Effect Of Thermal Cycling Research Articles

Effects of Welding Parameters on Sigma Phase Precipitation in 25Cr-5Ni-1Mo-2.5Cu-1Mn-0.18N Duplex Stainless Steel

Recently, a new grade of duplex stainless steel, UNS S82551 (25Cr-5Ni-1Mo-2.5Cu-0.18N), has been developed to overcome the drawbacks in super martensitic stainless steel, conventional 22Cr and 25Cr super duplex stainless steels in terms of productivity and cost. The characteristic of the alloy design of UNS S82551 is to use Cu, instead of Mo, to ensure comparable corrosion resistance and strength. In addition, due to the significant decrease in Mo content, UNS S82551 is expected to be less sensitive to sigma phase precipitation during single or multi-pass welding compared with conventional and super duplex stainless steels. There is a trade-off between achieving better properties and avoiding sigma phase precipitation when increasing alloying elements such as Mo, Cr and Cu. In order to utilize the new UNS S82551 steel in industry for welding in a similar manner to conventional and super duplex stainless steels, the prevention of sigma phase precipitation is important. This work investigated the effect of weld thermal cycling on sigma phase precipitation behaviour in UNS S82551 welds. During thermal cycling in the tests, the amount of sigma phase for UNS S31803 and UNS S32750 increased with increasing the number of thermal cycles, and lower cooling rate, but it was not observed for UNS S82551. Based on the isothermal kinetics of sigma phase precipitation, the amount of sigma phase precipitated during thermal cycle can be predicted by applying the additivity rule to the physical model. The area fractions of sigma phase calculated have a good fit to the experimental ones.

Effect of temperature and thermal cycles on the mechanical behavior of sandwich structure with entangled metallic wire mesh

As a novel rigid–flexible heterogeneous material, the sandwich structure with the entangled metallic wire mesh (EMWM) core has obvious advantages on thermo-mechanical performances due to its all-metallic material and structure. Of particular and complexity is the crosslinked microstructure of EMWM core, leading to ambiguous mechanical behaviors of the sandwich structure under gradient temperature and thermal cycles. In the work, the compressive and shear properties of the sandwich structure in different structure directions of the EMWM core were investigated, as well as the thermal cycling failure. The experimental result reveals that the sandwich structure has an excellent compression performance when the temperature below 750 °C. With the temperature increasing, the shear performance of the sandwich structure exhibits a trend from rise to decline. Furthermore, the shear property of the sandwich structure in the transversal direction is better than that in the longitudinal direction. And, the effect of thermal cycle on the failure behaviors (including, the deformation of face-sheet and the delamination of EMWM core) of the sandwich structure was observed. In the number of thermal cycles ranged of 50–200, there are few declinations of the compression and shear performance of the sandwich structure.

Power and thermal-aware virtual machine scheduling optimization in cloud data center

Virtual machine (VM) consolidation technology is a commonly used energy-saving method in data centers. Most of the existing methods are committed to consolidating VMs to a small number of servers to improve the utilization of server resources and reduce the total energy consumption while preventing hotspots. However, energy and thermal-aware VM scheduling is a multi-objective optimization problem. Most of the existing related work cannot provide adequate means to adjust the impact of energy consumption and temperature on VM scheduling. Hence, this paper proposes a power and thermal-aware VM dynamic scheduling scheme (PTDS) for cloud data centers. The proposed PTDS dynamically adjusts the VM consolidation scheme by real-time detecting the server temperature and resource utilization rate under the premise of considering the thermal cycle effect of the data center computer room. Power and Thermal Objective Ant Colony Optimization (PTOACO) is proposed in the VM placement. PTOACO improves the defect that the ant colony algorithm easily falls into local optimization and adds control parameters to adjust the bias between sub-objectives. We performed extensive experiments by using real PlanetLab and random workloads. The performance results were compared with several advanced schemes regarding total energy consumption, hotspots, SLA violation rate, etc. The experimental results demonstrate that PTDS reduces energy consumption by 26.69% on average compared with other advanced schemes and ensures a meager SLA violation rate while avoiding hotspots.

Mechanical Properties and Thermal Shock Behavior of Al2O3-YSZ Ceramic Layers Obtained by Atmospheric Plasma Spraying

Ceramic coatings have many advantages for industrial and medical applications due to their exceptional properties. Ceramic coatings with a thickness of approximately 45 μm, after grinding, were grown using a robotic arm that used the atmospheric plasma spraying procedure. The thermal shock stresses—a common situation in applications but difficult to reproduce under laboratory conditions—of the ceramic layers on top of the metal substrate was achieved using solar energy focused by a concentrating mirror, based on experiments conducted in the CNRS-PROMES laboratory, UPR 8521, belonging to the French National Centre for Scientific Research (CNRS). The ceramic layers showed excellent stability at 1000 °C, even at high heating or cooling rates. At high temperatures (above 1800 °C), the exfoliation of the complex ceramic layer was observed. No differences in the structural, phase, mechanical or adhesion properties of the ceramic layer were observed after the thermal shock cycles (in the literature, there have been quite few reports regarding the properties of the ceramic layers after the thermal shock application). Scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS), atomic force microscopy (AFM) and X-ray diffraction (XRD) techniques were used to characterize the complex ceramic coating and the effects of thermal shock cycling. The phases and chemical composition of the complex coatings remained similar, insensitive to thermal shock at 1000 °C, consisting of a mixture of crystalline yttrium zirconium oxide and α and γ alumina. For all cases, the main residual stress state was tensile. After 5 or 10 cycles of thermal shocks, a smoothing of the residual stress state was observed in the investigated area. A higher temperature (above 1800 °C), applied as thermal shock, led to higher residual stresses and resulted in large cracks and the spallation of the coating layer.

Understanding thermal and redox cycling behaviors of flat-tube solid oxide fuel cells

The performance stability of solid oxide fuel cells (SOFCs) under thermal and redox cycles is vital for large-scale applications. In this work, we investigated the effects of thermal and redox cycles on cell performances of flat-tube Ni/yttria-stabilized zirconia (Ni/YSZ) anode-supported SOFCs. Cell performance was considerably affected by the duration of oxidation during redox cycles and the heating rate during the thermal cycles. The cell tolerated 20 short-term redox cycles (5 min oxidation) without significant performance degradation. Besides, the cell exhibited superior stability during 8 thermal cycles with a slow heating rate (4 °C min−1) to that with a fast heating rate (8 °C min−1). These results reflected that the thick anode support (2.7 mm) offered strong resistance to the shocks caused by redox and thermal cycling. Moreover, the morphological changes of the Ni phase during the redox and thermal cycling were investigated using Ni-film anode cells. Agglomeration of Ni particles and dissociation between the Ni film and the YSZ substrate were confirmed after 5 redox cycles, whereas no significant changes in Ni film emerged after 8 thermal cycles.

Effect of multiple thermal cycling on the microstructure and microhardness of Inconel 625 by high-speed laser cladding

Establishing the relationship between thermal cycling and the induced evolution of microstructures and cladding layer properties is crucial to achieving microstructural and performance control, given the complexity involved in high-speed laser cladding process. We hereby report our new findings from laser cladding of Inconel 625 on Q245R steel substrate using a high-speed laser cladding technique. The microstructure evolution and microhardness variations in the first cladding track with different thermal cycles were examined by XRD, SEM, EBSD, TEM, and microhardness tests in detail. Numerical simulation was also conducted to characteristically illustrate the complex thermal cycles during the laser cladding process. Our work revealed that the first six thermal cycles resulted in significant variations of microstructure in the laser cladding layers. The dislocation density and low angle grain boundaries (LAGBs) of the first cladding track decreased after two thermal cycles due to the high peak temperature (above 1000 °C) of thermal cycles and subsequently increased when subjected to further thermal cycles with low peak temperature (below 500 °C). The microhardness value increased from 220 HV0.2 to 320 HV0.2, mainly caused by the formation of precipitated phase during the first four thermal cycles, and through by the enhancement of dislocations after six thermal cycles.

The effect of multiple thermal cycles on Ti-6Al-4V deposits fabricated by wire-arc directed energy deposition: Microstructure evolution, mechanical properties, and corrosion resistance

Thermal cycles have an important effect on the microstructure and properties of the components fabricated by wire-arc directed energy deposition (wire-arc DED). In this study, a Gleeble thermal-mechanical simulator was adopted to create closer-to-reality thermal cycles with the assistance of a numerical simulation model and experimental Ti-6Al-4V deposition. Step-by-step microstructure evolution, including αm, retained β, and GB α, microhardness gradual variation, and the corrosion resistance change before and after the entire thermal cycle were investigated. Therefore, combining phase orientation and high-magnification morphology, transformed and untransformed α that occurred in low- and medium-temperature thermal cycles can be distinguished. After the entire thermal cycle, αm laths coarsened from ∼1 µm to ∼1.2 µm, and the content of retained β phase became more and more. The αm formed around grain boundaries partially disappeared and was occupied by α laths from the inner grain. GB α was more continuously distributed along prior β grain boundaries due to its lower formation temperature during the subsequent thermal cycles that were occurring incomplete α→β transformation. The severe preferential orientation of α phases formed after the deposition and high-temperature thermal cycle was also alleviated through the twice low-temperature thermal cycles. Besides, the microhardness decreased from 318.78 ± 7.5 HV to 285.17 ± 5.3 HV after the high-temperature thermal cycle but eventually increased significantly to 330.5 ± 6.4 HV after experiencing the final low-temperature thermal cycle. The corrosion resistance decreased after the entire thermal cycle, indicating a performance difference between the top and bottom regions of the Ti-6Al-4 V component fabricated by wire-arc DED.

Shear creep behaviour of soil–structure interfaces under thermal cyclic loading

The coupling effect of initial shear stress and thermal cycles on the thermomechanical behaviour of clay concrete and sand–concrete interfaces has been studied. A set of drained monotonic direct shear tests was conducted at the soil–concrete interface level. Samples were initially sheared to half of the material's shear strength and then they were subjected to five heating/cooling cycles before being sheared to failure. The test results showed that the effect of thermal cycles on the shear strength of the materials was negligible, yet shear displacement occurred during application of thermal cycles without an increase in shear stress, confirming the coupling between the shear stress and temperature. In addition, a slight increase of stiffness due to the coupling was observed which diminished with further shearing.

Thermal cycling effects on the seismic wave propagation coefficients of granite

The seismic wave propagation properties of granite after thermal cycles were experimentally investigated. The granite specimens were subjected to a series of thermal cycles with different thermal cycling temperatures and numbers. Ultrasonic and pendulum impact tests were performed on the granite after thermal cycles. Subsequently, a theoretical study was introduced to explore the wave propagation coefficients of granite after thermal cycles. The effects of the thermal cycling number on the wave attenuation rate, wave velocity, attenuation coefficient, and wavenumber were discussed. The results indicate that the wave velocity and dynamic elastic modulus decrease as the number of thermal cycles increases and that the damage factor increases as the number of thermal cycles increases. However, the variations in wave velocity, dynamic elastic modulus, and damage factor are concentrated mainly in the first thermal cycle. The results further indicate that the wave propagation coefficients, attenuation coefficient, and wavenumber increase as the number of thermal cycles increases. However, they are not significantly influenced by the amplitude and wavelength of impact loading.

Effect of the Welding Thermal Cycle on the Microstructure and Mechanical Properties of TiC Cermet HAZ Using the Gleeble Simulator

The effect of heat input on the microstructure and mechanical properties of TiC cermet in MIG welding has been comprehensively investigated by Gleeble simulation. The microstructure, phase composition and shear fracture of TiC cermet were examined by OM (optical microscopy), SEM (scanning electron microscope), TEM (transmission electron microscope) and XRD (X-ray diffraction) analyses. The results show that the heat input has a significant effect on the properties of TiC cermet. With TiC particles and the austenite bonding phase remaining the same, the heat input can effectively improve the toughness of the bonding phase and the structural strength from 219.9 HV0.01 to 380.5 HV0.01 and from 469 MPa to 684 MPa, respectively, as the dislocation density increases while the heat input increases. When the heat input is 3.4 KJ/cm, the shear strength reaches the peak at 684 MPa, with the increase in heat input, the secondary fragmentation of TiC particles increases, and the crack propagation leads to a significant decrease in material strength.

Effect of Thermal Cycling on Microstructure and Mechanical Properties of Cf/SiC–Al Composites

Thermal cycling inevitably affects the microstructure and mechanical properties of composites due to the differences in thermal expansion coefficients (CTEs) of each component. Herein, the evolution of the microstructure and in‐plane compressive properties of Cf/SiC–Al composites after different thermal cycles at different temperature differences are investigated. Moreover, the magnitude and state of residual thermal stress in each component of the composites after thermal cycling are further analyzed by X‐ray diffraction and nanoindentation methods. The results show that with the increase of the temperature difference and the number of thermal cycles, the residual stress in each component gradually accumulates, accompanied by interface debonding and microcracks in the fiber/matrix interface area, which can release part of the residual stress. The evolution of the residual stress and the interface microstructure has a significant effect on the in‐plane compressive strength of the composites. The release of residual stress and the generation of some microcracks are beneficial to the compressive strength, but too many microcracks can reduce the strength.

Microstructure evolution and mechanical properties in a gas tungsten arc welded Fe42Mn28Co10Cr15Si5 metastable high entropy alloy

Weldability studies on high entropy alloys are still relatively scarce, delaying the deployment of these materials into real-life applications. Thus, there is an urgent need for in-depth studies of the weldability of these novel advanced engineering alloys. In the current work, an as-cast Fe42Mn28Co10Cr15Si5 metastable high entropy alloy was welded for the first time using gas tungsten arc welding. The weld thermal cycle effect on the microstructure evolution over the welded joint was examined using electron microscopy in combination with electron backscatter diffraction, synchrotron X-ray diffraction analysis, and thermodynamic calculations. Furthermore, tensile testing and hardness mapping were correlated with the microstructure evolution. The microstructure evolution across the joint is unveiled, including the origin of the ε-h.c.p. phase at different locations of the material. Different strengthening effects measured throughout the joint are associated with the weld thermal cycle and resulting microstructure. A synergistic effect of smaller grain size of the ε-h.c.p. phase in the fusion zone, overturns the reduced volume fraction of this phase, increasing the local strength of the material. Moreover, the brittle nanosized σ phase was also found to play a critical role in the joints’ premature failure during mechanical testing.

Effect of thermal cycles on the engineering properties and durability of sustainable fibrous high-strength concrete

In this research, the effect of heat–cool cycles (HCCs) on high-strength concrete (HSC) containing steel fibres (SFs), polypropylene fibres (PPFs), and date palm fibres (DPFs), which were named fibrous high-strength concrete (FHSC), was studied. To produce FHSC, three doses of 0.2, 0.6, and 1 percent of each fibre were used. All samples were tested after 28 days of normal water curing and 270 days of exposure to HCCs (continuing the authors’ project and research published at 28 and 180 days). This entails heating for 2 days at 60 C in the oven and cooling for another 2 days at room temperature for 270 days. The experiment’s findings revealed that fibre reinforcement in concrete enhances its strength and durability. By incorporating the three types of fibres into high-strength concrete, with and without HCCs, the modulus of rupture was significantly increased. In both conditions, including with or without the implementation of HCCs, incorporating the three fibre types into the HSC showed a significant increase in toughness. As a result, natural date palm fibres can produce sustainable FHSC that can withstand harsh environmental conditions. Moreover, compared to the previous study conducted by the authors at 180 days, there is a slight severity in both the pattern of decrease and increase of the studied characteristics at 270 days caused by the effect of thermal cycles and fibres.

Ni Porous Preforms Compacted with Al2O3 Particles and Al Binding Agent.

This work presents an energy-efficient, cheap, and rapid production method of a metal-ceramic preform with open porosity suitable for liquid metal infiltration and filtration applications. It is based on cold isostatic pressing of a mixture of relatively hard Ni and Al2O3 powders with the addition of small amount of Al powders, acting as a binding agent. Open porosity is primarily controlled by Al2O3 particles partially separating Ni particles from mutual contacts. Cold isostatic pressed green compacts were subjected to thermal oxidation by heating in air to 600 °C, 700 °C, and 800 °C. The weight gain and open porosity of oxidized compacts were examined. The chemical composition and microstructure were analyzed by SEM-EDS and XRD techniques. The stability of preforms and the effect of thermal cycling on the open porosity were tested by thermal cycling in an inert Ar atmosphere in the temperature range up to 800 °C. It appeared that, in addition to NiO being an expected product of oxidation, Ni aluminides and spinel particles also played an important role in inter-particle bonding formation. Ni-NiO porous composites resist chemical corrosion and exhibit structural and chemical stability at higher temperatures and admixed Al2O3 particles do not deteriorate them. After subsequent infiltration with Al, it can offer a lower density than other materials, which could result in lower energy consumption, which is highly needed in industries such as the automotive industry.

Effect of Thermal Cycling on Grain Evolution and Micro-Segregation in Selective Laser Melting of FGH96 Superalloy

Extremely rapid heating and cooling rates during the additive manufacturing (AM) process generate complicated thermal cycles, which affect the microstructure evolution and ultimate mechanical properties of the alloy. In this paper, FGH96 blocks with a height of 6 mm were prepared by selective laser melting (SLM) and the microstructure was characterized by scanning electron microscopy (SEM) and transmission electron microscopy (TEM). Comparing specimens of varying heights, it was found that subsequent thermal cycles (STC) coarsened some solidified grains and accelerated the grain growth along the build direction, together with an increase in texture intensity and high-angle grain boundaries (HAGBs). After coarsening the grains in the middle portion of the built block, finer grains were observed near the top area due to a faster cooling rate. There were numerous dislocations in the grain because of the occurrence of unequal internal tension. In the middle of the sample with stable thermal cycles, the dislocations were both perpendicular to the grain growth direction and 45° off it. In spite of the texture characteristics, the segregation of elements was also found to be influenced by thermal cycling. Inherent reheating leads to the increase in the Laves phase and the decrease in the γ’ phase as subsequent deposition. This was also one of the reasons why the microhardness of the sample decreased as the building height and the other reason being the decrease in the solution treatment of the later sediments.

The effect of elevated temperature on self-compacting concrete: Physical and mechanical properties

Concrete’s thermal properties are more complex than for most materials because not only is the concrete a composite material whose constituents have different properties, but its properties also depend on moisture and porosity. Exposure of concrete to elevated temperature affects its mechanical and physical properties. In the current study, M40 and M80 grades of plain self-compacting concrete (SCC) mixes are developed using Nan Su mix design principles to investigate the effect of elevated temperatures on 1) weight and compressive strength 2) compressive strength of SCC when tested cool and hot 3) effect of 2, 4 and 6 hrs. exposure duration of elevated temperatures on compressive strength 4) modulus of elasticity 5) size of testing specimen and 5) effect of thermal cycles on SCC mixes. Results derived the following conclusions 1) the M80 specimens lose more strength than M40 SCC specimens when subjected to elevated temperatures ;2) specimens heated and then permitted to cool before testing lose more strength than those tested while hot; 3) the longer the duration of heating before testing, the larger the loss in strength; 4) The decrease in modulus of elasticity caused by elevated-temperature exposure is more pronounced than the decrease in compressive strength. 5) Small test specimens generally incur greater strength losses than larger ones and 6) Specimens subjected to several cycles of heating and cooling lose more strength than those not subjected to thermal cycling.

Effects of thermal cycles on soil behaviour: theoretical and experimental studies

Fundamental understanding and proper modelling of soil behaviour under thermal cycles are increasingly important and essential for the analysis and design of many emerging infrastructures, such as geothermal structures and embankment-atmosphere interactions under a changing climate. Previous studies mainly focus on monotonic thermal loading of thermo-mechanical behaviour of soils. Based on a unified, state-dependent theoretical framework in the form of compliance matrix, a new constitutive model is developed to simulate the cyclic thermo-mechanical behaviour of saturated and unsaturated soils. This new bounding surface model is formulated in terms of Bishop’s stress and suction. Apart from the loading and bounding surfaces, a memory surface is incorporated in the model to simulate cyclic thermal behaviour of soils. To verify the new model, computed results are compared with measured data from cyclic heating-cooling tests on saturated and unsaturated soils at various suctions. Based on this new model, two engineering applications are analysed including cyclic thermally loaded floating energy pile foundations and a deep excavation in the unsaturated ground. Consistent results are obtained between computed and measured data.

Experimental investigation of the effect of thermal cycling on the thermomechanical properties of three rock varieties for high temperature thermal energy storage

During the past years “rock batteries” have become increasingly relevant for the storage of renewable energy sources, such as wind and solar energy, because of their economic and ecological advantages with respect to previously more common materials for thermal energy storage (TES) such as salt. In rock-based TES systems, thermal energy is stored in packed-bed rock using air as heat transfer fluid. We investigated three different rock types with respect to changes in thermomechanical properties after different numbers of thermal cycles, Ruhr sandstone (Oberste quarry in Dortmund - Germany), basalt (commercial MTV basalt) and Calanca gneiss. Cylindrical samples were heated to 800°C within 11,5 h before temperature was kept constant for another 30 min and then decreased within 11,5 h. Samples were thermomechanically investigated before thermal treatment, and again after 1, 3, 7 and 15 cycles. Additionally, two samples of each rock type were subjected to a thermal cycle with a maximum temperature of 450°C and to 1000°C, respectively, at a heating/cooling rate corresponding to that of the samples heated to 800°C. Samples were characterised with respect to ultrasound wave velocity, bulk density, thermal conductivity, thermal diffusivity, uniaxial compressive strength, splitting tensile strength, mineral content (X-ray powder diffraction) and microstructure (thin section analysis). Samples of basalt could not withstand the standard heating rate. The samples crushed into small pieces also when heating rates were reduced and at a maximum heating temperature of 800°C. For sandstone and gneiss, the ultrasound wave velocity, bulk density, thermal conductivity, thermal diffusivity, uniaxial compressive strength and splitting tensile strength decreased systematically with increasing number of cycles, while the maximum reduction occurred after the first cycle and the relative reduction was similar between both rocks. Microstructural analysis indicated an increase in crack density and minor mineralogical changes upon heating. Both rocks, Ruhr sandstone and Calanca gneiss, appear suitable for TES, but Calanca gneiss is less suitable for temperatures above 800°C due to a significant reduction in bulk density and uniaxial compressive strength when heated to 1000°C. Also, its anisotropy and anisotropic response to heating can lead to preferred flow paths of the heat transfer fluid. Ruhr sandstone maintains a high uniaxial compressive strength of about 100 MPa even after 15 cycles while thermal capacity was only slightly reduced or even increased, and can be recommended for use in high temperature TES. This study is the outcome of a research-oriented teaching program at Ruhr-University Bochum within the Geoscience curriculum for students with focus on Engineering Geology. Student authors (Fränzer to Thomas) are listed in alphabetical order.

Effects of vacuum thermal cycling, ultraviolet radiation and atomic oxygen on the mechanical properties of carbon fiber/epoxy shape memory polymer composite

The use of shape memory polymer composites as novel materials for next generation space deployable structures requires the study of the effect of space environment upon their properties. The resistance of carbon fiber/epoxy shape memory polymer composite to vacuum thermal cycling, ultraviolet radiation and atomic oxygen has been evaluated separately by using ground-based simulation facilities. The thermal cycling condition has a temperature range of −100 °C to +100 °C with cycle times of 0, 15, 30, and 45. The irradiation times of ultraviolet with a wavelength range of 250 nm–400 nm are 0, 80, 160, and 240 h. The atomic oxygen radiation has a translational energy of about 5 eV and a flux of about 2 × 1015 atoms/cm2 at the sample position, and the irradiation times are 0, 33, 66, and 100 h. The shape memory polymer composite specimens are compared in terms of morphology, tensile modulus, breaking strength and elongation at break before and after irradiation. Results show that thermal cycling increases tensile modulus but decreases the breaking strength and the elongation at break of material after 45 cycles. The effect of ultraviolet radiation on mechanical properties of materials depends on the radiation dose received. Atomic oxygen can negatively but slightly affect the mechanical properties of the material.

Microstructure and mechanical properties of GTA-based wire arc additive manufactured AZ91D magnesium alloy

Wire arc additive manufacturing offers advantages in producing large metal structures. The current research on GTA-based wire arc additive manufacturing (GTA-WAAM) of magnesium alloys is focused on deformed magnesium alloys, mainly on the Mg-Al alloy system. However, there is little research on GTA-WAAM for casting magnesium alloy. This study investigates the microstructural characteristics and mechanical properties of AZ91D magnesium alloy (AZ91D-Mg) deposited by GTA-WAAM. Single-pass multilayer thin-walled components were successfully fabricated. The results show that equiaxed grains dominate the microstructure of the deposited samples. During the remelting process, the precipitated phases dissolve into the matrix, and they precipitate and grow from the matrix under the thermal effect of the subsequent thermal cycle. The mechanical properties in the vertical and horizontal directions are similar, showing higher overall mechanical properties than the casting parts. The average yield strength is 110.5 MPa, the ultimate tensile strength is 243.6 MPa, and the elongation is 11.7%. The overall hardness distribution in the deposited sample is relatively uniform, and the average microhardness is 59.6 HV0.2.