is found to have positive implications for oxygen-transfer reactions. In terms of alkali release to the gas phase, manganese ore seems to be a more promising material compared to manganese oxide. The pathways for the heavy metals Zn, Cu, and Pb were, meanwhile, independent of the OC type.

Risk Assessment and Sources Apportionment of Toxic Metals in Two Commonly Consumed Fishes from a Subtropical Estuarine Wetland System.

The widespread occurrence of heavy metals in aquatic environments, resulting in their bioaccumulation within aquatic organisms like fish, presents potential hazards to human health. This study investigates the concentrations of five toxic heavy metals (Pb, Hg, Zn, Cu, and Cr) and their potential health implications in two economically important fish species (Otolithoides pama and Labeo bata) from a subtropical estuarine wetland system (Feni estuary, Bangladesh). Muscle and gill samples from 36 individual fish were analyzed using energy dispersive X-ray fluorescence (EDXRF). The results revealed that the average quantities of heavy metals in both fishes' muscle followed the declining order of Zn (109.41-119.93 mg/kg) > Cu (45.52-65.43 mg/kg) > Hg (1.25-1.39 mg/kg) > Pb (0.68-1.12 mg/kg) > Cr (0.31-5.82 mg/kg). Furthermore, Zn was found to be present in the highest concentration within the gills of both species. While the levels of Cu, Zn, and Cr in the fish muscle were deemed acceptable for human consumption, the concentrations of Pb and Hg exceeded the permissible limits (>0.5 mg/kg) for human consumption. Different risk indices, including estimated daily intake (EDI), target hazard quotient (THQ), hazard index (HI), and carcinogenic or target risk (TR), revealed mixed and varying degrees of potential threat to human health. According to the EDI values, individuals consuming these fish may face health risks as the levels of Zn, Cu, and Cr in the muscle are either very close to or exceed the maximum tolerable daily intake (MTDI) threshold. Nevertheless, the THQ and HI values suggested that both species remained suitable for human consumption, as indicated by THQ (<1) and HI (<1) values. Carcinogenic risk values for Pb, Cr, and Zn all remained within permissible limits, with TR values falling below the range of (10-6 to 10-4), except for Zn, which exceeded it (>10-4). The correlation matrix and multivariate principal component analysis (PCA) findings revealed that Pb and Cr primarily stemmed from natural geological backgrounds, whereas Zn, Cu, and Hg were attributed to human-induced sources such as agricultural chemicals, silver nanoparticles, antimicrobial substances, and metallic plating. Given the significance of fish as a crucial and nutritious element of a balanced diet, it is essential to maintain consistent monitoring and regulation of the levels and origins of heavy metals found within it.

Occurrence, distribution, and ecological risk assessment of heavy metals in Chao Phraya River, Thailand

Understanding heavy metals in rivers is crucial, as their presence and distribution impact water quality, ecosystem health, and human well-being. This study examined the presence and levels of nine heavy metals (Cd, Cr, Cu, Fe, Hg, Mn, Ni, Pb, and Zn) in 16 surface water samples along the Chao Phraya River, identifying Fe, Mn, Zn, and Cr as predominant metals. Although average concentrations in both rainy and dry seasons generally adhered to WHO guidelines, Mn exceeded these limits yet remained within Thailand’s acceptable standards. Seasonal variations were observed in the Chao Phraya River, and Spearman’s correlation coefficient analysis established significant associations between season and concentrations of heavy metals. The water quality index (WQI) demonstrated varied water quality statuses at each sampling point along the Chao Phraya River, indicating poor conditions during the rainy season, further deteriorating to very poor conditions in the dry season. The hazard potential index (HPI) was employed to assess heavy metal contamination, revealing that during the dry season in the estuary area, the HPI value exceeded the critical threshold index, indicating the presence of heavy metal pollution in the water and unsuitable for consumption. Using the species sensitivity distribution model, an ecological risk assessment ranked the heavy metals’ HC5 values as Pb > Zn > Cr > Cu > Hg > Cd > Ni, identifying nickel as the most detrimental and lead as the least toxic. Despite Cr and Zn showing a moderate risk, and Cu and Ni posing a high risk to aquatic organisms, the main contributors to ecological risk were identified as Cu, Ni, and Zn, suggesting a significant potential ecological risk in the Chao Phraya River’s surface water. The results of this study provide fundamental insights that can direct future actions in preventing and managing heavy metal pollution in the river ecosystem.

Speciation, mobility, and risks of heavy metals in sediment and water of a freshwater Lake in Fujian Province, China

ABSTRACT This study investigated the level of dissolved heavy metals in the water of Longhu Lake and focused on the speciation, mobility, and risks of heavy metals (Cr, Mn, Ni, Cu, Zn, As, Cd, and Pb) in sediment. The levels of heavy metals in the water were found to be below the thresholds set by the Chinese safe drinking water standard. The highest average percentages of Cr, Ni, Zn, and As were bound with residual fractions, while Pb and Cu were bound with reducible fractions. Additionally, the highest percentage of Cd and Mn was bound to the acid-soluble fraction in the sediment. These findings suggest that Cd, Mn, Pb, and Cu likely originated from anthropogenic sources in the lake. There was a strong correlation between total organic carbon (TOC) and metal fractions in the sediment, indicating that TOC may play a role in transporting heavy metal fractions. Risk assessment code values for Cd and Mn indicated higher risks and mobility, while Ni, Cu, and Zn showed medium risks and mobility for aquatic biota. To mitigate heavy metal contamination, it is recommended to improve monitoring and regulation of urban runoff and inlet areas.