Changes In Hardness Research Articles

Study on the UV aging resistance of ZnO‐modified epoxy resin by experiments and MD simulation

AbstractThis study investigates the impact of zinc oxide nanoparticles on epoxy resin systems and the ultraviolet (UV) aging resistance of modified epoxy resin composites using molecular dynamics (MD) simulations and experimental methods. Initially, various epoxy resin cross‐linking models are established through MD simulations to understand the influence of different nano ZnO contents on resin modification, further validated by experiments. Subsequently, the UV radiation resistance of nano ZnO–epoxy resin composites is assessed by subjecting them to high‐intensity UV radiation equivalent to 3 years of natural environmental conditions, analyzing changes in tensile properties, impact performance, hardness, and glass transition temperature of epoxy resin before and after UV radiation exposure. The findings suggest that the addition of nano zinc oxide reduces the impact of UV radiation on epoxy resin, with optimal UV radiation resistance observed at a nano zinc oxide mass fraction of 0.3 wt%.

Evaluating the protective effects of mouthguards with neutralizing agents against chlorinated water-induced enamel erosion.

Dental erosion is a common problem among swimmers. This study evaluated the effects of mouthguard use with or without neutralizing agents, compared to no mouthguard use, on the microhardness of dental enamel after a swimming simulation. Ninety-six human premolars were randomly allocated into six groups of 16 each: Group A (no mouthguard), Group B (mouthguard only), Group C (mouthguard with fluoride toothpaste), Group D (mouthguard with fluoride-free toothpaste), Group E (mouthguard with CPP-ACP), and Group F (mouthguard with arginine-fluoride toothpaste). Enamel slabs were fixed in a wax model (Typodont Articulator) and used to fabricate mouthguards for all groups except Group A. Each specimen underwent cyclic immersion: 2 h in acidic chlorinated water (pH 3.1) followed by 22 h in artificial saliva, for 28 days, to simulate swimming exposure. The change in enamel surface hardness was measured using a Vickers hardness tester. All groups underwent microhardness testing, scanning electron microscopy, and polarized light microscopy. The enamel hardness significantly decreased in all groups after the swimming simulation (paired t-test, P-values < 0.001), except for Group F, which used a mouthguard with arginine-fluoride toothpaste [mean reduction: 17.9 kg/mm2, 95% confidence interval (CI): -1.9, 37.7, P-value = 0.07]. Group A, without a mouthguard, exhibited the highest reduction in enamel surface hardness (mean: 190.6 kg/mm2; 95%CI: 177.4, 203.9), significantly differing from all other groups with mouthguards (P-values < 0.001). However, no statistically significant differences were observed in enamel hardness reduction among the mouthguard groups. SEM micrographs illustrated rough, irregular erosion patterns and several deep porous areas on enamel surfaces of Group A. In contrast, all mouthguard groups showed enamel surfaces similar to sound tooth surfaces. A polarized light microscopic study revealed the deepest dark areas on the enamel surface of Group A. Mouthguards significantly reduced enamel microhardness loss compared to no mouthguard use. While no significant differences were found among mouthguard groups with or without neutralizing agents, those lined with arginine-fluoride toothpaste showed the least enamel loss, suggesting its potential protective effect. Within the limitations of this in vitro study, further clinical trials are needed to validate these results.

Clinical and Radiographic Evaluation of Soft Tissue and Bone Status in Immediate Loaded Implants Placed Following Their Extraction in the Maxillary Anterior Region.

In the maxillary anterior region, teeth extraction leads to significant soft and hard tissue changes. Immediate implant placement following extraction aims to reduce bone loss and overall treatment time. However, it may result in adverse soft tissue changes impacting esthetics. This study evaluates the clinical and radiographic outcomes of immediately loaded implants in the maxillary anterior region, focusing on soft tissue preservation and bone status. This study, conducted from April 2022 to August 2024 at the Department of Oral and Maxillofacial Surgery, Ragas Dental College and Hospital, included 10 immediately loaded implants in seven patients. Following atraumatic extraction, implants were placed and loaded with functional provisional crowns fabricated using three-dimensional (3D) rapid prototyping models. Parameters such as crestal bone loss, buccal and palatal bone width, and interdental papilla thickness were evaluated preoperatively and postoperatively using radiographsand clinical assessments. The study found significant crestal bone loss at both mesial and distal sites over time, with the greatest loss observed at the three-month follow-up. Buccal and palatal bone width showed no significant differences preoperatively and postoperatively. Interdental papilla thickness and overall pink esthetic scores also showed no significant differences between preoperative and postoperative evaluations. Immediate implant placement in the maxillary anterior region, using 3D rapid prototyping for custom splint fabrication, demonstrated effective preservation of soft tissue profile and bone architecture. This approach provides functional and esthetic benefits, although careful monitoring of crestal bone loss is necessary.

Mechanical and metallurgical properties of a glass fiber-reinforced Al7075 hybrid composite produced by infiltration and after aging and abrasion

Abstract Within the scope of this study, composite structures were produced by reinforcing Al7075 with 6 mm size glass fiber (GF) scrap at different weight rates (2–3 %) using the infiltration method. Mechanical and metallurgical examination of unreinforced Al7075 samples and reinforced Al7075 composite samples were carried out. After the aging heat treatment of the samples, pin-on-disc wear and hardness tests were performed. FESEM and EDS analyses were conducted to examine the hardness and microstructural changes caused by the applied processes on the samples. It was observed that GF reinforcement increased the hardness of the material and there was full wettability between Al 7075 and GF. Thus, wear resistance increased. The highest hardness and wear resistance were obtained in the 6 h aged 2 wt.% GF-reinforced Al 7075 matrix hybrid composite sample. In addition, it was observed that the distribution of GF scrap added as reinforcement at a rate of 2 wt.% in Al 7075 was homogeneous, and the hardness measurements taken from different areas were similar.

Postweld Heat Treatment of 15Cr-6Ni-2Mo-1Cu Supermartensitic Stainless Steel Welds

Supermartensitic stainless steels with 15Cr-6Ni- 2Mo-1Cu and 135 ksi minimum yield strength (15Cr- 135 SMSS) offer high strength and good toughness through a complex hierarchical microstructure of nanoscale precipitates, tempered martensite, and reverted austenite. Upon welding and postweld heat treatment, substantial changes to heat-affected zone microstructure and hardness may occur. Here, we reveal spatially heterogeneous microstructure and microhardness in the HAZ of 15Cr-135 SMSS; correlate these changes to measured phase transformation temperatures; and demonstrate that HAZ hardness changes depend strongly on postweld heat treatment (PWHT) temperatures. Furthermore, we demonstrate that PWHT may lead to undesired reductions in base metal yield strength and formulate a design guide for PWHT that quantifies the trade-offs in desired reductions of HAZ hardness with undesired changes to base metal yield strength. These findings have important practical implications for welding procedure design and qualification.

Service performance of nitrile rubber sealing ring under 70 MPa high-pressure hydrogen

Abstract The service performance of NBR seals under 70 MPa high-pressure hydrogen was investigated, and the effects of vulcanization additives, fillers, and crude systems on their sealing performance were investigated. The sealing performance was characterized by the changes in volume and hardness before and after the service of the seals.

The microhardness, morphology and tribological property of TC4 subjected to machine hammer peening

Ti alloy has become an indispensable material in harsh working environments due to its excellent wear resistance, corrosion resistance and impact resistance. These environments place stringent requirements on the fatigue life, friction and wear, and surface strength of materials. Therefore, this study aims to deeply explore the surface mechanical properties of Ti-6Al-4V (TC4) alloy after machine hammer peening (MHP) treatment. By conducting experiments on TC4 alloys treated with different hammering energies, the changes in surface hardness, morphology, roughness, tensile properties, and friction properties were analyzed, and the strengthening mechanism of MHP was discussed. Experimental results show that MHP treatment can effectively improve the surface properties of TC4. With the increase of hammer energy, due to the double-sided hammering of the plate, the microhardness first increases, then decreases, and then rises again. The tensile strength and yield strength of the sample increase slightly, but the elongation at break decreases. The surface roughness of the sample increases first and then decreases. Similarly, after MHP treatment, the wear resistance of the samples increased, the friction coefficient decreased, and the wear amount and surface height difference showed a trend of first increasing and then decreasing. The wear mechanism mainly included adhesive wear, abrasive wear and fatigue wear.

Effects of laser shock peening on silicon nitride ceramic with varying sintering additive ratios

Silicon nitride ceramic (Si3N4) for industrial applications is conventionally manufactured with sintering additives, and the properties of Si3N4 change significantly based on the contents of these additives. In this study, we investigate the effects of laser shock peening (LSP) on Si3N4 sintered with varying ratios of sintering additives.The Si3N4 samples were sintered with a mixture of Y2O3, MgO, and SiO2 sintering additives at 5, 7, 9, and 11 wt%. A Nd:YAG laser (wavelength = 532 nm, maximum pulse energy = 1.4 J, repetition rate = 10 Hz, pulse duration = 8 ns, beam diameter = 11 mm, top-hat profile) was used to irradiate the Si3N4 samples. The samples were coated with a protective layer (100 μm thick aluminum foil) and a water layer to confine plasma. LSP of Si3N4 with 5% sintering additives resulted in a slight change in surface hardness but a 77% decrease in surface compressive residual stress. In contrast, LSP of Si3N4 with 11% sintering additives led to a simultaneous increase in surface hardness (7.3%) and surface compressive residual stress (67%), indicating a significant difference in the effectiveness of LSP depending on the ratio of sintering additives. Additionally, the surface of Si3N4 with 11% sintering additives showed evidence of grain refinement after LSP. It was demonstrated that the bending strength of Si3N4 with 11% sintering additives increased by 15.2%, and the depth of the fracture origin was significantly deepened.

Electro-Mechanical Behavior of Copper-Based Electrical Motor Brushes

This study was mainly performed in order to examine the properties of electric motor brushes (EMB). EMBs are electrically conductive and work under wear conditions due to direct contact with the moving part (rotor) of electric motors. In accordance with the scope of the study, EMB characteristics were investigated in two different groups and reproduced with a new technique at the end of this phase. New EMBs were produced via varying proportions of copper matrix, graphene, and silicon carbide reinforcements. The composite-alloy powder elements were carefully squeezed by a cold and single-axis hydraulic press under a pressure of 500 MPa (±5 MPa) following 8 hours of mechanical alloying (MA). The molded composite product (sample) was sintered at 900° C for 1 hour in a reducing gas atmosphere. 100 kPa spring pressure was tested on each sample thrice with 8, 16, 24, and 32 m/s rotational speeds and densities of 4, 8, 12, and 16 A/cm2. Following this process, the electrical conductivity, porosity, hardness, wear loss, surface roughness, and temperature changes were investigated for each sample. It was determined that the electrical conductivity decreased with increasing reinforcement ratio and, in terms of electrical conductivity, affected the brushes’ properties negatively.

Influence of Mg Content on Microstructure Coarsening, Molten Pool Size, and Hardness of Laser Remelted Al(-x)-Mg-Sc Alloys.

Investigations leading to high-quality surfaces and optimized properties in laser remelted Al-Mg-Sc alloys remain scarce. Laser surface remelting (LSR) has been used for the final treatment of these alloys processed through additive manufacturing. However, the direct microstructure responses of the treated cast surfaces have not yet been investigated. In the present research, Al-3, 5, and 10 wt %-Mg-0.1 wt %-Sc alloys plates were processed using LSR to study the effects of local melting and rapid solidification. The morphology of the α-Al phase, microstructure coarsening, and hardness were mapped from the bottom to the top of the molten pools, varying with local Mg content and laser heat input (2.5 J/mm, 5 J/mm, and 10 J/mm). This study aimed to create a comprehensive map of the microstructures, hardness, and molten pool sizes under various conditions. The findings may help to optimize these alloys through understanding laser processing parameters. Methods used included CALPHAD computations, optical microscopy, SEM, EDS, image analysis, hardness tests, and heat flow models. The results obtained showed α-Al cell growth with bands in all alloys with hardness changes correlating with cell spacing and heat input. Higher Mg content resulted in more refined cells and a higher fraction of bands. Increased Mg content decreased the thermal diffusivity and enthalpy of melting, enlarging the molten pool size. Hardness increased with decreasing heat input and higher Mg content in the tested alloys, especially in the Al-10 wt %-Mg-0.1 wt %-Sc alloy as the heat input was varied.

Changes in Surface Topography and Light Load Hardness in Thrust Bearings as a Reason for Tribo-Electric Loads

The article focuses on the findings of endurance tests on thrust bearings. In addition to the mechanical load (axial load: 10 ≤ C0/P ≤ 19, lubrication gap: 0.33 µm ≤ h0 ≤ 1.23 µm), these bearings are also exposed to electrical loads (voltage: 20 Vpp ≤ U0 ≤ 60 Vpp, frequency 5 kHz and 20 kHz), such as those generated by modern frequency converters. In a previous study, the focus was on the chemical change in the lubricant and the resulting wear particles. In contrast, this article focuses on the changes occurring in the metallic contact partners. Therefore, the changes in the surface topography are analysed using Abbott–Firestone curves. These findings show that tests with an additional electrical load lead to a significant reduction in roughness peaks. A correlation to acceleration measurements is performed. Moreover, it is shown that the electrical load possibly has an effect on the light load hardness. An increase in the occurring wear could not be detected during the test series. Also, a comparison with mechanical reference tests is made. The article finally provides an overview of different measurement values and their sensitivity to additional electrical loads in roller bearings.

Surface quality enhancement in ultrasonic vibration-assisted electrochemical machining

The aviation industry's evolution has introduced electrochemical machining (ECM) as a promising non-traditional technology for aero-engine blades. However, the surface quality of challenging-to-cut materials is compromised due to insoluble electrolytic products on the machined surface. To enhance ECM's surface quality, ultrasonic-assisted ECM (UA-ECM) was introduced for effective electrolytic product removal. This study conducted numerical simulations involving coupled flow field and cavitation models. It also performed observation experiments and a series of UA-ECM trials with varying inlet pressures (0.1 MPa, 0.2 MPa, 0.3 MPa, 0.4 MPa, and 0.5 MPa), vibration amplitudes (21 µm, 17 µm, 13 µm, 8 µm, 4 µm, and 0 µm), and current densities (31.9 A/cm2, 42.1 A/cm2, 61.1 A/cm2, 76 A/cm2, and 100.9 A/cm2). These aimed to elucidate the mechanism of tool ultrasonic vibration's influence on surface quality and corroborate the simulation findings. Notably, under conditions of low inlet pressure (0.1 MPa), high vibration amplitude (21 µm), and high current density (100.9 A/cm2), complete removal of electrolytic products, inhibition of pitting defects, and attainment of a mirror surface with a surface roughness of Ra = 0.14 µm were achieved, with no change in hardness. This clearly demonstrates that the surface quality of ECM on complex surfaces can be significantly enhanced by ultrasonic assistance.

Hardness changing tactile displays for simulating the feel of organic tissues.

Physical interaction with patients, for example conducted as part of a diagnostic examination or surgical procedure, provides clinicians with a wealth of information about their condition. Simulating this interaction is of great interest to researchers in both haptics and medical education, and the development of softness changing tactile interfaces is important in recreating the feel of different soft tissues. This paper presents designs for a variety of novel electromechanical and electromagnetic mechanisms for controlling particle jamming-based, hardness changing tactile displays, intended to allow medical trainees to experience these physical interactions in a range of simulation settings such as clinical skills teaching laboratories. Each design is then subjected to a battery of mechanical tests to evaluate its effectiveness compared to the state of the art, as well as their suitability for simulating the physical hardness of different types of soft tissues, previously characterised in established literature. These results demonstrate that all of the technologies presented are able to exhibit a measurable hardness change, with Shore hardness values between 3A and 57A achieved by the most effective constriction-based device. The electromechanical devices based on constriction and compression, and the state-of-the-art pneumatic device, were able to achieve hardness changes within a range that is useful for replicating the softness of organic tissue. The electromechanical and electromagnetic devices were also found to effect their full range of hardness change in less than a second, compared to several seconds for the state-of-the-art. These results show that the performance of softness changing tactile displays can be improved with the electromechanical actuation techniques proposed in this paper, and that such displays are able to replicate the physical characteristics of soft tissues and may therefore be of benefit in medical training and simulation scenarios.

Effects of four types of packaging on the structural characteristics, quality attributes, and antioxidant activity of foxtail millet during storage

ABSTRACT The aim of this study is to select suitable packaging for extending the shelf-life of foxtail millet grains (FMG). FMG were packaged in four types of packaging and subsequently stored at room temperature (25°C ± 1°C) for 6 months. The effects of four types of packaging on the corresponding structural characteristics, quality attributes, and antioxidant activity of FMG were investigated. The results showed that aging led to less-prominent internal morphological changes with the vacuum- and N2-packaged samples. Moreover, vacuum and N2 packaging retarded the increase of fat acidity and the decrease of yellowness (b*) during storage. Aging in cotton and polyamide–polyethylene (PA/PE) packaging resulted in less soluble solids leakage during cooking, leading to more reduction in stickiness. No changes in hardness of cooked FMG were found only for vacuum packaging. In addition, total phenolic content and antioxidant capacities were well preserved under vacuum or N2 conditions. Overall, vacuum packaging was more effective in retarding the quality deterioration of FMG when compared to the other storage conditions.

The Influence of Cryogenic Treatment on the Tribological Properties of Tungsten Carbide

Improvement in wear resistance and hardness of cutting tool material is one of the most critical challenges in machining operations. This issue can be addressed by enhancing wear resistance and hardness through cryogenic treatment of tungsten carbide. This study investigates the effect of different soaking periods during cryogenic treatment on commercially available tungsten carbide. Experiments were conducted at a temperature of 88K with varying soaking periods of 8 hours, 20 hours, 24 hours, and 30 hours. To quantify and confirm the impact of different soaking periods on hardness and wear resistance, Rockwell hardness measurements and weight loss during wear tests were performed. The results indicate a significant decrease in weight loss for the sample soaked for 8 hours compared to other soaking periods, although there was no change in bulk hardness. The reduced weight loss during the sliding wear test suggests that cryogenically treated tungsten carbide exhibits improved wear resistance due to an increased population density of carbides. Microstructural analysis of the worn surface reveals the mechanism behind the enhanced mechanical properties. Key Words: Cryogenics, dct, sct, microstructure, soaking period, tool life.

The effects of beverage erosion on enamel: evaluating surface characteristics and loss of calcium and phosphate ions

BackgroundThe erosive impacts of various beverages on dental enamel have been identified as a potential erosive threat to dental hard tissues. This in vitro study aimed to address this by utilizing a systematic approach and advanced analytical methods to study enamel erosion due to selected beverages in a simulated oral environment.MethodsForty-nine extracted sound second premolar teeth were collected, disinfected, and prepared. These teeth were randomly allocated into seven groups, each exposed to a different beverage: distilled water, mineral water, instant coffee, black tea, Pepsi-Cola, orange juice, and synthetic vinegar. The modified Nordini Artificial Model (mNAM) was used to simulate the oral cavity. The enamel surfaces were scanned using a Scanning Electron Microscope (SEM) and analyzed using Energy-Dispersive X-ray Spectroscopy (EDS). Surface hardness was measured using the Knoop Hardness Scale. Statistical analysis was conducted using the Wilcoxon signed-rank test, with a significance level set at p < 0.05.ResultsDistilled water and mineral water exhibited no significant changes in enamel surface or hardness. Coffee caused an 8–9% loss of calcium and phosphate, indicating potential erosion. Black tea showed signs of remineralization rather than demineralization. Pepsi-Cola and orange juice caused substantial erosion, with Pepsi-Cola resulting in a nearly 24% loss of calcium. Vinegar had a marked erosive effect, with a 17% loss of both calcium and phosphate. SEM images corroborated these findings, showing pronounced enamel prisms and increased visibility of minor cracks in post-treatment teeth. EDS analysis revealed significant changes in the elemental composition of the enamel.ConclusionsThis study categorised beverages based on their pH and fluoride content, revealing that drinks like Pepsi-Cola and orange juice are acidic but low in fluoride, whereas black tea, mineral water, and vinegar are acidic yet contain fluoride. The study suggests that the decrease in pH of acidic beverages may contribute to dental erosion, with fluoride as a mitigating factor. Among the various metrics assessed for evaluating dental erosion, hardness emerged as the most reliable quantitative parameter.

The effects of heat treatment on the mechanical properties of 450 HB wear resistant steel

The effects of heat treatment on the mechanical properties of 450 HB wear resistant steel produced by Usiminas steelworks in the form of heavy plates were investigated. The results showed that when tempering temperature is lower than 200°C, there are no significant changes in hardness, tensile properties and absorbed energy in Charpy V-notch test. With further increase in temperature up to 400°C, hardness, tensile strength, total elongation and impact toughness exhibited a slight downward trend. For heating carried out from 400°C to 600°C, a very significant drop in hardness and tensile strength and an increase in total elongation and absorbed energy values were observed. The abrasive wear resistance, evaluated by dry-sand rubber wheel test, increased with the heating up to 500°C. With the additional rise in temperature to 600°C, the abrasive wear resistance decreased, reaching a similar level to the reference state (steel in as-delivered condition).

Surface Characteristics and Artificial Weathering Resistance of Oil-Based Coatings on the Chemically and Thermally Modified Short-Rotation Teak Wood.

Improving the durability of short-rotation wood can be achieved through chemical and thermal modification. Chemical and thermal modification can have an impact on the physicochemical properties of wood, which can affect wood's surface characteristics and its resistance to weathering. The purpose of this study was to investigate the surface characteristics and artificial weathering resistance of chemically and thermally modified short-rotation teak wood coated with linseed oil (LO)-, tung oil (TO)-, and commercial oil-based coatings consisting of a mixture of linseed oil and tung oil (LT) and commercial oil-based polyurethane resin (LB) coatings. The short-rotation teak woods were prepared in untreated and treated with furfuryl alcohol (FA), thermal treatment (HT) at 150 and 220 °C, and combination of glycerol-maleic anhydride (GMA) impregnation with thermal treatment at 150 and 220 °C. The surface characteristics measured were surface free energy, wettability, Persoz hardness, bonding quality, and color changes before and after artificial weathering exposure. The results showed that chemical and thermal modifications treatment tended to reduce total surface free energy (SFE), hardness, wettability, and bonding quality. FA and GMA at 220 °C treatments provided homogenization effect on surface characteristics, especially in total SFE and wettability. The total SFE of untreated wood ranged from 45.00 to 51.13 mN/m, and treated wood ranged from 40.58 to 50.79 mN/m. The wettability of oil-based coating according to K-value ranged from 0.20 to 0.54. TO presented better photostability than LO. Short-rotation teak wood coated with oil-based commercial coatings presented better weathering resistance compared to pure natural drying oil. Commercial oil-based coatings provided better weathering protection for the chemically and thermally modified teak wood. The application of oil-based coatings on chemically and thermally modified short-rotation teak is being considered for the development of a better wood-protection system.

Examination of Surface Hardness and Roughness of AISI 1050 Steel Material in Milling Based on Surface Processing Conditions

It is known that material hardness and surface conditions have a significant impact on the operating life of machine elements working with each other. In this study, Surface roughness values obtained depending on processing conditions and hardness changes on the machined surfaces during milling of AISI 1050 steel were examined. In experimental studies, ideal machining conditions were determined by taking into account surface roughness values and hardness changes using the Taguchi L18 experimental design method. In all experiments, it was observed that the lowest surface hardness was achieved under dry conditions when 6500 1/min speed, 4000 mm/min feed rate, and 0.4 mm cutting depth values were applied. When the speed increased from 5500 1/min to 6000 1/min and the feed rate increased from 4500 mm/min to 5000 mm/min, improvements in surface quality were observed in both machining conditions. In conclusion; In experiments where coolant was applied at high cutting speeds, it was determined that surface hardness and surface roughness values were higher than in dry machining conditions.

Encapsulation of Peperomia pellucida (L.) kunth leaf extract for postharvest preservation of Malang apple (Malus sylvestris) at ambient storage

This study investigated the efficacy of edible coatings based on encapsulated Peperomia pellucida leaf extract to extend the shelf life of Malang apples. An edible coating was developed by encapsulating P. pellucida leaf extract using a chitosan-STPP matrix. The optimum encapsulation efficiency observed of polyphenols and flavonoids retention was 86.25% ± 0.02 and 83.30% ± 0.04, respectively. It achieved by 2.5% chitosan, 2% STPP, and 3.5% extract in formula. The encapsulated extract was further applied to Malang apples as edible coated using varying dipping times and stored for 15 days at ambient temperature. Evaluation parameters on coated Malang apples included hardness, weight loss, pH, moisture content, and color change. A 1-min dipping time of the encapsulated extract was found to be optimal, effectively reducing physical and chemical alterations and enhancing the shelf-life quality of the apples. Therefore, the edible coating derived from encapsulated P. pellucida leaf extract presents a promising alternative for preserving Malang apples.