Gravimetric Sensors Research Articles

Microfluidic QCM enables ultrahigh Q-factor: a new paradigm for in-liquid gravimetric sensing

Acoustic gravimetric biosensors attract attention due to their simplicity, robustness, and low cost. However, a prevailing challenge in these sensors is dissipation which manifests in a low quality factor (Q-factor), which limits their sensitivity and accuracy. To mitigate dissipation of acoustic sensors in liquid environments we introduce an innovative approach in which we combine microfluidic channels with gravimetric sensors. To implement this novel paradigm we chose the quartz crystal microbalance (QCM) as our model system, owing to its wide applicability in biosensing and the relevance of its operating principles to other types of acoustic sensors. We postulate that the crucial determinant for enhancing performance lies in the ratio between the width of the microfluidic channels and the wavelength of the pressure wave generated by the oscillating channel side walls driven by the QCM. Our hypothesis is supported by finite element analysis (FEA) and dimensional studies, which revealed two key factors that affect device performance: (1) the ratio of the channel width to the pressure wavelength (W/λp\\documentclass[12pt]{minimal} \\usepackage{amsmath} \\usepackage{wasysym} \\usepackage{amsfonts} \\usepackage{amssymb} \\usepackage{amsbsy} \\usepackage{mathrsfs} \\usepackage{upgreek} \\setlength{\\oddsidemargin}{-69pt} \\begin{document}$$W/{\\lambda }_{{\\rm {p}}}$$\\end{document}) and (2) the ratio of the channel height to the shear evanescent wavelength (H/λs\\documentclass[12pt]{minimal} \\usepackage{amsmath} \\usepackage{wasysym} \\usepackage{amsfonts} \\usepackage{amssymb} \\usepackage{amsbsy} \\usepackage{mathrsfs} \\usepackage{upgreek} \\setlength{\\oddsidemargin}{-69pt} \\begin{document}$$H/{\\lambda }_{{\\rm {s}}}$$\\end{document}). To validate our hypothesis, we fabricated a microfluidic QCM (µ-QCM) and demonstrated a remarkable 10-fold improvement in its dissipation when compared to conventional QCM. The novel microfluidic approach offers several additional advantages, such as direct data interpretation, reduced volume requirement for sample liquids, and simplified temperature control, augmenting the sensor’s overall performance. By fostering increased sensitivity, accuracy, and ease of operation, our novel paradigm unlocks new possibilities for advancing gravimetric technologies, potentially for biosensing applications.

Design of Zeolitic Imidazolate Framework-8-Functionalized Capacitive Micromachined Ultrasound Transducer Gravimetric Sensors for Gas and Hydrocarbon Vapor Detection

A capacitive micromachined ultrasound transducer (CMUT) was engineered and functionalized with zeolitic imidazolate framework-8 (ZIF-8) dispersed in a photoresist AZ1512HS (AZ) matrix to function as a gravimetric gas sensor. The sensor response was recorded in the presence of nitrogen, argon, carbon dioxide, and methane gases as well as water, acetylene, a propane/butane mixture, n-hexane, gasoline, and diesel vapors. The photoresist matrix alone was found to have a negligible response to all the gases and vapors, except for water vapor. No visible difference in sensor response was detected when switching from nitrogen to methane gas. However, a strong shift in the sensor resonance frequency was observed when exposed to higher hydrocarbons, ranging from 1 kHz for acetylene to 7.5 kHz for gasoline. Even longer-chain hydrocarbons, specifically kerosene and more so diesel, had a significantly reduced sensor frequency shift compared with gasoline. Sensors functionalized with a thin film of AZ+ZIF-8 demonstrated higher sensitivity in their response to a hydrocarbon molecular mass than without functionalization.

High-Temperature Piezoelectric Resonators: Electroacoustic Properties and Applications of Langasite-Type Crystals

Piezoelectric devices based on high-temperature stable single crystals are of increasing interest due to a wide range of potential applications, such as actuators and resonant gravimetric sensors. The latter require highly accurate resonant-frequency measurements at temperatures as high as 1000 °C, and this can only be achieved with narrow resonance peaks and correspondingly low acoustic loss at these temperatures. Relevant atomistic defects in langasite (La3Ga5SiO14, LGS) and catangasite (Ca3TaGa3Si2O14, CTGS) are reviewed with respect to their impact on electrical conductivity and acoustic loss. The focus on these crystals also enables a comparison of electroacoustic properties of partially disordered (LGS) and ordered (CTGS) crystals and the formulation of approaches for reducing acoustic loss and enhancing device performance.Starting with defect chemistry models for LGS and CTGS, electrical conductivities as a function of temperature and oxygen partial pressure are considered. One result of this analysis is that contributions of oxygen ions to the total conductivity are determined to be relatively small in the studied crystals. Temperature-dependent acoustic loss of LGS and CTGS crystals is also studied. Two independent techniques, contact resonant piezoelectric spectroscopy, and a contactless tone-burst excitation technique, are applied. Contributions to the measured acoustic loss are determined by fitting loss-related functions for point defects and conductivity-related relaxations. The extracted fit parameters, in particular the activation energies of the processes, are discussed and compared with that of the electrical conductivity. The losses are caused by a superposition of several mechanisms including conductivity-related relaxations, point-defect relaxations and intrinsic phonon-phonon loss.The long-term stability of the crystals is also evaluated at 1000 °C with respect to fundamental materials properties including electrical conductivity and resonant frequency.After one year of thermal treatment, the resonance frequency of CTGS resonators from different crystal sources is found to decrease by no more than 0.4 %. Thus, the applicability of CTGS as a piezoelectric resonator that operates for long periods at extreme temperatures, such as a resonant nanobalance, is demonstrated.Application examples to be presented include resonant nanobalances for in-situ monitoring of non-stoichiometry and phase transformations in thin films during growth at high temperatures. In this context, the key application properties of the sensors at high temperatures, such as mass sensitivity and resolution, are discussed. As an application example, the attached figure shows the oxygen non-stoichiometry x of thin praseodymium-cerium oxide films (Pr0.1Ce0.9O2-x) at 700 °C as a function of oxygen partial pressure determined by LGS and CTGS nanobalances, which agrees very well with literature data (chemical capacitance: D. Chen et al., Chem. Mater. 2014, 26, 22, 6622–6627). Figure 1

Highly selective capacitive micromachined ultrasonic transducer–based miniature gravimetric CO2 sensor with in-situ calibration for relative humidity

The prototype gravimetric microelectromechanical imine functionalized CO2 sensor equipped with custom electronics and significantly increased stability under sub-percent concentrations is investigated. Instabilities caused by the relative air humidity were eliminated by two in-situ calibration methods: two-channel readings correction and single-channel correction by the reference disturbance. Capacitive micromachined ultrasound transducers (CMUT) were designed for 15 MHz nominal resonance frequency, while actual sensor readings were lower (over 12 MHz) due to the functionalization. The resonance frequency of polyethyleneimine (PEI) functionalized CMUT during sub-percent CO2 detection experienced instabilities of several hundred Hz while the relative humidity of the air was changed between 10% and 35%. Readings of graphene oxide (GOx) functionalized CMUT working in parallel with PEI functionalized CMUT were used for two-channel correction, resulting in highly stable sensor output, characterized by 3.2 Hz standard deviation during almost one hour experiment, while relative humidity varied between 10% and 25%. Single channel reading correction method resulted in larger residual instability, characterized by a standard deviation of up to 36 Hz over a two-hour experiment, however, it was found to be more effective for longer humidity-induced drifts, since reference disturbance of known relative humidity of 75% maintained by saturated NaCl solution technique was used.

Chiral Recognition by Supramolecular Porphyrin–Hemicucurbit[8]uril-Functionalized Gravimetric Sensors

Enantiorecognition of a chiral analyte usually requires the ability to respond with high specificity to one of the two enantiomers of a chiral compound. However, in most cases, chiral sensors have chemical sensitivity toward both enantiomers, showing differences only in the intensity of responses. Furthermore, specific chiral receptors are obtained with high synthetic efforts and have limited structural versatility. These facts hinder the implementation of chiral sensors in many potential applications. Here, we utilize the presence of both enantiomers of each receptor to introduce a novel normalization that allows the enantio-recognition of compounds even when single sensors are not specific for one enantiomer of a target analyte. For this purpose, a novel protocol that permits the fabrication of a large set of enantiomeric receptor pairs with low synthetic efforts by combining metalloporphyrins with (R,R)- and (S,S)-cyclohexanohemicucurbit[8]uril is developed. The potentialities of this approach are investigated by an array of four pairs of enantiomeric sensors fabricated using quartz microbalances since gravimetric sensors are intrinsically non-selective toward the mechanism of interaction of analytes and receptors. Albeit the weak enantioselectivity of single sensors toward limonene and 1-phenylethylamine, the normalization allows the correct identification of these enantiomers in the vapor phase indifferent to their concentration. Remarkably, the achiral metalloporphyrin choice influences the enantioselective properties, opening the way to easily obtain a large library of chiral receptors that can be implemented in actual sensor arrays. These enantioselective electronic noses and tongues may have a potential striking impact in many medical, agrochemical, and environmental fields.

Mesoporous-Structure MOF-14-Based QCM p-Xylene Gas Sensor.

In this work, a facile synthesis method was adopted to synthesize MOF-14 with mesoporous structure. The physical properties of the samples were characterized by PXRD, FESEM, TEM and FT-IR spectrometry. By coating the mesoporous-structure MOF-14 on the surface of a quartz crystal microbalance (QCM), the fabricated gravimetric sensor exhibits high sensitivity to p-toluene vapor even at trace levels. Additionally, the limit of detection (LOD) of the sensor obtained experimentally is lower than 100 ppb, and the theoretical detection limit is 57 ppb. Furthermore, good gas selectivity and fast response (15 s) and recovery (20 s) abilities are also illustrated along with high sensitivity. These sensing data indicate the excellent performance of the fabricated mesoporous-structure MOF-14-based p-xylene QCM sensor. On the basis of temperature-varying experiments, an adsorption enthalpy of -59.88 kJ/mol was obtained, implying the existence of moderate and reversible chemisorption between MOF-14 and p-xylene molecules. This is the crucial factor that endows MOF-14 with exceptional p-xylene-sensing abilities. This work has proved that MOF materials such as MOF-14 are promising in gravimetric-type gas-sensing applications and worthy of future study.

Synthesis and Characterization of New-Type Soluble β-Substituted Zinc Phthalocyanine Derivative of Clofoctol.

In this work, we have described the synthesis and characterization of novel zinc (II) phthalocyanine bearing four 2-(2,4-dichloro-benzyl)-4-(1,1,3,3-tetramethyl-butyl)-phenoxy substituents on the peripheral positions. The compound was characterized by elemental analysis and different spectroscopic techniques, such as FT-IR, 1H NMR, MALDI-TOF, and UV-Vis. The Zn (II) phthalocyanine shows excellent solubility in organic solvents such as dichloromethane (DCM), n-hexane, chloroform, tetrahydrofuran (THF), and toluene. Photochemical and electrochemical characterizations of the complex were performed by UV-Vis, fluorescence spectroscopy, and cyclic voltammetry. Its good solubility allows a direct deposition of this compound as film, which has been tested as a solid-state sensing material in gravimetric chemical sensors for gas detection, and the obtained results indicate its potential for qualitative discrimination and quantitative assessment of various volatile organic compounds, among them methanol, n-hexane, triethylamine (TEA), toluene and DCM, in a wide concentration range.

Ag-ZnS Embedded Polymeric Receptors for the Recognition of Human Serum Albumin

The detection of human serum albumin (HSA) is of significant clinical importance in disease diagnoses. In this work, polymer-based synthetic receptors are designed by incorporating Ag-ZnS microspheres in molecularly imprinted poly(methacrylic acid-co-ethylene glycol dimethacrylate) (MIPs) for the gravimetric detection of HSA. Among different compositions of Ag-ZnS@MIPs, MIPs having methacrylic acid and ethylene glycol dimethacrylate volume ratio of 3:2 exhibit enhanced HSA sensitivity in the concentration range of 5–200 ng/mL. A remarkably low threshold limit of detection (LOD = 0.364 ng/mL) is achieved with quartz crystal microbalance (QCM) based gravimetric sensors. Furthermore, the Ag-ZnS@MIPs/QCM sensors show high selectivity for HSA compared to other proteins, e.g., bovine serum albumin (BSA), glycoprotein, ribonuclease, and lysozyme. Hence, the gravimetric quantification of HSA realizes a highly sensitive, selective, and label-free detection mechanism with a limit of quantification down to 1.1 ng/mL.

Design and Fabrication of a Flexible Gravimetric Sensor Based on a Thin-Film Bulk Acoustic Wave Resonator.

Sensing systems are becoming less and less invasive. In this context, flexible materials offer new opportunities that are impossible to achieve with bulky and rigid chips. Standard silicon sensors cannot be adapted to curved shapes and are susceptible to big deformations, thus discouraging their use in wearable applications. Another step forward toward minimising the impacts of the sensors can be to avoid the use of cables and connectors by exploiting wireless transmissions at ultra-high frequencies (UHFs). Thin-film bulk acoustic wave resonators (FBARs) represent the most promising choice among all of the piezoelectric microelectromechanical system (MEMS) resonators for the climbing of radio frequencies. Accordingly, the fabrication of FBARs on flexible and wearable substrates represents a strategic step toward obtaining a new generation of highly sensitive wireless sensors. In this work, we propose the design and fabrication of a flexible gravimetric sensor based on an FBAR on a polymeric substrate. The resonator presents one of the highest electromechanical coupling factors in the category of flexible AlN-based FBARs, equal to 6%. Moreover, thanks to the polymeric support layer, the presence of membranes can be avoided, which leads to a faster and cheaper fabrication process and higher robustness of the structure. The mass sensitivity of the device was evaluated, obtaining a promising value of 23.31 ppm/pg. We strongly believe that these results can pave the way to a new class of wearable MEMS sensors that exploit ultra-high-frequency (UHF) transmissions.

Motor variability during a repetitive lifting task is impaired by wearing a passive back-support exoskeleton.

Evaluate whether wearing a passive back-support exoskeleton during repetitive lifting impairs motor variability of erector spinae muscle and spine movement and whether this association is influenced by lifting style. Thirty-six healthy males performed ten lifts in four randomized conditions with exoskeleton (without, with) and lifting style (squat, stoop) as dependent variables. One lifting cycle contained four phases: bending/straighten without/with load. Erector spinae muscular activity, thoracic kyphosis and lumbar lordosis were measured with surface electromyography and gravimetric position sensors, respectively. Absolute and relative cycle-to-cycle variability were calculated. The effects of exoskeleton and exoskeleton×lifting style were assessed on outcomes during the complete lifting cycle and its four phases. For the complete lifting cycle, muscular variability and thoracic kyphosis variability decreased whereas lumbar lordosis variability increased with exoskeleton. For lifting phases, effects of exoskeleton were mixed. Absolute and relative muscular variability showed a significant interaction effect for the phase straighten with load; variability decreased with exoskeleton during squat lifting. Using the exoskeleton impaired several motor variability parameters during lifting, supporting previous findings that exoskeletons may limit freedom of movement. The impact of this result on longer-term development of muscular fatigue or musculoskeletal disorders cannot yet be estimated.

Experimental research of electrical characteristics combined solar-electric air heater

Poor water quality in district heating systems leads to failure of boilers and pipelines in heating networks. The main reason for this is corrosion and scale deposits. The presence of these factors shows the low efficiency of water treatment systems. The article presents the results of the introduction of non-traditional water treatment technologies for district heating systems based on the experience of the Zhytomyrteplokommunenergo utility company of the Zhytomyr City Council in 2007-2021. In the boiler houses of the enterprise, water treatment systems were modernized, and the production chemical service was reorganized. In particular, chemical deaeration was launched in combination with traditional sodium cationization, as well as chemical deaeration in combination with complexonate water treatment against the classical water treatment technology - ion exchange. Installed magnetic sludge separators with magnetic inserts. The technology of water softening with anti-corrosion protection using Redox filters has been introduced. Gravimetric corrosion sensors of our own design have been developed and installed. The database of processing and statistical analysis Access "Corrosion damage of pipelines of heat networks" was created and put into operation. The experience of modernizing the water treatment system has shown that work in this direction increases the reliability of operation of district heating systems by reducing the consumption of energy carriers and material resources. In addition, the problem of improving the operational reliability of the heat exchange equipment of thermal stations needs to be solved. The projected start of the use of heat recovery devices on water heating boilers in operation, in condensation or partially condensation modes, will also bring with it a number of problems with the neutralization of condensate and its return to the heat supply system. The end result is an increase in production reliability, environmental friendliness and a reduction in the cost of heat for district heating systems.

Molecularly Designed Ion-Imprinted Nanoparticles for Real-Time Sensing of Cu(II) Ions Using Quartz Crystal Microbalance.

A molecularly designed imprinting method was combined with a gravimetric nanosensor for the real-time detection Cu(II) ions in aqueous solutions without using expensive laboratory devices. Thus, 1:1 and 2:1 mol-ratio-dependent coordination modes between Cu(II), N-methacyloly-L histidine methyl ester (MAH) functional monomer complexes, and their four-fold and six-fold coordinations were calculated by means of density functional theory molecular modeling. Cu(II)-MIP1 and Cu(II)-MIP2 nanoparticles were synthesized in the size range of 80-100 nm and characterized by SEM, AFM and FTIR. Cu(II)-MIP nanoparticles were then conducted to a quartz crystal microbalance sensor for the real-time detection of Cu(II) ions in aqueous solutions. The effects of initial Cu(II) concentration, selectivity, and imprinting efficiency were investigated for the optimization of the nanosensor. Linearity of 99% was obtained in the Cu(II) ion linear concentration range of 0.15-1.57 µM with high sensitivity. The LOD was obtained as 40.7 nM for Cu(II)-MIP2 nanoparticles. The selectivity and the imprinting efficiency of the QCM nanosensor were obtained significantly in the presence of competitive ion samples (Co(II), Ni(II), Zn(II), and Fe(II)). The results are promising for sensing Cu(II) ions as environmental toxicants in water by combining molecularly designed ion-imprinted nanoparticles and a gravimetric sensor.

Comparative Study of Gravimetric Humidity Sensor Platforms Based on CMUT and QCM.

Humidity sensors with comprehensive performance are of great interest for industrial and environmental applications. Most sensors, however, have to compromise on at least one characteristic such as sensitivity, response speed, and linearity. This paper reports a gravimetric humidity sensor based on a capacitive micromachined ultrasonic transducer (CMUT) with exceptional all-around performance, and presents a side-by-side comparative investigation of two types of gravimetric humidity sensors for a better understanding of their characteristics and sensing mechanisms. For these purposes, a circular CMUT and a quartz crystal microbalance (QCM) with a resonance frequency of 10 MHz were designed and fabricated. Poly(vinyl alcohol) (PVA) was employed as the humidity sensing layer for its hydrophilicity and ease of film formation. The electrical properties of the sensors, including the electrical input impedances and quality factors, were characterized by a vector network analyzer. The relative humidity (RH) sensing performance of the sensors was evaluated and compared from RH levels of 11% to 97%. Both sensors exhibited good repeatability and low hysteresis. The unique microscale resonant structure of the CMUT humidity sensor contributed to a high sensitivity of 2.01 kHz/%RH, short response and recovery times of 8 s and 3 s, respectively, and excellent linearity (R2 = 0.973), which were far superior to their QCM counterparts. The underlying mechanism was revealed and discussed.

Evaluation of Green-Synthesized Cuprospinel Nanoparticles as a Nanosensor for Detection of Low-Concentration Cd(II) Ion in the Aqueous Solutions by the Quartz Crystal Microbalance Method.

Cd(II) heavy metal is an extremely dangerous hazardous material for both humans and the environment. Its high toxicity is the reason behind the examination of new techniques for detecting very small concentrations of Cd(II). Recently, Quartz Crystal Microbalance (QCM) has been one of the techniques that have been widely used to detect trace heavy metal ions in solutions. It is a simple, inexpensive, portable, and sensitive gravimetric sensor due to its quality sensitivity lowest to nanograms. In this work, Cuprospinel nanoparticles were synthesized through the green synthesis approach using Psidium guajava L. leaf extract as a reducing agent, which is the first scientific description to report the preparation of these nanoparticles by this method. Subsequently, the synthesized nanoparticles were subjected to the characterization of their crystallinity, structure, and morphology by the XRD, N2 adsorption–desorption, zeta potential, DLS, AFM, SEM, and TEM analyzers. The prepared Cuprospinel nanoparticles were evaluated as a nanosensor for the detection of the very low concentration of Cd(II) ions in aqueous solutions using the QCM technique. The results of the characterization proved that the Cuprospinel nanoparticles have formed in the nanoscale with sub-spherical shapes and particles size ranging from 20 to 80 nm. The BET surface area and pore size analysis revealed that the synthesized Cuprospinel nanoparticles possess a surface area of 47.3 m2/g, an average pore size of 1.5 nm, and a micropore volume of 0.064 cc/g. The QCM results demonstrated the success of the Cuprospinel nanoparticles sensor in detecting the tiny amounts of Cd(II) ions in the aqueous solutions with concentrations reaching about 3.6 ng/L.

Effects of a Passive Back-Support Exoskeleton on Knee Joint Loading during Simulated Static Sorting and Dynamic Lifting Tasks.

Due to the load shifting mechanism of many back-support exoskeletons (BSEs), this study evaluated possible side effects of using a BSE on knee joint loading. Twenty-nine subjects (25.9 (±4.4) years, 179.0 (±6.5) cm; 73.6 (±9.4) kg) performed simulated static sorting and dynamic lifting tasks, including stoop and squat styles and different trunk rotation postures. Ground reaction force, body posture and the force between the chest and the BSE’s contact interface were recorded using a force plate, two-dimensional gravimetric position sensors, and a built-in force sensor of the BSE, respectively. Using these parameters and the subject’s anthropometry, median and 90th percentile horizontal (HOR50, HOR90) and vertical (VERT50, VERT90) tibiofemoral forces were calculated via a self-developed inverse quasi-static biomechanical model. BSE use had a variable effect on HOR50 dependent on the working task and body posture. Generally, VERT50 increased without significant interaction effects with posture or task. HOR90 and VERT90 were not affected by using the BSE. In conclusion, utilizing the investigated exoskeleton is likely to induce side effects in terms of changed knee joint loading. This may depend on the applied working task and the user’s body posture. The role of these changes in the context of a negative contribution to work-related cumulative knee exposures should be addressed by future research.

Sensors for Volatile Organic Compounds.

This paper provides an overview of recent developments in the field of volatile organic compound (VOC) sensors, which are finding uses in healthcare, safety, environmental monitoring, food and agriculture, oil industry, and other fields. It starts by briefly explaining the basics of VOC sensing and reviewing the currently available and quickly progressing VOC sensing approaches. It then discusses the main trends in materials' design with special attention to nanostructuring and nanohybridization. Emerging sensing materials and strategies are highlighted and their involvement in the different types of sensing technologies is discussed, including optical, electrical, and gravimetric sensors. The review also provides detailed discussions about the main limitations of the field and offers potential solutions. The status of the field and suggestions of promising directions for future development are summarized.

Recent Sensing Technologies of Imperceptible Water in Atmosphere

Accurate detection and quantitative evaluation of environmental water in vapor and liquids state expressed as humidity and precipitation play key roles in industrial and scientific applications. However, the development of supporting tools and techniques remains a challenge. Although optical methods such as IR and LASER could detect environmental water in the air, their apparatus is relatively huge. Alternatively, solid detection field systems (SDFSs) could recently lead to a revolution in device downsizing and sensing abilities via advanced research, mainly for materials technology. Herein, we present an overview of several SDFS based sensing categories and their core materials mainly used to detect water in atmosphere, either in the vapor or liquid phase. We considered the governing mechanism in the detection process, such as adsorption/desorption, condensation/evaporation for the vapor phase, and surface attach/detach for the liquid phase. Sensing categories such as optical, chilled mirror, resistive, capacitive, gravimetric sensors were reviewed together with their designated tools such as acoustic wave, quartz crystal microbalance, IDT, and many others, giving typical examples of daily based real scientific applications.

Using a Passive Back Exoskeleton During a Simulated Sorting Task: Influence on Muscle Activity, Posture, and Heart Rate.

To evaluate using a back exoskeleton in a simulated sorting task in a static forward bent trunk posture on muscle activity, posture, and heart rate (HR). Potentials of exoskeletons for reducing musculoskeletal demands in work tasks need to be clarified. Thirty-six healthy males performed the sorting task in 40°-forward bent static trunk posture for 90seconds, in three trunk orientations, with and without exoskeleton. Muscle activity of the erector spinae (ES), biceps femoris (BF), trapezius descendens (TD), rectus abdominis (RA), vastus laterals (VL), and gastrocnemius medialis was recorded using surface electromyography normalized to a submaximal or maximal reference electrical activity (%RVE (reference voluntary electrical activity)/%MVE). Spine and lower limb postures were assessed by gravimetric position sensors, and HR by electrocardiography. Using the exoskeleton resulted in decreased BF muscle activity [-8.12%RVE], and minor changes in ES [-1.29%MVE], RA [-0.28%RVE], VL [-0.49%RVE], and TD [+1.13%RVE] muscle activity. Hip and knee flexion increased [+8.1°; +6.7°]. Heart rate decreased by 2.1 bpm. Trunk orientation had an influence on BF muscle activity. Using the back exoskeleton in a short sorting task with static trunk posture mainly reduced hip extensor muscle activity and changed lower limb but not spine posture. Implications of using a back exoskeleton for workers' musculoskeletal health need further clarification. The detected changes by using the Laevo® illustrate the need for further investigation prior to practical recommendations of using exoskeletons in the field. Investigating various work scenarios in different kind of workers and long-term applications would be important elements.

Porous SiOCH thin films for gravimetric gas sensors

The increasing need for on-site and real-time analyses of complex gas mixtures drives the development of several sensing approaches. In case of gravimetric sensors, a chemical sensitive layer is often required to improve the target molecule detection. Numerous materials are studied in the literature but only few are really compatible with the manufacturing of silicon-based sensing devices. This paper is focused on the gas detection ability of porous organosilicates thin films deposited by plasma enhanced chemical vapor deposition that are already used as low-k dielectric in microprocessors. A large panel of porous SiOCH were deposited on quartz crystal microbalances and were studied in the case of toluene and pentane detection. By using three different synthesis approaches, variations in open porosity, mean pore size and chemical composition were investigated. A large affinity to toluene and pentane is observed with partition coefficients higher than 20,000 in the case of toluene. These values are far above those reported for usually known polymers. The kinetic responses are in the range of a few minutes which is fast compared to the literature. Ellipsometry porosimetry (EP) characterizations, performed to obtain adsorption isotherms, highlight the role of porosity and more precisely of microporosity. Materials with smaller pores present higher affinity to pentane and toluene than materials with larger pores. Besides, EP appears to be an efficient technique to classify chemical sensitive layers. Finally, these porous SiOCH that present a good chemical stability and a hydrophobicity are promising sensitive layers for the manufacturing of NEMS-based gravimetric sensors integrated on silicon.

Recent progress on MOF-based optical sensors for VOC sensing.

The raising apprehension of volatile organic compound (VOC) exposures urges the exploration of advanced monitoring platforms. Metal-organic frameworks (MOFs) provide many attractive features including tailorable porosity, high surface areas, good chemical/thermal stability, and various host-guest interactions, making them appealing candidates for VOC capture and sensing. To comprehensively exploit the potential of MOFs as sensing materials, great efforts have been dedicated to the shaping and patterning of MOFs for next-level device integration. Among different types of sensors (chemiresistive sensors, gravimetric sensors, optical sensors, etc.), MOFs coupled with optical sensors feature distinctive strength. This review summarized the latest advancements in MOF-based optical sensors with a particular focus on VOC sensing. The subject is discussed by different mechanisms: colorimetry, luminescence, and sensors based on optical index modulations. Critical analysis for each system highlighting practical aspects was also deliberated.