Electrical Injection Research Articles

Efficient heat dissipation perovskite lasers using a high-thermal-conductivity diamond substrate

Efficient heat dissipation that can minimize temperature increases in device is critical in realizing electrical injection lasers. High-thermal-conductivity diamonds are promising for overcoming heat dissipation limitations for perovskite lasers. In this study, we demonstrate a perovskite nanoplatelet laser on a diamond substrate that can efficiently dissipate heat generated during optical pumping. Tight optical confinement is also realized by introducing a thin SiO2 gap layer between nanoplatelets and the diamond substrate. The demonstrated laser features a Q factor of ∼1962, a lasing threshold of 52.19 µJ cm−2, and a low pump-density-dependent temperature sensitivity (∼0.56 ± 0.01 K cm2 µJ−1) through the incorporation of the diamond substrate. We believe our study could inspire the development of electrically driven perovskite lasers.

Experimental demonstration of electrical spin injection into semiconductor employing conventional three-terminal and non-local Hanle devices using spin gapless semiconductor as ferromagnetic injector

Here, the deposition of a polycrystalline thin film of a noble promising alloy Ti2CoSi (TCS) on a p-Si substrate has been reported, and its spin gapless semiconducting characteristics have been investigated experimentally. The structural, magnetic, and electronic transport features of the TCS film have been investigated in detail followed by its implementation as a ferromagnetic tunnel contact for proficient spin accumulation into a semiconductor employing both conventional three-terminal and non-local (NL) Hanle measurements. As we can avoid noticing erroneous effects like anisotropic magnetoresistance of the ferromagnetic electrodes, the NL-Hanle experiment has been established to be the most effective method for demonstrating true spin transport in semiconductors.

Relative phase locking of a terahertz laser system configured with a frequency comb and a single-mode laser

Stable operation is one of the most important requirements for a laser source for high-precision applications. Many efforts have been made to improve the stability of lasers by employing various techniques, e.g., electrical and/or optical injection and phase locking. However, these techniques normally involve complex experimental facilities. Therefore, an easy implementation of the stability evaluation of a laser is still challenging, especially for lasers emitting in the terahertz (THz) frequency range because the broadband photodetectors and mature locking techniques are limited. In this work, we propose a simple method, i.e., relative phase locking, to quickly evaluate the stability of THz lasers without a need of a THz local oscillator. The THz laser system consists of a THz quantum cascade laser (QCL) frequency comb and a single-mode QCL. Using the single-mode laser as a fast detector, heterodyne signals resulting from the beating between the single-mode laser and the comb laser are obtained. One of the heterodyne beating signals is selected and sent to a phase-locked loop (PLL) for implementing the relative phase locking. Two kinds of locks are performed by feeding the output error signal of the PLL, either to the comb laser or to the single-mode laser. By analyzing the current change and the corresponding frequency change of the PLL-controlled QCL in each phase-locking condition, we, in principle, are able to experimentally compare the stability of the emission frequency of the single-mode QCL (fs) and the carrier envelope offset frequency (fCEO) of the QCL comb. The experimental results reveal that the QCL comb with the repetition frequency injection locked demonstrates much higher stability than the single-mode laser. The work provides a simple heterodyne scheme for understanding the stability of THz lasers, which paves the way for the further locking of the lasers and their high-precision applications in the THz frequency range.

QUANTITATIVE ANALYSIS OF ELECTRICAL CURRENT EFFECT ON MAGNETIC RESONANCE IMAGE TISSUE INTENSITY

Recent studies in magnetic resonance imaging (MRI) aim to improve image quality while reducing scan time. Electrical current injection in the form of magnetic resonance electrical impedance tomography (MREIT) is believed to be affecting image quality and scan time thus can improve the possibility of becoming a non-chemical contrast agent in MRI. This study will observe and analyze the effect of electrical current injection on a phantom object to determine whether there is a different tissue image intensity. A thigh of lamb was used as a biological tissue phantom. The scan was performed on both T1and T2-weighted without and with an electrical current injection of 0.5 mA Electrical current injection decreased mean of tissue image intensity on T1-weighted images on both muscle (1759 vs 794) and bone (2752 vs 1550) (p<0.05). On the other hand, the electrical current increased mean of tissue image intensity on T2-weighted images on both muscle (303 vs 897) and bone (579 vs 1499) (p<0.05). There is also a difference in tissue image intensity on both T1 and T2-weighted images with and without electrical current injection on bone and muscle. The implication of this difference in image quality is a subject for further study.

Gain recovery dynamics in active type-II semiconductor heterostructures

Type-II heterostructures as active layers for semiconductor laser devices combine the advantages of a spectrally broad, temperature stable, and efficient gain with the potential for electrical injection pumping. Their intrinsic charge carrier relaxation dynamics limit the maximum achievable repetition rates beyond any constraints of cavity design or heat dissipation. Of particular interest are the initial build up of gain after high-energy injection and the gain recovery dynamics following depletion through a stimulated emission process. The latter simulates the operation condition of a pulsed laser or semiconductor optical amplifier. An optical pump pulse injects hot charge carriers that eventually build up broad spectral gain in a model (Ga,In)As/GaAs/Ga(As,Sb) heterostructure. The surplus energies of the optical pump mimic the electron energies typical for electrical injection. Subsequently, a second laser pulse tuned to the broad spectral gain region depletes the population inversion through stimulated emission. The spectrally resolved nonlinear transmission dynamics reveal gain recovery times as fast as 5 ps. These data define the intrinsic limit for the highest laser repetition rate possible with this material system in the range of 100 GHz. The experimental results are analyzed using a microscopic many-body theory identifying the origins of the broad gain spectrum.

The Utilization of a Coupled Electro-Thermal-Mechanical Model of High-Voltage Electric Pulse on Rock Fracture

Our research proposes a unique coupled electro-thermal-mechanical model that takes electric breakdown and heterogeneity into account to show the mechanism of rock fracturing under high-voltage electropulses. Using finite element numerical software, the process of high voltage electrical pulse injection into the rock interior for breakdown is described, and the formation law of plasma channels during the electrical breakdown process is comprehensively analyzed in conjunction with the conductor particles present within the rock. On the basis of electrical, thermal, and mechanical theories, a coupled multi-physical field numerical model of rock failure under the action of high-voltage electrical pulses is developed, and a random distribution model is utilized to simulate the potential occurrence of conductor particles in the rock. Innovative numerical model indicates plasma channel creation in the rock-crushing process. Prior to the formation of the plasma channel, the temperature and stress are approximately 103 k and 10-2 MPa, respectively. Once the plasma channel is formed, the temperature and stress increase abruptly in a short time, with the temperature reaching 104 k and the stress reaching 103 MPa or higher. In addition, it is revealed that the breakdown field strength is the essential factor in plasma channel creation. The heterogeneity of the particles within the rock and the fluctuation in electrode settings are also significant variables influencing the creation of channels. The presented model contributes to a better understanding of the mechanism of rock fragmentation during high-voltage electrical pulses, which has substantial implications for oil exploration and mineral extraction.

Operation Recommendations for Tension Joints and Clamps on a 63 kV Overhead Transmission Line Conductor Based on Experimental Tests

This study provides the operation recommendations for the tension fittings used on a 63 kV overhead transmission line conductor based on experimental tests. In this way, the tension fittings, including the dead-end clamp, the mid-span joint, and the repair sleeve, are assembled on the lynx conductor under different faulty and healthy assembly conditions in the laboratory. The lynx conductor is one of the widely used conductors in the 63 kV overhead power lines. The electric current injection test, along with thermal imaging and also tensile test, are conducted on the studied samples. The results show that the surface temperature of the lynx conductor is higher than the surface temperatures of the dead-end clamp and mid-span joint under normal and overload current conditions. Also, the crimping pressure of the aluminum and steel pipes less than the standard value, the crimping length of the steel cores of conductor less than the standard value, and the crimping length of the aluminum pipes more than the standard value can lead to a developmental defect which should be repaired or replaced at the first opportunity of the transmission line service outage. The repair sleeve is under more thermal stress than the dead-end clamp and mid-span joint, even in the standard assembly condition. A slight temperature difference of a repair sleeve compared with the same type fitting may be a severe operating condition. Also, the use of two consecutive repair sleeves to cover the conductor cut strands is not recommended. Furthermore, the loose connection of bolts at the junction of the jumper terminal to the dead-end clamp causes a very high temperature which should be repaired immediately. If the temperature difference between two defective and healthy dead-end clamp or mid-span joint is more than 13 °C, a critical defect is diagnosed; however, the temperature difference between two repair sleeve more than 7 °C indicates a critical operation condition for defective one.

Strain visualization enabled in dual-wavelength InGaN/GaN multiple quantum wells Micro-LEDs by piezo-phototronic effect

Optical strain sensor for stress visualization is a significant topic in biomechanical imaging or electronic skin. In this study, the dual-wavelength InGaN/GaN multiple-quantum-wells (MQWs) micro light emitting diode (Micro-LED) is demonstrated with color response under mechanical stimulation by piezo-phototronic effect. The peak intensity of green light increases by about 37%, while the blue decreases by 10% at the external strain of 0.20%. Simultaneously, the intensity integral ratio of green and blue light changes from 43:57–53:47, leading to the display color shift from light blue to turquoise significantly. It is noted that electrical injection shows a greater color response than photoluminescence, indicating that the piezo-phototronic effect changes both the recombination in MQWs and the carrier injection. The different piezoelectric modulation between green QW and blue QW lies on the different strain-induced piezoelectric polarized charges in the interface of InGaN QWs, revealed by experiments and APSYS simulation in details. This study is of high significance for the development of optical-based stress sensor with strain visualization and high spatial resolution for smart sensing and micro-opto-electromechanical systems.

Technical-Economic Evaluation of Residential Wind and Photovoltaic Systems with Self-Consumption and Storage Systems in Portugal

At present, a worldwide paradigm shift has become apparent, with more and more consumers consuming the energy generated by renewable energy sources (RES) systems, such as wind or photovoltaic (PV) energy, sometimes benefiting from appropriate incentives by individual governments. Consequently, it is necessary to carry out technical–economic assessments to understand the evolution of the viability of RES investments. Within the framework of an intelligent network control environment, the smart grid (SG) concept is associated with this model, and is an important tool in the management of energy distribution networks. This article aims to make a further contribution to this issue by analyzing the economic feasibility of investing in residential consumers, considering different RES configurations. Scenarios covered in this study include: “inject all on the low voltage network/consume all on the low voltage network”, self-consumption, net-metering, and storage systems. The economic study results in this article show that self-consumption with and without the injection of excess electricity into the grid is quite attractive. The bi-hourly tariff was found to be more profitable than other tariffs. Variable tariffs (bi or tri-hourly) are more profitable than fixed tariffs. It is also concluded that investment in storage systems is not yet an economically viable solution due to the high price of energy storage.

Non‐Equilibrium Bose–Einstein Condensation of Exciton‐Polaritons in Silicon Metasurfaces

AbstractExciton‐polaritons (EPs) are hybrid light–matter quasi‐particles with bosonic character formed by the strong coupling between excitons in matter and photons in optical cavities. Their hybrid character offers promising prospects for the realization of non‐equilibrium Bose–Einstein condensates (BECs), and room‐temperature BECs are possible with organic materials. However, the thresholds required to create BECs of organic EPs remain still high to allow condensation with electrical injection of carriers. One of the factors behind these high thresholds is the very short cavity lifetimes, leading to a fast EP decay and the need to inject higher exciton densities in the reservoir to form the condensate. Here a BEC of EPs in organic dyes and all‐dielectric metasurfaces at room temperature is demonstrated. By using dielectric metasurfaces that exhibit very low losses it is possible to achieve cavity lifetimes long enough to allow an efficient population of EP states via vibrational relaxation and radiative pumping. It is shown how polariton lasing or non‐equilibrium Bose–Einstein condensation is achieved in several cavities, and one of the lowest reported thresholds for BECs in organic materials is observed.

Vacuum Spin LED: First Step towards Vacuum Semiconductor Spintronics.

Improving the efficiency of spin generation, injection, and detection remains a key challenge for semiconductor spintronics. Electrical injection and optical orientation are two methods of creating spin polarization in semiconductors, which traditionally require specially tailored p-n junctions, tunnel or Schottky barriers. Alternatively, we introduce here a novel concept for spin-polarized electron emission/injection combining the optocoupler principle based on vacuum spin-polarized light-emitting diode (spin VLED) making it possible to measure the free electron beam polarization injected into the III-V heterostructure with quantum wells (QWs) based on the detection of polarized cathodoluminescence (CL). To study the spin-dependent emission/injection, we developed spin VLEDs, which consist of a compact proximity-focused vacuum tube with a spin-polarized electron source (p-GaAs(Cs,O) or Na2KSb) and the spin detector (III-V heterostructure), both activated to a negative electron affinity (NEA) state. The coupling between the photon helicity and the spin angular momentum of the electrons in the photoemission and injection/detection processes is realized without using either magnetic material or a magnetic field. Spin-current detection efficiency in spin VLED is found to be 27% at room temperature. The created vacuum spin LED paves the way for optical generation and spin manipulation in the developing vacuum semiconductor spintronics.

High-temperature continuous-wave operation of 1310 nm InAs/GaAs quantum dot lasers

Here we report 1.3 μm electrical injection lasers based on InAs/GaAs quantum dots (QDs) grown on a GaAs substrate, which can steadily work at 110 °C without visible degradation. The QD structure is designed by applying the Stranski–Krastanow growth mode in solid source molecular beam epitaxy. The density of InAs QDs in the active region is increased from 3.8 × 1010 cm−2 to 5.9 × 1010 cm−2. As regards laser performance, the maximum output power of devices with low-density QDs as the active region is 65 mW at room temperature, and that of devices with the high-density QDs is 103 mW. Meanwhile the output power of high-density devices is 131 mW under an injection current of 4 A at 110 °C.

Probing the stability of perovskite solar cell under working condition through an ultra-thin silver electrode: Beyond the halide ion diffusion and metal diffusion

Perovskite solar cells (PSCs) with an excellent optoelectronic performance have intrigued mushrooming research interests, and the undesirable intrinsic stability of halide perovskite materials still remains a severe constraint for their practical application. Fortunately, the ambiguous and complicated incentives for the degradation process of PSCs under working condition can be directly reflected on the corrosion of silver electrode by halogens. Here, a new perspective for evaluating the long-term stability of PSCs is presented by the time-dependent transverse resistance of the ultrathin silver electrode under different working conditions. Being anode or cathode, the stability of ultra-thin silver layer has been systematically investigated through adjusting the external operating conditions of devices, i.e. light illumination and bias voltage. Experimental results indicate that the gradual resistance increases of silver film can be attributed to the oxidation of I− existing on the top surface of perovskite layer by non-equilibrium holes generated from light illumination or electrical injection for producing corrosive I2 gas, which will diffuse through the carrier transporting layer and attack the thin silver layer. The interaction probability of I− and non-equilibrium holes at the interface plays a critical role on the generation of I2 gas and resistance variation of the top thin silver electrode. The stability study of electrode indicator will shed light on the ambiguous degradation mechanisms of PSC under working condition, paving a path for conquering the fatal problems of the practical application.

Comparative Analysis between Proportional-Integral and Artificial Neural Network Control of a Grid-Connected PV System

This article presents a comprehensive analysis of the modeling and control techniques applied to a photovoltaic (PV) system that is connected to a three-phase grid. To successfully integrate the PV system with the electrical grid, an innovative and reliable controller has been designed and put into practice. The utilization of an artificial neural network (ANN) enables the system to optimize power extraction from the PV panels, benefiting from the ANN's resilience and swift response to varying conditions. Moreover, a robust proportional-integral (PI) control strategy is introduced to govern the grid-side operations. This strategy of action focuses on managing the injection of both active and reactive electricity into the grid as well as controlling the voltage of the DC bus. A series of detailed simulations were carried out evaluating the efficiency of the suggested control strategy in the MATLAB/SIMULINK. The results obtained from these simulations share insightful information on the effectiveness and efficiency of the control system in ensuring optimal operation and power management of the PV system within the grid-connected setup.

Electrically driven free shear flows in a duct under a transverse uniform magnetic field

A mathematical model of two-dimensional electrically driven laminar plane free shear flows in a straight duct under the action of an applied spanwise uniform magnetic field is considered. The mathematical approach is like that used in the research of Hunt and Williams (J. Fluid. Mech., 31, 705, 1968) and Kolesnikov and Kalis (Magnetohydrodynamics, vol. 57, 2021, no. 2). A system of stationary partial differential equations with two unknown functions of velocity and induced magnetic field is solved. The electric current is injected into the liquid by means of two couples of linear electrodes located vis-à-vis on opposite duct walls, perpendicular to the magnetic field. Three cases are considered. One pair of electrodes is current supplied and, depending on the direction of electric current injection on the electrode pair, two coinciding or two counter flows are also driven. At Hartmann numbers Ha >> 1, quasi-potential cores are formed in these flows, bounded by lateral Shercliff free boundary layers parallel to the field and two Hartmann layers on the walls perpendicular to the field. As a result, almost all of the injected current passes through these layers. An increase of the magnetic field leads only to an internal rearrangement of the potential cores of the flows. The Hartmann number varies in the range from 1 to 100. Figs 15, Refs 11.

Transforming Navier‐stokes equation to a fourth order nonlinear differential equation for the study of electrolyte flow in a circular microchannel

AbstractIn this paper, analytical solutions are derived for the study of steady‐state electrolyte flow in a circular microchannel under the simultaneous effects of an external electric field and uniform wall injection. The Navier‐Stokes equations containing an axial linear electric body force are transformed to a fourth‐order nonlinear differential equation and solved analytically using a series solution method. The most important results are presented and discussed in terms of radial Reynolds number and a fundamental non‐dimensional electric field parameter. The Electrical Double Layer theory is employed to model the effects of external electric field. Analytical relations are given for velocity profiles, exit flow rate, and total pressure drop in the microchannel. The results show that a high‐intensity electric field can completely reverse the velocity profile or make it more flat in the presence of wall injection. This electric effect can be used in practical applications to control the shear stress, heat, or mass transfer in microchannels or microelectromechanical systems. In addition, various graphs are presented showing simultaneous effects of electric field and wall injection of the same fluid on the flow physics.

Effective spin injection into the organic semiconductor PTCDA evaluated by a normalization method

Studies of spin current injection, transport, and interface control have drawn attention recently for efficient organic spintronic devices. In this study, we apply both spin pumping (SP) and the longitudinal spin Seebeck effect (LSSE) to inject spin currents into a π-conjugated organic semiconductor, perylene-3,4,9,10-tetracarboxylic dianhydride (PTCDA), and characterize injection and transport by measuring inverse spin Hall voltage VISHE in spin detectors. A normalization factor introduced to SP analysis eliminates a contribution provoked by deviation of spin sources and leads to a more accurate determination of the spin diffusion length in PTCDA. While SP with Permalloy as a spin source is effective in generating detectable VISHE, the LSSE from yttrium iron garnet shows no convincing sign of spin injection. In addition, spin-flip scattering induced by hybrid states undermining electrical spin injection is negligible in SP. These results are attributed to interfaces between spin sources and PTCDA, indicative of the importance of injection methods and material choices.

Nonlinear Quantum Photonics With AlGaAs Bragg-Reflection Waveguides

Integrated photonics is playing a key role in the development of quantum technologies covering applications ranging from quantum communication to computing and from simulations to sensing. In this context, material platforms enabling the chip-scale integration of quantum components are a key issue on the way towards real-world and large-scale technological implementations. In this paper, we review our last achievements on AlGaAs Bragg reflection waveguides emitting nonclassical states of light by spontaneous parametric down conversion. The choice of this platform combines the advantages of a mature fabrication technology, room temperature operation, emission in the telecom C-Band and compliance with electrical injection. We demonstrate the ability of these devices to generate a large variety of quantum states spanning from biphoton frequency combs to broadband polarization entanglement enabling promising applications in quantum processing as well as flexible quantum networks.

High current limits in chemical vapor deposited graphene spintronic devices

Understanding the stability and current-carrying capacity of graphene spintronic devices is key to their applications in graphene channel-based spin current sensors, spin-torque oscillators, and potential spin-integrated circuits. However, despite the demonstrated high current densities in exfoliated graphene, the current-carrying capacity of large-scale chemical vapor deposited (CVD) graphene is not established. Particularly, the grainy nature of chemical vapor deposited graphene and the presence of a tunnel barrier in CVD graphene spin devices pose questions about the stability of high current electrical spin injection. In this work, we observe that despite structural imperfections, CVD graphene sustains remarkably highest currents of 5.2 × 108 A/cm2, up to two orders higher than previously reported values in multilayer CVD graphene, with the capacity primarily dependent upon the sheet resistance of graphene. Furthermore, we notice a reversible regime, up to which CVD graphene can be operated without degradation with operating currents as high as 108 A/cm2, significantly high and durable over long time of operation with spin valve signals observed up to such high current densities. At the same time, the tunnel barrier resistance can be modified by the application of high currents. Our results demonstrate the robustness of large-scale CVD graphene and bring fresh insights for engineering and harnessing pure spin currents for innovative device applications.

Study of the influence of the parameters of preparation of polymeric solutions obtaining nanofibers by electrospinning

The technique of electrospinning polymeric nanofibers has been emerging in the academic environment due to its well-parias and low operational, but the production of these nanofibers finds challenges regarding homogeneity and reproduction of obtained results. As properties of polymeric solutions are important for the determination of electrospinning parameters, such as the applied electrical voltage and injection rate. Seeking rheological behavior of polymeric solutions; which may be affected by the concentration of the polymeric solution and the preparation temperature of these solutions. This way this work studied the effect of the production temperature of polyacrylonitrile and methyl acrylate copolymer solutions and related them to the nanofibers produced at the same injection rates and electrical stresses. It was observed the inversely proportional behavior between the temperature of preparation of the solutions and the viscosity of the solutions at room temperature, which reflects in the integrity and homogeneity of the fibers formed, with the formation of pearls in the nanofibers produced to more viscous solutions.