Doped Fiber Amplifier Research Articles

Exploration of physical, structural, thermal, and optical properties of alkali zinc boro tellurite glasses doped with europium trioxide

In this present work we have studied the physical, structural, thermal, and optical properties of a new set of alkali zinc boro tellurite glasses doped europium trioxide prepared using the melt-quenching method. X-ray diffraction technique (XRD) and SEM were used to determine the non-crystalline property and microstructure property of the prepared samples. By using MAS-NMR spectroscopy and FTIR spectroscopy, the structural changes in the glasses were revealed. The physical properties were described by considering the densities of glass samples and hence molar volume, polaron radius, and oxygen packing density were measured. Thermal stability of glasses was perceived by performing DSC analysis and values ranges from 145 to 190 °C. Using UV–visible absorption spectra, it was possible to calculate the optical properties. The highest refractive index is found as 2.275 for glass AZBTE0 and the lowest is 2.241 for AZBTE5 glass. The ionic behaviour of the glasses was determined by electronegativity and values lie in the range of 1.51 to 1.688. The outcomes of the physical, thermal, and optical characteristics of glasses are intended for potential uses in optical switching and Europium doped fibre amplifier applications.

All-fiber spatial and wavelength gain-flattening of few-mode EDFA via mode selective coupler

The mode division multiplexing (MDM) technique together with wavelength division multiplexing (WDM) shows the great prospect to solve the capacity crunch of current standard single mode fiber (SSMF) transmission system. However, the modal and wavelength gain fluctuation fundamentally limit both the capacity and the reach of hybrid MDM-WDM transmission system. Here, we propose an all-fiber few-mode gain-flattening filter (FM-GFF) based on mode selective coupler (MSC), to effectively mitigate the gain fluctuation of few-mode erbium doped fiber amplifier (FM-EDFA) in both spatial and wavelength dimensions. With the help of genetic algorithm (GA), variable mode dependent loss spectra of cascaded MSCs can be efficiently obtained, according to the gain profile of the used FM-EDFA. Consequently, gain-flattening among all guided linearly polarized (LP) mode groups over the C-band can be realized. Simulation results reveal that, as for the spatial and wavelength gain flattening among 4/6-LP mode groups, only 5/7 cascaded MSCs are good enough to mitigate the modal and wavelength gain fluctuation from 9.89 dB and 11.79-dB to less than 0.38 dB and 0.46 dB over the C-band. Finally, we carry out experimental verification based on 2-LP mode groups gain flattening over C-band. When 3 cascaded MSCs are involved, the gain fluctuation of FM-EDFA over the C-band can be flattened from 2.46 dB to less than 0.96 dB.

Low-modal-crosstalk doped-fiber amplifiers in few-mode-fiber-based systems

Independent light propagation through one or multiple modes is commonly considered as a basic demand for mode manipulation in few-mode fiber (FMF)- or multimode fiber (MMF)-based optical systems such as transmission links, optical fiber lasers, or distributed optical fiber sensors. However, the insertion of doped-fiber amplifiers always kills the entire effort by inducing significant modal crosstalk. In this paper, we propose the design of doped-fiber amplifiers in FMF-based systems adopting identical multiple-ring-core (MRC) index profiles for both passive and doped fibers to achieve low modal crosstalk. We develop the direct-glass-transition (DGT) modified chemical vapor deposition (MCVD) processing for precise fabrication of few-mode erbium-doped fibers (FM-EDFs) with MRC profiles of both refractive index and erbium-ion doping distribution. Then, a few-mode erbium-doped-fiber amplifier (FM-EDFA) with a maximum gain of 26.08 dB and differential modal gain (DMG) of 2.3 dB is realized based on fabricated FM-EDF matched with a transmission FMF supporting four linearly polarized (LP) modes. With the insertion of the FM-EDFA, 60 + 60 km simultaneous LP01/LP11/LP21/LP02 transmission without inter-modal multiple-input multiple-output digital signal processing (MIMO-DSP) is successfully demonstrated. The proposed design of low-modal-crosstalk doped-fiber amplifiers provides, to our knowledge, new insights into mode manipulation methods in various applications.

A double clad ASE Re-injected hybrid TDFA and HDFA amplifier with ±1.44 dB GF

Abstract Current developments in wireless communications accentuate the exigency of high gain, low noise figure (NF) and minimum gain fluctuations (GF) based optical amplifier in 1.9–2.15 μm eye safe wavelength band. Hybrid thulium (Tm) doped fiber amplifier (TDFA) and holmium (Ho) doped fiber amplifier (HDFA) are the perfect candidates to extend the bandwidth towards 2 μm long wavelengths. In this work, amplifier spontaneous emission (ASE) re-injected double clad TDFA-HDFA hybrid amplifier using Fiber bragg gratings (FBGs) is presented for the amplification of 64 wavelength division multiplexed (WDM) channels covering 63 nm wavelength window. Further, performance of proposed amplifier with and without ASE reinjection is evaluated in terms of Gain, NF, GF and optical signal to noise ratio (OSNR). Effects of single and double clad on the Gain are studied and optimization of Tm and Ho doped fiber length, pump powers, and input power has also been accomplished. The GF as low as ±1.44 dB, Gain >28 dB, NF < 5.08 dB, output power 4.2 W are achieved in ASE re-injected configuration using 785 nm pump at 55 dBm in TDFA and 1,900 nm pump at 20 dBm in HDFA. It is noticed that double clad and ASE reinjection in TDFA and HDFA offer better GF.

Polarization Influence on Er3+-Doped Multi-Wavelength Brillouin Fiber Laser Based on Fiber Loop Mirror

Polarization influences on the performance of multi-wavelength Brillouin Er3+-doped fiber laser are investigated by adjusting the polarization controller (PC) in the fiber loop mirror (FLM), where the linear laser cavity is composed of a fiber-tailed mirror and an FLM, and the stimulated Brillouin scattering (SBS) and the Er3+-doped fiber amplification (EDFA) simultaneously serve as the cavity gain. We realized 1–7 Brillouin laser lines by increasing the 980 nm pump power. For the first-order Brillouin laser, the signal–noise ratio (SNR) and optical intensity present a sinusoidal envelope; the conversion efficiency changes significantly from 0.56465 dBm/mw to 0.44975 dBm/mw by adjusting the ring’s angle in the PC; the first-order SBS thresholds are 20.4 mw, 36.1 mw and 28.5 mw at different angles θ2 = 36°, 276° and 300°, respectively; flatness between the two Brillouin lasers change obviously from 2.863 dB to 41.801 dB with different ring angles; the second-order Brillouin laser is suppressed and disappears finally at Δθ2 = −64° to −84° and 106°~136° angle variation. For the fifth-order Brillouin laser, the highest-order Brillouin laser line is seriously suppressed until it disappears at some angle variations similarly. The powers and wavelength stabilities for one-, three- and seven-wavelength Brillouin fiber lasers were measured in 1 h, and the obtained Er3+-doped multi-wavelength Brillouin fiber laser (MWBFL) worked stably during that time, but the stabilities become worse with higher SBS orders.

All-optical wavelength reuse for meter reading application using EDFA saturation and DFB laser

The experiment utilizes the all-optical wavelength reuse for the realization of a cheaper meter reading approach. We demonstrate the all- optical wavelength reuse approach while exploiting a holding beam and the gain saturation of the erbium doped fiber amplifier (EDFA). A 10 Gb/s data is used to modulate a distributed feedback laser (DFB) and is transmitted downstream over 50 km. The saturated EDFA lowered the downstream data’s extinction ratio (ER) from 9.678 dB to 0.701 dB which is significant for both wavelength reuse and data rewrite for upstream transmission of meter reading as it facilitates the direct reuse of the downstream carrier without the addition of another electrical eraser for meter reading application. The variation of ER and the corresponding Peak to Peak power with EDFA input power for a 1550 nm 10 Gb/s DFB laser was demonstrated by Changing the bias current while maintaining the modulation voltage at 0.5 V allowed the input power into the EDFA to be adjusted from −7.278 dBm to 1.079 dBm. The performance analysis for upstream and downstream transmission was done and the receiver sensitivities determined at BER 10−9. The various eye diagrams were also analyzed for back-to-back (B2B) and 50 km upstream link and downstream link transmissions. This work is crucial for offering an all-optical wavelength reuse option for electrical meter reading application. In addition, the technique is all-optical and can therefore be able to support ultrafast systems with higher formats of modulation while ensuring efficiency in power.

High-gain ultra-wideband bismuth-doped fiber amplifier operating in the O + E + S band.

We present a double-pass bismuth (Bi)-doped fiber amplifier (BDFA) providing high-gain wideband amplification from 1330 to 1480 nm. A peak gain of 38 dB with 4.7 dB noise figure (NF) was obtained at 1420 nm for a -23 dBm input signal, with >20 dB gain from 1335 to 1475 nm. We achieved 30 and 21.5 dB peak gains with 122 nm (1341-1463 nm) and 140 nm (1333-1473 nm) 6 dB-gain bandwidth for -10 and 0 dBm input signal, respectively. For a 0 dBm signal, the power conversion efficiency (PCE) reached 23.7%, and the in-band optical-signal-to-noise ratio (OSNR) across the wideband BDFA was >44 dB. Also, the absorption and luminescence characteristics have been studied for different Bi-doped phosphosilicate fibers (BPSFs) fabricated in-house.

5.4 W, 2.35 µm cascaded Raman fiber laser pumped by dissipative soliton resonance-like pulses

We present a nonlinear amplifying loop mirror-based mode-locked fiber laser. By adjusting the pump power, the proposed laser exhibits a dissipative soliton resonance (DSR)-like pulse operation with a maximum pulse width of 150 ns. Subsequently, a three-stage Tm3+-doped fiber amplifier is implemented using a single-mode double-cladding Tm3+-doped fiber to increase the DSR-like pulse output power to 52.5 W, achieving a pump slope efficiency of 47.1% in the main amplifier. A 25 m first-order Raman-gain fiber (UHNA7) is pumped by a DSR-like pulse, and 16.3 W of pure 2.135 µm first-order Raman light with a spectral purity of 73.4% is obtained. Finally, 5.4 W of 2.35 µm second-order Raman light with a spectral purity of 66% is obtained using a 10 m 98% germania-core fiber as a second-order Raman-gain fiber cascaded after UHNA7 fiber. To the best of our knowledge, this is the highest output power ever obtained from a 2.3 µm laser.

Investigation of the few-mode ytterbium-erbium doped fiber amplifier including effects of ion clustering and secondary energy transfer

Investigation of the few-mode ytterbium-erbium doped fiber amplifier including effects of ion clustering and secondary energy transfer

Pair induced quenching in high concentration Holmium-doped fiber amplifiers

The spectrum required for future optical communication systems is being extended towards the C-, L- and U-bands, resulting in a significant interest in the spectral region around 2 μm wavelength. Since Holmium doped fiber amplifiers (HDFAs) provide amplification in this spectral region, they have become a focus of researchers working on doped fiber amplifiers. A major factor resulting in the performance degradation of HDFAs is the inhomogeneous energy transfer within Ho3+ ion-pairs in high-concentration Holmium-doped fibers (HDFs), an effect generally known as pair-induced quenching (PIQ). In this paper, we study the luminal and temporal dynamics of pulses of different repetition rates at 2.05 μm in high-concentration HDFs considering the effects of ion-pairs. Input pulses having repetition rates of 25 GHz and 500 kHz are generated using wavelength tunable actively mode-locked Holmium-doped fiber laser (AML-HDFL) based on a single ring cavity and bidirectional pumping. The characteristics of the pulses propagating through high-concentration HDF are analyzed based on different metrics such as average power, peak power, pulse energy, full-width at half maximum (FWHM), and time delay without and with ion-pairs for values of fraction of ion-pairs k = 0 and k = 10%, respectively. The results obtained at optimized length of HDF show that ion-pairs significantly degrade the average power, peak power, and energy of the output pulses for both of the repetition rates. For both k = 0 and k = 10%, the FWHM and shape of the output pulses remain same in the presence of the ion-pairs while, time delay of 4 ps and 19 ns is observed in the output pulses at repetition rates of 25 GHz and 500 kHz, respectively. The effects of increasing the pump and signal power on the average power and energy of the output pulses for k = 0 and k = 10% are also discussed for both repetition rates. This analysis provides important guidelines for designers of 2 μm fiber lasers and amplifiers based on high-concentration HDFs.

Optimizing High Data Rate Up to 2.5 Tbps Transmission using 64-Channel DWDM System with DCF and NRZ Modulation

Objectives: This study aims to enhance and optimize a modern communication system for high data rate transmission using Dense Wavelength Division Multiplexing (DWDM). The objectives include employing a 64-channel DWDM system, implementing different data speeds, and utilizing a dispersion compensation method. Methods: To achieve the objectives, we simulate and analyze the effects of Dispersion Compensation Fiber (DCF) in a DWDM system with 64 channels. The system employs Non-Return-to-Zero (NRZ) modulation format at varied bit rates and multiple energy levels. We propose a method for achieving data rates of 10 to 40 Gbps using NRZ modulation and Erbium-Doped Fiber Amplifier (EDFA) over a single-mode fiber transmission distance of 40 to 160 km, along with a dispersion compensation fiber of 8 to 32 km (DCF). The performance of the developed model is evaluated based on Quality Factor, Bit Error Rate (BER), Eye Height, and Threshold. These metrics are measured at two input energy levels from an optical power source, covering a communication capacity ranging from 0.625 Tbps to 2.5 Tbps. Findings: Through the simulations and analyses, we uncover the impact of dispersion and demonstrate the effectiveness of the proposed method in compensating for dispersion effects. Performance analysis of two different input transmitter power levels, -10 dBm is more efficient compared to 0 dBm input transmitter power in terms of bit error rate and quality factor. Novelty: This study presents a novel approach to improving modern communication systems by utilizing DWDM with a dispersion compensation method. The use of a 64-channel DWDM system, combined with the proposed NRZ modulation technique and dispersion compensation fiber, provides an efficient solution for achieving high data rates over long transmission distances while minimizing the effects of dispersion. The findings contribute to the advancement of communication systems for high data rate transmission. Keywords Dispersion effect, Bit Error Rate, Q-factor, Optisystem software, Erbium doped fiber amplifier

Temperature eigenfunction basis for accelerated transverse mode instability simulation.

This work presents a model for the simulation of transverse mode instability (TMI) in rare earth doped optical fiber amplifiers. The model evaluates the internal temperature of a fiber using a superposition of a finite number of thermal eigenmodes. This simplification greatly enhances the speed of calculation with negligible impact on calculation accuracy. This new method is described and quantitatively compared to an older model that uses standard, spatially resolved FDTD to integrate the heat diffusion equation. When tested over a range of spatial and temporal resolutions, this model reduces runtime by a factor of ∼13.9 on average relative to identical simulations using the spatially resolved model.

Power-aware high-capacity elastic optical networks

The power consumption of telecommunication equipment has been identified as a relevant contributor to global energy consumption. In fact, new-generation optical transponders employ power-intensive electronic application-specific integrated circuits (ASICs) for digital signal processing (DSP). DSP design has traditionally prioritized meeting transmission requirements over power consumption optimization. In general, the evolutions of transmission techniques and network design have always been mainly driven by traffic increase; in this context, in order to operate network resources more efficiently, margin reduction has been investigated in the past few years. Indeed, traditionally, high physical layer margins are used to ensure reliability over an extended period, resulting in overprovisioning the optical connections for both physical layer conditions and capacity. On the other hand, super-channels have emerged as a suitable solution for accommodating the continuous traffic growth. However, power consumption has not been deeply considered in the optimization of super-channel transmission. This paper first investigates the power efficiency of super-channels operated with designed and reduced margins. Low-margin operation is enabled by adapting sub-carrier spacing and filter bandwidth. Power-aware super-channel optimization is then experimentally demonstrated leveraging a 600 Gbit/s transponder in the SDN-controlled elastic optical network (EON). The results have identified a trade-off between power consumption and spectrum efficiency. Furthermore, the ongoing bandwidth demand has motivated the investigation of multi-band (MB) transmission for scaling the capacity of the existing infrastructures. However, novel networking devices (e.g., optical amplifiers operating beyond the C- and L-bands) will affect the overall power consumption. In this context, experimental power analysis of a thulium doped fiber amplifier (TDFA) is performed based on the traffic load and corresponding configuration. The results show that TDFA power consumption varies with configuration and increases with output power.

Four bits data sequence generators based ytterbium doped fiber amplifiers for upgrading maximum Q factor and minimum BER

Abstract We have simulated four bits data sequence generators based ytterbium-doped fiber amplifiers for upgrading max. Q factor and min. BER. Optical power variations against time duration after fiber cable length of 250 km with the bits sequence generators of 0101, 1000, and 1010 respectively are simulated. As well as the electrical power/total received power variations against frequency after photodetector receiver with the bits sequence generators of 0101, 1000, and 1010 respectively are discussed in details. Moreover, the signal power amplitude level with the time period duration after photodetector receiver/3R regenerator with the bits sequence generators of 0101, 1000, and 1010 respectively are clarified to show the max. Q factor and min. BER values for each case.

Design of A Chaos-based Digital Radio over Fiber Transmission Link using ASK Modulation for Wireless Communication Systems

Secured broadband radio communications are becoming increasingly pivotal for high-speed connectivity in radio access networks, playing a crucial role in both mobile information systems and wireless IoT connections. This paper introduces a chaos-based two-channel digital radio communication system utilizing fiber optic radio transmission technology. The system comprises two radio channels operating at up to 1 Gbps using amplitude shift keying (ASK) modulation, followed by modulation with a chaotic sequence before conversion to the optical domain using the MZM modulator. To compensate for fiber loss, the system utilizes an Erbium Doped Fiber Amplifier (EDFA) and employs the optical links through standard ITU-G.655 optical fibers. Numerical simulation of the designed system is performed using the commercialized simulation software Optisystem V.15 to assess and characterize transmission performance. The results demonstrate the system’s effective operation on two channels with a fiber transmission distance of up to 110 km, maintaining a bit error ratio of less than 10−9. This feature ensures reliable performance for high-speed radio connections, particularly in applications such as fronthaul networks in cloud radio access and wireless sensor network connections.

Characterization of Visible Range Gain in Praseodymium Doped Fiber Amplifier

In the optical (380-700 nm) region, a simulation study was conducted to assess the low-signal gain, power conversion efficiency (PCE), and optical output power of a praseodymium-doped fiber optic amplifier (PDFA). The PDFA performance was assessed using the optimized Pr3+ fiber length, Pr3+ ion concentration, and pump power. Additionally, the effects of input signal voltage and amplifier gain on amplified spontaneous emission (ASE) were investigated. A lower peak signal of roughly 1 dB at 635 nm was obtained with a shorter 5 m Pr3 + doped fiber and a higher pump power of 300 mW. The impact of wavelength and pump power variations on the amplifier's optical output power's spontaneous enhanced emission (EEM) is examined. Finally, the ionic interaction (general-purpose conversion effect) in the low-power amplifier signal is analyzed by taking into account various values of the upconversion factor. Keywords: Praseodymium doped fibre amplifier, Small-signal gain, Pump power, Ultrashort laser.

High-power, air-cooled Thulium doped fiber amplifier with 71% slope efficiency

High-power, air-cooled Thulium doped fiber amplifier with 71% slope efficiency

Suppression of stimulated Brillouin scattering effect in 2 μm narrow linewidth Tm3+-doped fiber amplifier based on phase-modulated waveform design

In this paper, we investigate the optimal design of phase modulation waveforms using the theoretical model of Tm3+-doped fiber amplifiers. The proposed design suppresses the SBS effect in the 2 μm-band Tm3+-doped fiber amplifiers with the help of a reference point-based multi-device non-dominated sequential genetic algorithm (NSGA-III). At the same time, synthesis efficiency is ensured. Different from the previous use of conventional multi-objective genetic algorithms to suppress the SBS effect in narrow linewidth amplifiers in the 1 μm band, the maximum SBS threshold is 121 W at a signal linewidth of 496 MHz with a more uniform distribution of Pareto solutions under this scheme. The signal linewidth of 680.61 MHz increases the SBS threshold by almost 20 W and the operating speed by several times compared to a conventional multi-objective genetic algorithm at different modulation depths, modulation frequencies and modulation periods. The threshold enhancement factor of the SBS signal with optimal modulation is 2.12 times that of the sinusoidal signal with an extended bandwidth of 700 MHz. The 2 μm laser obtained by this scheme enables more accurate and longer distance ranges in coherent detection.

A 75 GHz Brillouin Stokes Channels For High Data Rate DWDM Communication Systems

The experimental results of a 75 GHz Brillouin Stokes channels are demonstrated in this paper. Three dispersion compensation fiber (DCF) spools and one single mode fiber (SMF) spool are used as a Brillouin gain medium. An erbium doped fiber amplifier (EDFA) sections are used to amplify the generated Stokes channels and to reduce the Brillouin Stokes threshold inside the cavities. Laser pump of 1480 nm with total power of 470 mW are used for the EDFA sections as a pump power unit. In our proposed setup, four channels with 75 GHz spacing, high Stokes power of about 10 mW, and large optical signal to noise ratio (OSNR) of about 52 dB are achieved at Brillouin pump power of 25 mW. The achieved channels are tuned over 15 nm from 1565 to 1580 nm. within the entire tuning range up to 25 Stokes channels with 75 GHz spacing can be utilized. High data rate of about 800 Gb/s can be obtained per single channel at this wide channel spacing. Therefore, the total data rate that could be achieved within the obtained tuning range is about 20 Tb/s.

Improved Brillouin induced self-heterodyne method for measurement of narrow laser linewidth

In this paper, we present the improved stimulated Brillouin-induced self-heterodyne (ISISH) method that overcomes the effect of amplified spontaneous emission (ASE) noise of erbium doped fiber amplifier (EDFA) on linewidth measurements. In addition, we eliminate the beating effects of additional sideband during the measurement of narrow laser linewidth. Moreover, we experimentally demonstrate the effect of amplified spontaneous Brillouin scattering (ASBS) noise on the variation of the measured linewidth of the laser under test (LUT) with varying pump power. We measure the Brillouin amplifier gain, which is essential for the ISISH technique, as 13.5, 12.7 and 9.5 dB at the pump powers of 16, 12 and 8 mW, respectively. These results are consistent with the analytical values of 14, 13 and 12.5 dB at the same variations in pump powers as previously reported. Experimental results show the 20 dB linewidths of 4, 6.7 and 10 kHz at pump powers of 16, 12 and 8 mW, respectively. We also perform the stimulated Brillouin-induced self-heterodyne (SISH) method. However, in SISH, the obtained linewidth of the LUT differs by approximately 4, 4.3 and 5 kHz at the pump powers of 16, 12, and 8 mW, respectively. Furthermore, we investigate the effect of detuning on LUT linewidth measurement in the ISISH method. The 20 dB linewidths at 5 and 10 MHz detuned from the Brillouin peak at 16 mW pump power are 20 and 25 kHz, respectively. These values are significantly larger than the measured linewidth at the pump power of 16 mW without detuning.