Free-standing Membranes Research Articles

Highly Efficient, Flexible, and Self-Healable Moisture-Driven Energy Harvester Based on 2D Vanadium Pentoxide Nanosheets

The ubiquitous source of atmospheric moisture brought about a fascinating research avenue of extracting atmospheric water to generate sustainable electricity. Energy may be extracted from ambient moisture with obvious and substantial advantages. This point-of-use technology provides a decentralized alternative to meet the energy needs in isolated off-grid places. Unlike traditional energy generators which predominantly rely upon fossil fuel, moisture-induced energy generators can extract energy from moisture in a sustainable and eco-friendly way. Herein, we demonstrated a self-healable moist electric generator (MEG) based on vanadium pentoxide (V2O5) 2D nanosheet membranes. Lamellar membranes of V2O5 nanosheets have been shown to be excellent cation conductors and excellent materials for harvesting energy from ambient moisture. Ultra-thin 2D nanosheets of V2O5 was obtained by treatment of bulk V2O5 crystals with hydrogen peroxide. V2O5 nanosheet membrane was fabricated by vacuum-assisted filtration of 2D V2O5 nanosheets dispersion over a PTFE support membrane. The V2O5 membrane was easily peeled off from the support membrane on drying to obtain a flexible and freestanding V2O5 membrane. The V2O5 membrane consisting of percolated nanofluidic channels was sandwiched between a bottom solid copper foil and a perforated copper foil as the bottom electrode. The top electrode is perforated for exposure to atmospheric humidity. As the atmospheric water molecules come in contact with the V2O5 surface, an open-circuit voltage of 0.5 Volts and a short-circuit current of 0.3 microamperes is generated. The generated voltage and current is attributed to the preferential flow of cations through the V2O5 nanochannels. The exposed surface and edges of V2O5 nanosheets have a high negative surface charge which results in the splitting of water molecules into H3O+ and OH- ions. An electrical double layer (EDL) is established at the V2O5/water interface which selectively permits H3O+ ions through the channels. The mobile ions of the EDL transport through the nanofluidic channels creating a gradient between the two electrodes, resulting in a constant potential difference between the top and bottom electrodes which is harvested as electric current. The MEGs can be easily connected in parallel or series to enhance the current and voltage respectively. We demonstrate ten MEGs connected in series to power small electronic devices such as calculators and humidity meters. One of the key features of the V2O5 MEG is its ability to repair any physical damage to the active material owing to the water-assisted healing characteristics V2O5 membrane. Figure 1

Crystalline Porous Organic Cage Membranes Constructed Using Fortified Intermolecular Interactions for Molecular Sieving.

Among the various types of materials with intrinsic porosity, porous organic cages (POCs) are distinctive as discrete molecules that possess intrinsic cavities and extrinsic channels capable of facilitating molecular sieving. However, the fabrication of POC membranes remains highly challenging due to the weak noncovalent intermolecular interactions and most reported POCs are powders. In this study, we constructed crystalline free-standing porous organic cage membranes by fortifying intermolecular interactions through the induction of intramolecular hydrogen bonds, which was confirmed by single-crystal X-ray analysis. To elucidate the driving forces behind, a series of terephthaldehyde building blocks containing different substitutions were reacted with flexible triamine under different conditions via interfacial polymerization (IP). Furthermore, density functional theory (DFT) calculations suggest that intramolecular hydrogen bonding can significantly boost the intermolecular interactions. The resulting membranes exhibited fast solvent permeance and high rejection of dyes not only in water, but also in organic solvents. In addition, the membrane demonstrated excellent performance in precise molecular sieving in organic solvents. This work opens an avenue to designing and fabricating free-standing membranes composed of porous organic materials for efficient molecular sieving.

Giant Piezoelectric Effects of Topological Structures in Stretched Ferroelectric Membranes.

Freestanding ferroelectric oxide membranes emerge as a promising platform for exploring the interplay between topological polar ordering and dipolar interactions that are continuously tunable by strain. Our investigations combining density functional theory (DFT) and deep-learning-assisted molecular dynamics simulations demonstrate that DFT-predicted strain-driven morphotropic phase boundary involving monoclinic phases manifest as diverse domain structures at room temperatures, featuring continuous distributions of dipole orientations and mobile domain walls. Detailed analysis of dynamic structures reveals that the enhanced piezoelectric response observed in stretched PbTiO_{3} membranes results from small-angle rotations of dipoles at domain walls, distinct from conventional polarization rotation mechanism and adaptive phase theory inferred from static structures. We identify a ferroelectric topological structure, termed "dipole spiral," which exhibits a giant intrinsic piezoelectric response (>320 pC/N). This helical structure, possessing a rotational zero-energy mode, unlocks new possibilities for exploring chiral phonon dynamics and dipolar Dzyaloshinskii-Moriya-like interactions.

A Rapid, Efficient Method for Anodic Aluminum Oxide Membrane Room-Temperature Multi-Detachment from Commercial 1050 Aluminum Alloy.

For commercial processes, through-hole AAO membranes are fabricated from high-purity aluminum by chemical etching. However, this method has the disadvantages of using heavy-metal solutions, creating large amounts of material waste, and leading to an irregular pore structure. Through-hole porous alumina membrane fabrication has been widely investigated due to applications in filters, nanomaterial synthesis, and surface-enhanced Raman scattering. There are several means to obtain freestanding through-hole AAO membranes, but a fast, low-cost, and repetitive process to create complete, high-quality membranes has not yet been established. Here, we propose a rapid and efficient method for the multi-detachment of an AAO membrane at room temperature by integrating the one-time potentiostatic (OTP) method and two-step electrochemical polishing. Economical commercial AA1050 was used instead of traditional high-cost high-purity aluminum for AAO membrane fabrication at 25 °C. The OTP method, which is a single-step process, was applied to achieve a high-quality membrane with unimodal pore distribution and diameters between 35 and 40 nm, maintaining a high consistency over five repetitions. To repeatedly detach the AAO membrane, two-step electrochemical polishing was developed to minimize damage on the AA1050 substrate caused by membrane separation. The mechanism for creating AAO membranes using the OTP method can be divided into three major components, including the Joule heating effect, the dissolution of the barrier layer, and stress effects. The stress is attributed to two factors: bubble formation and the difference in the coefficient of thermal expansion between the AAO membrane and the Al substrate. This highly efficient AAO membrane detachment method will facilitate the rapid production and applications of AAO films.

Uniform, Fully Connected, High-Quality Monocrystalline Freestanding Perovskite Oxide Films Fabricated from Recyclable Substrates.

Releasing epitaxial perovskite oxide films from their native oxide substrates produces high quality, 2D-material-like monocrystalline freestanding oxide membranes, as potential key components for the next-generation electronic devices. Two major obstacles still limit their practical applications: macroscopic material defects (mainly cracks) that lowers uniformity and yield, and the high cost of the consumed oxide substrates. Here, a two-step film transfer method and a substrate recycling method enable repetitive fabrication of millimeter-scale, fully-connected freestanding oxide films of various chemical compositions from the same substrates; arrays of capacitor and resistor devices based on these oxides transferred on silicon indicate high uniformity, low sample-to-sample variation, and satisfactory electrical connectivity. The two-step transfer suppresses crack formation by avoiding buckling-delamination-type relaxation of epitaxial strain, and the key point to achieve substrate reuse is to remove the residual Al species bonded to the substrate surfaces. The mitigation of such long-lasting issues in freestanding oxide fabrication techniques may eventually pave roads toward future industrial-grade devices, as well as enabling many research opportunities in fundamental physics.

Ultrafast 2D Nanosheet Assembly via Spontaneous Spreading Phenomenon.

In 2D materials, a key engineering challenge is the mass production of large-area thin films without sacrificing their uniform 2D nature and unique properties. Here, it is demonstrated that a simple fluid phenomenon of water/alcohol solvents can become a sophisticated tool for self-assembly and designing organized structures of 2D nanosheets on a water surface. In situ, surface characterizations show that water/alcohol droplets of 2D nanosheets with cationic surfactants exhibit spontaneous spreading of large uniform monolayers within 10s. Facile transfer of the monolayers onto solid or flexible substrates results in high-quality mono- and multilayer films with high coverages (>95%) and homogeneous electronic/optical properties. This spontaneous spreading is quite general and can be applied to various 2D nanosheets, including metal oxides, graphene oxide, h-BN, MoS2, and transition metal carbides, enabling on-demand smart manufacture of large-size (>4 inchϕ) 2D nanofilms and free-standing membranes.

Unfolding the Challenges To Prepare Single Crystalline Complex Oxide Membranes by Solution Processing.

The ability to prepare single crystalline complex oxide freestanding membranes has opened a new playground to access new phases and functionalities not available when they are epitaxially bound to the substrates. The water-soluble Sr3Al2O6 (SAO) sacrificial layer approach has proven to be one of the most promising pathways to prepare a wide variety of single crystalline complex oxide membranes, typically by high vacuum deposition techniques. Here, we present solution processing, also named chemical solution deposition (CSD), as a cost-effective alternative deposition technique to prepare freestanding membranes identifying the main processing challenges and how to overcome them. In particular, we compare three different strategies based on interface and cation engineering to prepare CSD (00l)-oriented BiFeO3 (BFO) membranes. First, BFO is deposited directly on SAO but forms a nanocomposite of Sr-Al-O rich nanoparticles embedded in an epitaxial BFO matrix because the Sr-O bonds react with the solvents of the BFO precursor solution. Second, the incorporation of a pulsed laser deposited La0.7Sr0.3MnO3 (LSMO) buffer layer on SAO prior to the BFO deposition prevents the massive interface reaction and subsequent formation of a nanocomposite but migration of cations from the upper layers to SAO occurs, making the sacrificial layer insoluble in water and withholding the membrane release. Finally, in the third scenario, a combination of LSMO with a more robust sacrificial layer composition, SrCa2Al2O6 (SC2AO), offers an ideal building block to obtain (001)-oriented BFO/LSMO bilayer membranes with a high-quality interface that can be successfully transferred to both flexible and rigid host substrates. Ferroelectric fingerprints are identified in the BFO film prior and after membrane release. These results show the feasibility to use CSD as alternative deposition technique to prepare single crystalline complex oxide membranes widening the range of available phases and functionalities for next-generation electronic devices.

Vertical InGaN Light-Emitting Diode with Hybrid Distributed Bragg Reflectors.

A vertical-type InGaN light-emitting diode with a resonant cavity was demonstrated with a 9 μm aperture size and a short cavity formed by hybrid distributed Bragg reflectors (DBRs). The approach involved designing epitaxial structures and utilizing an electrochemical etching process to convert heavily doped n-type gallium nitride (n+-GaN) layers into porous GaN layers as a porous-GaN DBR structure. Thirteen pairs of the conductive porous-GaN:Si/GaN:Si DBR structure provided a vertical current path in a vertical-type light-emitting diodes (LED) structure. The LED epitaxial layers were separated from sapphire for membrane-type LED structures through a laser lift-off process. During the free-standing membrane fabrication process, the dielectric DBR deposited on ITO/p-GaN:Mg layers was inverted from top to bottom, thereby establishing the concept of higher reflectivity for the bottom DBR compared to the porous-GaN DBR. The physical cavity length was reduced from about 2.3 μm for the LED membrane to 0.74 μm for the membrane-type LED with the embedded porous-GaN DBR structure. The divergent angles and line width of EL emission light were reduced from 124°/31.7 nm to 44°/3.3 nm due to the resonant cavity effect. The membrane-type LED structures with hybrid DBRs consisted of small divergent angles, narrow line width, and vertical current injection properties that have potential for directional emission light sources and vertical-cavity surface-emitting diode laser applications.

Enhanced interlayer interaction in sulfonated CONs membrane by amino-rich CONs enabling ultrafast proton transport

Covalent organic framework nanosheets (CONs) with porous crystalline features and ultrathin thickness are ideal candidates as membrane building blocks to form well-defined transfer nanochannels. The formidable challenge behind self-supporting CONs membrane lies in weak non-covalent interlayer interactions and thus loose stacking, insufficient strength and structure stabilities. Herein, we propose the fabrication of interlayer force-strengthened freestanding CONs membrane through the electrostatic attraction bridge effect of positively-charged amino-rich CONs (CON–NH2) to negatively-charged sulfonated CONs (CON–SO3H). Ultrathin and large lateral sized CON–SO3H and CON–NH2 are synthesized, followed by restacking to prepare freestanding CONs membrane with CON–SO3H as the membrane bulk. Benefiting from effective interlayer interconnection due to strong electrostatic interaction, the obtained CON–SO3H/CON–NH2 membrane displays features of ultrahigh integrity, dense stacking, eminent water/acid/base/organic solvents stabilities and mechanical strength (109 MPa). The shortened –SO3H distance contributes to construct site-continuous transfer pathways, and the deprotonated –SO3H and protonated –NH2 form acid–base pairs to decrease interfacial resistance, which impart membrane superior proton conductivity of 486 mS cm−1 (80 °C, 100% RH). This interlayer force enhancement strategy offers a promising perspective on achieving densely-stacked CONs membrane with ultrahigh mechanical property and conduction performance for fuel cell application.

Flexible strained membranes of multiferroic TbMnO3

The multiferroic properties of TbMnO3 demonstrate high versatility under applied pressure, making the material potentially suitable for use in flexible electronics. Here, we report on the preparation of elastic freestanding TbMnO3 membranes with dominant (001) or (010) crystallographic out-of-plane orientation. Membranes with a thickness of 20 nm display orthorhombic bulk-like relaxed lattice parameters with strong suppression of twinning for the (010) oriented membranes. Strain in flexible membranes was tuned using a commercial strain cell device and characterized by Raman spectroscopy. The B1g out-of-phase oxygen-stretching mode, representative of the Mn–O bond distance, systematically shifts to lower energy with increasing strain (εmax ≈ 0.5%). The flexibility and elastic properties of the membranes allow for specific manipulation of the multiferroic state by strain, whereas the choice of the crystallographic orientation gives the possibility of an in- or out-of-plane electric polarization.

Ferroelectric freestanding hafnia membranes with metastable rhombohedral structure down to 1-nm-thick

Two-dimensional freestanding membranes of materials, which can be transferred onto and make interfaces with any material, have attracted attention in the search for functional properties that can be utilized for next-generation nanoscale devices. We fabricated stable 1-nm-thick hafnia membranes exhibiting the metastable rhombohedral structure and out-of-plane ferroelectric polarizations as large as 13 μC/cm2. We also found that the rhombohedral phase transforms into another metastable orthorhombic phase without the ferroelectricity deteriorating as the thickness increases. Our results reveal the key role of the rhombohedral phase in the scale-free ferroelectricity in hafnia and also provide critical insights into the formation mechanism and phase stability of the metastable hafnia. Moreover, ultrathin hafnia membranes enable heterointerfaces and devices to be fabricated from structurally dissimilar materials beyond structural constrictions in conventional film-growth techniques.

Superconductivity in Freestanding Infinite-Layer Nickelate Membranes.

The observation of superconductivity in infinite-layer nickelates has attracted significant attention due to its potential as a new platform for exploring high-Tc superconductivity. However, thus far, superconductivity has only been observed in epitaxial thin films, which limits the manipulation capabilities and modulation methods compared to two-dimensional exfoliated materials. Given the exceptionally giant strain tunability and stacking capability of freestanding membranes, separating superconducting nickelates from the as-grown substrate is a novel way to engineer the superconductivity and uncover the underlying physics. Herein, this work reports the synthesis of the superconducting freestanding La0.8Sr0.2NiO2 membranes ( ), emphasizing the crucial roles of the interface engineering in the precursor phase film growth and the quick transfer process in achieving superconductivity. This work offers a new versatile platform for investigating superconductivity in nickelates, such as the pairing symmetry via constructing Josephson tunneling junctions and higher Tc values via high-pressure experiments.

Acidochromic Free-Standing Multilayered Chitosan-Pyranoflavylium/Alginate Membranes toward Food Smart Packaging Applications.

Food smart packaging has emerged as a promising technology to address consumer concerns regarding food conservation and food safety. In this context, we report the rational design of azide-containing pyranoflavylium-based pH-sensitive dye for subsequent click chemistry conjugation toward a chitosan-modified alkyne. The chitosan-pyranoflavylium conjugate was characterized by infrared (ATR-FTIR), ultraviolet-visible (UV-vis), nuclear magnetic resonance (NMR) spectroscopies, and dynamic light scattering (DLS), as well as its thermodynamic parameters related to their pH-dependent chromatic features. The fabrication of thin-films through electrostatic-driven layer-by-layer (LbL) assembly technology was first screened by quartz crystal microbalance with dissipation monitoring (QCM-D) onto gold substrates, and then free-standing (FS) multilayered membranes from polypropylene substrate were obtained using a homemade automatic dipping robot. The membranes' characterization included morphology analysis and thickness evaluation, assessed by scanning electron microscopy (SEM), pH-responsive color change performance tests using buffer solutions at different pH levels, and biogenic amines-enriched model solutions, demonstrating the feasibility and effectiveness of the chitosan-pyranoflavylium/alginate biomembranes for food spoilage monitoring. This work provides insights toward the development of innovative pH-responsive smart biomaterials for advanced and sustainable technological packaging solutions, which could significantly contribute to ensuring food safety and quality, while reducing food waste.

Design and preparation of woven fabric-reinforced substrate: A new pathway for robust thin film composite membrane

The thin film composite (TFC) membrane possesses the highest commercial application potential among all types of forward osmosis (FO) membranes. The support layer of the membrane plays a crucial role in both bearing mechanical loads and facilitating the active layer formation. Herein, we addressed the issues of low permeability and poor mechanical strength of the conventional TFC FO membrane by selecting suitable fabrics and optimizing membrane design and preparation. Polyester (PS) woven fabric, with its high strength, low thickness, and high porosity, served as an excellent material for reinforcing the strength of the FO membrane. We employed a novel double-blade casting method to address the defect issue associated with the conventional single-blade casting method. The influencing factors and quality control strategies of the fabric-reinforced substrate were systematically investigated. Furthermore, membrane characterization techniques, including scanning electron microscopy (SEM), liquid-liquid displacement porometer, and cross-flow FO system, were used to reveal the influences of different substrates, including polysulfone (PSU), polyacrylonitrile (PAN), and polyetherimide (PEI), on the structure and performance of the fabric-reinforced TFC-FO membrane. Compared to commercial FO membranes, the TFC/PSU membrane exhibited superior FO performance, with a water flux of 24.1 LMH, and outstanding mechanical strength that was more than 10-times higher than that of free-standing membranes. This study demonstrates a new pathway for engineering robust TFC-FO membranes with low structural parameters as well as excellent scalability of the membrane fabrication method.

Highly confined epsilon-near-zero and surface phonon polaritons in SrTiO3 membranes

Recent theoretical studies have suggested that transition metal perovskite oxide membranes can enable surface phonon polaritons in the infrared range with low loss and much stronger subwavelength confinement than bulk crystals. Such modes, however, have not been experimentally observed so far. Here, using a combination of far-field Fourier-transform infrared (FTIR) spectroscopy and near-field synchrotron infrared nanospectroscopy (SINS) imaging, we study the phonon polaritons in a 100 nm thick freestanding crystalline membrane of SrTiO3 transferred on metallic and dielectric substrates. We observe a symmetric-antisymmetric mode splitting giving rise to epsilon-near-zero and Berreman modes as well as highly confined (by a factor of 10) propagating phonon polaritons, both of which result from the deep-subwavelength thickness of the membranes. Theoretical modeling based on the analytical finite-dipole model and numerical finite-difference methods fully corroborate the experimental results. Our work reveals the potential of oxide membranes as a promising platform for infrared photonics and polaritonics.

Internal sites of actuation and activation in thin elastic films and membranes of finite thickness.

Functionalized thin elastic films and membranes frequently feature internal sites of net forces or stresses. These are, for instance, active sites of actuation, or rigid inclusions in a strained membrane that induce counterstress upon externally imposed deformations. We theoretically analyze the geometry of isotropic, flat, thin, linearly elastic films or membranes of finite thickness, laterally extended to infinity. At the mathematical core of such characterizations are the fundamental solutions for localized force and stress singularities associated with corresponding Green's functions. We derive such solutions in three dimensions and place them into the context of previous two-dimensional calculations. To this end, we consider both no-slip and stress-free conditions at the top and/or bottom surfaces. We provide an understanding for why the fully free-standing thin elastic membrane leads to diverging solutions in most geometries and compare these situations to the truly two-dimensional case. A no-slip support of at least one of the surfaces stabilizes the solution, which illustrates that the divergences in the fully free-standing case are connected to global deformations. Within the aforementioned framework, our results are important for associated theoretical characterizations of thin elastic films, whether supported or free-standing, and of membranes subject to internal or external forces or stresses.

Remarkable flexibility in freestanding single-crystalline antiferroelectric PbZrO3 membranes

The ultrahigh flexibility and elasticity achieved in freestanding single-crystalline ferroelectric oxide membranes have attracted much attention recently. However, for antiferroelectric oxides, the flexibility limit and fundamental mechanism in their freestanding membranes are still not explored clearly. Here, we successfully fabricate freestanding single-crystalline PbZrO3 membranes by a water-soluble sacrificial layer technique. They exhibit good antiferroelectricity and have a commensurate/incommensurate modulated microstructure. Moreover, they also have good shape recoverability when bending with a small radius of curvature (about 2.4 μm for the thickness of 120 nm), corresponding to a bending strain of 2.5%. They could tolerate a maximum bending strain as large as 3.5%, far beyond their bulk counterpart. Our atomistic simulations reveal that this remarkable flexibility originates from the antiferroelectric-ferroelectric phase transition with the aid of polarization rotation. This study not only suggests the mechanism of antiferroelectric oxides to achieve high flexibility but also paves the way for potential applications in flexible electronics.

Elastic Properties of Low-Dimensional Single-Crystalline Dielectric Oxides through Controlled Large-Area Wrinkle Generation.

Freestanding single-crystalline SrTiO3 membranes, as high-κ dielectrics, hold significant promise as the gate dielectric in two-dimensional (2D) flexible electronics. Nevertheless, the mechanical properties of the SrTiO3 membranes, such as elasticity, remain a critical piece of the puzzle to adequately address the viability of their applications in flexible devices. Here, we report statistical analysis on plane-strain effective Young's modulus of large-area SrTiO3 membranes (5 × 5 mm2) over a series of thicknesses (from 6.5 to 32.2 nm), taking advantage of a highly efficient buckling-based method, which reveals its evident thickness-dependent behavior ranging from 46.01 to 227.17 GPa. Based on microscopic and theoretical results, we elucidate these thickness-dependent behaviors and statistical data deviation with a bilayer model, which consists of a surface layer and a bulk-like layer. The analytical results show that the ∼3.1 nm surface layer has a significant elastic softening compared to the bulk-like layer, while the extracted modulus of the bulk-like layer shows a variation of ∼40 GPa. This variation is considered as a combined contribution from oxygen deficiency presenting in SrTiO3 membranes, and the alignment between applied strain and the crystal orientation. Upon comparison of the extracted elastic properties and electrostatic control capability to those of other typical gate dielectrics, the superior performance of single-crystalline SrTiO3 membranes has been revealed in the context of flexible gate dielectrics, indicating the significant potential of their application in high-performance flexible 2D electronics.

One-step synthesis of freestanding and translucent ZrO2 nanotube membranes by direct electrochemical anodization

One-step synthesis of freestanding zirconium oxide nanotube (ZrO2-NT) membranes was obtained by direct electrochemical anodization of zirconium (Zr) substrates in aqueous electrolytes (mixture of 1 M (NH4)2SO4 and 0.75 M NH4F). The maximum membrane area was 9 cm2 and showed translucency from 400 to 700 nm. The ZrO2-NTs have an external diameter of ∼80 nm, an internal diameter of ∼55 nm, and a length of ∼22.5 μm. Moreover, the ZrO2-NTs showed a cubic crystal structure after anodization. The results are highly promising for applications requiring independent ZrO2 nanotube membranes.

Evaporation-induced self-assembled ultrathin AgNW networks for highly conformable wearable electronics

The flexibility and stability of transparent electrodes play a crucial role in the growing popularity of flexible devices, especially in potential wearable electronics. To date, various solution-coating techniques have been developed for fabricating silver nanowire (AgNW) flexible bioelectronics. However, achieving the orderly distributed patterns of AgNW without undesirable aggregations still poses a grand challenge. Here, an approach to realize regular patterned ultrathin AgNW networks on a freestanding electrospun PVDF-TrFE frame by evaporation-induced self-assembly is proposed. The patterning mechanism of evaporating AgNW colloidal suspension is investigated from experimental and theoretical analysis. The influence of evaporation-induced flow inside colloidal freestanding membranes on forming regular square hole-shaped arrays, selective deposition of AgNW, and aligning them along the artificial pinning array are addressed. Owing to the orderly arrangement of AgNW networks, the resultant flexible electrode achieves ultrathin thickness (about 5 μm), high optical transmittance (87.8%), and low sheet resistance (8.4 Ω·sq−1) with a relatively low dosage of AgNW (9 μg·cm−2). The electrode exhibits excellent durability during cyclic bending (50,000 times) and stretching (50% strain). The resistance remains virtually unchanged during 200 days in everyday environments. Furthermore, the excellent conformability and breathability of the flexible transparent electrode attached to the human skin demonstrates its potential application as an e-skin sensor. Our findings reliably urge a simple approach to underscore better outcomes with effective patterns by self-assembly of AgNW for highly conformal wearable electronics.