Dual-mode System Research Articles

Comparative analysis and optimization of the annual performance for a novel internet data center cooling system

Internet data centers generate considerable heat loads and expend up to 50% of the total facility energy. This study investigate the performance of a novel internet data center cooling system that incorporates two operating modes, namely the forced cooling mode and a free cooling mode. The study optimized the secondary fluid flow rate to select the mode change temperature for the dual-mode internet data center cooling system. Performance comparison between the novel dual-mode air source internet data center cooling system and a conventional air source internet data center cooling system was studied at varying outdoor air temperature range from -4 °C to 35 °C, and using the integrated coefficient of performance rating method. The novel dual-mode system performance was slightly lower than the conventional system performance at outdoor temperatures above the mode change temperature, but the former was significantly higher than the latter at outdoor temperatures below the mode change temperature. Furthermore, the integrated coefficient of performance of the novel dual-mode internet data center cooling system represented by 41% higher value comparing with the conventional system, showing that the novel dual-mode internet data center cooling system has great prospects in significantly enhancing the annual energy savings of internet data centers.

Single-trigger dual-modal nanoplatform for in situ switch on cancer diagnosis imaging

Tumor markers in situ switch on nanoplatform is of great significance for disease early diagnosis and accurate treatment. It has significant advantages to realize simultaneous detection of multiple signals through single signal triggering. However, traditional nanoplatform often needs complex modification and integration of multiple materials. Herein, to achieve “one stone for two birds” and simplify nanoplatform structure, a dual-modal system was developed for glutathione (GSH)-triggered in situ switch on imaging of cancer. The transition metal oxide FeOOH shell was generated around CuInZnS quantum dots (CIZS QDs), and the near-infrared (NIR) fluorescence of QDs could be quenched. After being reduced to Fe2+ by GSH which normally overexpressed in cancer cells, CIZS QDs with fluorescence will generate. Therefore, the GSH-triggered fluorescence recovery could be used for in situ switch on cancer diagnostic imaging of cells and tumor-bearing mice. Furthermore, the reaction product Fe2+ enabled followed chemodynamic therapy (CDT) and magnetic resonance (MR) imaging properties to realize dual-modal diagnosis imaging. Compared with other FeOOH nanostructures, our method was more simple and efficient. Hence, this study provided a new attempt to construct versatile nanoplatform, which integrated cancer diagnosis imaging capability and may be applied in subsequent therapeutics.

A dual-mode miniature wireless system for lensless CMOS-based bioimaging devices

In this paper, a miniature wireless system for use in conjunction with original lensless CMOS-based imaging devices is developed for in vivo imaging experiments. The system mainly comprises an image sensor, a microcontroller, and a Bluetooth Low Energy module for wireless data transmission. In addition to the hardware suitable for studies imposing freely-moving conditions, image sampling and processing features are implemented. Results demonstrate readiness for imaging in vivo, with adequate data transfer speed for a 12 × 12 pixel region of interest with an area of 180 × 180 μm2.

A dual-mode system for water purification and cooling using a thermal desalination technique coupled to a heat pump unit

Humidification-dehumidification is one of the most suitable small-scale desalination methods based on air humidification and condensation. The major energy-consuming components for a humidification-dehumidification process are a heat source for the humidifier and a cooling source for the dehumidifier. To improve the performance of these processes, the fluids were preheated using different energy sources or waste heat. In recent years, preheating air or saline water using heat from a heat pump's condenser has been explored to improve the system's performance and to produce cooling and desalination simultaneously. However, separate heat exchangers and additional solar collectors/heaters were used to preheat the second fluid. In this work, the air-cooled condenser of a heat pump has been replaced by an evaporative condenser and used as a humidifier. This configuration has been scarcely explored in the literature and requires a single heat exchanger to preheat the fluids. On the other hand, the heat pump's evaporator was used to produce low-temperature coolant, circulated through a cooling coil where the humid air from the evaporative condenser is cooled and dehumidified to produce fresh water and cooling simultaneously. This modification ensures reduced space requirement and better system performance than other heat pumps coupled to humidification-dehumidification systems for simultaneous cooling and desalination. Also, the present system operates flexibly to switch between desalination and cooling mode (mode-1) to cooling mode (mode-2). Towards this, a mathematical model of the system has been developed and analyzed under various operating conditions. The system's performance, which includes desalination yield, cooling output, gained output ratio, and coefficient of performance under each mode of operation, is studied for different ambient conditions and evaporator temperatures. The maximum desalination yield, cooling output, gained output ratio, and coefficient of performance of mode-1 are 4.55 LPH, 0.82 kWth, 3.79, and 0.75, respectively. The maximum cooling output and COP of mode-2 are 3.79 kWth and 3.82, respectively. The exergy efficiencies for mode-1 and mode-2 are 32.7 % and 29.7 %, respectively.

Engineering an Enzymatic Cascade Catalytic Smartphone-Based Sensor for Onsite Visual Ratiometric Fluorescence-Colorimetric Dual-Mode Detection of Methyl Mercaptan.

Precise and reliable onsite detection of methyl mercaptan (CH3SH) is of great significance for environmental surveillance. Here, we synthesized a novel blue fluorescence nanozyme CeO2@TPE with high peroxidase-like activity by employing aggregation-induced emission (AIE) tetraphenylethene (TPE) to embed into hollow CeO2 nanospheres. In the presence of ethanol oxidase (AOX) and o-phenylenediamine (OPD), we engineered an enzymatic cascade activation ratiometric fluorescence-colorimetric dual-mode system AOX/CeO2@TPE + OPD toward CH3SH. In this design, CH3SH initiated AOX catalytic activity to convert it into H2O2 for activating the peroxidase-like activity of CeO2@TPE, producing •OH for oxidizing the naked-eye colorless OPD into deep yellow 2,3-diaminophenazine (DAP) with an absorption enhancement at ∼425 nm, companied by a new emission peak at ∼550 nm to match with the intrinsic emission at ∼441 nm for observing ratiometric fluorescence response, enabling a ratiometric fluorescence-colorimetric dual-mode analysis. Interestingly, both the ratiometric fluorescence and colorimetric signals could be gathered for being converted into the hue parameter on a smartphone-based sensor, achieving the onsite visual fluorescence-colorimetric dual-mode detection of CH3SH in real environmental media with acceptable results. This study gave a novel insight into designing target-responsive enzymatic cascade activation system-based efficient and reliable dual-mode point-of-care sensors for safeguarding environmental health.

Self-Assembled Plasmonic Nanojunctions Mediated by Host-Guest Interaction for Ultrasensitive Dual-Mode Detection of Cholesterol.

Herein, a fluorescence and surface-enhanced Raman spectroscopy dual-mode system was designed for cholesterol detection based on self-assembled plasmonic nanojunctions mediated by the competition of rhodamine 6G (R6G) and cholesterol with β-cyclodextrin modified on gold nanoparticles (HS-β-CD@Au). The fluorescence of R6G was quenched by HS-β-CD@Au due to the fluorescence resonance energy transfer effect. When cholesterol was introduced as the competitive guest, R6G in the cavities of HS-β-CD@Au was displaced to recover its fluorescence. Moreover, two of HS-β-CD@Au can be linked by one cholesterol to form a more stable 2:1 complex, and then, plasmonic nanojunctions were generated, which resulted in the increasing SERS signal of R6G. In addition, fluorescence and SERS intensity of R6G increased linearly with the increase in the cholesterol concentrations with the limits of detection of 95 and 74 nM, respectively. Furthermore, the dual-mode strategy can realize the reliable and sensitive detection of cholesterol in the serum with good accuracy, and two sets of data can mutually validate each other, which demonstrated great application prospects in the surveillance of diseases related with cholesterol.

PEC/Colorimetric Dual-Mode Lab-on-Paper Device via BiVO4/FeOOH Nanocomposite In Situ Modification on Paper Fibers for Sensitive CEA Detection.

A dual-mode lab-on-paper device based on BiVO4/FeOOH nanocomposites as an efficient generating photoelectrochemical (PEC)/colorimetric signal reporter has been successfully constructed by integration of the lab-on-paper sensing platform and PEC/colorimetric detection technologies for sensitive detection of carcinoembryonic antigen (CEA). Concretely, the BiVO4/FeOOH nanocomposites were in situ synthesized onto the paper-working electrode (PWE) through hydrothermal synthesis of the BiVO4 layer on cellulose fibers (paper-based BiVO4) which were initially modified by Au nanoparticles for improving the conductivity of three dimensional PWE, and then the photo-electrodeposition of FeOOH onto the paper-based BiVO4 to construct the paper-based BiVO4/FeOOH for the portable dual-mode lab-on-paper device. The obtained nanocomposites with an FeOOH needle-like structure deposited on the BiVO4 layer exhibits enhanced PEC response activity due to its effective separation of the electron-hole pair which could further accelerate the PEC conversion efficiency during the sensing process. With the introduction of CEA targets onto the surface of nanocomposite-modified PWE assisted by the interaction with the CEA antibody from a specific recognition property, a signal-off PEC signal state with a remarkable photocurrent response decreasing trend can be achieved, realizing the quantitative detection of CEA with the PEC signal readout mode. By means of a smart origami paper folding, the colorimetric signal readout is achieved by catalyzing 3,3',5,5'-tetramethylbenzidine (TMB) to generate blue oxidized TMB in the presence of H2O2 due to the satisfied enzyme-like catalytic activity of the needle-like structure, FeOOH, thereby achieving the dual-mode signal readout system for the proposed lab-on-paper device. Under the optimal conditions, the PEC and colorimetric signals measurement were effectively carried out, and the corresponding linear ranges were 0.001-200 ng·mL-1 and 0.5-100 ng·mL-1 separately, with the limit of detection of 0.0008 and 0.013 ng·mL-1 for each dual-mode. The prepared lab-on-paper device also presented a successful application in serum samples for the detection of CEA, providing a potential pathway for the sensitive detection of target biomarkers in clinical application.

Wide-field three-dimensional photoacoustic/ultrasound scanner using a two-dimensional matrix transducer array.

Two-dimensional matrix transducer arrays are the most appropriate imaging probes for acquiring dual-modal 3D photoacoustic (PA)/ultrasound (US) images. However, they have small footprints which limit the field-of-view (FOV) to less than 10 mm × 10 mm and degrade the spatial resolution. In this study, we demonstrate a dual-modal PA and US imaging system (using a 2D matrix transducer array and a motorized 2D scanning system) to enlarge the FOV of volumetric images. Multiple PA volumes were merged to form a wide-field image of approximately 45 mm × 45 mm. In vivo imaging was demonstrated using rat sentinel lymph nodes (SLNs) and bladders stained with methylene blue. We believe that this volumetric PA/US imaging technique with a 2D matrix transducer array can be a useful tool for narrow-field real-time monitoring and wide-field imaging of various preclinical and clinical studies.

A dual-mode "signal-on" split-type aptasensor for bisphenol A via target-induced hybridization chain reaction amplification.

Herein, a dual-mode detection system was constructed for efficient and accurate detection of bisphenol A (BPA) with the assistance of the BPA-induced hybridization chain reaction (HCR). The captured DNA (cDNA) was first modified on the surface of magnetic spheres modified with gold nanoparticles and polydopamine and then hybridized with the BPA aptamer to form double-stranded DNA (dsDNA). In the presence of the BPA target, the BPA aptamer was released from the surface of the magnetic sphere. The free cDNA triggered a HCR to construct a DNA duplex. Methylene blue (MB), as a bifunctional probe, was intercalated into the double-stranded DNA to amplify the photocurrent (IPEC) of the CdS-modified electrode and generate an electrochemical current (IEC) at the same time. Under the optimized conditions, the PEC and EC signal responses of the system were linear to the logarithm of BPA concentration in the range of 1.0 × 10-10 M to 1.0 × 10-5 M. The detection limits were found to be 1.27 × 10-11 M and 3.0 × 10-11 M using the PEC and EC methods, respectively. The constructed dual-mode biosensor exhibited good performance for real sample analysis, demonstrating its promising potential for practical applications. In addition, this dual-mode detection strategy provides more accurate and reliable detection results.

A dual-mode system based on molybdophosphoric heteropoly acid and fluorescent microspheres for the reliable and ultrasensitive detection of alkaline phosphatase.

A novel colorimetric and fluorescent dual-mode sensing system based on molybdophosphoric heteropoly acid (PMA) and fluorescent microspheres (FMs) was established for monitoring the activity of alkaline phosphatase (ALP). In the presence of ALP, L-ascorbic acid-2-phosphate (AAP) could be hydrolyzed catalytically to ascorbic acid (AA), which could reduce PMA to phosphorus molybdenum blue (PMB), accompanied by the generation of colorimetric signals depending on the level of ALP. Meanwhile, the fluorescence of FMs was quenched markedly by the PMB produced due to the inner-filter effect, which constituted the response mechanism for the dual-mode sensing systems of ALP. On this basis, a PMA-FMs based dual-mode sensing system was used for the detection of ALP, which not only possessed remarkable sensitivity, with a limit of detection of 0.27 U L-1 and 0.11 U L-1, but also exhibited good analytical performance in biological samples with satisfactory results. Moreover, a simple and portable test kit for the visual detection of ALP in real serum samples was fabricated utilizing a smartphone with image-recognition and data-processing capabilities as a visual-detection platform.

UV–vis spectrophotometer and smartphone RGB dual mode detection of inorganic arsenic based on hydride generation iodine–starch system

A dual-mode analytical system based on hydride generation iodine–starch was established for the inorganic arsenic detection by UV–vis spectrophotometer and smartphone RGB. Hydride generation (HG) was used as a gaseous sample introduction technique for this dual-mode analytical system, the generated AsH3 was transported into iodine–starch solution, so that the color of iodine–starch solution was faded from dark blue to colorless, which could be recorded by UV–vis spectrophotometer and smartphone RGB simultaneously. Various experimental conditions were investigated, three certified reference water samples, three water samples and its spiked samples were detected by this dual mode analytical system under the optimized conditions, recoveries ranging 94–108 % were obtained, indicating a good accuracy and applicability of this method. A detectable concentration as low as 0.01 μg mL−1 was achieved, meeting the analysis requirement of As(III) in water samples. It is a potential analytical system for inorganic arsenic detection in field analysis.

Experimental characterization of the electrospray propulsive performance for ionic liquid propellants [EMIm][DCA] and [BMIm][DCA]

A chemical-electrospray dual-mode propulsion system is significant in improving mission capability and flexibility of a spacecraft. Hypergolic ionic liquids are potential propellants of chemical and electrospray propulsion systems. In this work, the electrical propulsive performance of two hypergolic ionic liquids 1-ethyl-3-methylimidazolium dicyanamide ([EMIm][DCA]) and 1-butyl-3-methylimidazolium dicyanamide ([BMIm][DCA]) are experimentally characterized using two array-emitter electrospray thrusters. Compared with a commonly used ionic liquid propellant 1-ethyl-3-methylimidazolium tetrafluoroborate ([EMIm][BF4]), the current magnitude and current steadiness of the electrospray thruster with [EMIm][DCA] and [BMIm][DCA] are efficiently improved, especially with [EMIm][DCA] as propellant. The results show that the low viscosity is beneficial for steady and sufficient flow supply and thus favors a long-time steady operation of the thruster. For the propellant [EMIm][DCA], the maximum specific impulse is 1791 s, i.e., 27.8% higher than that of [EMIm][BF4], while the maximum thrust 32.5 μN is 128.9% greater than that of [EMIm][BF4]. For the propellant [BMIm][DCA], the thrust-to-power ratio of the thruster is approximately 82.8% higher than that of [EMIm][BF4] at a similar specific impulse of about 1120 s resulting from a much greater thruster efficiency. These results demonstrate that [EMIm][DCA] has a better performance than [EMIm][BF4] in both maximum thrust and specific impulse, and [BMIm][DCA] performs best in the aspect of thrust-to-power ratios. This work highlights the prospect of hypergolic ionic liquids and is valuable to promote their application in chemical and electrical propulsion communities.

Harnessing the structural attributes of NiMg-CUK-1 MOF for the dual-function capture and transformation of carbon dioxide into methane

Carbon capture and conversion into chemical fuels are often considered distinct processes, whereby a sorbent is responsible for enriching a CO2 stream while a catalyst facilitates transformation into value-added commodities. Herein, we implement NiMg-CUK-1, a metal–organic framework (MOF) possessing the characteristics of both adsorbent and catalyst for the sequential capture and conversion of CO2 to methane (CH4). By harnessing the disparity in thermal stability between Ni- and Mg-CUK-1 analogues, Ni nanoparticles are preferentially generated throughout the preserved Mg portion of the framework. Tuning the Ni:Mg ratio and the NiMg-CUK-1 treatment temperature maximizes catalytic performance while preserving a substantial portion of the CO2 capture functionality inherent to the MOF. The optimized NiMg-CUK-1 is deployed in a dual-mode reactor system that alternates between ambient temperature CO2 capture and methanation under mild reaction conditions (250 °C). After five cycles, the optimal NiMg-CUK-1 reaches a levelled-out performance of 1.46 ± 0.24 mmol CO2 captured g−1, and 1.52 ± 0.23 mmol CH4 produced g−1, surpassing similar sorbent-based catalysts reliant on the chemical looping of metal oxides and carbonates. The introduced approach paves the way for combined capture and conversion of CO2 using a single dual-functional material capable of both low-temperature CO2 desorption and CH4 production.

Unsupervised and quantitative intestinal ischemia detection using conditional adversarial network in multimodal optical imaging.

Intraoperative evaluation of bowel perfusion is currently dependent upon subjective assessment. Thus, quantitative and objective methods of bowel viability in intestinal anastomosis are scarce. To address this clinical need, a conditional adversarial network is used to analyze the data from laser speckle contrast imaging (LSCI) paired with a visible-light camera to identify abnormal tissue perfusion regions. Our vision platform was based on a dual-modality bench-top imaging system with red-green-blue (RGB) and dye-free LSCI channels. Swine model studies were conducted to collect data on bowel mesenteric vascular structures with normal/abnormal microvascular perfusion to construct the control or experimental group. Subsequently, a deep-learning model based on a conditional generative adversarial network (cGAN) was utilized to perform dual-modality image alignment and learn the distribution of normal datasets for training. Thereafter, abnormal datasets were fed into the predictive model for testing. Ischemic bowel regions could be detected by monitoring the erroneous reconstruction from the latent space. The main advantage is that it is unsupervised and does not require subjective manual annotations. Compared with the conventional qualitative LSCI technique, it provides well-defined segmentation results for different levels of ischemia. We demonstrated that our model could accurately segment the ischemic intestine images, with a Dice coefficient and accuracy of 90.77% and 93.06%, respectively, in 2560 RGB/LSCI image pairs. The ground truth was labeled by multiple and independent estimations, combining the surgeons' annotations with fastest gradient descent in suspicious areas of vascular images. The total processing time was 0.05s for an image size of . The proposed cGAN can provide pixel-wise and dye-free quantitative analysis of intestinal perfusion, which is an ideal supplement to the traditional LSCI technique. It has potential to help surgeons increase the accuracy of intraoperative diagnosis and improve clinical outcomes of mesenteric ischemia and other gastrointestinal surgeries.

Dual-modality hyperspectral microscopy for transmission and fluorescence imaging

Conventional color imaging provides information in the red, green, and blue (RGB) channels with limited resolution in the spectral domain. This could lead to poor sensitivity in imaging biological samples. In fluorescence imaging, the use of multiple fluorophores is often necessary to label proteins and DNAs for in vivo experiments. Crosstalk between fluorophores can be troublesome because it is challenging to differentiate each fluorophore when their emission spectra are overlapped. To help address these issues, we developed a dual-modality hyperspectral microscopy system that combines hyperspectral imaging and microscopy imaging to provide spatial and spectral information of the samples. The dual-modality feature allows us to study biological samples and fluorescent samples using the same system. We show that applications of the system enable: the identification of different tissue and cell structures; identification of each quantum dot fluorophore, calculation of their relative proportions at each location, and elucidation of their spatial distributions in a mixture sample containing multiple types of quantum dot fluorophores. The results give a brief showcase of how hyperspectral imaging can be useful for biomedical imaging and fluorescence imaging applications.

Vitality-Enhanced Dual-Modal Tracking System Reveals the Dynamic Fate of Mesenchymal Stem Cells for Stroke Therapy.

Mesenchymal stem cell (MSC) therapy via intravenous transplantation exhibits great potential for brain tissue regeneration, but still faces thorny clinical translation challenges as the unknown dynamic fate leads to the contentious therapeutic mechanism and the poor MSC viability in harsh lesions limits therapeutic efficiency. Here, a vitality-enhanced dual-modal tracking system is designed to improve engraftment efficiency and is utilized to noninvasively explore the fate of intravenous transplanted human umbilical cord-derived MSCs during long-term treatment of ischemic stroke. Such a system is obtained by bioorthogonally conjugating magnetic resonance imaging (MRI) contrast and near-infrared fluorescence (NIRF) imaging nanoparticles to metabolic glycoengineered MSCs with a lipoic acid-containing extracellular antioxidative protective layer. The dynamic fates of MSCs in multi-dimensional space-time evolution are digitally detailed for up to 28 days using MRI and NIRF imaging equipment, and the protective layer greatly shields MSCs from reactive oxygen spices (ROS) degradation, enhances MSC survival, and engraftment efficiency. Additionally, it is observed that the bioengineered MSCs exhibit dynamic intelligent responses corresponding to microenvironment remodeling and exert enhanced therapeutic effects. This dual-modal tracking system enables long-term tracking of MSCs while improving their viability at the lesion sites, which may serve as a valuable tool for expediting the clinical translation of MSC therapy.

A smartphone-assisted down/up-conversion dual-mode ratiometric fluorescence sensor for visual detection of mercury ions and l-penicillamine

Establishment of a rapid, sensitive, visual, accurate and low-cost fluorescence detection system to detect multiple targets was of great significance in food safety evaluation, ecological environment monitoring and human health monitoring. In this work, a smartphone-assisted down/up-conversion dual-mode ratiometric fluorescence sensor was proposed based on metal-organic framework (NH2-MIL-101(Fe)) and CdTe quantum dots (CdTe QDs) for visual detection of mercury ions (Hg2+) and L-penicillamine (L-PA), in which NH2-MIL-101(Fe) was used as the reference signal and CdTe QDs was used as the response signal. The down-conversion fluorescence system at excitation wavelength of 300 nm (ex: 330 nm) was used to detect Hg2+ and L-PA, in which the detection limit of Hg2+ was 0.053 nM with the fluorescence color changed from green to blue, and the detection limit of L-PA was 1.10 nM with the fluorescence color changed from blue to green. Meanwhile, the up-conversion fluorescence system at excitation wavelength of 700 nm (ex: 700 nm) was used to detect Hg2+ and L-PA. The detection limits of Hg2+ and L-PA were 0.11 nM and 2.93 nM, respectively. The detection of Hg2+ and L-PA were also carried out based on the color extraction RGB values identified by the smartphone with a detection limit of 0.091 nM for Hg2+ and 8.97 nM for L-PA. In addition, the concentrations of Hg2+ and L-PA were evaluated by three-dimensional dynamic analysis in complex environments. The smartphone-assisted down/up-conversion dual-mode ratiometric fluorescence sensor system provides a new strategy for detection Hg2+ and L-PA in food safety evaluation, environmental monitoring and human health monitoring.

Generation of Prior Information in a Dual-Mode Microwave-Ultrasound Breast Imaging System.

A new breast imaging system capable of obtaining ultrasound and microwave scattered-field measurements with minimal or no movement of the breast between measurements has recently been reported. In this work, we describe the methodology that has been developed to generate prior information about the internal structures of the breast based on ultrasound data measured with the dual-mode system. This prior information, estimating both the geometry and complex-valued permittivity of tissues within the breast, is incorporated into the microwave inversion algorithm as a means of enhancing image quality. Several techniques to map reconstructed ultrasound speed to complex-valued relative permittivity are investigated. Quantitative images of two simplified dual-mode breast phantoms obtained using experimental data and the various forms of prior information are presented. Though preliminary, the results presented herein provide an understanding of the impacts of different forms of prior information on dual-mode reconstructions of the breast and can be used to inform future work on the subject.

Porous-Structure-Promoted Tribo-Induced High-Performance Self-Powered Tactile Sensor toward Remote Human-Machine Interaction.

Self-powered tactile sensor with versatile functions plays a significant role in the development of an intelligent human-machine interaction (HMI) system. Herein, a hybrid self-powered porous-structured tactile sensor (SPTS) is proposed by monolithically integrating a porous triboelectrification-induced electroluminescence (TIEL) component and a single-electrode triboelectric nanogenerator with the high charge generation in the bulk volume. At a low pressure of 10kPa, TIEL intensity can be significantly improved by three times, which is superior to that in previous reports, with enhanced triboelectricity. Based on the enhancement brought by the porous structure and optimized parameters, the SPTS achieves significant sensing performance in both optical and electrical modes. To demonstrate the potential of practical applications, a programmable optical and electrical dual-mode HMI system is established based on SPTS to remotely control an intelligent vehicle and operate a computer game through identifying finger touch trajectories. This work not only contributes a new economical-effective methodology toward a high-performance tribo-induced self-powered tactile sensor but also facilitates the remote control of HMI with dual-mode functionality, which has broad potential applications in the fields of intelligent robots, augmented reality, flexible wearable electronics, and smart home.

Design and control performance optimization of dual-mode hydraulic steering system for wheel loader

The traditional wheel loader performs the steering operation by the rotation of the steering wheel, which significantly increases the complexity and fatigue of the operator. This paper presents a dual-mode steering system to solve the afore-mentioned problems, where a pilot control valve with a joystick is connected in parallel with the redirector to control the hydraulic steering system. The steering speed and angle of the loader can be controlled by the swing angle and time of the joystick. Based on the simulation and experimental results, the proposed system has the same trend of pressure variation and good steering performance compared with the traditional steering system. The hydraulic damping diameter matching the steering system is obtained by simulating and optimizing the equivalent model. The experimental results show that the effective control swing angle of the joystick increased from 12.5° to 19.7°, which improves the control accuracy of the steering system.