Fracture Formation Research Articles

(Invited) Using a Chemo-Mechanical Model to Investigate Electrolyte Infiltration and Surface Reconstruction within Cracked Cathode Material

One of the main goals in modeling lithium-ion batteries is to improve/predict longevity and resilience of new chemistries. To that end, this talk investigates the formation of stress-induced fracture within polycrystalline cathode particles and the impact on capacity loss. The model captures anisotropic Li diffusion within a single polycrystalline particle comprised of hundreds to thousands of randomly oriented grains. Fracture is primarily due to non-ideal grain interactions with slight dependence on high-rate charge demands. Essentially, when neighboring grains are misaligned, they expand a different rates relative to one another leading to high stresses and ultimately the formation of intraparticle cracks. A previous study showed that small particle with large or single grain geometry tend to crack less and retain the most capacity.Cracks within the cathode particle that have access to the surface can potentially fill with electrolyte. When this happens, the cracks can be considered new active surface area where the lithium intercalation reaction can occur. Under sufficient conditions, this could lead to better performance because the grains of the cracked particle start to operate more like a network of single-grain particles. However, the newly open surface area is also subject to side reactions and surface reconstruction resulting in diminished transport properties and potentially trapped lithium. The goal of this talk is to investigate this balance between improved lithium transport pathways caused by lithium infiltration and the reduced diffusion due to surface reconstruction.

High-Strength Controllable Resin Plugging Agent and Its Performance Evaluation for Fractured Formation.

Lost circulation is a common and complicated situation in drilling engineering. Serious lost circulation may lead to pressure drop in the well, affect normal drilling operations, and even cause wellbore instability, formation fluid flooding into the wellbore, and blowout. Therefore, appropriate preventive and treatment measures need to be taken to ensure the safe and smooth operation of drilling operations. So, it is necessary to conduct in-depth research on the development and performance of the plugging materials. In this study, urea formaldehyde resin with high temperature resistance and strength was used as the main raw material, and the curing conditions were optimized and adjusted by adding a variety of additives. The curing time, compressive strength, temperature resistance, and other key performance indexes of the resin plugging agent were studied, and a resin plugging agent system with excellent plugging performance was prepared. The formula is as follows: 25% urea formaldehyde resin +1% betaine +1% silane coupling agent KH-570 + 3% ammonium chloride +1% hexamethylenetetramine +1% sodium carboxymethyl cellulose. The optimal curing temperature is between 60 and 80 °C, with a controllable curing time of 1-3 h. Experimental studies examined the rheological and curing properties of the resin plugging agent system. The results showed that the viscosity of the high-strength curable resin system before curing remained stable with increasing shear rates. Additionally, the storage modulus and loss modulus of the resin solutions increased with shear stress, with the loss modulus being greater than the storage modulus, indicating a viscous fluid. The study also investigated the effect of different salt ion concentrations on the curing effect of the resin plugging system. The results showed that formation water containing Na+ at concentrations between 500 mg/L and 10,000 mg/L increased the resin's curing strength and reduced curing time. However, excessively high concentrations at lower temperatures reduced the curing strength. Formation water containing Ca2+ increased the curing time of the resin plugging system and significantly impacted the curing strength, reducing it to some extent. Moreover, the high-strength curable resin plugging agent system can effectively stay in various fracture types (parallel, wedge-shaped) and different fracture sizes, forming a high-strength consolidation under certain temperature conditions for effective plugging. In wedge-shaped fractures with a width of 10 mm, the breakthrough pressure of the high-strength curable resin plugging agent system reached 8.1 MPa. As the fracture width decreases, the breakthrough pressure increases, reaching 9.98 MPa in wedge-shaped fractures with an outlet fracture width of 3 mm, forming a high-strength plugging layer. This research provides new ideas and methods for solving drilling fluid loss in fractured loss zones and has certain application and promotion value.

Study on the influence of vertical stress difference coefficient on fracture characteristics of shale under high stress

AbstractTo study the effect of vertical stress difference coefficient on fracture characteristics of shale fracturing, high stress true triaxial hydraulic fracturing test was carried out. By analyzing the profile after fracturing, it was found that the area of hydraulic fracture increased with the increase of vertical stress difference coefficient, and the probability of shear fracture will increase when the stress difference coefficient was high. A high vertical stress differential coefficient exerts a strong control over the direction of crack propagation, while a low vertical stress difference coefficient is beneficial to improve the roughness of hydraulic fracture surface and promote the formation of complex fracture network. By analyzing the pump pressure curves of different tests, it was found that with the increase of vertical stress difference coefficient, the formation and expansion of hydraulic fractures were more difficult. The surface characteristics of hydraulic fractures were quantified based on three‐dimensional topography scanning technology, combined with fractal dimension and fracture area calculation method, the results showed that with the increase of vertical stress difference coefficient, the fractal dimension and fracture area decreased. Since shale is stratified, and the transformation of reservoir is mainly reflected in the enhancement of fracture complexity through tensile failure, Xsite discrete grid method was used to study the influence of fracture propagation behavior with different bedding strengths. The results showed that when the bedding tensile strength was high, hydraulic fractures were easy to pass through the bedding, and when the bedding tensile strength was low, hydraulic fractures were easy to be captured by natural fractures. In addition, tensile cracks were easy to form when the tensile strength of bedding was low, shear cracks were easy to form when the strength of bedding was high, and the fracture volume was larger when the strength of bedding was low. This study provides a theoretical basis for hydraulic fracturing in engineering.

Forensic medical determination of the age of fractures based on X-ray research methods: A literature review

Fractures of various locations as a result of traumatism rank second in both Russia and abroad. In Iran, and in the daily work of a forensic expert, skeletal trauma, if not prevalent, is one of the injuries encountered during the examination of victims, accused, and other persons. In addition to determining the mechanism of bone fracture formation, experts face cases of persistent injuries. Determining the time of the occurrence of bodily injuries in living persons generally does not involve special labor if full-fledged research objects are available. A much more difficult task is determining the age of a bone fracture from control radiographs, without primary clinical and radiological data, when the expert is provided with only control radiographs of the area of interest, which were taken after a long time has elapsed from the time of injury. In modern domestic and foreign scientific sources, no clear criteria have been established for determining the age of fractures based radiographs. Although some studies have been devoted to this issue in forensic medical literature, they are based on the results of nonradiological research methods: histological, histochemical, fractographic, ultrasound, and others. In the specialized literature on traumatology, determining the age of fractures since occurrence is not a priority. The analysis of literary sources shows the relevance of research on radiography methods for forensic medical practice.

The effect of constant electric field on the crack growth process of aluminum nanosheet using molecular dynamics simulation

Aluminum nanosheets are a form of Al nanoparticle that have been recently manufactured on an industrial scale and have a variety of uses. Al nanoparticles are extensively used in a variety of sectors, including aerospace, construction, medical, chemistry, and marine industries. Crack propagation in various constructions must be investigated thoroughly for structural design purposes. Cracks in nanoparticles may occur during the production of nanosheets (NSs) or when different mechanical or thermal pressures were applied. In this work, the effect of a continuous electric field on the fracture formation process of aluminum nanosheets was investigated. For this study, molecular dynamics simulation and LAMMPS software were used. The effects of various electric fields on several parameters, including as stress, velocity (Velo), and fracture length, were explored, and numerical data were retrieved using software. The results show that the amplitude of the electric field parameter affected the atomic development of modeled Al nanosheets throughout the fracture operation. This effect resulted in atomic resonance (amplitude) fluctuations, which affected the mean interatomic forces and led the temporal evolution of atoms to converge to certain specified initial conditions. The crack length in our modeled samples ranged from 22.88 to 32.63 Å, depending on the electric field parameter (0.1–1 V/Å). Finally, it was determined that the crack growth of modeled Al nanosheets may be controlled using CEF parameters in real-world situations.

Enhancing drilling efficiency: An experimental study on additives for mud loss mitigation in fractured media

Drilling in fractured formations poses a substantial challenge due to mud loss, which not only impedes operations but also leads to substantial costs and delays. Effectively controlling mud loss is crucial for efficient drilling. However, determining the appropriate mud additive to minimize mud loss in fractured formations requires further investigation. This is because proper mud additives can assist in sealing fractures, preventing wellbore instability issues and minimizing formation fluid influx. This study aims to investigate mud loss in fractured porous media by evaluating three additives' performance using an experimental setup that provides different fracture apertures. This setup provides an accurate simulation of down-hole static filtration at high pressure/temperature by flowing pressurized mud through fractured porous media and measuring effluent under different scenarios. The particular focus is on preformed particle gel (PPG), walnut shell, and shell additives. The study examines the effects of these additives, their particle sizes, and their mixture effect on mud loss. An optimal concentration of 8000 ppm of PPG, as well as larger particle sizes (mesh No.200) of walnut shell and shell, are found to be more effective in controlling mud loss, reducing mud loss by 34.4%, 110%, and 20.85%, respectively, compared to the base mud. The results reveal that when mud contains only one additive, the walnut shell is the most effective, reducing the volume of mud loss from 394.2 cc to 150.2 cc, while a mixture of PPG-shell-base mud at elevated temperatures represents the highest performance of additive combinations. The PPG-shell-base mud significantly reduces mud loss from 394.2 cc to 115 cc and 27.8 cc at 50 °C and 80 °C. In conclusion, this research not only contributes valuable insights to the field but also offers practical recommendations for the use of additives to effectively control mud loss during drilling operations in fractured formations, ultimately improving drilling efficiency and cost-effectiveness.

Особенности обрабатываемости резанием новых высокопрочных титановых сплавов с ультрамелкозернистой структурой для деталей авиационной техники

The results of experimental studies of the cutting parameters effect (cutting speed, feed, depth-of-cut) on the roughness of Ra, the microstructure of the surface layer of Ti-6Al-4V alloy samples with a conventional coarse-grained (CG) and ultrafine-grained (UFG) structure obtained by equal-channel angular pressing are presented. In framework of solving the problem connected with studying the machinability of a new VT6 alloy having an UFG structure, the development of a methodology for experimental research under turning was carried out. Physical parameters such as vibrations and noise under cutting, power consumption, numerical parameters of roughness, the magnitude and the pattern of residual stresses distribution and others are determined according to cutting modes and the tool used for the operation. It is shown that when turning at a low cutting speed, the roughness of CG sample is better than UFG of the alloy. With an increase in the cutting speed by 1,5 times, on the contrary, a sample with an UFG structure has a lower roughness Ra compared to a CG sample. Differences in the morphology and microstructure of the chips formed within comparative machining are discussed, taking into account types of microstructure of the alloy being treated, namely, presence of plastic flow lines in the chip microstructure after turning an UFG sample, the formation of large shifts, chips and tiny fractures in the chips after turning a CG alloy. It is found that new titanium alloys under turning obtain better cutting machinability in terms of such parameters as surface roughness, noise and vibration under cutting, and a more favorable character of residual stresses and riveting in the surface layer. Studying these factors, it is possible to predict a significant reduction of tool wear and stabilization of its durability compared to conventional coarse-grained titanium treatment.

A Morphological Method for Predicting Permeability in Fractured Tight Sandstone Reservoirs Based on Electrical Imaging Logging Porosity Spectrum

Summary Permeability is a crucial parameter in formation evaluation, which reflects reservoir fluid mobility and directly influences subsequent development and production. In conventional to tight sandstone formations without fractures, numerous methods have been developed to predict permeability. However, permeability prediction accuracy based on the current method is low in fractured tight sandstone reservoirs due to the influence of heterogeneity, and little research is focused on permeability evaluation in such reservoirs. Conventional wireline and nuclear magnetic resonance (NMR) logging lose their role in fracture parameter evaluation, whereas electrical imaging logging is available for reflecting fracture information. Hence, we adopt electrical imaging logging, instead of conventional wireline and NMR logging, to predict permeability in fractured tight sandstone reservoirs. In this study, we propose a morphological method for permeability prediction using electrical imaging logging. Initially, we process the electrical imaging logging data to obtain the porosity spectra and determine the peak of the primary porosity spectrum. We then extract the mean and standard deviation of the primary porosity spectrum based on its distribution morphology. Meanwhile, we also use the normal distribution function to fit the primary porosity spectrum and accumulate the amplitudes of the original and fitted porosity spectra, respectively. When the cumulative amplitude of the fitted spectra stabilizes, the corresponding porosity indicates the boundary between primary and secondary pores. This boundary allows us to calculate the proportion of primary pores to total pores. Permeability in fractured tight sandstone formations is influenced by both primary and secondary pores, showing a strong correlation with the proportion of primary porosity. Finally, we establish a permeability prediction model based on total porosity and the proportion of matrix pores. The reliability of our established permeability evaluation model is confirmed by comparing the predicted permeabilities with core-derived results in the Triassic Chang 63 Member of the Jiyuan area in the Ordos Basin. In unfractured formations, the predicted permeability based on our raised model closely matches the results derived solely from total porosity. In fractured formations, however, the calculated permeability using our proposed model aligns more closely with the core-derived result, while predictions based on current and NMR models tend to underestimate permeability.

Bond performance of reinforcing bars in fly ash-based engineered geopolymer composites under uniform and nonuniform corrosion conditions

While concrete is the most popular building material in the world, corrosion of the steel reinforcement in reinforced concrete (RC) structures poses ongoing durability issues. In this study, the effects of alkali activator modulus, concentration, and different corrosion periods are rigorously investigated utilizing accelerated electrochemical corrosion techniques under both uniform and nonuniform corrosion conditions. Bond stress and bond stress deterioration are evaluated to provide a thorough examination of corrosion-induced fracture formation through pull-out experiments. X-CT 3D imaging is also used to understand the spread of rust in both corrosion scenarios. Results show that mixes with lower alkali activator modulus and higher alkali activator concentration might result in better bond stress preservation and higher ultimate bond stress under corrosion. High bond stress, however, usually corresponds to a more brittle failure when subjected to pull-out force. Nonuniform corrosion treatment can result in differential rust formation and a quicker bond breakdown between steel bars and engineered geopolymer composites (EGCs) than uniform corrosion. Furthermore, under corrosion, EGCs with high alkali activator modulus tend to form more penetrating cracks with limited width and depth. Both narrow and deep penetrating fractures can arise from EGCs with low alkali activator concentration.

A Study on Three-Dimensional Multi-Cluster Fracturing Simulation under the Influence of Natural Fractures

Multi-cluster fracturing has emerged as an effective technique for enhancing the productivity of deep shale reservoirs. The presence of natural bedding planes in these reservoirs plays a significant role in shaping the evolution and development of multi-cluster hydraulic fractures. Therefore, conducting detailed research on the propagation mechanisms of multi-cluster hydraulic fractures in deep shale formations is crucial for optimizing reservoir transformation efficiency and achieving effective development outcomes. This study employs the finite discrete element method (FDEM) to construct a comprehensive three-dimensional simulation model of multi-cluster fracturing, considering the number of natural fractures present and the geo-mechanical characteristics of a target block. The propagation of hydraulic fractures is investigated in response to the number of natural fractures and the design of the multi-cluster fracturing operations. The simulation results show that, consistent with previous research on fracturing in shale oil and gas reservoirs, an increase in the number of fracturing clusters and natural fractures leads to a larger total area covered by artificial fractures and the development of more intricate fracture patterns. Furthermore, the present study highlights that an escalation in the number of fracturing clusters results in a notable reduction in the balanced expansion of the double wings of the main fracture within the reservoir. Instead, the effects of natural fractures, geo-stress, and other factors contribute to enhanced phenomena such as single-wing expansion, bifurcation, and the bending of different main fractures, facilitating the creation of complex artificial fracture networks. It is important to note that the presence of natural fractures can also significantly alter the failure mode of artificial fractures, potentially resulting in the formation of small opening shear fractures that necessitate careful evaluation of the overall renovation impact. Moreover, this study demonstrates that even in comparison to single-cluster fracturing, the presence of 40 natural main fractures in the region can lead to the development of multiple branching main fractures. This finding underscores the importance of considering natural fractures in deep reservoir fracturing operations. In conclusion, the findings of this study offer valuable insights for optimizing deep reservoir fracturing processes in scenarios where natural fractures play a vital role in shaping fracture development.

Experimental Study on Proppant Migration in Fractures Following Hydraulic Fracturing

Complex fracture technology is key to the successful development of unconventional oil and gas reservoirs, such as shale. Most current studies focus on how to improve the complexity of the fracture network. It is still unclear whether proppant can enter the branch fractures at all levels after the formation of complex fractures. The effects of construction displacement, proppant particle size, proppant density, fracturing fluid viscosity, sand ratio, and other factors on proppant migration in single fractures and complex fractures were studied using an experimental device independently developed by the laboratory. The results show that the lowest point height of the sandbank and the equilibrium height of the sandbank are directly proportional to the particle concentration and density, respectively, and inversely proportional to the displacement and fracturing fluid viscosity. The equilibrium time of the sandbank is inversely proportional to the displacement, particle concentration, and density, respectively, and proportional to the viscosity of the fracturing fluid. Under the same experimental conditions, the larger the branch angle, the smaller the height of the main/secondary fracture sandbank. In the design of the fracturing process, fracturing fluid with varying viscosities and proppant with different densities should be selected according to the formation conditions and fracturing targets. In the face of long fracture lengths, the combination of low-viscosity fracturing fluid with an appropriate viscosity and low-density proppant can meet the goal of placing proppant over long distances and effectively supporting fractures over extended lengths. Subsequently, high-density proppant or reduced construction displacement are adopted to usefully support fractures in the near-wellbore area. The results of this paper can provide theoretical support for proppant selection and fracturing program design.

Development of Hybrid Electrospun Nanofibers: Improving Effects of Cellulose Nanofibers (CNFs) on Electrospinnability of Gelatin.

Cellulose nanofibers (CNFs) were used to improve the electrospinnability of the gelatin protein in a water/ethanol/acetic acid (3:2:3, v/v) solution. The effects of different concentrations of CNFs (0.5-4%) on the important physical properties of the gelatin solution (15%), including rheology, conductivity, and surface tension, were investigated. The apparent viscosity and shear-thinning behavior were increased by increasing the CNF concentration from 0 to 4% at a low shear rate (<10 s-1). CNFs also increased the electrical conductivity and surface tension of the gelatin solution. Scanning electron microscopy (SEM) images revealed uniformly ordered structures with good continuity without fracture or bead formation in all hybrid nanofibers. They also showed that the average diameters of fibers decreased from 216 nm in the pure gelatin nanofibers to 175.39 nm in the hybrid gelatin/CNF (4%) ones. Differential scanning calorimetry (DSC) results showed that CNFs increased Tg, and X-ray diffraction (XRD) analysis showed that the electrospinning process caused the formation of more amorphous structures in the gelatin/CNF hybrid nanofibers. The tensile test indicated that by adding 2% CNFs, the ultimate tensile strength (UTS) and strain at break (SB) of nanofiber mats increased from 4.26 to 10.5 MPa and 3.3% to 6.25%, respectively. The current study indicated that incorporating CNFs at the optimal concentration into a gelatin solution can improve the resulting hybrid nanofibers' morphology, average diameter, and mechanical properties.

Peridynamic‐based modeling of elastoplasticity and fracture dynamics

AbstractThis paper introduces a particle‐based framework for simulating the behavior of elastoplastic materials and the formation of fractures, grounded in Peridynamic theory. Traditional approaches, such as the Finite Element Method (FEM) and Smoothed Particle Hydrodynamics (SPH), to modeling elastic materials have primarily relied on discretization techniques and continuous constitutive model. However, accurately capturing fracture and crack development in elastoplastic materials poses significant challenges for these conventional models. Our approach integrates a Peridynamic‐based elastic model with a density constraint, enhancing stability and realism. We adopt the Von Mises yield criterion and a bond stretch criterion to simulate plastic deformation and fracture formation, respectively. The proposed method stabilizes the elastic model through a density‐based position constraint, while plasticity is modeled using the Von Mises yield criterion within the bond of particle paris. Fracturing and the generation of fine fragments are facilitated by the fracture criterion and the application of complementarity operations to the inter‐particle connections. Our experimental results demonstrate the efficacy of our framework in realistically depicting a wide range of material behaviors, including elasticity, plasticity, and fracturing, across various scenarios.

Impact fracturing of rock-like material using carbon dioxide under different temperatures and pressures

Unconventional resources (oil, gas, and geothermal) are often buried deep underground within dense rock strata and complex geological structures, making it increasingly difficult to create volumetric fractures through conventional hydraulic fracturing. This paper introduces a novel method of supercritical energetic fluid thermal shock fracturing. It pioneers a CO2 deflagration impact triaxial pneumatic fracturing experimental system, using high-strength similar materials to simulate deep, hard rock masses. The study investigates the rock-breaking process and crack propagation patterns under supercritical CO2 thermal shock, revealing and discussing the types of thermal shock-induced fractures, their formation conditions, and discrimination criteria. The research indicates that higher supercritical CO2 thermal shock pressures and faster pressure release rates facilitate the formation of radial branching fractures, circumferential cracks, and branch cracks. Typically, CO2 thermal shock generates 3–5 radial main cracks, which is significantly more than the single main crack formed by hydraulic fracturing. The formation of branched cracks is often caused by compression-shear failure and occurs under relatively harsh conditions, determined by the confining pressure, rock properties, peak thermal shock pressure, and the pressure sustained post-decompression. The findings are expected to offer a safe, efficient, and controllable shockwave method of supercritical fluid thermal shock fracturing for the exploitation of deep unconventional oil and gas resources.

The Priority Areas for Groundwater Utilization in Fractured Rock Formation, Pangandaran Regency

Abstract Pangandaran Regency is one of the best tourist destinations in West Java; many tourist attractions and regional developments to facilitate visiting tourists increase the need for water. However, in some areas of Pangandaran Regency, it is included in the rare groundwater zone according to its aquifer productivity, especially in the fracture rock formation, so it is necessary to conduct research related to the presence of groundwater in the area. This study aims to determine priority areas for the development of groundwater utilization in fractured rock formations located in the Pangandaran Regency. The fracture rock formations in Pangandaran Regency are located from the northwest to the southeast; on the regional geological map, the formation’s name is the Jampang Formation. This study used the Groundwater Potential Index (GPI) method to determine groundwater potential and the Analytic Hierarchy Process (AHP) method to determine water utilization area levels. The parameters used are fracture (F), lithology (L), drainage (D), topography (T), rainfall (R), water usage, land use, and population distribution. This research shows that areas with rare groundwater zones still have groundwater potential that can be developed to meet water needs. There are five priority area classifications: very high is 19 km2, high is 17.92 km2, medium is 67.90 km2, low is 70.99 km2, and very low is 162.40 km2.

Quartz Dissolution Effects on Flow Channelization and Transport Behavior in Three‐Dimensional Fracture Networks

AbstractWe perform a set of reactive transport simulations in three‐dimensional fracture networks to characterize the impact of geochemical reactions on flow channelization. Flow channelization, a frequently observed phenomenon in porous and fractured subsurface rock formations, results from the spatially variable hydraulic resistance offered by a geological structure. In addition to geo‐structural features such as network connectivity, geometry, and hydraulic resistance, geochemical reactions, for example, dissolution and precipitation, can dynamically inhibit or enhance flow channelization. These geochemical processes can change the fracture permeability leading to increased flow channelization, which are localized connected regions of high volumetric flow rates that are seemingly ubiquitous in the subsurface. In our simulations, fractures partially filled with quartz are gradually dissolved until quasi‐steady state conditions are obtained. We compare the flow field's initial unreacted and final dissolved states in terms of flow and transport observations. We observe that the dissolved fracture networks provide less resistance to flow and exhibit increased flow channelization when compared to their unreacted counterparts. However, there is substantial variability in the magnitude of these changes which implies that the channelization strongly depends on the network structure. In turn, we identify the interplay between the particular network structure and the impact of geochemical dissolution on flow channelization. The presented results indicate that geological systems that have been weathering or reactive for longer times in older landscapes are likely to have increased flow channelization compared to their equivalent but younger counterparts, which implies a time dependence on flow channelization in fractured media.

Development characteristics and controlling mechanism of different microfracture combinations in shale reservoir: A case study of silurian longmaxi formation in Weiyuan area

Fractures in organic-rich shale are important reservoir spaces and seepage channels of shale gas, and they are closely related to the gas-bearing properties of shale. The development characteristics and laws of fractures are of great significance in the exploration and development of shale oil and gas. This study examines organic-rich shales of the Wufeng–Longmaxi Formation in the Weiyuan area of the Sichuan Basin. On the basis of two-dimensional large-area multi-scale combination electron microscopy characterization and digital core platform technology, the development degree and distribution of different fractures are quantitatively characterized. The results show the following. (1) The shale of the Wufeng and Longmaxi formations developed a variety of fractures with different occurrences, sizes, and origins. According to the number and combination relationship between fractures of different occurrences, the shale can be divided into four fracture combination types: horizontal bedding fractures; vein fractures; reticular fractures; and ring fractures. Of these, the horizontal bedding fracture group has the largest number of samples and a higher average fracture surface porosity. (2) The degree of fracture development in the shale is affected by many factors, such as the laminar type, mineral composition, mineral particle size, mineral distribution, and total organic carbon, and the controlling mechanisms of different fracture combination types differ. Factors such as horizontal stratification, high clay mineral content, and uneven mineral particle size are conducive to the development of horizontal bedding joints. (3) Differences in the sedimentary environment affect the variation laws of the vertical fracture combination types and density. The total organic carbon and organic quartz content of the Long111 layer with deeper sedimentary water is higher, and the vein fracture formation is more developed than in other small layers, while the clay mineral content of the Long112 and Long114 layers with shallower sedimentary water is higher and the horizontal layer is more developed; the fracture combination type is dominated by the horizontal bedding fracture combination. At the same time, the fractures at the junction of each layer of the Long11 sub-member are the most developed because sea level rise and fall make the mineral particle size heterogeneity most prominent at the junction of the small layer.

Geophysical Investigation of Bulding Distress in Gashua, Nigeria

Gashua is the Headquarter of Bade local government in Yobe State, it has a population of about 125, 000 according to the 2006 population census. It is a densely populated town located in a flood plain within the Chad Basin. In an attempt to proffer solutions to the prevailing building distress in Gashua and its environs, this study was carried out to accurately characterize the subsurface geology of the area, thereby reducing the incidence of building failure in the area to minimum. In this study, electrical resistivity method was used to determine the causes of building distress and failure in Gashua and its environs. Vertical Electrical Sounding (VES) using Schlumberger array and Electrical Resistivity Tomography (ERT) were adopted for the study. The results of the VES survey showed that the area is composed of five geologic layers which are; the topsoil, clay, sand, sandy-clay, and sand. The ERT results showed that most of the building foundations in the study area were laid within the second layer which is a clay formation. The findings of this study showed that the building distress and failure which are common in the study area were caused by the volumetric changes of the clay formation due to hydrological dynamics. The clay formation absorbs water during the raining season and swells up, and during the dry season it shrinks, this changes in the volume of the clay formation underlying the building foundation in the study area induces a significant mechanical stress on the buildings leading to the formation of cracks, voids, fissures and fracturing of the buildings, which eventually culminate into collapse. In this study, electrical resistivity method of geophysical investigation has demonstrated to be a veritable tool for geotechnical soil evaluation. Based on the findings of this study, geophysical investigation of a proposed site...

Finite–Discrete Element Method Simulation Study on Development of Water-Conducting Fractures in Fault-Bearing Roof under Repeated Mining of Extra-Thick Coal Seams

The formation of water-conducting fractures in overlying strata caused by underground coal mining not only leads to roof water inrush disasters, but also water-conducting fractures penetrate the aquifer, resulting in the occurrence of a mine-water-inrush disaster and the loss of water resources. It destroys the sustainability of surface water and underground aquifers. This phenomenon is particularly significant in extra-thick coal seams and fault-bearing areas. Numerical simulation is an effective method to predict the failure range of mining overburden rock with low cost and high efficiency. The key to its accuracy lies in a reasonable constitutive model and simulation program. In this study, considering that the three parts of penetrating cracks, non-penetrating cracks, and intact rock blocks are often formed after rock failure, the contact state criterion and shear friction relationship of discrete rock blocks and the mixed fracture displacement–damage–load relationship are established, respectively. Combined with the Mohr–Coulomb criterion, the constitutive model of mining rock mass deformation–discrete block motion and interaction is formed. On this basis, according to the engineering geological conditions of Yushupo Coal Mine, a numerical model for the development of water-conducting cracks in the roof with faults under repeated mining of extra-thick coal seams is established. The results show the following: The constitutive relation of the continuous deformation–discrete block interaction of overlying strata and the corresponding finite element–discrete element FDEM numerical program and VUSDFLD multi-coal seam continuous mining subroutine can numerically realize the formation process of faults and water flowing fractures in overlying strata under continuous mining of extra-thick multi-coal seams. The toughness of sand mudstone is low, and the fracture will be further developed under the repeated disturbance of multi-thick coal seam mining. Finally, it is stabilized at 216–226 m, and the ratio of fracture height to mining thickness is 14.1. When the working face advances to the fault, the stress concentration occurs in the fault and its overlying rock, which leads to the local fracture of the roof rock mass and the formation of cracks. The fault group makes this phenomenon more obvious. The results have been preliminarily applied and tested in Ningwu mining area, which provides theoretical support for further development of roof water disaster control under the condition of an extra-thick coal seam and avoids the loss of water resources in surface water and underground aquifers.

Numerical Simulation Study on the Influence of Fracture on Borehole Wave Modes: Insights from Fracture Width, Filling Condition, and Acoustic Frequency.

Unconventional reservoirs, such as shale and tight formations, have become increasingly vital contributors to oil and gas production. In these reservoirs, fractures serve as crucial spaces for fluid migration and storage, making their precise assessment essential. Array acoustic logging stands out as a pivotal method for evaluating fractures. To investigate the impact of fracture width, fracture-filling conditions, and acoustic frequency on compressional and shear waves, a three-dimensional variable mesh finite difference program was employed for acoustic logging numerical simulation. Firstly, numerical models representing fractured formations with varying fracture widths and distinct fluid-filling conditions were established, and array acoustic logging numerical simulations were conducted at different frequencies. Subsequently, the waveform data were processed to extract acoustic characteristic parameters, such as velocities and amplitude attenuations of compressional and shear waves. Finally, a quantitative analysis was conducted to examine the variation patterns of characteristic parameters of refracted compressional and shear waves in relation to fracture properties. The research results indicate that amplitude attenuation information derived from borehole wave modes is particularly sensitive to the changes in fracture properties. As fracture width increased, we observed a significant amplitude attenuation in both compressional and shear waves, proportional to the logarithm of the attenuation coefficients. Furthermore, when the fracture width was constant, gas-filled fractures exhibited more prominent amplitude attenuation than water-filled fractures, with shear wave attenuation being more sensitive to the filling material. Moreover, from a quantitative perspective, the analysis revealed that the attenuation coefficients of refracted compressional and shear waves exhibited an exponential variation with gas saturation. Notably, once fracture width and filling conditions were established, the amplitudes of compressional and shear waves at the dominant frequency of 40 kHz were significantly reduced compared to those at 8 kHz, accompanied by increased attenuation. Subsequent quantitative analysis revealed that, when the product of fracture width and dominant frequency remains constant, the corresponding attenuation coefficient ratios approach 1. This indicates that the attenuation process of acoustic propagation in fractured media follows the principle of acoustic similarity. The findings of this study provide reference for further research on fracture property evaluation methods based on array acoustic logging data.