Electron Conductivity Research Articles

Bond-Engineered MoSe2 Nanosheets with Expanded Layers and an Enriched 1T Phase for Highly Efficient Na+ Storage.

MoSe2 has attracted significant interest for Na+ storage due to its large interlayer distance, favorable band gap structure, and satisfying theoretical specific capacity. Nevertheless, the poor conductivity and large volume stress/strain always lead to poor cycle stability and limited rate capability. Herein, the P-Se bond and phase engineering strategies are proposed to enhance the stability of MoSe2 with the assistance of carbon compositing. Systematical characterizations confirm that the presence of a strong P-Se bond can ensure the good structural stability and enlarge the layer distance of the MoSe2 anode. 1T phase-enriched composition endows excellent conductivity and thus fast Na+ transport kinetics. Additionally, the combination of carbon contributes to the improvement of electron conductivity, further enhancing the reversible Na+ storage and cyclic stability. Consequently, an ultrastable reversible specific capacity of 347.8 mAh g-1 with a high retention ratio of 99.1% can be maintained after 1000 cycles at 1 A g-1, which is superior to the previous reports of MoSe2 nanosheets. The presented strategy is ingenious, offering an effective guidance to designing advanced electrodes to be applied in rechargeable batteries with a long lifespan.

Energy Band-Modulated SnO Anodes with Improved Rate Capacity and Initial Coulombic Efficiency for Sodium-Ion Batteries.

An efficient interface and composition modification strategy is proposed to significantly increase the rate capacity and initial Coulombic efficiency (ICE) of SnO anodes via energy band structure modulation for Na-ion batteries (SIBs). The as-fabricated SnO@Bi@C material with Bi nanocrystals homogeneously dispersed on and around the SnO surface is prepared by an electrospinning method. The excellently dispersed Bi nanocrystals realize an effective interface contact with SnO and Na2O, which effectively lowers the electron conduction barriers and promotes sodium-ion release and transport upon the desodiation process, increasing the rate capacity and ICE of the SnO anode. The prepared SnO@Bi@C exhibits a much higher rate capacity up to 10 A g-1, except an improved ICE of 80.67%, compared to 57.38% of SnO@C. Importantly, the intercalation of Na+ between layer-structured Bi galleries provides a good basis for excellent cycle stability due to the highways constructed inside the prepared composites. This finding provides an effective tactic to establish ion transport high-speed channels, which essentially increase the rate performance and the ICE of the SnO-based anodes.

Enhancing the electrochemical properties of biopolymer composites using starch‐graphene nanoplatelets

AbstractThe study presents the ideal distribution of graphene nanoplatelets (GNP) within the thermoplastic starch (TPS) matrix significantly elevated the thermal and electrical conductivities, as well as the electrochemical efficiency of the biocomposites. Additionally, the incorporation of GNP resulted in an increased thermal stability for the TPS, as indicated by the elevated temperatures required for maximum degradation. The biocomposites exhibited a self‐aligned layered structure, creating conductive pathways and enhancing electron conduction. An electrical conductivity increased as the concentration of GNP increased, with the highest conductivity observed on the top and bottom surface with the value of 4.23 × 10−7 S/m and 3.92 × 10−6 S/m when 12 wt% of GNP was added. The presence of hydroxyl groups in TPS facilitated the formation of hydrogen bonds with GNP, preventing GNP from stacking and forming a more uniform conductive network within the film. The addition of 15 wt% GNP also improved the capacitive performance of the TPS matrix, as evidenced by higher current responses and larger quasi‐rectangular areas in the cyclic voltammetry curves compared to neat TPS. The Nyquist plots which are illustrated impedance data showed that the TPS film with 12 wt% GNP exhibits the smallest semicircle, indicating the highest conductivity which is suggested that GNP improves charge transfer compared to pure TPS.Highlights Optimal dispersion of GNP enhanced the biocomposite's properties. The electrical conductivity increases with the GNP content until 12 wt%. TPS/GNP self‐aligned layered improved conduction and capacitive behavior. GNP improved thermal stability by restricting polymer chain movement. Electrochemical impedance shows improved properties of TPS/GNP.

Polycatenanes Formed of Self‐Assembled Metal‐Organic Cages

AbstractPoly‐[n]‐catenanes (PCs) self‐assembled of three‐dimensional (3D) metal organic cages (MOCs) (hereafter referred to as PCs‐MOCs) are a relatively new class of mechanically interlocked molecules (MIMs) that combine the properties of MOCs and polymers. The synthesis of PCs‐MOCs is challenging because of the difficulties associated with interlocking MOCs, the occurrence of multiple weak supramolecular electrostatic interactions between cages, and the importance of solvent templating effects. The high density of mechanical bonds interlocking the MOCs endows the MOCs with mechanical and physical properties such as enhanced stability, responsive dynamic behavior and low solubility, which can unlock new functional properties. In this Minireview, we highlight the benefit of interlocking MOCs in the formation of PCs‐MOCs structures as well as the synthetic approaches exploited in their preparation, from thermodynamic to kinetic methods, both in the solution and solid‐states. Examples of PCs‐MOCs self‐assembled from various types of nanosized cages (i.e., tetrahedral, trigonal prismatic, octahedral and icosahedral) are described in this article, providing an overview of the research carried out in this area. The focus is on the structure–property relationship with examples of functional applications such as electron conductivity, X‐ray attenuation, gas adsorption and molecular sensing. We believe that the structural and functional aspects of the reviewed PCs‐MOCs will attract chemists in this research field with great potential as new functional materials in nanotechnological disciplines such as gas adsorption, sensing and photophysical properties such as X‐ray attenuation or electron conductivity.

Polycatenanes Formed of Self-Assembled Metal-Organic Cages.

Poly-[n]-catenanes (PCs) self-assembled of three-dimensional (3D) metal organic cages (MOCs) (hereafter referred to as PCs-MOCs) are a relatively new class of mechanically interlocked molecules (MIMs) that combine the properties of MOCs and polymers. The synthesis of PCs-MOCs is challenging because of the difficulties associated with interlocking MOCs, the occurrence of multiple weak supramolecular electrostatic interactions between cages, and the importance of solvent templating effects. The high density of mechanical bonds interlocking the MOCs endows the MOCs with mechanical and physical properties such as enhanced stability, responsive dynamic behavior and low solubility, which can unlock new functional properties. In this Minireview, we highlight the benefit of interlocking MOCs in the formation of PCs-MOCs structures as well as the synthetic approaches exploited in their preparation, from thermodynamic to kinetic methods, both in the solution and solid-states. Examples of PCs-MOCs self-assembled from various types of nanosized cages (i.e., tetrahedral, trigonal prismatic, octahedral and icosahedral) are described in this article, providing an overview of the research carried out in this area. The focus is on the structure-property relationship with examples of functional applications such as electron conductivity, X-ray attenuation, gas adsorption and molecular sensing. We believe that the structural and functional aspects of the reviewed PCs-MOCs will attract chemists in this research field with great potential as new functional materials in nanotechnological disciplines such as gas adsorption, sensing and photophysical properties such as X-ray attenuation or electron conductivity.

Ionic Pumping Effect at the Tailored Mesoporous Carbon Interface for an Extra-Stable Lithium Ion Battery at Low Temperatures.

Ion transportation at the interface significantly influences the electrochemical performance of the lithium ion battery, especially at high rates and low temperatures. Here, we develop a controlled self-assembly strategy for constructing a mesoporous carbon nanolayer with a uniform pore size and varied thicknesses on the two-dimensional monolayer MXene substrate. On the basis of the excellent electron conductivity of MXene, the mesoporous carbon layer is found with a voltage-driven ion accumulation effect, acting as an "ionic pump". The thicker mesoporous layer (∼2.28 nm) has the ability to accommodate a substantial quantity of ions, demonstrating enhanced ionic conductivity, remarkable cycling stability (192.8 mAh/g after 9400 cycles at 5.0 A/g), and outstanding rate capability at ambient and sub-zero temperatures (∼601 mAh/g at 0 °C and 0.05 A/g). This work provides valuable insights and guidance for the further development of high-performance electrode materials at high rates or low temperatures.

Construction of an Ohmic Contact Cathode by Two Metal Sulfides for efficient Capture and Catalysis of Polysulfide.

The slow reaction kinetics and severe shuttle effect of lithium polysulfide make Li-S battery electrochemical performance difficult to meet the demands of large electronic devices such as electric vehicles. Based on this, an electrocatalyst constructed by metal phase material (MoS2) and semiconductor phase material (SnS2) with ohmic contact is designed for inhibiting the dissolution of lithium polysulfide with improving the reaction kinetics. According to the density-functional theory calculations, it is found that the heterostructured samples with ohmic contacts can effectively reduce the reaction-free energy of lithium polysulfide to accelerate the sulfur redox reaction, in addition to the excellent electron conduction to reduce the overall activation energy. The metallic sulfide can add more sulfophilic sites to promote the capture of polysulfide. Thanks to the ohmic contact design, the carbon nanotube-MoS2-SnS2 achieved a specific capacity of 1437.2 mAhg-1 at 0.1 C current density and 805.5 mAhg-1 after 500 cycles at 1 C current density and is also tested as a pouch cell, which proves to be valuable for practical applications. This work provides a new idea for designing an advanced and efficient polysulfide catalyst based on ohmic contact.

A DFT study on catalytic cracking mechanism of tar by Ni or Fe doped CaO during biomass steam gasification

The presence of byproduct tar seriously reduces the efficiency and syngas quality in the biomass gasification process. The current understanding of CaO-catalyzed tar cracking mainly depends on experimental findings and conjecture about CaO properties. However, there is a significant lack of simulation studies that explore the conversion mechanism at the molecular level. In this work, the reaction mechanism of tar catalytic cracking on Ni or Fe doped CaO was studied using density functional theory simulation. The benzene, phenol and toluene were chosen as the tar model compounds to determine the influences of Ni and Fe on the adsorption characteristics of CaO surface. CaO doped with Ni and Fe increases its electron affinity and electron conductivity from 4.99 to 9.21/5.58 eV-1. It also enhances the interactions between the d-orbitals of Ni/Fe atoms and the p-orbitals of O atoms. The C-H activation of ·CH3 is the most kinetically and energetically feasible first step. The Ni-doped CaO and Fe-doped CaO decrease the energy barriers by 15.7 % and 21.7 %, respectively, compared with undoped CaO. Ni enhances the surface adsorption capacity for ·H radicals to form OH* at the O top site, whereas Fe promotes the stabilization of ·H radicals at the Ca-O vacancy. Through the enhancement of chemical adsorption capacity, improvement of electronic properties, introduction of electron reorganization and orbital hybridization, low-energy shift of energy levels, and generation of new energy states (from -0.85 to -1.64/-3.05 eV), the surfaces of Ni-doped CaO and Fe-doped CaO provide a favorable electronic environment for the tar catalytic cracking, which improves the reaction efficiency and selectivity.

Highly sensitive electrochemical sensor for glutathione detection using zinc oxide quantum dots anchored on reduced graphene oxide

This work presents a highly sensitive and selective electrochemical sensor for glutathione (GSH) detection using a glassy carbon (GC) electrode modified with zinc oxide quantum dots-reduced graphene oxide nanocomposites (ZnO QDs-rGO NCs). The ZnO QDs (diameters about ∼2 to 8 nm) were synthesized and successfully anchored onto the surface of reduced graphene oxide (rGO). The resulting nanocomposites were then characterized using various spectroscopic and microscopic techniques. The wurtzite crystal structure of ZnO and anchored onto the rGO surface were confirmed by X-ray diffraction (XRD) and transmission electron microscopy (TEM). The synergistic interaction between ZnO QDs with rGO provides a large surface area, high conductivity, and efficient transfer of electrons, resulting in improved electrocatalytic activity for GSH oxidation. The ZnO QDs-rGO/GC electrode exhibits exceptional performance with a wide linear range (0.01–10 μM), high sensitivity (3.66 μAμM−1), and excellent selectivity for GSH. The sensor demonstrates good analytical stability, characterized by high reproducibility (%RSD = 2.90%) and repeatability (%RSD = 1.49%), and maintains its performance in the presence of common biological interferences. The applicability of the sensor was validated through successful GSH detection in complex matrices like human blood and pharmaceutical capsules, achieving recovery rates of 98.1-102.0% with excellent reliability.

Hexagonal MoO3 Anode with Extremely High Capacity and Cyclability for Lithium-Ion Battery: A Combined Theoretical and Experimental Study.

It is essential and still remains a big challenge to obtain fast-charge anodes with large capacities and long lifespans for Li-ion batteries (LIBs). Among all of the alternative materials, molybdenum trioxide shows the advantages of large theoretical specific capacity, distinct tunnel framework, and low cost. However, there are also some key shortcomings, such as fast capacity decaying due to structural instability during Li insertion and poor rate performance due to low intrinsic electron conductivity and ion diffusion capability, dying to be overcome. A unique strategy is proposed to prepare Ti-h-MoO3-x@TiO2 nanosheets by a one-step hydrothermal approach with NiTi alloy as a control reagent. The density functional theory (DFT) calculations indicate that the doping of Ti element can make the hexagonal h-MoO3-x material show the best electronic structure and it is favor to be synthesized. Furthermore, the hexagonal Ti-h-MoO3-x material has better lithium storage capacity and lithium diffusion capacity than the orthogonal α-MoO3 material, and its theoretical capacity is more than 50% higher than that of the orthogonal α-MoO3 material. Additionally, it is found that Ti-h-MoO3-x@TiO2 as an anode displays extremely high reversible discharge/charge capacities of 1326.8/1321.3 mAh g-1 at 1 A g-1 for 800 cycles and 611.2/606.6 mAh g-1 at 5 A g-1 for 2000 cycles. Thus, Ti-h-MoO3-x@TiO2 can be considered a high-power-density and high-energy-density anode material with excellent stability for LIBs.

Synergistic effect of carbon nanotube and encapsulated carbon layer enabling high-performance SnS2-based anode for lithium storage

Tin disulfide (SnS2), due to large interlayer spacing and high theoretical capacity, is regarded as a prospective anode material for lithium-ion batteries. Nevertheless, the poor electron conductivity of SnS2 and huge volumetric change during the lithiation/delithiation process lead to a rapid capacity decay of the battery, hindering its commercialization. To address these issues, herein, SnS2 is in-situ grown on the surface of carbon nanotubes (CNT) and then encapsulated with a layer of porous amorphous carbon (CNT/SnS2@C) by simple solvothermal and further carbonization treatment. The synergistic effect of CNT and porous carbon layer not only enhances the electrical conductivity of SnS2 but also limits the huge volumetric change to avoid the pulverization and detachment of SnS2. Density functional theory calculations show that CNT/SnS2@C has high Li+ adsorption and lithium storage capacity achieving high reaction kinetics. Consequently, cells with the CNT/SnS2@C anode exhibit a high lithium storage capacity of 837 mAh/g after 100 cycles at 0.1 A/g and retaining a capacity of 529.8 mAh/g under 1.0 A/g after 1000 cycles. This study provides a fundamental understanding of the electrochemical processes and beneficial guidance to design high-performance SnS2-based anodes for LIBs.

Lithium-Ion battery silicon Anodes: Surface engineering with novel additives for enhanced ion and electron transport

Silicon (Si) stands as a promising candidate for high-capacity anode materials in the next-generation lithium-ion batteries (LIBs) due to extremely high specific capacity. However, silicon application is hindered by its inherently poor electron and ion conductivities, as well as structural instability during the repeated charging/discharging. To address these challenges, a novel functional surface modification agent, diethylenetriaminepenta(methylenephosphonic) acid (DTPMP), was decorated on the surface of silicon particles for the first time. The experimental results demonstrate that the DTPMP effectively enhances the cohesion between nano Si particles. This study combines experimental observations with theoretical calculations to analyze the nucleophilic and electrophilic sites of DTPMP and carboxymethyl cellulose (CMC), elucidating the existence state of DTPMP on the nano Si surface. Furthermore, by examining the highest occupied molecular orbital (HOMO) and the lowest unoccupied molecular orbital (LUMO), along with the electrostatic potential (ESP) of DTPMP and solvent molecules in conjunction with Li+, the impact of the phosphate group on the diffusion of Li+ and electrons at the nano Si surface was studied. The electron density difference (EDD) maps for DTPMP and CMC reveal that DTPMP exhibits a more pronounced response in the presence of an electric field, suggesting its enhanced role in facilitating Li+ diffusion. This research offers a novel perspective on enhancing the electrochemical performance of nano Si surfaces, paving the way for the development of advanced LIBs with improved energy storage capabilities.

Topotactic Syntopogenous Sodium Vanadium Fluoride for High-Performance Sodium-Ion Batteries: Electron and Sodium-Ion Reservoirs in Perovskite/Diperovskite Superlattice.

In order to simultaneously accelerate ion and electron transfer in sodium-ion battery (SIB) cathodes, a topotactic superlattice was utilized, in which the atomically intrinsic lattice-matching effect from inner to external surface can boost the charge transfer due to the disappearance of the heterojunction interface. Herein, a topotactic syntopogenous Na3VF6/NaVF3 superlattice formulated as Na2.9V1.1F6 (NVF) was synthesized by a facile one-step low-temperature hydrothermal reaction. NVF nanoparticles show an excellent Na+ storage capacity (∼205 mAh g-1) in a high voltage window up to 4.2 V with ultralong cycling stability. That is associated with the mixed occupancy of V and Na in NVF. The multivalent V centers serve as electron reservoirs to inhibit phase transformation, and the Na-enriched Na3VF6 with better electron conductivity acts as a Na+ reservoir for effective electron transfer. Highly reversible (de)intercalation of Na+ is achieved in the channel of perovskite-type NaVF3 with structural integrity.

Synthesis, characterization, in vitro and in silico assessment of novel diclofenac derivative metal complexes

A novel hydrazone ligand was synthesized by condensing diclofenac hydrazide with salicylaldehyde. This ligand was then used to create complexes with cobalt(II), nickel(II), copper(II), gadolinium(III), lanthanum(III), and silver(I). Structural characterization of these compounds was achieved through various techniques, including nuclear magnetic resonance spectroscopy, infrared spectroscopy, ultraviolet-visible spectroscopy, mass spectrometry, elemental analysis, thermal analysis, magnetic susceptibility measurements, electron spin resonance spectroscopy, X-ray diffraction, and conductivity measurements. The inhibitory effects of the synthesized compounds on cyclooxygenase-1 (COX-1) and cyclooxygenase-2 (COX-2) enzymes, critical targets for anti-inflammatory drugs, were assessed. Notably, the cobalt(II) and silver(I) complexes exhibited high selectivity for inhibiting COX-2, with selectivity indices of 118.75 and 105.00, respectively. The antitumor potential of the compounds was evaluated against MCF-7 (breast cancer) and HepG-2 (liver cancer) cell lines. The copper(II) and gadolinium(III) complexes demonstrated the highest efficacy, significantly inhibiting the growth of both cancer cell lines with half-maximal inhibitory concentration (IC50) values as low as 0.37 µM and 0.58 µM (MCF-7) and 0.35 µM and 0.67 µM (HepG-2), respectively. These complexes outperformed the original ligand in inhibiting cancer cell growth. In silico studies, using the SwissADME web tool and AutoDocke Vina, corroborated the experimental findings and provided insights into the compounds' physicochemical properties, pharmacokinetics, drug-likeness, and potential binding interactions with COX-1, COX-2, and the target proteins in the cancer cell lines.

Pt atomic clusters/MoS2 nanosheets/Co-doped hollow carbon nanofibers for high-current–density alkaline hydrogen production

The application of layered molybdenum disulfide (MoS2) in catalytic hydrogen production has attracted great interest, while their catalytic properties are limited by poor electron conductivity and a few catalytically active sites. In this work, we demonstrated a highly active electrocatalyst for large-scale hydrogen production, consisting of two-dimensional (2D) Pt-MoS2 nanosheets along one-dimensional (1D) cobalt nanoparticle integrated carbon hollow nanofibers (Co@CHNF). The as-prepared Pt-MoS2-Co@CHNF had a large specific surface area (44.5 m2 g−1). X-ray photoelectron spectrometer (XPS) and spherical aberration corrected transmission electron microscope (AC-STEM) demonstrated that Pt atomic clusters (Pt ACs) were doped on MoS2 nanosheets by thermodynamically induced spontaneous interfacial redox between MoS2 and H₂PtCl₆. The Pt-MoS2-Co@CHNF based catalysts exhibited an overpotential as low as 91 mV for 10 mA cm−2 and 258 mV for 200 mA cm−2 in 1 M KOH electrolyte, and there is no significant floating for catalytic active with 14 h continuous operation, which demonstrates its excellent long-term operation durability, significantly superior to the previously reported state-of-the-art Co-based or Mo-based catalysts. In particular, the self-supporting binder-free Pt-MoS2-Co@CHNF catalyst-based electrode showed an ultra-high current density of 500 mA cm−2 at a low overpotential of 301 mV, without any decrease after 24 h operation at 500 mA cm−2 in 1 M KOH seawater electrolyte, representing a great potential for large-scale seawater hydrogen production.

Mitigating chain degradation of lithium-rich manganese-based cathode material by surface engineering

Due to offering joint cationic and anionic redox, lithium-rich manganese-based layered oxides (LMLOs) allow high energy density in lithium-ion batteries. However, the oxygen loss, electrode-electrolyte interface side reactions and the structural degradation have resulted in continuous performance decay, hindering the scale-up application of LMLOs. Here, Li1.3V0.94(BO3)2 (LVB) is uniformly coated on the Li1.2Mn0.54Co0.13Ni0.13O2 (LMNCO) surface by using a sol-gel method combined with a high-temperature calcination. By applying multiple characterizations including in-situ XRD, DEMS, HRTEM, AFM and electrochemical test, we prove that the LVB layer provides a physical barrier, which effectively inhibits the surface reactivity and blocks the chain degradation from the source, improves the reversibility of O2- redox and prevents the phase transition and structural degradation propagating from the surface to the bulk. Moreover, the kinetic investigations and calculations reveal that the LVB modification not only improves the electron conductivity of materials by decreasing the surface work function and increasing the electron density near the Fermi energy level, but also provides expanded pathways with lower impedance to facilitate the Li+ transfer and diffusion. Impressively, the modified cathode exhibits the higher rate performance (151 mAh g-1 at 5C) and improved cycle stability under high cutoff voltage (217.7 mAh g-1 after 200 cycles at 0.2C in 2.0–4.8 V, 92.5 % capacity retention; even in 2.0–5 V, 93.9 % after 100 cycles). This work systematically investigates the inhibiting degradation mechanism and establishes the correlation between the intrinsic structure and surface engineering, and offers valuable insight into the development of high-performance LMLOs.

Enhanced performance of graphene-incorporated electrodes for solid-state lithium-sulfur batteries through facilitated ionic diffusion pathways

Significant progress has been achieved in advancing all-solid-state lithium-sulfur batteries through the development of sulfide solid electrolytes. Nonetheless, a challenge lies in creating a percolated ion–electron conduction path with intimate contact between charge carriers throughout the cathode which is crucial for enhancing overall efficiency and addressing issues related to slow kinetics and impedance during battery operation. This study introduces a framework elucidating how the integration of graphene enhances electrode performance by refining ionic diffusion pathways. An idealized ionic diffusion pathway characterized by a continuous ionic network, facilitating minimum diffusion distances, is proposed. Through a parametric study substituting portions of ionic and electronic conductive agents with graphene, the impact on total ionic and electronic conductivity of positive electrodes was comprehended. The findings underscore the critical role of optimum graphene content, which fills the gaps between ionic conductive materials and creates the shortest diffusion paths for ions and electrons. While incorporating graphene into cathode electrodes is not novel, it is noteworthy that graphene, as a mixed ion–electron conductive material, significantly enhances ion mobility due to its 2D structure, addressing a crucial aspect of cathode performance. Upon achieving optimum composite formulation, empirical findings demonstrate substantial performance improvement, including a 17.7% increase in initial capacity and a remarkable 21% enhancement in capacity retention compared to electrodes without graphene.

High Performance Aqueous Zinc-Ion Batteries Developed by PANI Intercalation Strategy and Separator Engineering.

Aqueous zinc-ion batteries (ZIBs) have attracted burgeoning attention and emerged as prospective alternatives for scalable energy storage applications due to their unique merits such as high volumetric capacity, low cost, environmentally friendly, and reliable safety. Nevertheless, current ZIBs still suffer from some thorny issues, including low intrinsic electron conductivity, poor reversibility, zinc anode dendrites, and side reactions. Herein, conductive polyaniline (PANI) is intercalated as a pillar into the hydrated V2O5 (PAVO) to stabilize the structure of the cathode material. Meanwhile, graphene oxide (GO) was modified onto the glass fiber (GF) membrane through simple electrospinning and laser reduction methods to inhibit dendrite growth. As a result, the prepared cells present excellent electrochemical performance with enhanced specific capacity (362 mAh g-1 at 0.1 A g-1), significant rate capability (280 mAh g-1 at 10 A g-1), and admirable cycling stability (74% capacity retention after 4800 cycles at 5 A g-1). These findings provide key insights into the development of high-performance zinc-ion batteries.

Cow manure biochar for activation of peroxymonosulfate to degrade 17β-estradiol: Performance and mechanism

Estrogens are widely detected in the environment and can strongly disrupt the endocrine systems of humans in extremely minute concentrations. Therefore, it is imperative to address possible 17β-estradiol (17β-E2) pollution and explore resourceful utilization methods from cow manure, which contains estrogen. In this study, cow manure biochar (CBC) was successfully prepared and used for the activation of peroxymonosulfate (PMS), attaining a 17β-E2 degradation rate exceeding 90 % within a mere 10 min. Optimal degradation performance was achieved at 2 mg/L 17β-E2 concentration, 2 mM PMS concentration, and 0.2 g/L CBC concentration. Furthermore, the influence of biochar-activated PMS on estrogen degradation was thoroughly explored under various environmental factors. The key reactive oxygen species were identified as O2– and 1O2 by conducting quenching experiments and delayed experiments. This study elucidated the occurrence of direct electron conduction and the generation of reactive oxygen species to degrade 17β-E2. Furthermore, the phenol group on the benzene ring and the hydroxyl group on the cyclopentane in 17β-E2 as the susceptible reaction sites during the degradation process were predicted using density functional theory (DFT). This study presents promising opportunities for the resourceful utilization of cattle manure and the mitigation of environmental pollution by endocrine disruptors.

DFT simulations of photovoltaic parameters of dye‐sensitized solar cells with new efficient sensitizer of indolo[3, 2‐b]carbazole complexes

AbstractDeveloping economical and high‐performing sensitizers is crucial in advancing dye‐sensitized solar cells (DSSCs) and optoelectronics. This research paper explores the potential of novel red light‐absorbing organic dyes based on Indolo[3,2‐b]carbazole (ICZ) as the donor applied in co‐sensitizer‐free DSSCs for breakthroughs in photovoltaic (PV) applications. DFT and TD‐DFT based computational methods were employed to calculate the conduction band levels, electron injection capabilities, and power conversion efficiency (PCE) of metal‐free organic dyes (ICZ1–ICZ9) having D‐A‐π‐A architecture. Comprehensive analyses included NBO, DOS, FMO, ICT, MEP, binding energy, and TDM analysis. Quantum chemical calculations of the structural, photochemical, and electrochemical properties, as well as the key parameters, reveals that all the designed dyes could be an excellent candidate for high‐efficiency DSSCs due the small energy gap (2.130–1.947 eV), longer wavelength absorption (759.47–520.63 nm), longer lifetimes (15.65–6.67 ns), a lower ΔGreg (0.29–0.14 eV), a significant dipole moment changes (31.489–16.195D), LHE (0.95‐0.46), the large qCT (0.962–0.689), small DCT (7.657, 4.897 Å), and VOC (1.13–0.86 eV). This quantum simulation showed that, when compared to reference D8, the photovoltaic dyes ICZ8, ICZ2, and ICZ7 are recognized as being eye‐catching. Furthermore, dye@(TiO2)9 cluster model results demonstrate promising prospects for enhancing the photovoltaic (PV) performance of ICZ1–ICZ9 dyes by electron injection and conduction band (CB) engineering. This study will help the experimentalists for developing ICZ‐based PVs as more efficient and sustainable energy solutions.