Efficient Charge Generation Research Articles

Sensitive Self-Driven Single-Component Organic Photodetector Based on Vapor-Deposited Small Molecules.

Typically, organic solar cells (OSCs) and photodetectors (OPDs) comprise an electron donating and accepting material to facilitate efficient charge carrier generation. This approach has proven successful in achieving high-performance devices but has several drawbacks for upscaling and stability. This study presents a fully vacuum-deposited single-component OPD, employing the neat oligothiophene derivative DCV2-5T in the photoactive layer. Free charge carriers are generated with an internal quantum efficiency of 20 % at zero bias. By optimizing the device structure, a very low dark current of 3.4 · 10-11Acm-2 at -0.1V is achieved, comparable to the dark current of state-of-the-art bulk heterojunction OPDs. This optimization results in specific detectivities of 1· 1013Jones (based on noise measurements), accompanied by a fast photoresponse (f-3dB = 200kHz) and a broad linear dynamic range (>150dB). Ultrafast transient absorption spectroscopy unveils that charge carriers are already formed at very short time scales (<1ps). The surprisingly efficient bulk charge generation mechanism is attributed to a strong electronic coupling of the molecular exciton and charge transfer states. This work demonstrates the very high performance of single-component OPDs and proves that this novel device design is a successful strategy for highly efficient, morphological stable and easily manufacturable devices.

Correlation between the Molecular Properties of Semiconducting Polymers of Intrinsic Microporosity and Their Photocatalytic Hydrogen Production.

Increasing the interface area between organic semiconductor photocatalysts and electrolyte by fabricating nanoparticles has proven to be an effective strategy to increase photocatalytic hydrogen production activity. However, it remains unclear if increasing the internal interface by the introduction of porosity has as clear benefits for activity. To better inform future photocatalyst design, a series of polymers of intrinsic microporosity (PIMs) with the same conjugated backbone were synthesized as a platform to independently modulate the variables of porosity and relative hydrophilicity through the use of hydrophilic alcohol moieties protected by silyl ether protecting groups. When tested in the presence of ascorbic acid and photodeposited Pt, a strong correlation between the wettable porosity and photocatalytic activity was found, with the more wettable analogue of two polymers of almost the same surface area delivering 7.3 times greater activity, while controlling for other variables. Transient absorption spectroscopic (TAS) investigation showed efficient intrinsic charge generation within 10 ps in two of the porous polymers, even without the presence of ascorbic acid or Pt. Detectable hole polarons were found to be immediately extracted by added ascorbic acid, suggesting the generation of reactive charges at regions readily accessible to electrolyte in the porous structures. This study directs organic semiconductor photocatalysts design toward more hydrophilic functionality for addressing exciton and charge recombination bottlenecks and clearly demonstrates the advantages of wettable porosity as a design principle.

MoS2/porous carbon nanofiber heterostructures for efficient evaporation-driven generators.

Evaporation power generators (EPGs) based on natural water evaporation can directly convert heat energy from the surrounding environment into electrical energy. However, EPGs are difficult to commercialize due to the low charge generation and transport efficiency of single material systems, resulting in unsatisfactory open-circuit voltages and short-circuit currents. Here, we step by step prepared MoS2/porous carbon nanofiber (PCNF) heterogeneous systems by electrospinning and hydrothermal methods. Electron microscope measurements proven the uniform coating of high-crystalline quality MoS2 nanosheets on PCNF fabrics, and the uneven concave-convex surface increased the specific surface area. MoS2 covered PCNF fabrics retained good hydrophilicity, which was suitable for absorbing water and keeping the surface wet during long-term evaporation. Moreover, layered MoS2 with rich surface charge improved the charge transfer of the MoS2/PCNF fabrics. As a result, the open-circuit voltage and short-circuit current of the EPGs prepared with MoS2/PCNF fabrics were improved to 0.25 V and 75 μA, respectively, compared with those based on PCNF fabrics, which demonstrated that the MoS2 coatings improved the interaction area with water and the charge transfer effect of the EPGs. This heterogeneous combination strategy provides ideas for the preparation of high-performance EPG materials.&#xD.

Efficient Derivatization of a Thienobenzobisthiazole-Based π-Conjugated Polymer Through Late-Stage Functionalization Towards High-Efficiency Organic Photovoltaic Cells.

Derivatization is essential for optimizing organic material properties. However, because functional groups are often introduced at an early stage of the synthesis, similar intermediates have to be repeatedly synthesized to produce derivatives, which amounts to a daunting and time-consuming task. Using thienobenzobisthiazole (TBTz) as a building unit of donor polymers for organic photovoltaics (OPVs), we demonstrate an efficient derivatization of a TBTz-based π-conjugated polymer by late-stage functionalization. In the developed synthetic route, functional groups are introduced at the last step of monomer synthesis, enabling us to easily synthesize several derivatives from a common intermediate. Ester and acyl groups are introduced into the polymer instead of the alkyl group, giving rise to deep HOMO energy levels and resulting in OPV cells with high open-circuit voltage even in the absence of halogen substituents that are typically introduced into the donor polymers. Notably, the ester-functionalized TBTz-based polymer shows a small nonradiative voltage loss (ΔVnr) of 0.19 V and has one of the highest charge generation efficiencies among the halogen-free donor polymers with similar ΔVnr, improving the critical trade-off relationship between voltage loss and charge generation. Our results provide an important guideline for the efficient development of high-performance polymers for OPVs.

Efficient Derivatization of a Thienobenzobisthiazole‐Based π‐Conjugated Polymer Through Late‐Stage Functionalization Towards High‐Efficiency Organic Photovoltaic Cells

AbstractDerivatization is essential for optimizing organic material properties. However, because functional groups are often introduced at an early stage of the synthesis, similar intermediates have to be repeatedly synthesized to produce derivatives, which amounts to a daunting and time‐consuming task. Using thienobenzobisthiazole (TBTz) as a building unit of donor polymers for organic photovoltaics (OPVs), we demonstrate an efficient derivatization of a TBTz‐based π‐conjugated polymer by late‐stage functionalization. In the developed synthetic route, functional groups are introduced at the last step of monomer synthesis, enabling us to easily synthesize several derivatives from a common intermediate. Ester and acyl groups are introduced into the polymer instead of the alkyl group, giving rise to deep HOMO energy levels and resulting in OPV cells with high open‐circuit voltage even in the absence of halogen substituents that are typically introduced into the donor polymers. Notably, the ester‐functionalized TBTz‐based polymer shows a small nonradiative voltage loss (ΔVnr) of 0.19 V and has one of the highest charge generation efficiencies among the halogen‐free donor polymers with similar ΔVnr, improving the critical trade‐off relationship between voltage loss and charge generation. Our results provide an important guideline for the efficient development of high‐performance polymers for OPVs.

The Rise of Tandem Perovskite Light-Emitting Diode.

In 2024, tandem perovskite light-emitting diodes (tandem-PLEDs) achieved a breakthrough external quantum efficiency of 43.42%, with an organic electroluminescence (EL) unit stacked atop a perovskite EL unit, surpassing the previous single-junction perovskite LEDs. This innovative design enables a higher brightness at lower currents, enhancing the longevity and efficiency of the tandem-PLEDs. Additionally, the tandem-PLEDs can also be fabricated by combining a perovskite EL unit with a perovskite quantum dot unit. In this perspective, the key advancements in tandem-PLEDs are highlighted, focusing on the development of perovskite-organic materials, perovskite-perovskite quantum dots, and the design principles for obtaining efficient and stable charge generation layers. But more importantly, the challenges and solutions are discussed in fabricating all-perovskite tandem LEDs using strongly polar solvents that have yet to be reported nowadays. This comprehensive guide aims to support researchers in advancing the practical deployment of tandem-PLED technology.

Molecular Control of the Donor/Acceptor Interface Suppresses Charge Recombination Enabling High-Efficiency Single-Component Organic Solar Cells.

Single-component organic solar cells based on double cable polymers have achieved remarkable performance, with DCPY2 reaching a high efficiency of over 13%. In this study, DCPY2 is further optimized with an efficiency of 13.85%, maintaining a high fill factor (FF) without compromising the short circuit current. Despite its intermixed morphology, DCPY2 shows a reduced recombination rate compared to their binary counterpart (PBDB-T:Y-O6). This slower recombination in DCPY2 is attributed to the reduced wavefunction overlap of delocalized charges, achieved by spatially separating the donor and acceptor units with an alkyl linker, thereby restricting the recombination pathways. Adding 1,8-diiodooctane (DIO) into DCPY2 further reduced the recombination rate by facilitating acceptor aggregation, allowing free charges to become more delocalized. The DIO-assisted aggregation in DCPY2 (5% DIO) is evidenced by an increased pseudo-pure domain size of Y-O6. Fine molecular control at the donor/acceptor interface in the double-cable polymer achieves reduced non-geminate recombination under efficient charge generation, increased mobility, and charge carrier lifetime, thereby achieving superior performance. Nevertheless, the FF is still limited by relatively low mobility compared to the blend, suggesting the potential for further mobility improvement through enhanced higher-dimensional packing of the double-cable material.

Design of Ultra-Narrow Bandgap Polymer Acceptors for High-Sensitivity Flexible All-Polymer Short-Wavelength Infrared Photodetectors.

All-polymer photodetectors possess unique mechanical flexibility and are ideally suitable for the application in next-generation flexible, wearable short-wavelength infrared (SWIR, 1000-2700 nm) photodetectors. However, all-polymer photodetectors commonly suffer from low sensitivity, high noise, and low photoresponse speed in the SWIR region, which significantly diminish their application potential in wearable electronics. Herein, two polymer acceptors with absorption beyond 1000 nm, namely P4TOC-DCBT and P4TOC-DCBSe, were designed and synthesized. The two polymers possess rigid structure and good conformational stability, which is beneficial for reducing energetic disorder and suppressing dark current. Owing to the efficient charge generation and ultralow noise current, the P4TOC-DCBT-based all-polymer photodetector achieved a specific detectivity () of over 1012 Jones from 650 (visible) to 1070 nm (SWIR) under zero bias, with a response time of 1.36 μs. These are the best results for reported all-polymer SWIR photodetectors in photovoltaic mode. More significantly, the all-polymer blend films exhibit good mechanical durability, and hence the P4TOC-DCBT-based flexible all-polymer photodetectors show a small performance attenuation (<4%) after 2000 cycles of bending to a 3 mm radius. The all-polymer flexible SWIR organic photodetectors are successfully applied in pulse signal detection, optical communication and image capture.

Design of Ultra‐Narrow Bandgap Polymer Acceptors for High‐Sensitivity Flexible All‐Polymer Short‐Wavelength Infrared Photodetectors

All‐polymer photodetectors possess unique mechanical flexibility and are ideally suitable for the application in next‐generation flexible, wearable short‐wavelength infrared (SWIR, 1000–2700 nm) photodetectors. However, all‐polymer photodetectors commonly suffer from low sensitivity, high noise, and low photoresponse speed in the SWIR region, which significantly diminish their application potential in wearable electronics. Herein, two polymer acceptors with absorption beyond 1000 nm, namely P4TOC‐DCBT and P4TOC‐DCBSe, were designed and synthesized. The two polymers possess rigid structure and good conformational stability, which is beneficial for reducing energetic disorder and suppressing dark current. Owing to the efficient charge generation and ultralow noise current, the P4TOC‐DCBT‐based all‐polymer photodetector achieved a specific detectivity () of over 1012 Jones from 650 (visible) to 1070 nm (SWIR) under zero bias, with a response time of 1.36 μs. These are the best results for reported all‐polymer SWIR photodetectors in photovoltaic mode. More significantly, the all‐polymer blend films exhibit good mechanical durability, and hence the P4TOC‐DCBT‐based flexible all‐polymer photodetectors show a small performance attenuation (&lt;4%) after 2000 cycles of bending to a 3 mm radius. The all‐polymer flexible SWIR organic photodetectors are successfully applied in pulse signal detection, optical communication and image capture.

(Digital Presentation) The Influence of Particle Size on Electrophotocatalytic Properties of Tungsten Trioxide Photoanodes

The need for advanced wastewater treatment technologies has been highlighted owing to the widespread contamination of water sources with toxic and persistent organic chemicals. Thin films of tungsten (VI) oxide (WO3) were prepared by spin-coating and meyer rod coating nanoparticulate dispersions following a top-down approach through ball milling. The morphological properties of the layers were investigated by profilometry. The results showed that the surface area increased with the increase in milling time and for 96 hours sample it showed a nine-fold increase compared to commercial tungsten (VI) oxide powder. The electron microscopic images provided insight into the change in particle size and layer texture which comply with the morphological changes observed by profilometry. The influence of the particle size on the charge generation efficiency was investigated using photoanodes prepared from the studied suspensions. Two distinct formulations of different particle sizes were mixed in variable ratios, and we showed that multimodal coatings exhibit larger photocurrents than monomodal coatings. The main contribution of this work can be found in the economically inexpensive method of preparing thin films WO3.

(Invited) Influence of Y6 Aggregation on Energetics and Charge Generation in High Performance OPV Blends

We investigated the origin of the high ratio of open circuit voltage to charge transfer state energy (eVOC/ECT) of OPV polymer blends consisting of the electron donating polymer PM6 and the non-fullerene electron acceptor Y6. PM6-Y6 and related donor-acceptor OPV blends exhibit remarkable optoelectronic properties and record power conversion efficiencies in part because of their unusually high eVOC/ECT ratios, which is believed to be related to the small energetic offset of the HOMO levels of PM6 and Y6. In this study, we varied the amount of Y6 in PM6 blends as a means to control the aggregation of Y6 molecules. We examined the corresponding influence that Y6 aggregation has on the energetic offsets and the charge generation efficiency of the materials by probing the appearance of polaron absorption signals in the mid-infrared using time-resolved infrared spectroscopy. Furthermore, we examined the optical absorption and emission spectra of the PM6-Y6 blends over the range of compositions to correlate the efficiency of charge generation with the signatures of Y6 aggregation in the optical spectra. We observed an abrupt transition around 30 mass% Y6 content at which polarons were efficiently generated by charge separation from PM6 to Y6. Comparison to composition dependent GIWAXS studies of PM6-Y6 blends revealed the formation of Y6 aggregates around the same 30 mass% threshold. These observations demonstrate that aggregation of Y6 molecules is required for charge separation to occur from PM6 to Y6 as measured through the mid-infrared absorption of polarons in the TRIR spectra. Although charges were efficiently generated in blends with only 30 mass% Y6 content, OPV device studies revealed that 50-60 mass% Y6 was needed to reach optimized short-circuit current and OPV device efficiency because these measurements convolve charge generation with charge transport. These findings clarify the optoelectronic properties of the novel class of Y6 acceptors and emphasize the importance of molecular aggregation for tuning the energetics of high performance systems that minimize energy offsets for maximum OPV power conversion efficiencies.

Bithieno[3,4-c]pyrrole-4,6-dione-Based Wide-Bandgap Donor Polymers for Efficient Polymer Solar Cells.

The polymer solar cells (PSCs) have garnered substantial interest owing to their lightweight, cost-effectiveness, and flexibility, making them ideal for large-scale roll-to-roll manufacturing. In this study, two wide-bandgap (WBG) donor polymers, PFBiTPD and PClBiTPD, utilizing bithieno[3,4-c]pyrrole-4,6-dione (BiTPD) as the electron-accepting unit and fluorinated/chlorinated benzo[1,2-b:4,5-b']dithiophene (BDT) as the electron-donating moiety are designed and synthesized. The polymers demonstrated large optical bandgaps (exceeding 1.80eV) and are blended with ITIC-4F to form the active layers in PSCs. The PFBiTPD-based devices showed a well-dispersed fibrillar network, facilitating efficient charge generation and transport. Thus, these devices attained a power conversion efficiency (PCE) of 8.60%, featuring a fill factor (FF) of 62.89%, an open-circuit voltage (Voc) of 0.88V and a short-circuit current density (Jsc) of 15.54mA cm-2. In contrast, PClBiTPD-based devices displayed lower performance due to less favorable morphology. The study underscores the importance of polymer design and morphology control in optimizing the photovoltaic performance of PSCs.

Influence of Particle Size on Electrophotocatalytic Properties of Tungsten Trioxide Photoanodes

The need for advanced wastewater treatment technologies has been highlighted by the widespread contamination of water sources with toxic and persistent organic chemicals. In this work, thin films of tungsten (VI) oxide (WO3) were prepared by spin-coating and Meyer rod coating nanoparticulate dispersions following a top-down approach through ball milling. The morphological properties of the layers were investigated by profilometry. The results showed that the surface area increased with an increase in milling time for the milled mixture, and, for the sample milled for 96 h, it showed a nine-fold increase compared to the commercial tungsten (VI) oxide powder. The electron microscopic images provided insight into the change in particle size and layer texture which comply with the morphological changes observed by profilometry. The influence of the particle size on the charge generation efficiency was investigated using photoanodes prepared from the studied suspensions. Two distinct formulations of different particle sizes were mixed in variable ratios, and we showed that multimodal coatings exhibit larger photocurrents than monomodal coatings. The main contribution of this work can be found in the economically inexpensive method of preparing thin films WO3.

Donor-acceptor bulk-heterojunction sensitizer for efficient solid-state infrared-to-visible photon up-conversion

Solid-state infrared-to-visible photon up-conversion is important for spectral-tailoring applications. However, existing up-conversion systems not only suffer from low efficiencies and a need for high excitation intensity, but also exhibit a limited selection of materials and complex fabrication processes. Herein, we propose a sensitizer with a bulk-heterojunction structure, comprising both an energy donor and an energy acceptor, for triplet-triplet annihilation up-conversion devices. The up-conversion occurs through charge separation at the donor-acceptor interface, followed by the formation of charge transfer state between the energy donor and annihilator following the spin statistics. The bulk-heterojunction sensitizer ensures efficient charge generation and low charge recombination. Hence, we achieve a highly efficient solid-state up-conversion device with 2.20% efficiency and low excitation intensity (10 mW cm−2) through a one-step solution method. We also demonstrate bright up-conversion devices on highly-flexible large-area substrates. This study introduces a simple and scalable platform strategy for fabricating efficient up-conversion devices.

Long exciton diffusion distance and efficient exciton dissociation enable high efficiency planar heterojunction non-fullerene organic solar cells

We characterized exciton diffusion and dissociation behaviour in two ITIC derivatives non-fullerene acceptors (NFA) by time-resolved spectroscopic methods. The exciton diffusion length was determined to be ∼26 and ∼34 nm in ITIC and IT4F. We further examined the dissociation of excitons in those NFA at the acceptor/donor planar heterojunction interfaces by transient absorption measurements, in which efficient charge generation was observed. Finally, we fabricated planar heterojunction solar cells using PM6/NFA bilayer planar heterojunctions; a power conversion efficiency (PCE) of over 7 % for PM6/IT4F bilayers was determined. More importantly, the spin-coating of top layer NFA has negligible influence on the morphology of the PM6 layer, suggesting a clear bilayer interface, rather than a quasi-bilayer structure with a portion of bulk heterojunction. The results suggest that enhanced exciton diffusion length and efficient exciton dissociation and charge generation are elemental characters to realize high PCE planar heterojunction organic solar cells. We established direct linking between the exciton diffusion length and the photocurrent generation in NFA layer by transfer matrix simulation. The large exciton diffusion length in NFAs makes the realization of high efficiency and stable bilayer organic solar cells feasible.

Efficient and Photostable Organic Solar Cells Achieved by Alloyed Dimer Acceptors with Tailored Linker Structures

AbstractHigh power conversion efficiency (PCE) and long‐term stability are prerequisites for commercialization of organic solar cells (OSCs). Herein, two dimer acceptors (DYTVT and DYTCVT) are developed with different properties through linker engineering, and study their effects as alloy‐like acceptors on the photovoltaic performance and photostability of OSCs. These ternary OSCs effectively combine the advantages of both dimer acceptors. DYTVT, characterized by its high backbone planarity, ensures elevated electron mobility and high glass‐transition temperature (Tg), leading to efficient charge transport and enhanced photostability of OSCs. Conversely, DYTCVT, with its significant dipole moment and electrostatic potential, enhances compatibility of the alloy acceptors with donors and refines the blend morphology, facilitating efficient charge generation in OSCs. Consequently, D18:DYTVT:DYTCVT OSCs exhibit higher PCE (18.4%) compared to D18:MYT (monomer acceptor, PCE = 16.5%), D18:DYTVT (PCE = 17.4%), and D18:DYTCVT (PCE = 17.0%) OSCs. Furthermore, owing to higher Tg of alloy acceptors (133 °C) than MYT (Tg = 80 °C) and DYTCVT (Tg = 120 °C), D18:DYTVT:DYTCVT OSCs have significantly higher photostability (t80% lifetime = 4250 h under 1‐sun illumination) compared to D18:MYT (t80% lifetime = 40 h) and D18:DYTCVT OSCs (t80% lifetime = 2910 h).

Spectrally Resolved Exciton Polarizability for Understanding Charge Generation in Organic Bulk Hetero-Junction Diodes.

Despite decades of research, the dominant charge generation mechanism in organic bulk heterojunction (BHJ) devices is not completely understood. While the local dielectric environments of the photoexcited molecules are important for exciton dissociation, conventional characterizations cannot separately measure the polarizability of electron-donor and electron-acceptor, respectively, in their blends, making it difficult to decipher the spectrally different charge generation efficiencies in organic BHJ devices. Here, by spectrally resolved electroabsorption spectroscopy, we report extraction of the excited state polarizability for individual donors and acceptors in a series of organic blend films. Regardless of the donor and acceptor, we discovered that larger exciton polarizability is linked to larger π-π coherence length and faster charge transfer across the heterojunction, which fundamentally explains the origin of the higher charge generation efficiency near 100% in the BHJ photodiodes. We also show that the molecular packing of the donor and acceptor influence each other, resulting in a synergetic enhancement in the exciton polarizability.

A Difluoro-Methoxylated Ending-Group Asymmetric Small Molecule Acceptor Lead Efficient Binary Organic Photovoltaic Blend.

Developing a new end group for synthesizing asymmetric small molecule acceptors (SMAs) is crucial for achieving high-performance organic photovoltaics (OPVs). Herein, an asymmetric small molecule acceptor, BTP-BO-4FO, featuring a new difluoro-methoxylated end-group is reported. Compared to its symmetric counterpart L8-BO, BTP-BO-4FO exhibits an upshifted energy level, larger dipole moment, and more sequential crystallinity. By adopting two representative and widely available solvent additives (1-chloronaphthalene (CN) and 1,8-diiodooctane (DIO)), the device based on PM6:BTP-BO-4FO (CN) photovoltaic blend demonstrates a power conversion efficiency (PCE) of 18.62% with an excellent open-circuit voltage (VOC) of 0.933V, which surpasses the optimal result of L8-BO. The PCE of 18.62% realizes the best efficiencies for binary OPVs based on SMAs with asymmetric end groups. A series of investigations reveal that optimized PM6:BTP-BO-4FO film demonstrates similar molecular packing motif and fibrillar phase distribution as PM6:L8-BO (DIO) does, resulting in comparable recombination dynamics, thus, similar fill factor. Besides, it is found PM6:BTP-BO-4FO possesses more efficient charge generation, which yields better VOC-JSC balance. This study provides a new ending group that enables a cutting-edge efficiency in asymmetric SMA-based OPVs, enriching the material library and shed light on further design ideas.

Positional isomerism engineering toward minimizing exciton binding energy in sulfone copolymers for enhanced uranyl photoreduction

Conjugated microporous polymers (CMPs) have emerged as promising platforms for photocatalytic separation and enrichment of radionuclides. However, the development of CMPs with efficient exciton dissociation and free charge generation is still highly hindered by their high exciton binding energy (Eb). Herein, for the first time, three sulfone-containing CMPs are fabricated to regulate Eb by position isomerism of altering linkage sites. Temperature-dependent photoluminescence spectra reveals that ECUT-3,7-SO with 3,7-site linkage achieves a diminished Eb of 40.1 meV. DFT calculation complementally demonstrate that the Eb is related to its strongly polarized electric field and large conjugation degree, which can be easily regulated via position isomerism of its building blocks. Among the three, ECUT-3,7-SO exhibits a completely conjugated structure and a large molecular dipole moment, thus significantly reducing the Eb. As a result, ECUT-3,7-SO exhibits the highest photoreduction uranium rate constant (k, T = 298.15 K) of 0.081 min−1, and the maximum uranium extraction capacity of 918.0 mg g−1 under visible-light irradiation. This work highlights the importance of positional isomerization to the development of low exciton binding energy photocatalyst for uranium resource field.

High-Performance Tandem Quantum-Dot Light-Emitting Diodes Based on Bulk-Heterojunction-Like Charge-Generation Layers.

In this study, the fundamental but previously overlooked factors of charge generation efficiency and light extraction efficiency (LEE) are explored and collaboratively optimized in tandem quantum-dot light-emitting diodes (QLEDs). By spontaneously forming a microstructured interface, a bulk-heterojunction-like charge-generation layer composed of a poly(3,4-ethylenedioxythiophene):poly(styrene sulfonate)/ZnO bilayer is fabricated and an ideal charge-generation efficiency surpassing 115% is obtained. The coupling strength of the waveguide mode for the top unit and the plasmon polariton loss for the bottom unit are highly suppressed using precise thickness control, which increases the LEE of the tandem devices. The red tandem QLED achieves an exceptionally low turn-on voltage for electroluminescence at 4.0V and outstanding peak external quantum efficiency of 42.9%. The ultralow turn-on voltage originates from the sequential electroluminescence turn-on of the two emissive units of the tandem QLED. Benefiting from its unique electroluminescent features, an easily fabricated optical-electrical dual anti-counterfeiting display is built by combining a dichromatic tandem QLED with masking technology.