Exchange Performance Research Articles

Greywater heat recovery to the refill water of a dishwasher via paraffin wax and steel wool aided segmental baffle heat exchanger

In this study, the recovery of household dishwasher greywater thermal energy into dishwashing water using paraffin wax and steel wool supported segmental heat exchanger was experimentally investigated. The heat exchange performance was 40% in rapid, economy, and intensive modes and the heat recovery was 0.048, 0.031 and 0.082 kWh, respectively. Efficiency increased by 5.01%, 3.84%, and 6.5%. Time and energy were saved, and hygienic washing was accomplished by raising the washing temperature and reducing the cycle time nearly 97, 113, and 240 s. It is estimated that by using heat exchangers on 16,954,196 dishwashers in use in Turkey, small, medium, and large families can save an average of 127.366, 254.733 and 509.466 GWh per year, respectively, provided they use the three dishwasher modes equally. The annual economic size of the gain and its contribution to emission reduction in CO2 equivalents are $15.793 million, $31.586 million, $63.173 million and 112.974 kt, 225.948 kt, 451.897 kt, respectively. Energy efficiency index of dishwasher increased from 48.84 to 46.97.

Research on mine heat exchange system and its heat exchange performance prediction

As a clean and renewable energy source, mine geothermal energy holds immense potential for application. To better utilize this resource, a buried tube ground-source heat pump system has been proposed for mine geothermal energy development. A mathematical model for the mine geothermal heat exchange system has been established. Firstly, the experiment of constant heat flow and heat transfer is conducted to verify the applicability of the mathematical model and to explore the temperature response law of single pipe fluid and rock and soil. Subsequently, the influence of ten single-tube factors on the heat transfer performance of the mine geothermal heat exchange system is studied using the single-factor analysis method. The sensitivity of the single tube factor is analyzed using the range analysis method to obtain six main factors. The impact of the group tube and time factors on the heat transfer performance is qualitatively analyzed. Finally, the orthogonal experiment and the non-linear regression method are employed to derive a prediction expression for the average output temperature of the mine geothermal heat exchange system by considering the single tube, group tube, and time factors. The research results enable the quantitative prediction of heat exchange performance and guide the design and optimization of mine geothermal heat exchange systems.

Gas exchange optimization in aircraft engines using sustainable aviation fuel: A design of experiment and genetic algorithm approach

The poppet valves two-stroke (PV2S) aircraft engine fueled with sustainable aviation fuel is a promising option for general aviation and unmanned aerial vehicle propulsion due to its high power-to-weight ratio, uniform torque output, and flexible valve timings. However, its high-altitude gas exchange performance remains unexplored, presenting new opportunities for optimization through artificial intelligence (AI) technology. This study uses validated 1D + 3D models to evaluate the high-altitude gas exchange performance of PV2S aircraft engines. The valve timings of the PV2S engine exhibit considerable flexibility, thus the Latin hypercube design of experiments (DoE) methodology is employed to fit a response surface model. A genetic algorithm (GA) is applied to iteratively optimize valve timings for varying altitudes. The optimization process reveals that increasing the intake duration while decreasing the exhaust duration and valve overlap angles can significantly enhance high-altitude gas exchange performance. The optimal valve overlap angle emerged as 93 °CA at sea level and 82 °CA at 4000 m altitude. The effects of operating parameters, including engine speed, load, and exhaust back pressure, on the gas exchange process at varying altitudes are further investigated. The higher engine speed increases trapping efficiency but decreases the delivery ratio and charging efficiency at various altitudes. This effect is especially pronounced at elevated altitudes. The increase in exhaust back pressure will significantly reduce the delivery ratio and increase the trapping efficiency. This study demonstrates that integrating DoE with AI algorithms can enhance the high-altitude performance of aircraft engines, serving as a valuable reference for further optimization efforts.

Evaluation of Trend of Foreign Exchange Reserve and Shipping Industry Trade Performance in Nigeria

This study focused on evaluation of the trend of Foreign Exchange Reserve (FX) and performance of shipping industry trade through examining the export and import trades within the periods 2011 to 2022. The objectives were to determine the correlation between trend values of FX with export and import shipping trades in Nigeria. Provisional data on Foreign Exchange Reserve, export and import trades from World Bank, CBN and Trend Economy were analyzed using spearman’s rank correlation coefficient analysis and it was observed that Foreign Exchange positively influences export and import shipping trades, however, the study infers that the impacts were not significant at 0.05 (2-tailed) Significance level. It concludes that the positive correlations between the data variables informs that decrease in FX influences decrease in export and import trade which also retar economic growth, development and reduced people’s standards of living in Nigeria. However, the reserve becomes the case. The study recommends immediate policy adjustment to hold and maintain strong Foreign Exchange which could boost country’s reserve for better performance of the shipping industry and other sectors of the economy.

Heat Transfer Performance and Operation Scheme of the Deeply Buried Pipe Energy Pile Group

This paper describes a study on the heat transfer properties of the deeply buried pipeline energy pile group, which is an efficient and convenient geothermal development technology. Through in situ experiments and a simulation algorithm, the research investigated the heat transmission characteristics of the deeply buried pipe energy pile group and optimized different intermittent operation schemes. The findings suggest that prolonged operation of the pile cluster intensifies heat buildup within the pile foundation, thereby adversely affecting the system’s overall heat exchange efficiency. Employing an intermittent operating mode can alleviate this heat accumulation phenomenon, thereby promoting sustained heat exchange performance of the piles over time. To evaluate the comprehensive thermal interaction and energy efficiency ratio of the energy pile heat exchange system, various intermittent operation strategies were compared in the study. Among them, the intermittent operational scheme with a ratio of n = 5 was found to be optimal, with the total average heat transfer rate of the pile set only 0.51% lower than that of the continuous operational mode, but the overall energy efficiency ratio improved by 19.6%. The intermittent operational mode proposed in this study can achieve the goal of saving energy and efficiently extracting geothermal resources, providing theoretical guidance for the extraction and utilization of subsurface geothermal power by energy piles.

Assessing the Mediating Effect of Team-Member Exchange on the Relationship between Transformational Leadership and Performance of People with Disabilities: A Study of Hong Kong Employers of People with Disabilities

Purpose—This study aims to examine the links between transformational leadership, team-member exchange and job performance of people with disabilities in Hong Kong. Design/methodology/approach—Data were collected from a sample of 108 direct supervisors of people with disabilities via an online survey with validated scales. The structural equation modelling approach via SmartPLS (Version 3.0) was used to investigate the linear relations and the mediated effect amongst the variables. Findings—Transformational leadership was positively related to team-member exchange (p = 0.013), but its link with job performance was insignificant (p ≥ 0.05). Team-member exchange was positively related to job performance (p = 0.000). Hence, team-member exchange fully mediated the relationship between leaders’ transformational leadership and the job performance of people with disabilities. Originality/value—Transformational leadership is favorable for the job performance of people with disabilities, but its influence is indirect. High level of team-member exchange quality is necessary, as team-member exchange fully mediates the relationship between transformational leadership and the job performance of people with disabilities. Managers should demonstrate transformational leadership to all employees and not only pay attention to people with disabilities. This insight helps drive workplace disability inclusion.

Synthesis of Low-Silicon X-Type Zeolite from Lithium Slag and Its Fast Exchange Performance of Calcium and Magnesium Ions.

Without the addition of silicon and aluminum sources, a pure-phase KNaLSX zeolite was successfully synthesized from the residue (lithium slag), which was produced from spodumene in the production process of lithium carbonate. The KNaLSX samples were characterized by an X-ray Diffractometer (XRD), Scanning Electron Microscope (SEM), X-ray Fluorescence Spectrometer (XRF), Thermogravimetric Differential Thermal Analysis (TG-DTA), Fourier Transform Infrared Spectrometer (FT-IR), and N2 adsorption measurement. The ion exchange capacity and the ion exchange rate of calcium and magnesium ions were measured as used for a detergent builder, and the results were compared with the standard zeolites (KNaLSX and 4A). The experimental results show that the pure-phase KNaLSX synthSynthesis and characterization of co-crystalline zeolite composite of LSX/esized from lithium slag has a SiO2/Al2O3 ratio of 2.01 with a grain size of 3~4 μm, which is close to the commercial KNaLSX sample of a SiO2/Al2O3 ratio of 2.0. The BET-specific surface area of KNaLSX is 715 m2/g, which is larger than the low-silicon X-type zeolite (LSX) synthesized from waste residue reported in the literature. The ion exchange rate constant of calcium and magnesium ions in KNaLSX is 5 times and 3 times that of 4A zeolite, respectively. KNaLSX also has a high ion exchange capacity for magnesium ion of 191 mgMgCO3/g, which is 2 times than that of 4A zeolite, and a high ion exchange capacity for calcium ion of 302 mgCaCO3/g, which meets the first-grade standard of zeolite for detergent builders in China. The work provides the basis for high-value resource utilization of lithium slag and the development of a detergent builder for rapid washing.

Analysis of the effect of jet channel structure on the temperature uniformity of tempered glass

The air jet nozzle structure has a significant impact on the heat transfer uniformity and cooling rate of glass during the glass tempering process, and there is a lack of research on the discrepancy of different jet structures. The effects of double air knife, single air knife structures, and air hole structures on the cooling performance of glass in air-cooled tempering were investigated using numerical simulation and simplified analytical models. The calculated results are in agreement with the experimental results. The results show that the DK structure has a significant effect on improving the overall heat exchange performance of the glass, with lower surface temperatures for the same quenching time. The temperature inhomogeneities of DK, SK, and AH structures in the glass axial direction were 2.09%, 2.53%, and 3.33%, respectively, and the heat transfer uniformity of the DK structure was significantly better than the latter two. In comparison to the AH structure, the average heat transfer coefficients of the DK and SK structures increased by approximately 17.82% and 8.13%, respectively, while the heat transfer rates increased by approximately 7.05% and 4.51%. The study further improves the insufficiency of glass tempering research and provides theoretical guidance for the actual production of tempered glass.

A novel data-driven approach for coal-fired boiler under deep peak shaving to predict and optimize NOx emission and heat exchange performance

Coal-fired boilers considering deep peak shaving operate under wide and variable load requirements with complex and varying working conditions, making the prediction and optimization of combustion target variables challenging. This study proposed a data-driven approach for the prediction model building, tuning and combustion optimization. In this approach, a neural network for prediction based on Gaussian kernel and long short-term memory (LSTM), which captured and fused the working condition and temporal information, was first proposed. To address incomplete historical data coverage of working conditions, a fine-tuning framework with the idea of transfer and few-shot tuning was then introduced. Finally, an improved fitness function considering both optimization objectives and combustion adjustment limitations was designed to mitigate the risks associated with large-scale adjustments of operable variables. By conducting experiments on a 1000 MW boiler, targeting NOx concentration and the outlet temperature of the air pre-heater, the proposed method demonstrated high prediction accuracy with R2 values of 0.979 and 0.989, and significantly reduced mean squared error (MSE) by 98.05% and 97.37% on new conditions compared to untuned models. It achieved the reductions in NOx and temperature of 24.70 mgm−3 and 2.013 ∘C, and decreased the average changes of operable variables by 9.66% and 11.24% compared to using only rigid constraints.

Study on the optimization of heating exchanger in electric heating solid energy storage heating system

This paper addresses prevalent issues of suboptimal compatibility between the heating exchanger and the thermal storage unit, poor safety performance, and overall insufficient heat exchange efficiency within the application of heating exchangers in electric heating solid energy storage heating systems. Experimental testing and numerical simulation studies were conducted. The research investigates the effect of the temperature of inlet air as well as velocity on the heat exchange performance of the heating exchanger as well as temperature variations of single-row heat pipes. Drawing upon these change patterns, an optimized heating exchanger structure is proposed and subsequently investigated through optimization simulation studies. The study results indicate that the best overall optimization effect is achieved with a heating exchanger arranged with finned tube combinations of 4 mm in two rows, 6 mm in two rows, 8 mm in two rows, 10 mm in two rows, 12 mm in two rows, and 14 mm in ten rows arranged successively from front to back. When the heating exchanger’s inlet air speed is relatively high, this combination’s heat exchange capacity surpasses the original structure. Additionally, the uniformity of air-side temperature drop improved by 44.89%, while the finned area was reduced by 25.62%.

Examining the influence of number of inlets and outlets on the topology optimization design of battery liquid cooling plate

The trade-off between enhancing the thermal performance of battery liquid cooling plates and reducing their pumping power consumption remains an unresolved issue. In order to solve this problem, this study proposes a multi-inlet and multi-outlet liquid cooling plate design method based on topology optimization. Through topology optimization, 2D models with various numbers of inlets and outlets under different arrangements were obtained, and were extended into 3D numerical models. The study investigated the impact of inlet and outlet arrangement direction, quantity, channel depth, and total mass flow rate at the inlet on the performance of liquid cooling plates. The findings indicated that Topology-optimized liquid cooling plates exhibit superior flow and heat exchange performance compared to traditional straight-channel liquid cooling plates. Arranging the inlet and outlet along the width direction of the rectangular liquid cooling plate can reduce the pressure drop. As for the number of inlets and outlets along the width direction, employing three inlets and three outlets, as opposed to a single inlet and outlet, reduced pump power by 29.04 %, increased the heat transfer coefficient by 28.41 %, increased temperature uniformity by 39.13 %, and boosted the comprehensive evaluation factor by 80.7 %. Furthermore, the channel depth of 3 mm, with a total mass flow rate of 15 g/s at the inlet, was the ideal choice for achieving a balance between system heat dissipation and power consumption. Finally, the accuracy of the simulation was validated through experiments.

Facilitating Interfirm Collaboration by Using Social Media

ABSTRACT Purpose Using social media (SM) in the workplace is controversial. Managers are concerned about boundary spanners’ heavy use of SM for unproductive activities, while boundary spanners need task-focused SM usage to enhance cooperative intention, share mutual knowledge, and build long-term relations. To clarify the effects of SM usage, the authors draw on task–technology fit (TTF) theory to examine how task-focused SM usage (TSM) and relationship-focused SM usage (RSM) influence the efficacy of interpersonal guanxi in China’s emerging economy. Methodology/approach The authors test the proposed theoretical model by collecting 550 valid questionnaires of survey data from manufacturers in China. Ordinary least squares regression is used to analyze the data and test the hypotheses. Findings The results of the statistical analysis show that interpersonal guanxi improves interfirm coordination and exchange performance. Furthermore, TSM usage strengthens the positive impact of interpersonal guanxi on interfirm coordination but weakens the positive effect of interpersonal guanxi on exchange performance, while RSM usage enhances its positive impact on exchange performance but weakens the positive effect of interpersonal guanxi on interfirm coordination. Research implications This study contributes to the literature by developing and testing the TTF-based framework of interpersonal guanxi and SM usage. The finding enriches our knowledge on the roles of interpersonal guanxi in the business-to-business (B2B) context. Practical implications This study offers the guidance for firms using SM in the B2B context. SM usage should be fited with firms’ and boundary spanners’ tasks, considering the complementary and supplementary nature of SM usage. Originality/value/contribution This study tests the different roles of SM usage, i.e., TSM versus RSM, in fostering the efficacy of interpersonal guanxi, providing a meaningful perspective on firms’ knowledge activities. Moreover, by proposing a TTF-based framework of interpersonal guanxi and SM usage, it explores the informational roles of boundary spanners’ SM usage in promoting dyadic relationships.

Numerical study flow and heat transfer characteristics of superhydrophobic single tube bundle surface and wake flow

Regarding the design optimization of the heat exchanger, the traditional method of changing the size of the macroscopic structure can no longer meet the increasing demand for heat exchange performance. The superhydrophobic surface can significantly reduce the flow resistance, which is expected to be a new method for the optimal design of heat exchanger. However, when the superhydrophobic effect is applied to a specific type of heat exchanger, its flow and heat transfer performance is not clear. In this paper, the flow and heat transfer model of the traversing superhydrophobic tube bundle is studied. Combined with the FLUENT 18.0 software, the slip boundary conditions of the superhydrophobic surface are deduced, and the flow and heat transfer characteristics of the superhydrophobic tube bundle surface and the wake are numerically analyzed, the influence mechanisms of slip effect on flow and heat transfer characteristics were obtained. Overall, as Ls increases, the comprehensive Nu, also known as heat transfer performance, on the cylindrical surface gradually increases, while the comprehensive Cf, also known as frictional resistance, on the cylindrical surface gradually decreases, indicating that superhydrophobic performance is expected to achieve heat transfer enhancement. The above conclusions can provide a theoretical basis for the optimal design of high-efficiency compact heat exchanger, and have important engineering application significance.

Heat exchange performance of an energy-pile group in a hybrid GSHP system and effects of pile spacing

In long-term operations, seasonal imbalance in the thermal load may adversely affect the heat transfer performance of the energy piles, potentially resulting in thermal accumulation within the ground and eventual system failure. The heat transfer performance of energy pile systems during long-term operation under unbalanced thermal loads must be investigated. Moreover, the design parameters of energy piles are usually constrained by the requirements of foundation structural design, resulting in energy piles being densely arranged. Hence, the influence of pile spacing on the heat exchange performence of energy piles must be comprehensively understood. In this study, two- and three-dimensional energy-pile heat transfer models were established and innovatively coupled based on an engineering project currently under design. Numerical simulations were performed to investigate the heat transfer behavior of energy-pile groups subjected to unbalanced thermal loads and the effect of pile spacing on their heat exchange performance. Furthermore, design recommendations regarding the determination of the proportion of thermal loads to be borne by the energy piles in a hybrid GSHP system were provided. The results indicate that the proposed 2D-3D coupled modeling approach is able to simulate the heat exchange performance of large-scale energy pile groups. Pile spacing considerably affects the long-term thermal performance of energy-pile groups, especially in cases with small pile spacings. The influence of pile spacing on the heat exchange capacity of energy piles can be considered in the design phase by incorporating a group effect coefficient η, which are calculated to be 0.165, 0.470, 0.732, and 1 for pile spacings of 2 m, 4 m, 6 m, and 10 m, respectively.

Enhanced electrocatalytic activity of SrFe0.9Nb0.1O3-δ through in-situ synthesis of Sr3Fe1.8Nb0.2O7-δ coating

The influence of the heterogeneous interface is critical for the catalytic activity of the oxygen reduction reaction (ORR). This study demonstrates an enhancement of the electrocatalytic activity of the SrFe0.9Nb0.1O3-δ (SFN113) electrode through the construction of a SrFe0.9Nb0.1O3-δ-Sr3Fe1.8Nb0.2O7-δ (SFN113-SFN327) heterogeneous interface. By coating varying amounts of Sr(NO3)2 (0.1 g, 0.2 g and 0.3 g) on SFN113 (1 g), SFN113/327 composite electrodes with different amounts of triple conducting oxide SFN327 are in-situ synthesized by high temperature calcination. Electrical Conductivity Relaxation (ECR) tests show that SFN327 has superior oxygen surface exchange performance compared to SFN113, especially at lower temperatures. At 550 °C, the oxygen surface exchange parameter of SFN327 is 4.23 times higher than that of SFN113. Symmetric cell tests with SFN113/327||BaCe0.7Zr0.1Y0.1Yb0.1O3-δ (BCZYYb)||SFN113/327 configuration and single cell tests with Ni-BCZYYb||BCZYYb||SFN113/327 configuration indicate that the SFN113/327 composite electrode with a mass ratio of 1:0.2 displays the best electrocatalytic performance, achieving a power output of 502 mW cm−2 at 700 °C. The work not only in-situ synthesizes the SFN113/327 triple conducting composite electrode, but also introduces a novel method for developing proton conducting electrode materials.

Macroporous polymer-derived ceramics produced by standard and additive manufacturing methods: How the shaping technique can affect their high temperature thermal behavior

This work proposes the processing of porous ceramic lattices via three polymer-derived ceramic routes, namely powder bed fusion and infiltration, fused filament fabrication and replica, and a direct replica of a foamed polymer. A common feature in the processing of these lattices is the use of the same polysilazane as the preceramic source for the Si-C-N-O network that builds up during ceramization.We adopted rotated cube, honeycomb and randomized cellular geometries as a matter of comparison for thermal exchange when an air flow is forced through the structures up to 1050 °C. The three procedural pathways are discussed in their limitations regarding geometry, polymer-to-ceramic conversion, high-temperature heat exchange performance and durability. In this regard, while rotated cube geometry results in the best thermal exchange and highest pressure drop, we show a correlation between chemical composition and high temperature oxidation of the Si-C-N-O network, possibly attributed to the selection of the processing routes.

Performance analysis and PID control strategy optimization of the electronic expansion valve on the single-tube heat exchange experimental platform

In this paper, the fuzzy strategy is used to optimize the electronic expansion valve (EEV) PID control on the single-tube heat exchange experimental platform (STHEEP). The control strategy is implemented through LabVIEW. The EEV serves as the control object, and the superheat degree is the control target parameter. A comparative analysis of the control performance and heat exchange performance with the two different PID control strategies is conducted to optimize the EEV control. According to the results of the experiment, using fuzzy strategy to optimize the PID control shows significant effects, leading to a high improvement in the performance of the experimental platform. Compared with the routine PID control (RPIDC), the overshoot of the fuzzy PID control (FPIDC) is reduced, the regulating time is shorter, and the fluctuation range of the superheat degree is smaller. In the steady state stage, the average heat exchange coefficient of the test section with FPIDC is higher than that with RPIDC. The FPIDC provides higher control precision, and the energy consumption during the experimental regulating process is lower. Therefore, the optimized fuzzy PID control strategy of the EEV can be used as a preferred option in future research on superheat degree control.

Sustainable heating and cooling for residential buildings: coaxial ground heat exchangers

As the world fights climate change challenges and the soaring demand for energy-efficient solutions, the need for sustainable heating and cooling systems in residential buildings has become paramount. Traditional systems rely on fossil fuels and contribute significantly to greenhouse gas emissions. Ground source heat pumps (GSHPs) have emerged as a promising technology, offering a sustainable alternative to conventional space conditioning systems. Central to the success of GSHPs is the efficient and reliable operation of their ground heat exchangers, with lower installation costs, as a prospective solution for future residential applications. This paper presents a numerical axisymmetric (r-z) finite volume method solution of the thermal performance of coaxial ground heat exchangers (CGHE) that incorporate phase change material (PCM) in the ground for GSHP applications. An analysis of the CGHE with PCM grout is presented, highlighting the advantages of heat exchange performance over normal grouts. The temperature comparison on three different points in the grout with different grouting materials was carried out to analyse the behaviour of different grouting materials during the heat exchange process. The investigation from a temperature point of view showed that the inclusion of PCM in the grouting material improves the thermal performance of the CGHE.

Involvement of the Lung Parenchyma Analyzed by Frequency Components of the Tidal Volume Assessed by Electrical Bioimpedance

Pulmonary function tests are vital for detecting pathologies, especially chronic obstructive pulmonary diseases (COPD), emphasizing the importance of assessing lung parenchyma involvement in maintaining proper gas exchange. Electrical impedance tomography (EIT) offers a non-invasive alternative for respiratory function evaluation while preserving natural breathing. We propose using EIT to detect lung parenchyma conditions by analyzing tidal volume patterns (by averaging the impedance image) in the frequency domain. Twenty COPD patients underwent simultaneous evaluation with a pneumotachometer and an EIT device, performing three 30-second respiratory maneuvers. FFT spectra analysis yielded parameters, including the area under the curve and quartiles (25 %, 50 %, 75 %) of power values in six frequency regions. Correlations between these parameters and clinical test results (pulmonary diffusing capacity and arterial blood gas analysis) revealed significant associations, particularly with PCO2. Multiple linear regression analysis predicted PCO2 with an R2adj = 0.827, suggesting the potential for non-invasively detecting lung parenchyma affectation by correlating FFT bioimpedance ventilatory patterns with gas exchange performance in COPD patients.

Experimental Study on Ultra-Low Concentration Methane Regenerative Thermal Oxidation

As a major coal country, China faces the issue of significant gas emissions during the coal mining process. This study aims to improve the utilization efficiency of mine gas, reduce greenhouse gas emissions, and promote the low-carbon and green transformation of the coal industry. A 10 kW gas regenerative thermal oxidizer (RTO) experimental system was constructed. The effects of initial methane concentration, low-temperature flue gas proportion, and operating load on combustion temperature, methane oxidation rate, high-temperature flue gas energy, and system thermal efficiency were studied. The results show that when the combustion temperature is below 600 °C, the CH4 combustion reaction cannot proceed effectively, and the system temperature continuously decreases and cannot be maintained stably. The experiment determines the stable operating methane concentration range of the RTO. In this experimental system, the lower limit of the initial methane concentration is 0.28%, corresponding to an 86% methane oxidation rate. As the initial methane concentration decreases, the combustion temperature also decreases, and the methane oxidation rate follows suit. The higher the low-temperature flue gas proportion, the higher the combustion temperature, and the system’s thermal efficiency and output heat decrease with the increase in the low-temperature flue gas proportion. This experiment explores multiple factors affecting regenerative thermal oxidation, providing a basis for ensuring the safe and stable operation of the system and its optimization. Improving the thermal insulation and heat exchange performance of the storage body can expand the lower limit of the initial methane concentration, thereby increasing the stability and thermal efficiency of the system.