Single-junction GaAs Solar Cells Research Articles

Carrier extraction behaviour in type II GaSb/GaAs quantum ring solar cells

The introduction of quantum dot (QD) or quantum ring (QR) nanostructures into GaAs single-junction solar cells has shown enhanced photo-response above the GaAs absorption edge, because of sub-bandgap photon absorption. However, to further improve solar cell performance a better understanding of the mechanisms of photogenerated carrier extraction from QDs and QRs is needed. In this work we have used a direct excitation technique to study type II GaSb/GaAs quantum ring solar cells using a 1064 nm infrared laser, which enables us to excite electron–hole pairs directly within the GaSb QRs without exciting the GaAs host material. Temperature and laser intensity dependence of the current–voltage characteristics revealed that the thermionic emission process produced the dominant contribution to the photocurrent and accounts for 98.9% of total photocurrent at 0 V and 300 K. Although the tunnelling process gives only a low contribution to the photocurrent, an enhancement of the tunnelling current was clearly observed when an external electric field was applied.

Photovoltaic Characteristics of Low-density Concentration GaAs Solar Cells with/without Anti-reflective Coating

We have studied photovoltaic characteristics of single-junction GaAs solar cells with/without an <TEX>$MgF_2/ZnS$</TEX> anti-reflective coating (ARC) illuminated by low-density concentration (<10 suns). By the ARC deposition, the short-circuit current density (<TEX>$J_{SC}$</TEX>) and the fill factor (FF) are increased by <TEX>$5mA/cm^2$</TEX> and 5% at a standard illumination (1 sun), respectively, and the resulted conversion efficiency is enhanced by 45%. In contrast with the cell with no ARC showing a rapid degradation with increasing concentration power, the efficiency of ARC-deposited cell remains almost constant as (<TEX>$17.7{\pm}0.3$</TEX>)% regardless of the concentration. It informs that ARC treatment is very effective in GaAs concentrator solar cells.

Epitaxial lift-off of quantum dot enhanced GaAs single junction solar cells

InAs/GaAs strain-balanced quantum dot (QD) n-i-p solar cells were fabricated by epitaxial lift-off (ELO), creating thin and flexible devices that exhibit an enhanced sub-GaAs bandgap current collection extending into the near infrared. Materials and optical analysis indicates that QD quality after ELO processing is preserved, which is supported by transmission electron microscopy images of the QD superlattice post-ELO. Spectral responsivity measurements depict a broadband resonant cavity enhancement past the GaAs bandedge, which is due to the thinning of the device. Integrated external quantum efficiency shows a QD contribution to the short circuit current density of 0.23 mA/cm2.

Single-material zinc sulfide bi-layer antireflection coatings for GaAs solar cells

We demonstrated the efficiency improvement of GaAs single-junction (SJ) solar cells with the single-material zinc sulfide (ZnS) bi-layer based on the porous/dense film structure, which was fabricated by the glancing angle deposition (GLAD) method, as an antireflection (AR) coating layer. The porous ZnS film with a low refractive index was formed at a high incident vapor flux angle of 80° in the GLAD. Each optimum thickness of ZnS bi-layer was determined by achieving the lowest solar weighted reflectance (SWR) using a rigorous coupled-wave analysis method in the wavelength region of 350-900 nm, extracting the thicknesses of 20 and 50 nm for dense and porous films, respectively. The ZnS bi-layer with a low SWR of ~5.8% considerably increased the short circuit current density (J(sc)) of the GaAs SJ solar cell to 25.57 mA/cm(2), which leads to a larger conversion efficiency (η) of 20.61% compared to the conventional one without AR layer (i.e., SWR~31%, J(sc) = 18.81 mA/cm(2), and η = 14.82%). Furthermore, after the encapsulation, its J(sc) and η values were slightly increased to 25.67 mA/cm(2) and 20.71%, respectively. For the fabricated solar cells, angle-dependent reflectance properties and external quantum efficiency were also studied.

Design of GaAs Solar Cells Operating Close to the Shockley–Queisser Limit

With recent advances in device design, single-junction GaAs solar cells are approaching their theoretical efficiency limits. Accurate numerical simulation may offer insights that can help close the remaining gap between the practical and theoretical limits. Significant care must be taken, however, to ensure that the simulation is self-consistent and properly comprehends thermodynamic limits. In this paper, we use rigorous photon recycling simulation coupled with carrier transport simulation to identify the dominant loss mechanisms that limit the performance of thin-film GaAs solar cells.

Influences of InGaP Conical Frustum Nanostructures on the Characteristics of GaAs Solar Cells

Conical frustums with quasihexagonal nanostructures are fabricated on an InGaP window layer of single junction GaAs solar cells using a polystyrene nanosphere lithography technique followed by anisotropic etching processes. The optical and photovoltaic characteristics of the conical frustum nanostructured solar cells are investigated. Reflectance of the conical frustum nanostructured solar cells is significantly reduced in a wide range of wavelengths compared to that of the planar sample. The measured reflectance reduction is attributed to the gradual change in the refractive index of the InGaP conical frustum window layer. An increase of 15.2% in the power conversion efficiency has been achieved in the fabricated cell with an optimized conical frustum nanostructure compared to that of the planar cell.

Enhanced Efficiency of GaAs Single-Junction Solar Cells with Inverted-Cone-Shaped Nanoholes Fabricated Using Anodic Aluminum Oxide Masks

The GaAs solar cells are grown by low-pressure metalorganic chemical vapor deposition (LP-MOCVD) and fabricated by photolithography, metal evaporation, annealing, and wet chemical etch processes. Anodized aluminum oxide (AAO) masks are prepared from an aluminum foil by a two-step anodization method. Inductively coupled plasma dry etching is used to etch and define the nanoarray structures on top of an InGaP window layer of the GaAs solar cells. The inverted-cone-shaped nanoholes with a surface diameter of about 50 nm are formed on the top surface of the solar cells after the AAO mask removal. Photovoltaic and optical characteristics of the GaAs solar cells with and without the nanohole arrays are investigated. The reflectance of the AAO nanopatterned samples is lower than that of the planar GaAs solar cell in the measured range. The short-circuit current density increased up to 11.63% and the conversion efficiency improved from 10.53 to 11.57% under 1-sun AM 1.5 G conditions by using the nanohole arrays. Dependence of the efficiency enhancement on the etching depth of the nanohole arrays is also investigated. These results show that the nanohole arrays fabricated with an AAO technique may be employed to improve the light absorption and, in turn, the conversion efficiency of the GaAs solar cell.

Improved optical absorption and photocurrent of GaAs solar cells with hexagonal micro-hole array surface texturing

We demonstrate an improvement in power conversion efficiency of single-junction GaAs solar cells incorporated with micro-hole arrays. The GaAs solar cells are grown by low-pressure metalorganic chemical vapor deposition on (100) GaAs substrates. The micro-hole arrays were formed on the surface of the GaAs solar cells, and the measurement on the reflectance and photocurrent generation are performed using an UV–Vis–NIR spectrometer and an external quantum efficiency measurement system, respectively. It is shown that the micro-hole arrays have the effect of scattering the incident light away from the original direction resulting in the reduction of reflectance over 350–873nm spectrum regime. The micro-hole arrays formed on the surface of the solar cells enhanced the photocurrent generation which was increased with the extended optical path length in the absorption layer. As a result, an enhancement in power conversion efficiency of up to 12.3% compared to that of reference solar cell was obtained under 1sun AM 1.5G illumination at room temperature.

Novel Anti-Reflection Technology for GaAs Single-Junction Solar Cells Using Surface Patterning and Au Nanoparticles

Single-junction GaAs solar cell structures were grown by low-pressure MOCVD on GaAs (100) substrates. Micro-rod arrays with diameters of 2 microm, 5 microm, and 10 microm were fabricated on the surfaces of the GaAs solar cells via photolithography and wet chemical etching. The patterned surfaces were coated with Au nanoparticles using an Au colloidal solution. Characteristics of the GaAs solar cells with and without the micro-rod arrays and Au nanoparticles were investigated. The short-circuit current density of the GaAs solar cell with 2 microm rod arrays and Au nanoparticles increased up to 34.9% compared to that of the reference cell without micro-rod arrays and Au nanoparticles. The conversion efficiency of the GaAs solar cell that was coated with Au nanoparticles on the patterned surface with micro-rod arrays can be improved from 14.1% to 19.9% under 1 sun AM 1.5G illumination. These results show that micro-rod arrays and Au nanoparticle coating can be applied together in surface patterning to achieve a novel cost-effective anti-reflection technology.

High-efficiency GaAs and GaInP solar cells grown by all solid-state molecular-beam-epitaxy

We report the initial results of GaAs and GaInP solar cells grown by all solid-state molecular-beam-epitaxy (MBE) technique. For GaAs single-junction solar cell, with the application of AlInP as the window layer and GaInP as the back surface field layer, the photovoltaic conversion efficiency of 26% at one sun concentration and air mass 1.5 global (AM1.5G) is realized. The efficiency of 16.4% is also reached for GaInP solar cell. Our results demonstrate that the MBE-grown phosphide-contained III-V compound semiconductor solar cell can be quite comparable to the metal-organic-chemical-vapor-deposition-grown high-efficiency solar cell.

The Circle-Grid Electrode on Concentrated GaAs Solar Cells Efficiency

The relationship between front contact pattern of GaAs single-junction solar cell with conversion efficiency at different concentration ratios is studied in this paper. Five different front circle-grid patterns were designed and patterned on the in-house fabricated single junction GaAs solar cells. At high light concentration ratio, the cell efficiency is strongly dependent on the series resistance of the electrode. At the same time, the thermal effect should also be taken into consideration, especially when a device is operating under high concentration ratio. Therefore, the aim of this work is to find a suitable front contact pattern for a GaAs single-junction solar cell to increase the conversion efficiency under high concentration solar radiation. It is found that the device with proper pattern design geometrical shadowing factor of 7.1% has the best cell efficiency of 27.05% at CR>100x, AM1.5G.

Intermediate-Band Solar Cells Based on InAs/GaAs Quantum Dots

We report the fabrication of intermediate-band solar cells (IBSCs) based on quantum dots (QDs), which consists of a standard P-I-N structure with multilayer stacks of InAs/GaAs QDs in the I-layer. Compared with conventional GaAs single-junction solar cells, the IBSCs based on InAs/GaAs QDs show a broader photo-response spectrum (> 1330 nm), a higher short-circle current (about 53% increase) and a stronger radiation hardness. The results have important applications for realizing high efficiency solar cells with stronger radiation hardness.

Stretchable GaAs Photovoltaics with Designs That Enable High Areal Coverage

Strategies are presented for achieving, simultaneously, both large areal coverage and high stretchability by using elastomeric substrates with surface relief in geometries that confine strains at the locations of the interconnections, and away from the devices. The studies involve a combination of theory and experiment to reveal the essential mechanics, and include demonstrations of the ideas in stretchable solar modules that use ultrathin, single junction GaAs solar cells.

Solar cell technology on the base of III–V heterostructures

Low-cost single-junction GaAs solar cells on the base of p-AlGaAs/p-GaAs/ n-GaAs heterostructures grown by low-temperature liquid-phase epitaxy have been fabricated. For analyzing the factors contributing to solar cell efficiency the program products PC1D have been used. The optimal doping concentrations and thicknesses of the layers which correspond to the maximum values of the solar cell output parameters have been determined. The multilayer solar cell structure has been optimized on the base of this simulation. Low cost technological processes and masks, necessary for fabrication of the cells on the base of the grown heterostructures, have been developed, too. The front and back metallization of the cell is Ni/Al system deposited by magnetron sputtering. A double layer Al2O3 /ZrO2 antireflection coating is deposited on the front side of a solar cell structure by the spin coating technique. The conversion efficiencies of 19 % at one sun AM1.5 conditions have been measured.

Degradation mechanism analysis in temperature stress tests on III–V ultra-high concentrator solar cells using a 3D distributed model

A temperature stress test was carried out on GaAs single-junction solar cells to analyze the degradation suffered when working at ultra-high concentrations. The acceleration of the degradation was realized at two different temperatures: 130 °C and 150 °C. In both cases, the degradation trend was the same, and only gradual failures were observed. A fit of the dark I–V curve at 25 °C with a 3D distributed model before and after the test was done. The fit with the 3D distributed model revealed degradation at the perimeter because the recombination current in the depletion region of the perimeter increased by about fourfold after the temperature stress test. Therefore, this test did not cause any morphological change in the devices, and although the devices were isolated with silicone, the perimeter region was revealed as the most fragile component of the solar cell. Consequently, the current flowing beneath the busbar favors the progression of defects in the device in the perimeter region.

High material efficiency MOVPE growth with in situ monitoring

The possibility of growing a GaAs single-junction solar cell structure with high growth rate and low partial pressure of tertiary-butylarsine (TBAs) has been explored in order to minimize the cost and material consumption in metal-organic vapor phase epitaxy (MOVPE). In situ surface reflectance anisotropy measurements suggested that we can grow reasonable quality GaAs layers at a growth rate of 3.3 μm/h and a V/III ratio of 2.5. Dark current–voltage characteristics of the pn junction that was grown at this condition yielded an ideality factor of 1.3, which was equivalent to the value obtained with a lower growth rate and higher V/III ratio, suggesting a possibility that we can grow GaAs with reasonable crystal quality at a high material efficiency. However, there seemed to exist spots of accumulated defects with a spacing of hundreds of micrometers at such a growth condition with a high material efficiency. If they are situated in the vicinity of the pn junction, the efficiency of the PV cell was significantly degraded, which suggests the necessity of tuning the growth conditions according to the impact of a layer on the electrical properties of a PV cell.

26.1% thin-film GaAs solar cell using epitaxial lift-off

The epitaxial lift-off technique can be used to separate a III–V solar cell structure from its underlying GaAs substrate. Processing a thin-film cell is somewhat different from a regular cell on substrate. In this work a number of critical issues, e.g., a low-temperature anneal front contact and the metal mirror on backside of the thin-film are optimized. Together with an improved active layer material quality, grid mask and anti-reflection coating this leads to thin-film cells as good as cells on a substrate, with record efficiencies for single junction GaAs solar cells of 26.1% for both cell types.

A study on the electric properties of single-junction GaAs solar cells under the combined radiation of low-energy protons and electrons

Displacement damage induced by charged particle radiation is the main cause of degradation of orbital-service solar cells, while the radiation-induced ionization shows no permanent damage effect on their electrical properties. It is reported that in single crystal silicon solar cells, low-energy electron radiation does not exert permanent degradation of their properties, but the fluence of electron radiation exerts an influence on the damage magnitude under the combined radiation of protons and electrons. The electrical properties of the single-junction GaAs/Ge solar cells were investigated after irradiation by sequential and synchronous electron and proton beams. Low-energy electron radiation showed no effects on the change of the solar cell properties during sequential or synchronous irradiation, implying ionization during particle radiation could not exert influence on the displacement damage process to the solar cells under the experimental conditions.

Quantum Dot Spectral Tuning of Multijunction III-V Solar Cells

AbstractImproving the production of photocurrent in the middle junction of a InGaP/Ga(In)As/Ge triple-junction solar cells (TJSC) can improve the overall conversion efficiency of cell. One possible method to improve the middle junction photocurrent is inserting a quantum dot (QD) superlattice (SL) into the stack. It has been predicted that QD-SL enhanced TJSCs have an efficiency ceiling of 47% under a one-sun AM0 illumination spectrum. Additionally, QD array enhanced GaAs cells have the added benefit of possible intermediate band effects, anisotropic absorption and enhanced radiation tolerance. Embedding InAs quantum dots (QDs) in a single junction GaAs solar cell can increase sub-GaAs bandgap photocurrent generation. This method has been shown to improve the short circuit current density (Jsc) of single junction cells under simulated 1 sun air mass zero (AM0) illumination. However, the increase in strain due to the InAs QD self-assembly may cause defects that reduce the minority carrier lifetime resulting in losses in the cell open circuit voltage (Voc) on the order of 300-500 mV. The introduction of strain compensation (SC) layers into the superlattice (SL) structure of a QD solar cell has previously been shown to improve the device performance, including the partial recovery of Voc. Strain compensation can be used effectively to balance the residual strain, impede dislocation formation, and improve the solar cell characteristics. The effect of GaP strain compensation on the solar cell electrical and material properties was investigated. High resolution X-ray diffraction (HRXRD) scans along the symmetric (004) Bragg peak show weak intensity and wide FWHM at the zero order SL peak (SL0) for non-SC samples. Optimum SC thickness was theoretically determined using a zero in plane stress method and experimentally verified using HRXRD. Optimal strain compensation was then used to increase the QD SL stacking from 5x to 10x and 20x. Use of SC resulted in shifting of the SL0 peak toward the substrate peak as well as reduced FWHM and improved SL peak definition. Kinematical diffraction modeling of the QD structures using numerical simulation indicated this peak shift resulted from reduced overall strain in the SL stack up to 5ML of SC. The material quality improvement in the SC QD solar cells was manifested in an improved spectral response and Jsc. The optoelectronic results for GaAs solar cells with QD SL’s demonstrate a strong dependence on GaP SC layer thickness. In addition, comparison of multi junction (MJ) solar cells which incorporate the SC QD SL’s demonstrate the utility of additional sub-GaAs bandgap current contribution as a tool for additional current-matching optimization in MJ solar cells.

III-V Device Integration on Silicon Via Metamorphic SiGe Substrates

A range of high performance minority carrier devices have been successfully fabricated on Si virtual substrates where threading dislocation densities (TDDs) as low as 1x106 cm-2 are routinely achieved. Minority carrier lifetime data achieved on GaAs-on-Si layers exploiting this novel SiGe buffer approach to monolithic integration (τp = 10.5 ns and τn = 1.7ns) verifies the high III-V material quality. Single junction GaAs solar cells with high efficiencies for GaAs/Si of 18.1% under AM1.5-G illumination were demonstrated. Further exploiting the novel GaAs/Si material quality, even more complex minority carrier devices including dual-junction solar cells and LEDs were fabricated, yielding high performance consistent with the high III-V/Si mobilities. In both cases, certain device metrics on SiGe outperformed identical GaAs monolithic devices. Finally, a visible laser on Si was achieved, demonstrating the success and further potential of this III-V/Si integration methodology.