Electrochemical Compatibility Research Articles

Expanding the Phase Space for Halide-Based Solid Electrolytes: Li-Mg-Zr-Cl Spinels.

Chloride-based solid electrolytes are intriguing materials owing to their high Li+ ionic conductivity and electrochemical compatibility with high-voltage oxide cathodes for all-solid-state lithium batteries. However, the leading examples of these materials are limited to trivalent metals (e.g., Sc, Y, and In), which are expensive and scarce. Here, we expand this materials family by replacing the trivalent metals with a mix of di- and tetra-valent metals (e.g., Mg2+ and Zr4+). We synthesize Li2Mg1/3Zr1/3Cl4 in the spinel crystal structure and compare its properties with the high-performing Li2Sc2/3Cl4 that has been reported previously. We find that Li2Mg1/3Zr1/3Cl4 has lower ionic conductivity (0.028 mS/cm at 30 °C) than the isostructural Li2Sc2/3Cl4 (1.6 mS/cm at 30 °C). We attribute this difference to a disordered arrangement of Mg2+ and Zr4+ in Li2Mg1/3Zr1/3Cl4, which may block Li+ migration pathways. However, we show that aliovalent substitution across the Li2-z Mg1-3z/2Zr z Cl4 series between Li2MgCl4 and Li2ZrCl6 can boost ionic conductivity with increasing Zr4+ content, presumably due to the introduction of Li+ vacancies. This work opens a new dimension for halide-based solid electrolytes, accelerating the development of low-cost solid-state batteries.

Electrospun Nano-Porous Cellulose Acetate Membrane Casted with Chitosan for Solid-State Sodium-Ion Batteries

Emerging as a safe and economically viable alternative to lithium-ion batteries, the solid-state sodium ion battery (ss-SIB) has captured increasing attention as a transformative technology for realizing a decarbonized economy and ensuring a sustainable energy supply. Here we report a nanoarchitecture strategy of biodegradable, biocompatible, and naturally abundant cellulose derivative (cellulose acetate, CA) and chitosan (CH) biopolymer-based nano-porous electrospun composite electrolyte (ECE) for flexible and wearable ss-SIBs. A simple combination of electrospinning and solution casting was utilized to fabricate mechanically robust (13.76 MPa), thin-film (0.067 mm), highly flexible, and high room temperature Na-ion conductive (1.04 x 10-4 S.cm-2) ECE. Lower activation energy (Ea = 0.13 eV) indicates easy charge carrier diffusion ability of as prepared ECE. The electrochemical stability window (ESW = 3.45 V) of ECE is studied by the linear sweep voltammetry (LSV) with respect to stainless steel and sodium metal electrodes. Uniform galvanostatic Na plating and stripping at room temperature is observed over 900 hrs at 0.5 mA•cm-2 current density in symmetric (Na|ECE|Na) cell performance, this underscores impressive electrochemical stability and compatibility with sodium metal. Using Na3V2(PO4)3 (NVP) as cathode, ECE, and Na metal as anode in the full cell, specific discharge capacity of 83 mA×h×g-1 at room temperature was attained at 0.1 C rate, highlighting the practical applicability of the nanostructured electrospun composite electrolyte for flexible and wearable ss-SIBs. Keywords Cellulose acetate, chitosan, electrospun, solid-state sodium-ion battery, specific discharge capacity.

Enhancing Reversibility and Stability of Mg Metal Anodes: High-Exposure (002) Facets and Nanosheet Arrays for Superior Mg Plating/Stripping.

Magnesium metal batteries (MMBs), recognized as promising contenders for post-lithium battery technologies, face challenges such as uneven magnesium (Mg) plating and stripping behaviors, leading to uncontrollable dendrite growth and irreversible structural damage. Herein, we have developed a Mg foil featuring prominently exposed (002) facets and an architecture of nanosheet arrays (termed (002)-Mg), created through a one-step acid etching method. Specifically, the prominent exposure of Mg (002) facets, known for their inherently low surface and adsorption energies with Mg atoms, not only facilitates smooth nucleation and dense deposition but also significantly mitigates side reactions on the Mg anode. Moreover, the nanosheet arrays on the surface evenly distribute the electric field and Mg ion flux, enhancing Mg ion transfer kinetics. As a result, the fabricated (002)-Mg electrodes exhibit unprecedented long-cycle performance, lasting over 6000 h (>8 months) at a current density of 3 mA cm-2 for a capacity of 3 mAh cm-2. Furthermore, the corresponding pouch cells equipped with various electrolytes and cathodes demonstrate remarkable capacity and cycling stability, highlighting the superior electrochemical compatibility of the (002)-Mg electrode. This study provides new insights into the advancement of durable MMBs by modifying the crystal structure and morphology of Mg.

Enhancing Reversibility and Stability of Mg Metal Anodes: High‐Exposure (002) Facets and Nanosheet Arrays for Superior Mg Plating/Stripping

AbstractMagnesium metal batteries (MMBs), recognized as promising contenders for post‐lithium battery technologies, face challenges such as uneven magnesium (Mg) plating and stripping behaviors, leading to uncontrollable dendrite growth and irreversible structural damage. Herein, we have developed a Mg foil featuring prominently exposed (002) facets and an architecture of nanosheet arrays (termed (002)‐Mg), created through a one‐step acid etching method. Specifically, the prominent exposure of Mg (002) facets, known for their inherently low surface and adsorption energies with Mg atoms, not only facilitates smooth nucleation and dense deposition but also significantly mitigates side reactions on the Mg anode. Moreover, the nanosheet arrays on the surface evenly distribute the electric field and Mg ion flux, enhancing Mg ion transfer kinetics. As a result, the fabricated (002)‐Mg electrodes exhibit unprecedented long‐cycle performance, lasting over 6000 h (>8 months) at a current density of 3 mA cm−2 for a capacity of 3 mAh cm−2. Furthermore, the corresponding pouch cells equipped with various electrolytes and cathodes demonstrate remarkable capacity and cycling stability, highlighting the superior electrochemical compatibility of the (002)‐Mg electrode. This study provides new insights into the advancement of durable MMBs by modifying the crystal structure and morphology of Mg.

Nature-Inspired Strategy: Novel Borohydride-Based Solid Electrolytes Extracted from Cathode-Electrolyte Interphase.

As the core component of all-solid-state batteries, current solid-state electrolytes fail to simultaneously meet multiple demands, such as their own high performance, the chemical, electrochemical and mechanical compatibility of electrode interface. A fresh perspective is rather desired to guide the development of novel solid electrolytes with comprehensive performance. Herein, this work proposes a novel strategy to synthesize solid electrolytes extracted from cathode-electrolyte interphase (CEI), which is inspired by peach trees secreting peach gum to prevent further damage. A proof-of-concept, using LiBH4-Se and LiBH4-S as prototypes, confirms that as-synthesized electrolytes inherited and improved up the advantages of LiBH4 with unexpected compatibility toward multiple cathodes. It is believed that the family of new electrolytes will be continuously expanded under the guidance of this CEI-derived concept.

P2-Type Na0.84Li0.1Ni0.27Mn0.63O2-Layered Oxide Na-Ion Battery Cathode: Structural Insights and Electrochemical Compatibility with Room-Temperature Ionic Liquids.

Modern technologies that can replace state-of-the-art Li-ion batteries (LIBs), such as Na-ion batteries (NIBs), are currently driving new advancements in energy storage research. Developing functional active materials having sustainable features and enhanced performances able to assess their exploitation in the large-scale market represents a major challenge. Rationally designed P2-type layered transition metal (TM) oxides can enable high-energy NIB cathodes, where the tailored composition directly tunes the electrochemical and structural properties. Such positive electrodes need stable electrolytes, and exploration of unconventional room-temperature ionic liquid (RTIL)-based formulations paves the route toward safer options to flammable organic solvents. Notwithstanding the fact that Li+ doping in these materials has been proposed as a viable strategy to improve structural issues, an in-depth understanding of structure-property relationship as well as electrochemical testing with innovative RTIL-based electrolytes is still missing. Herein, we propose the solid-state synthesis of P2-Na0.84Li0.1Ni0.27Mn0.63O2 (NLNMO) cathode material, which exhibits promising structural reversibility and superior capacity retention upon cycling when tested in combination with RTIL-based electrolytes (EMI-, PYR14-, and N1114-FSI) compared to the standard NaClO4/PC. As unveiled from DFT calculations, lattice integrity is ensured by the reduced Jahn-Teller distortion upon Na removal exerted by Mn4+ and Li+ sublattices, while the good redox reversibility is mainly associated with the electrochemically active Ni2+/Ni3+/Ni4+ series burdening the charge compensation upon desodiation. By declaring the electrochemical compatibility of the P2-NLNMO cathode with three RTIL-based electrolytes and dissecting the role of Li/Ni/Mn sublattices in determining the electrochemical behavior, our comprehensive study enlightens the potential application of this electrode/electrolyte setup for future high-energy NIB prototype cells.

Regulating the Solvation Structure in Polymer Electrolytes for High‐Voltage Lithium Metal Batteries

AbstractSolid polymer electrolytes are promising electrolytes for safe and high‐energy‐density lithium metal batteries. However, traditional ether‐based polymer electrolytes are limited by their low lithium‐ion conductivity and narrow electrochemical window because of the well‐defined and intimated Li+‐oxygen binding topologies in the solvation structure. Herein, we proposed a new strategy to reduce the Li+‐polymer interaction and strengthen the anion‐polymer interaction by combining strong Li+‐O (ether) interactions, weak Li+‐O (ester) interactions with steric hindrance in polymer electrolytes. In this way, a polymer electrolyte with a high lithium ion transference number (0.80) and anion‐rich solvation structure is obtained. This polymer electrolyte possesses a wide electrochemical window (5.5 V versus Li/Li+) and compatibility with both Li metal anode and high‐voltage NCM cathode. Li||LiNi0.5Co0.2Mn0.3O2 full cells with middle‐high active material areal loading (~7.5 mg cm−2) can stably cycle at 4.5 V. This work provides new insight into the design of polymer electrolytes for high‐energy‐density lithium metal batteries through the regulation of ion‐dipole interactions.

Regulating the Solvation Structure in Polymer Electrolytes for High-Voltage Lithium Metal Batteries.

Solid polymer electrolytes are promising electrolytes for safe and high-energy-density lithium metal batteries. However, traditional ether-based polymer electrolytes are limited by their low lithium-ion conductivity and narrow electrochemical window because of the well-defined and intimated Li+-oxygen binding topologies in the solvation structure. Herein, we proposed a new strategy to reduce the Li+-polymer interaction and strengthen the anion-polymer interaction by combining strong Li+-O (ether) interactions, weak Li+-O (ester) interactions with steric hindrance in polymer electrolytes. In this way, a polymer electrolyte with a high lithium ion transference number (0.80) and anion-rich solvation structure is obtained. This polymer electrolyte possesses a wide electrochemical window (5.5 V versus Li/Li+) and compatibility with both Li metal anode and high-voltage NCM cathode. Li||LiNi0.5Co0.2Mn0.3O2 full cells with middle-high active material areal loading (~7.5 mg cm-2) can stably cycle at 4.5 V. This work provides new insight into the design of polymer electrolytes for high-energy-density lithium metal batteries through the regulation of ion-dipole interactions.

Flame-retardant separator coated with Boehmite ammonium polyphosphate composite for high-safety lithium-ion batteries

To enhance the thermal stability, electrochemical compatibility, and overshoot protection of separators, it is common practice to incorporate inorganic particles for separator modification. In this work, we discussed a polypropylene (PP) separator that was coated with a combination of hydrothermal boehmite (AlOOH) and ammonium polyphosphate (APP). The coating layer can greatly reduce the thermal shrinkage rate of the separator, enabling the modified separator to retain its original size at 180 °C. In addition, part of the material formed by the decomposition of the coating material at high temperatures can be well-diluted oxygen, thus reducing the risk of combustion. Furthermore, the presence of the coating layer increases the ionic conductivity and electrolyte wettability, thereby improving the cycle stability of the battery. This study utilizes inexpensive, lightweight, and eco-friendly materials to enhance a commercially available polypropylene separator. This modification not only increases the efficiency of material usage but also enhances the economic and environmental advantages of the improved separator.

Structure and properties of surface layer of TiNi alloy subjected to ion-plasma- and ultrasonic treatment

The paper presents the results of research on morphology, elemental composition, microhardness, corrosion properties of the surface layer of TiNi alloy subjected to ion-plasma (vacuum-arc method) deposition of TiN coating and ultrasonic treatment (UT) with different number of passes (n). The SEM method showed that ultrasonic treatment provides a significant reduction in the amount of the droplet phase on the TiN coating surface. The surface discontinuity of TiN coating at local points was observed with an increase in the number of passes during ultrasonic treatment. The effect of combined processing methods on the microhardness of TiNi sample was studied. It was shown that the synergistic effect can be observed for two hardening methods. The combined strengthening method increased the microhardness of TiNi alloy (1.6 GPa in the as-received state): due to the deposition of a TiN coating – up to 10.9 GPa, due to subsequently ultrasonic treatment – up to 14.5–18.4 GPa depending on the number of passes. For UT + TiN scheme, it was shown that the open circuit potential Ecorr was about –250 mV which is practically independent of the number of passes and determined by the potential value of TiN coating. For TiN + UT scheme, it was found that with an increase in the number of passes, the value of Ecorr shifts towards more negative values approaching the open circuit potential value of the TiNi sample in the as-received state (–350 mV). The analysis of Scanning Vibrating Electrode Technique (SVET) results showed high electrochemical compatibility of substrate (TiNi) and coating (TiN) materials in a chloride environment with minimal current density fluctuations for the samples subjected to UT + TiN and TiN + UT (n = 1). The proposed method for TiNi alloy treatment according to TiN + UT scheme (n = 1) promotes an improvement of surface morphology and corrosion resistance.

Composite scaffold of electrospun nano-porous cellulose acetate membrane casted with chitosan for flexible solid-state sodium-ion batteries

Emerging as a safe and economically viable alternative to lithium-ion batteries, the solid-state sodium ion battery (ss-SIB) has captured increasing attention as a transformative technology for realizing a decarbonized economy and ensuring a sustainable energy supply. Here we report a nanoarchitecture strategy of biodegradable, biocompatible, and naturally abundant cellulose derivative (cellulose acetate, CA) and chitosan (CH) biopolymer-based nano-porous electrospun composite electrolyte (ECE) for flexible and wearable ss-SIBs. A simple combination of electrospinning and solution casting was utilized to fabricate mechanically robust (13.76 MPa), thin-film (0.067 mm), and highly flexible ECE. The ionic conductivity of ECE was enhanced through optimization, taking into account the amount of sodium salt (NaPF6). The resulting ECE exhibited a sodium-ion conductivity of 1.04 ×10−4 S·cm−1 and a sodium ion transference number of 0.48 at room temperature (RT=23 °C). The obtained Na+ transference number of 0.48 and a low activation energy (Ea = 0.13 eV) indicate the easy charge carrier diffusion ability of as-prepared ECE. The electrochemical stability window (ESW = 4.04 V) of ECE is studied by the linear sweep voltammetry (LSV) with the assembly of stainless steel and sodium metal electrodes. Without any interfacial modification, a uniform, stable, and long-time room temperature (RT) galvanostatic Na plating-stripping was observed for 1000 hrs at 0.5 mA·cm−2 current density in a symmetric (Na|ECE|Na) cell, this underscores impressive electrochemical stability and compatibility of ECE with sodium metal. Utilizing Na3V2(PO4)3 (NVP) as cathode, fabricated ECE, and Na metal as anode in a hybrid full cell, a notable RT specific discharge capacity of 98.1 mA·h·g−1 was attained at a rate of 0.1 C with a capacity retention of 93.4 % over 120 charge-discharge cycles. This highlights the practical applicability of the nanostructured electrospun composite electrolyte for flexible and wearable ss-SIBs.

Electrochemical Compatibility of Microzonal Carbon in Ion Uptake and Molecular Insights into Interphase Evolution for Next‐Generation Li‐Ion Batteries

Electrochemical Compatibility of Microzonal Carbon in Ion Uptake and Molecular Insights into Interphase Evolution for Next‐Generation Li‐Ion Batteries

Integration of biocompatible hydrogen evolution catalyst developed from metal-mix solutions with microbial electrosynthesis

Microbial conversion of CO2 to multi-carbon compounds such as acetate and butyrate is a promising valorisation technique. For those reactions, the electrochemical supply of hydrogen to the biocatalyst is a viable approach. Earlier we have shown that trace metals from microbial growth media spontaneously form in situ electro-catalysts for hydrogen evolution. Here, we show biocompatibility with the successful integration of such metal mix-based HER catalyst for immediate start-up of microbial acetogenesis (CO2 to acetate). Also, n-butyrate formation started fast (after twenty days). Hydrogen was always produced in excess, although productivity decreased over the 36 to 50 days, possibly due to metal leaching from the cathode. The HER catalyst boosted microbial productivity in a two-step microbial community bioprocess: acetogenesis by a BRH-c20a strain and acetate elongation to n-butyrate by Clostridium sensu stricto 12 (related) species. These findings provide new routes to integrate electro-catalysts and micro-organisms showing respectively bio and electrochemical compatibility.

A High‐Voltage Solid State Electrolyte Based on Spinel‐Like Chloride Made of Low‐Cost and Abundant Resources

AbstractRecently, halide solid state electrolytes (SSEs) have received great attention owing to their fast ionic conductivity, high oxidation potential, and good chemical and electrochemical compatibility with high voltage cathode materials. However, most of reported halide SSEs contain rather rare and expensive elements, which hinders their sustainable utilizations in practical batteries. Here in this work, under the guidance of systematic modelling based on the density functional theory (DFT), a low‐cost alternative is developed through optimizing the lattice chemistry in a recently identified spinel‐like chloride Li2CrCl4 into Li5/3Cr1/3Zr1/3Cl4 for remarkably enhanced ionic conductivity and stable electrochemical window with respect to the Li‐anode. This new phase has then been synthesized successfully, delivering an ionic conductivity over 1200 times of that of the pristine phase Li2CrCl4, in addition to a high oxidation potential (up to 4.1 V vs Li/Li+) to enable outstanding interfacial compatibility with high voltage cathodes. Such a high‐voltage and fast Li‐ion conducting solid‐state electrolyte is expected to provide a highly desirable basis toward developing high energy‐density all solid‐state batteries (ASSBs) using economical and Earth‐rich elements.

LiNO3‐Based Electrolytes via Electron‐Donation Modulation for Sustainable Nonaqueous Lithium Rechargeable Batteries

AbstractLiPF6 as a dominant lithium salt of electrolyte is widely used in commercial rechargeable lithium‐ion batteries due to its well‐balanced properties, including high solubility in organic solvents, good electrochemical stability, and high ionic conductivity. However, it suffers from several undesirable properties, such as high moisture sensitivity, thermal instability, and high cost. To address these issues, herein, we propose an electron‐donation modulation (EDM) rule for the development of low‐cost, sustainable, and electrochemically compatible LiNO3‐based electrolytes. We employ high donor‐number solvents (HDNSs) with strong electron‐donation ability to dissolve LiNO3, while low donor‐number solvents (LDNSs) with weak electron‐donation ability are used to regulate the solvation structure to stabilize the electrolytes. As an example, we design the LiNO3‐DMSO@PC electrolyte, where DMSO acts as an HDNS and PC serves as an LDNS. This electrolyte exhibits excellent electrochemical compatibility with graphite anodes, as well as the LiFePO4 and LiCoO2 cathodes, leading to stable cycling over 200 cycles. Through spectroscopy analyses and theoretical calculation, we uncover the underlying mechanism responsible for the stabilization of these electrolytes. Our findings provide valuable insights into the preparation of LiNO3‐based electrolytes using the EDM rule, opening new avenues for the development of advanced electrolytes with versatile functions for sustainable rechargeable batteries.

LiNO3 -Based Electrolytes via Electron-Donation Modulation for Sustainable Nonaqueous Lithium Rechargeable Batteries.

LiPF6 as a dominant lithium salt of electrolyte is widely used in commercial rechargeable lithium-ion batteries due to its well-balanced properties, including high solubility in organic solvents, good electrochemical stability, and high ionic conductivity. However, it suffers from several undesirable properties, such as high moisture sensitivity, thermal instability, and high cost. To address these issues, herein, we propose an electron-donation modulation (EDM) rule for the development of low-cost, sustainable, and electrochemically compatible LiNO3 -based electrolytes. We employ high donor-number solvents (HDNSs) with strong electron-donation ability to dissolve LiNO3 , while low donor-number solvents (LDNSs) with weak electron-donation ability are used to regulate the solvation structure to stabilize the electrolytes. As an example, we design the LiNO3 -DMSO@PC electrolyte, where DMSO acts as an HDNS and PC serves as an LDNS. This electrolyte exhibits excellent electrochemical compatibility with graphite anodes, as well as the LiFePO4 and LiCoO2 cathodes, leading to stable cycling over 200 cycles. Through spectroscopy analyses and theoretical calculation, we uncover the underlying mechanism responsible for the stabilization of these electrolytes. Our findings provide valuable insights into the preparation of LiNO3 -based electrolytes using the EDM rule, opening new avenues for the development of advanced electrolytes with versatile functions for sustainable rechargeable batteries.

Nanoporous graphene-based thin-film microelectrodes for in vivo high-resolution neural recording and stimulation

One of the critical factors determining the performance of neural interfaces is the electrode material used to establish electrical communication with the neural tissue, which needs to meet strict electrical, electrochemical, mechanical, biological and microfabrication compatibility requirements. This work presents a nanoporous graphene-based thin-film technology and its engineering to form flexible neural interfaces. The developed technology allows the fabrication of small microelectrodes (25 µm diameter) while achieving low impedance (∼25 kΩ) and high charge injection (3–5 mC cm−2). In vivo brain recording performance assessed in rodents reveals high-fidelity recordings (signal-to-noise ratio >10 dB for local field potentials), while stimulation performance assessed with an intrafascicular implant demonstrates low current thresholds (<100 µA) and high selectivity (>0.8) for activating subsets of axons within the rat sciatic nerve innervating tibialis anterior and plantar interosseous muscles. Furthermore, the tissue biocompatibility of the devices was validated by chronic epicortical (12 week) and intraneural (8 week) implantation. This work describes a graphene-based thin-film microelectrode technology and demonstrates its potential for high-precision and high-resolution neural interfacing.

Comparative analysis of thermal stability and electrochemical performance of NaNi1/3Fe1/3Mn1/3O2 cathode in different electrolytes for sodium ion batteries

The electrochemical compatibility and thermal stability of cathode and electrolyte guarantee the intrinsic safety of batteries. The NaNi1/3Fe1/3Mn1/3O2 (NaNFM) cathode for sodium ion batteries (SIBs) has not received, sufficient attention concerning its thermal safety compared to its electrochemical properties. Herein, we investigated the thermal stability of NaNFM, exothermic reaction and electrochemical performance of NaNFM with various electrolytes. The comprehensive electrochemical performance of NaNFM in different electrolytes followed this sequence: sodium hexafluorophosphate (NaPF6) > sodium bis(trifluoromethyl-sulfonyl)imide (NaTFSI) > sodium perchlorate (NaClO4)- based electrolytes. Additionally, ethylene carbonate (EC): propylene carbonate (PC)- type electrolytes displayed superior cycling stability compared to ethylene carbonate (EC): diethyl carbonate (DEC)- type electrolytes. Moreover, the heat flow profiles demonstrated that the thermal stability between NaNFM and various electrolytes could be ordered according to the total heat release as: NaClO4 < NaPF6 < NaTFSI-based electrolyte. X-ray diffractometer (XRD), scanning electron microscope (SEM) and x-ray photoelectron spectrometer (XPS) analyses were carried out to investigate the changes in crystal structure, morphology and valence state of thermal reaction products after microcalorimetric analysis experiments. These findings provide valuable insights for the safe application of the NaNFM cathode in SIBs.

Interfacial Degradation Processes in Solid-State Batteries during High Temperature Processing and the Mitigation Strategies

Garnet-type solid electrolytes have been extensively investigated in recent times as potential candidates for solid-state batteries. Among them, garnets with nominal composition Li7La3Zr2O12(LLZO) have received particular attention due to their high Li-ion conductivity (10-3 Scm-1) at room temperature and chemical stability against metallic lithium besides possessing a large electrochemical window >5V.[1] Despite of striking properties, LLZO suffers from several challenges such as interfacial instability with cathodes, e.g., LCO, during high temperature processing, resulting in a huge interface resistance, which is one of the fundamental reasons for the failure of solid-state batteries based on LLZO.[2-4] So far, the high interfacial impedance has been related to LLZO|LCO interface decomposition occurring due to diffusion of Co across the cathode-electrolyte interface. Herein, we investigated the hypothesis that interfacial degradation originate from the incorporation of Co into the LLZO lattice. The solubility limit of Co is determined to be 0.16 per formula unit, whilst the concentrations beyond promote phase transition (cubic LLZO-to-tetragonal LLZO). We investigated in detail the temperature-dependent Co diffusion into LLZO and concluded that detrimental cross diffusion could take place at any relevant process condition. Besides, the optimal protective Al2O3 coating thickness for relevant temperatures was studied, which allowed to create a process diagram to provide mitigation strategies towards enabling stable LCO|LLZO interface in all-solid-state batteries. Keywords: Solid-state batteries, Interfaces, cross diffusion, interfacial degradation AcknowledgementsD.R. acknowledges financial support by the Austrian Federal Ministry for Digital and Economic Affairs, the National Foundation for Research, Technology and Development and the Christian Doppler Research Association (Christian Doppler Laboratory for Solid-State Batteries). D.R. and J. F. acknowledges financial support by the Austrian Science Fund (FWF) in the frame of the project InterBatt (P 31437). D.K. acknowledges funding by the European Union’s Horizon 2020 Research and Innovation Programme (Grant No. 823717, project “ESTEEM3”) and by the Zukunftsfond Steiermark.Reference[1] Murugan, R., Thangadurai, V. and Weppner, W., 2007. Fast Lithium Ion Conduction in Garnet‐type Li7La3Zr2O12. Angew. Chemie. Int. Edt., 46(41), 7778-7781.[2] Chen, X., Xie, J., Zhao, X., & Zhu, T., 2021. Electrochemical Compatibility of Solid‐State Electrolytes with Cathodes and Anodes for All‐Solid‐State Lithium Batteries: A Review. Adv. Energy Sustain. Res., 2(5), 2000101.[3] Sakuda, A., Hayashi, A., Tatsumisago, M., 2010. Interfacial Observation Between LiCoO2 Electrode and Li2S-P2S5 Solid Electrolytes of All-Solid-State Lithium Secondary Batteries Using Transmission Electron Microscopy. Chem. Mater., 22(3), 949–956.[4] Ihrig, M., Kuo, L.Y., Lobe, S., Laptev, A.M., Lin, C.A., Tu, C.H., Ye, R., Kaghazchi, P., Cressa, L., Eswara, S. and Lin, S.K., 2023. Thermal Recovery of the Electrochemically Degraded LiCoO2/Li7La3Zr2O12: Al, Ta Interface in an All-Solid-State Lithium Battery. ACS Appl. Mater. Interfaces.

Hierarchical Mn3O4/NiSe2-MnSe2: A Versatile Electrode Material for High-Performance All-Solid-State Hybrid Pseudocapacitors with Supreme Working Durability.

As highly efficient electrochemical energy storage devices are in indispensable demand for numerous modern-day technologies, herein sluggish precipitation followed by an anion exchange procedure has been developed to synthesize an oxide-selenide mixed phase (Mn3O4/NiSe2-MnSe2) novel electrode material with high surface area and porosity for high-performance all-solid-state hybrid pseudocapacitors (ASSHPC). Mn3O4/NiSe2-MnSe2 shows a rich Tyndall effect (in H2O) and possesses randomly arranged low-dimensional crystallites of nearly similar size and uniform shape. The electrochemical analyses of Mn3O4/NiSe2-MnSe2 corroborate good electrochemical reversibility during charge transfer, superior pseudocapacitive charge-storage efficiency, and very low charge transfer and series resistance, ion-diffusion resistance, and relaxation time, which endorse the quick pseudocapacitive response of the material. The Mn3O4/NiSe2-MnSe2||N-rGO ASSHPC device demonstrates excellent charge-storage physiognomies suggestive of rich electrochemical and electromicrostructural compatibility between the electrode materials in the fabricated assembly. The Mn3O4/NiSe2-MnSe2||N-rGO ASSHPC device delivers high mass and area specific capacitance/capacity, very low charge-transfer resistance (∼0.74 Ω), total series resistance (∼0.76 Ω), diffusion resistance, and a relaxation time constant, which endorse the quick pseudocapacitive response of the device. The device delivers higher energy and power density (∼34 W h kg-1 at ∼2994 W kg-1), rate efficiency (∼17 W h kg-1 at ∼11,995 W kg-1), and cyclic performance (∼97.2% specific capacity/capacitance retention after 9500 continuous GCD cycles). The superior Ragone and cyclic efficiencies of the ASSHPC device are ascribed to the multiple redox-active Ni and Mn ions which lead to the supplemented number of redox reactions; "electroactive-ion buffering pool"-like physiognomics of Mn3O4/NiSe2-MnSe2, which facilitate the electrolyte ion dissemination to the electroactive sites even at high rate redox condition; and ideal electro-microstructural compatibility between the electrode materials, which leads to assisted charge transfer and absolute ion dissemination during the charge-storage process.