Diversity Gain Research Articles

Superposed three-dimensional 64QAM constellation design for MIMO-OFDM visible light communication systems.

Multiple-input multiple-output orthogonal frequency division multiplexing (MIMO-OFDM) has been widely used to improve data rate in visible-light communication (VLC) systems. However, the high correlation of channels restricts the application of MIMO. A superposed constellation, combined with MIMO, can achieve considerable diversity gain even in highly correlated MIMO channels. In this study, what we believe to be novel superposed three-dimensional 64-quadrature amplitude modulation (3D-64QAM) constellation schemes are proposed for MIMO-OFDM VLC systems. First, a superposed 3D-64QAM constellation scheme using two transmitted light emitting diodes (LEDs) is proposed, where two independent signals with 3D-4QAM and 3D-16QAM modulation formats are superposed to form a 3D-64QAM signal at the receiver. Then, for what we believe is the first time, we expand the superposed constellation solution to three-LED application scenarios, wherein the 3D-64QAM constellation is superposed by three different 3D-4QAM constellations. Both schemes benefit from a higher minimum Euclidean distance of 3D-64QAM constellation, 1.67 times that of traditional two-dimensional (2D) 64QAM constellation. Meanwhile, the equal-power superposition design of transmitted signals reduces the nonlinearity of LEDs and power competition of photodiodes. Moreover, the three-LED scheme further improves the transmitted power without increasing the risk of nonlinear distortion. To improve spectral efficiency and reduce complexity, we also propose a 3D OFDM modulation scheme. The superposed 3D-64QAM schemes are first studied through theoretical analysis and computer simulation. Then, an experimental demonstration is established to investigate the system performance comprehensively. Experimental results prove that the superposed 3D-64QAM constellation schemes achieve a superior bit error rate (BER) performance than the traditional superposed 2D-64QAM constellation scheme. Compared with two-LED scheme, the three-LED scheme not only obtains a lower BER, but also improves the dynamic range of driving peak-to-peak voltage significantly.

Two closely spaced microstrip patches with high isolation for full-duplex/MIMO applications.

This paper shows an effective method to significantly enhance the isolation of a closely spaced two-port patch antenna, which can be deployed for full-duplex transceivers as well as multiple-input-multiple-output (MIMO) systems. Two rectangular microstrip patches are arranged in the E-plane configuration. To achieve high isolation, a grounded stub is positioned between the radiating patches. For validation of the proposed concept, an antenna prototype is fabricated for measurements. The measured data demonstrates that the port-to-port mutual coupling can be suppressed to -50 dB, which is useful in self-interference cancellation for full-duplex communication systems. Compared with the coupled design, the isolation is significantly enhanced by 43 dB with an inter-element spacing of 0.034λc, where λc is a free-space wavelength at the center operating frequency. Regarding MIMO metrics, the antenna also shows good MIMO diversity performance based on an envelope correlation coefficient and a diversity gain.

UAV-Aided Wireless Energy Transfer for Sustaining Internet of Everything in 6G

Unmanned aerial vehicles (UAVs) are a promising technology used to provide on-demand wireless energy transfer (WET) and sustain various low-power ground devices (GDs) for the Internet of Everything (IoE) in sixth generation (6G) wireless networks. However, an individual UAV has limited battery energy, which may confine the required wide-range mobility in a complex IoE scenario. Furthermore, the heterogeneous GDs in IoE applications have distinct non-linear energy harvesting (EH) properties and diversified energy and/or communication demands, which poses new requirements on the WET and trajectory design of UAVs. In this article, to reflect the non-linear EH properties of GDs, we propose the UAV’s effective-WET zone (E-zone) above each GD, where a GD is assured to harvest non-zero energy from the UAV only when the UAV transmits into the E-zone. We then introduce the free space optics (FSO) powered UAV with enhanced mobility, and propose its adaptive WET for the GDs with non-linear EH. Considering the time urgency of the different energy demands of the GDs, we propose a new metric called the energy latency time, which is the time duration that a GD can wait before becoming fully charged. By proposing the energy-demand aware UAV trajectory, we further present a novel hierarchical WET scheme to meet the GDs’ diversified energy latency time. Moreover, to efficiently sustain IoE communications, the multi-UAV enabled WET is employed by unleashing their cooperative diversity gain and the joint design with the wireless information transfer (WIT). The numerical results show that our proposed multi-UAV cooperative WET scheme under the energy-aware trajectory design achieves the shortest task completion time as compared to the state-of-the-art benchmarks. Finally, the new directions for future research are also provided.

A dual operating (27/38 GHz) high performance 2 × 4 MIMO antenna array for 5G new radio applications

This article presents an unique configuration of Multiple-Input Multiple-Output (MIMO) antenna array for functioning at 27/38 GHz millimeter-wave 5G new radio (NR) frequency bands applications. The suggested antenna is constructed with four MIMO elements, containing total of eight identical patches arranged in a 2 × 4 array configuration. The array also includes a separate non-connected rectangular ground plane with an overall dimension of 32.4 × 32.8 × 0.8 mm3. The single radiating patch elements are designed using spline resonator with H-shaped structures. The prototype model is realized using low cost FR-4 substrate and the obtained measurement results validate the analyzed simulated results. The suggested MIMO array antenna offers dual band operation with an impedance bandwidth of 8400 MHz covering 22 to 30.4 GHz and 8500 MHz ranging from 36.1 to 44.6 GHz. The proposed antenna achieves a peak gain of 8.75 dBi when operating at 27 GHz and 18.59 dBi at 38.1 GHz. Furthermore, it shows circular polarization characteristics by offering the axial ratio values significantly lower than 3 dB at 27 GHz and 38.1 GHz frequency bands. Additionally, the results indicate the favourable values of the diversity performance parameters with reference to Mean effective gain (MEG), Envelope correlation coefficient (ECC), Diversity gain (DG), Total active reflection coefficient (TARC), and Channel capacity loss (CCL). Moreover, it demonstrates high isolation (<−20 dB) within the desired bandwidth. These superior characteristics make it compatible for 5G NR frequency bands N257(26.5-29.5 GHz), N258 (24.5-27.5 GHz), N259 (39.5-43.5 GHz) and N260 (37-40 GHz), enabling its use in various countries including the China, European Union, Sweden, Korea, Japan, United States of America, Canada and Australia.

A compact bent microstrip-based wideband millimeter wave MIMO antenna for 5G applications

Abstract This paper proposes a wideband four-element multiple-input multiple-output (MIMO) antenna operating in the millimeter-wave frequency band for 5G communications from 24.37–39.44 and 45.09–50.62 GHz. The antenna design has been realized using Rogers 5880 substrate and consists of a T-shaped strip that is attached to the top of a 50 Ω feeding line. Two microstrip lines are affixed at the terminal points of T-shaped strip and bent toward the feeding structure. These bent strip lines are then extended by joining two additional L-shaped microstrip lines. On the back, there is a partial defective ground plane featuring a rectangular slot and a thin strip line located at its center. The dimensions of the proposed single element and MIMO antenna are 0.933λ × 0.933λ × 0.024λ and 1.865λ × 1.865λ × 0.024λ, respectively (at 28 GHz), while the edge-to-edge distance between the radiation elements of the MIMO antenna is 4.0 mm. The design incorporates an efficient passive fan-shaped decoupling structure to decrease coupling between antenna elements. Simulations and experimental results show good agreement with each other. For all resonant frequencies the measured peak gain is greater than 4.85 dBi, radiation efficiency is over 90%, diversity gain is greater than 9.5, ECC is less than 0.025, TARC is less than -10 dB and CCL is below 0.4 bits/s/Hz. The proposed MIMO antenna, with its wide bandwidth, high gain, high inter-port isolation, and high efficiency characteristics, can be used for 5G wireless communication applications.

Quasi-binomial series-fed array for performance improvement of millimeter-wave antenna for 5G MIMO applications

A quad-port MIMO antenna based on a quasi-binomial series-fed array is presented in this paper for n257 and n258 millimeter-wave applications with an investigation of additional loaded patches on performance enhancement of the conventional binomial series-fed array. The single element of the proposed MIMO is a 3 × 3 element planar binomial series-fed array whose width of the radiating elements is tapered to achieve the binomial distribution. From both simulated and tested results, it is observed that a wider bandwidth (S11 < –10 dB of 21.78 %), high peak gain (12.4 dBi), and high radiation efficiency (92 %) with side lobe level (SLL) reduction of more than 9 dB are achieved by additional loaded patches. This design approach does not only offer wider bandwidth, low SLL, and gain increment, but also ensures the excellent diversity performances of the very closely spaced (0.116λ) MIMO antenna, without utilizing any additional decoupling structure. The proposed MIMO antenna system offers impedance bandwidth (S11 < − 10 dB) from 24.6 GHz to 30.59 GHz, isolation > 27 dB, envelope correlation coefficient < 0.0002, diversity gain > 9.99 dB, and mean effective gain between –4 dB and –8 dB. Owing to its performance attributes, the proposed antenna is an excellent choice for 5G millimeter-wave communication devices, including but not limited to enormous IoT, smart cities, and virtual reality.

System outage probability and diversity analysis of a SWIPT based two-way DF relay network under transceiver hardware impairments

This paper investigates the system outage performance of a simultaneous wireless information and power transfer (SWIPT) based two-way decode-and-forward (DF) relay network, where potential hardware impairments (HIs) in all transceivers are considered. After harvesting energy and decoding messages simultaneously via a power splitting scheme, the energy-limited relay node forwards the decoded information to both terminals. Each terminal combines the signals from the direct and relaying links via selection combining. We derive the system outage probability under independent but non-identically distributed Nakagami-m fading channels. It reveals an overall system ceiling (OSC) effect, i.e., the system falls in outage if the target rate exceeds an OSC threshold that is determined by the levels of HIs. Furthermore, we derive the diversity gain of the considered network. The result reveals that when the transmission rate is below the OSC threshold, the achieved diversity gain equals the sum of the shape parameter of the direct link and the smaller shape parameter of the terminal-to-relay links; otherwise, the diversity gain is zero. This is different from the amplify-and-forward (AF) strategy, under which the relaying links have no contribution to the diversity gain. Simulation results validate the analytical results and reveal that compared with the AF strategy, the SWIPT based two-way relaying links under the DF strategy are more robust to HIs and achieve a lower system outage probability.

High Performance Antenna System in MIMO Configuration for 5G Wireless Communications Over Sub‐6 GHz Spectrum

AbstractThis paper presents a high‐performance multiple input and multiple output (MIMO) antenna comprising 2 × 2 configuration of radiating elements that is designed for sub‐6 GHz applications. The proposed MIMO antenna employs four identical radiating elements. High isolation between the radiating elements and therefore reduced mutual coupling is achieved by spatially arranging the radiating elements in an orthogonal configuration. Also, a novel frequency selective surface (FSS) was employed to increase the gain of the MIMO antenna over a wide bandwidth from 3 to 6 GHz. This was achieved by locating the FSS above the antenna at a certain height. The FSS essentially enhanced the antenna's directivity, reduced back lobe radiation and mutual coupling. The antenna was fabricated on a standard Rogers RT Duroid 5880 dielectric substrate with a 0.8 mm thickness. The overall dimension of the MIMO antenna is 50 × 50 × 12.5 mm3 and it operates from 3.8 to 6 GHz, which corresponds to a fractional bandwidth of 41%. The proposed MIMO antenna has a measured peak gain of 4.8 dBi and inter radiation element isolation &gt;20 dB. Its envelope correlation coefficient is &lt;0.1 and diversity gain &gt;9.9 (dB). These characteristics make the proposed MIMO antenna system suitable for 5G communication systems.

Differential beamforming using Rotman lens for wireless sensor networks

In this article, an optimal beamforming technique using a low cost intelligent Rotman lens antenna is proposed. The proposed technique enjoys full diversity with high coding gain, has a very low encoding and decoding complexity, and does not require channel knowledge at any transmitting or receiving antenna. From our simulation results, the proposed technique outperforms the best known non-coherent multi-antenna techniques. Furthermore, we prove that the BER expressions obtained from the theoretical analysis enjoy full diversity gain and match our conducted simulations.

Complementary Coded Identical Code Cyclic Shift Multiple Access Under Asynchronous Frequency-Selective Fading Channels

A complementary coded code-division multiple-access (CC-CDMA) system is built on the direct sequence (DS) spread spectrum technique, which can suppress multipath interferences and multiple-access interferences due to the ideal correlation property of complementary codes (CCs). However, the DS spread spectrum technique will cause poor bandwidth efficiency; the CC-CDMA system suffers from serious interferences due to the ideal correlation of CCs may not be reconstructed at the receiver after passing through asynchronous frequency selective fading channels. In this paper, we propose a complementary coded identical code cyclic shift multiple access (CC-ICCSMA) system under asynchronous frequency selective fading channels, which allows multiple data streams to transmit in parallel by sharing one spreading code for improving the bandwidth efficiency. Considering the impact of interferences, we propose an ICCS matched filterbank to tackle the interferences, which can decode the data under all paths and achieve a high multipath diversity gain. Simulation results show that the proposed CC-ICCSMA system can achieve higher bandwidth efficiency than that of traditional CC-CDMA and can outperform the traditional DS-CDMA schemes in terms of bit-error rates and transmission rates.

A High-Frequency Planar-Configured Millimeter-Wave MIMO Antenna for Fifth-Generation NR Operations

This article presents a simple planar millimeter-wave (mm-wave) multiple input multiple output (MIMO) antenna with four closely spaced radiating elements. The antenna is intended to enhance the bandwidth for 5G new radio (NR) applications and also cover the industrial Ka-band (26.5-40 GHz), Q-band (30-50 GHz), and U-band (40-60 GHz) frequency ranges. The antenna is designed using Rogers RT/duroid 5880 substrate with a size of 25 × 26 × 1.6 mm3. The proposed antenna consists of four identical radiating elements with two of them positioned in a linear configuration facing each other, while the other two elements are placed opposite to the first two, which improves isolation between the elements. Across the entire operating frequency range (26-60 GHz), the antenna demonstrated excellent performance, including 34 GHz wide bandwidth, high isolation of &gt;25 dB, nearly omnidirectional radiation patterns, high gain of 11.1 dB with a high radiation efficiency of 94%, low envelope correlation coefficient (ECC) of 0.0068, and high diversity gain (DG) of 9.967 dB. The simulated findings exhibit a strong positive correlation with the experimental results. The proposed MIMO antenna design is a promising solution for 5G NR applications.

Design of a Modified MIMO Antenna Based on Tweaked Spherical Fractal Geometry for 5G New Radio (NR) Band N258 (24.25–27.25 GHz) Applications

This article describes a fractal-based MIMO antenna for 5G mm-wave mobile applications with micro-strip feeding. The proposed structure is a fractal-based spherical configuration that incorporates spherical slots of different iterations on the patch, as well as rectangular slots on the ground plane. These additions are meant to reduce patch isolation. The two-element MIMO antenna has closely spaced antenna elements that resonate at multiple frequencies, 9.5 GHz, 11.1 GHz, 13.4 GHz, 15.8 GHz, 21.1 GHz, and 26.6 GHz, in the frequency range of 8 to 28 GHz. The antenna’s broadest operational frequency range spans from 17.7 GHz to 28 GHz, encompassing a bandwidth of 10,300 MHz. Consequently, it is well-suited for utilization within the millimeter wave (mm wave) application, specifically for the 5G new radio frequency band n258, and partially covers some other bands X (8.9–9.9 GHz, 10.4–11.4 GHz), and Ku (13.1–13.7 GHz, 15.4–16.2 GHz). All the resonating bands have isolation levels below the acceptable range of (|S12| &gt; −16 dB). The proposed antenna utilizes a FR4 material with dimension of 28.22 mm × 44 mm. An investigation is conducted to analyze the effectiveness of parameters of the antenna, including radiation pattern, surface current distributions and S parameters. Furthermore, an examination and assessment are conducted on the efficacy of the diversity system inside the multiple input multiple output (MIMO) framework. This evaluation encompasses the analysis of key performance metrics such as the envelope correlation coefficient (ECC), diversity gain (DG), and mean effective gain (MEG). All antenna characteristics are determined to be within a suitable range for this suggested MIMO arrangement. The antenna design underwent experimental validation and the simulated outcomes were subsequently verified.

Miniaturized MIMO antenna design based on octagonal-shaped SRR metamaterial for UWB applications

A miniaturized antenna based on octagonal-shaped split ring resonator (O-SRR) metamaterial and CPW-feeder technique for ultra-wideband (UWB) applications is developed in this research. The structure of the component cell monopole antenna is designed by using a triangle-shaped fractal method and merging metamaterial implementation with the L-stub shape. These techniques provide a wide impedance bandwidth for the innovative wireless antenna, which operates from 2.46 to 13.98 GHz. The planned module cell dimensions are 20 by 16 square millimetres (0.164λL×0.131), where the wavelength (λL) is 121.95 mm. This low-profile antenna has then been employed to design an array of 2 × 2 Multi Input Multi Output (MIMO) antennas with an overall size of 20 × 34 mm2. Two symmetric antennas are arranged in the designed miniaturized MIMO system with an inverted T-shaped decoupling copper between them. Measurement results show that the dual antenna with multiple diversity metrics has great characteristics for MIMO applications due to providing low mutual coupling value, lower than 0.30 bits per s. /Hz of channel capacity loss, minor envelope correlation coefficient of fewer than 0.003, lower −10 dB of total active reflection coefficient, greater than 9.96 dB of diversity gain and proper mean effective gain (MEG ratio ≈ 1, MEG ≤ 0.5). A high peak gain magnitude of 5.71 dBi is provided at an operating frequency of 13.2 GHz for the recommended single antenna.

Ten-Port MIMO Inverted-F Antenna for LTE Bands 43/48/49 Bands Smartphone Applications

This paper presents a design and performance analysis of a 10-element 5G massive Multiple Input Multiple Output (m-MIMO) antenna array for sub-6 GHz mobile handsets, specifically for Long Term Evolution (LTE) bands 43 (3600–3800 MHz) and 48/49 (3550–3700 MHz) applications. The proposed antenna array consists of ten closely spaced inverted-F antennas with a compact size of 20 × 9 mm2 of a single element. The proposed antenna array provides high efficiency and low correlation between the antenna elements, which result in increased data rate and enhanced signal quality. The performance of the antenna array is evaluated in terms of the radiation pattern, diversity gain, efficiency, and correlation coefficient. The simulation and measured results show that the proposed antenna array achieves an approximate peak gain of 2.8 dBi and a total efficiency of 65% at the resonance frequency of 37 GHz and a low correlation coefficient of 0.07 between the adjacent antenna elements. Moreover, the single and two-hand modes are also given in order to highlight the potential of such a structure as a smart mobile terminal. The simulated results are discovered to be in excellent agreement with the measured values. We think this structure has a bright future in the next generation of smart mobile phones based on the performance and the measured findings.

A Quad-Port Nature-Inspired Lotus-Shaped Wideband Terahertz Antenna for Wireless Applications

This article is aimed at designing an inventive compact-size quad-port antenna that can be operated within terahertz (THz) frequency spectra for a 6G high-speed wireless communication link. The single-element antenna comprises a lotus-petal-like radiating patch and a defected ground structure (DGS) on a 20 × 20 × 2 µm3 polyamide substrate and is designed to operate within the 8.96–13.5 THz frequency range. The THz antenna is deployed for a two-port MIMO configuration having a size of 46 × 20 × 2 µm3 with interelement separation of less than a quarter-wavelength of 0.18λ (λ at 9 THz). The two-port configuration operates in the 9–13.25 THz frequency range, with better than −25 dB isolation. Further, the two-port THz antenna is mirrored vertically with a separation of 0.5λ to form the four-port MIMO configuration. The proposed four-port THz antenna has dimensions of 46 × 46 × 2 µm3 and operates in the frequency range of 9–13 THz. Isolation improvement better than −25 dB is realized by incorporating parasitic elements onto the ground plane. Performance analysis of the proposed antenna in terms of MIMO diversity parameters, viz., envelope correlation coefficient (ECC) &lt; 0.05, diversity gain (DG) ≈ 10, mean effective gain (MEG) &lt; −3 dB, total active reflection coefficient (TARC) &lt; −10 dB, channel capacity loss (CCL) &lt; 0.3 bps/Hz, and multiplexing efficiency (ME) &lt; 0 dB, is performed to justify the appropriateness of the proposed antenna for MIMO applications. The antenna has virtuous radiation properties with good gain, which is crucial for any wireless communication system, especially for the THz communication network.

SAR assessment of miniaturized wideband MIMO antenna structure for millimeter wave 5G smartphones

This work introduces a wideband two-element Multiple-Input Multiple-Output (MIMO) antenna array that covers the desired frequencies of 28/38 GHz for millimeter-wave (mmW) 5G smartphones. The antenna array demonstrates significant isolation and gain increase based on dual-mode planar dipole antennas. The proposed structure was designed using CST Microwave Studio 2019. The design is implemented on a Rogers RT 4003 substrate measuring 14.76 × 8.38 mm2 with a dielectric constant of 3.55. It features two planar dipole antennas positioned at the corners in a perpendicular arrangement to each other. To achieve the desired wideband performance, each element consists of a dipole antenna and a partial ground plane. The spacing between elements, including the parasitic element (PE), is set to 0.5λ₀ to increase isolation between the MIMO antenna elements while keeping complexity and cost to a minimum. Simulation results demonstrate an improvement in mutual coupling between array members, with measured values ranging from −55 dB to −75 dB. The envelope correlation coefficient (ECC) is also improved. Furthermore, enhancements are observed in the total active reflection coefficient (TARC), mean effective gain (MEG), and diversity gain (DG). The measured gains of the proposed designs range from 6 dBi across the entire band to 10 dBi at 40 GHz, with a radiation efficiency close to 95%. The antenna performs well in the presence of the handset and human head model during simulation. The study identifies a safe and acceptable specific absorption rate (SAR) value, which provides a low SAR10g of about 0.963 W/Kg at 28 GHz and 0.583 W/Kg at 38 GHz. while maintaining superior efficiency and radiation patterns. When the antennas are constructed and tested, the experimental results surpass the modeling results. The simulation and test findings demonstrate a satisfactory fit within the target band, suggesting that the proposed structure could be applied to millimeter-wave 5G smartphones.

The Design and Investigation of a Super Wideband Antenna with Dual-Band Notch Characteristics for MIMO Application

A printed monopole super wideband (SWB) antenna is presented in this paper. It consists of a beveled-shaped radiator and a tapered ground plane. It is investigated that tapering of the radiator and ground plane enhances the impedance matching and results in broad impedance bandwidth. The experimental result depicts that the antenna achieved 164.9% impedance bandwidth from 2.6 to 27.27 GHz. Furthermore, to prevent the interference caused by communication systems within the ultra-wideband (UWB) range, dual-band rejection at Wi-MAX (2.7–4 GHz). and X-band (8.5–12 GHz) are introduced by etching an H-shape and two back-to-back C-shaped notches in the radiator and feedline, respectively. The measured result demonstrates that both slots effectively reject the desired frequency bands with a small shift in the lower frequency edge from 2.41 to 2.6 GHz. In addition, the proposed antenna application is shown in the two elements MIMO system where a bowtie decoupling structure is utilized to improve the isolation. It is found that the presence of a decoupling structure improves the isolation by up to 60%. To characterize the diversity performance, parameters such as Diversity Gain (DG), Envelop Correlation Coefficient (ECC), Channel Capacity Loss (CCL), and Mean Effective Gain (MEG) are calculated and all are found in the acceptable limit.

A Novel Adaptive UE Aggregation-Based Transmission Scheme Design for a Hybrid Network with Multi-Connectivity

With the progress of the eras and the development of science and technology, the requirements of device-to-device (D2D) connectivity increased rapidly. As one important service in future systems, ultra-reliable low-latency communication (URLLC) has attracted attention in many applications, especially in the Internet of Things (IoT), smart cities, and other scenarios due to its characteristics of ultra-low latency and ultra-high reliability. However, in order to achieve the requirement of ultra-low latency, energy consumption often increases significantly. The optimization of energy consumption and the latency of the system in the communication field are often in conflict with each other. In this paper, in order to optimize the energy consumption and the latency jointly under different scenarios, and since the detailed requirements for latency and reliability are diverse in different services, we propose an adaptive UE aggregation (AUA)-based transmission scheme that explores the diversity gain of multiple simultaneous paths to reduce the overall latency of data transmission, wherein multiple paths correspond to multiple coordination nodes. Furthermore, it could provide the feasibility of link adaptation by adjusting the path number according to the real transmission environment. Then, unnecessary energy waste could be avoided. To evaluate the performance, the energy-delay product (EDP) is proposed for the latency and energy comparison. The provided simulation results align with the numerical data. Through the analysis, it can be proven that the proposed scheme can achieve a joint optimization of latency and energy consumption to meet different types of URLLC services.

Electromagnetic coupling shielding in compact MIMO antenna using symmetric T-shaped metamaterial structure for 5G communications

In this paper, a new symmetric metamaterial (MM) based T-shaped shield is proposed to enhance isolation between antenna elements in a two-antenna multiple-input-multiple-output (MIMO) system useful for 5G wireless communications. The proposed antenna is designed with two adjacent H-plane coupled dumbbell-shaped slotted rectangular patches and parasitic stubs with a small center-to-center gap of 0.39λmin at 4.5 GHz. The antenna is developed using FR-4 epoxy low-cost substrate with a compact size of 0.45λmin × 0.75λmin × 0.048λmin to cover the 5G n79 band of 4.5–5.01 GHz (10.73%). The T-shaped MM shield is comprised of a hanging hook shape unique symmetric resonator with near-zero permeability, epsilon negative (ENG), and negative refractive index (NRI) properties, which shows excellent band-stop characteristics within the antenna bandwidth. The designed T-shaped shield is employed in the middle of the two MIMO antennas, enhancing isolation to > 28.5 dB by greatly suppressing the near-field mutual coupling energy. Moreover, the antenna impedance bandwidth is improved by 3.95% and the envelope correlation coefficient (ECC) is reduced from 0.003 to 0.0006 (0.02 to 0.01 for radiation) within the desired band, confirming high isolation and excellent channel capacity. Furthermore, an outstanding diversity gain (DG) > 9.99 dB and low channel capacity loss (CCL) < 0.3 bits/s/Hz are achieved by the proposed MM shielding. The effectiveness of the proposed MM shielding technique is verified by the measurement of the MIMO prototype and shows promising performance for 5G MIMO applications.

Design of Multi-User Noncoherent Massive SIMO Systems for Scalable URLLC.

This paper develops and optimizes a non-orthogonal and noncoherent multi-user massive single-input multiple-output (SIMO) framework, with the objective of enabling scalable ultra-reliable low-latency communications (sURLLC) in Beyond-5G (B5G)/6G wireless communication systems. In this framework, the huge diversity gain associated with the large-scale antenna array in the massive SIMO system is leveraged to ensure ultra-high reliability. To reduce the overhead and latency induced by the channel estimation process, we advocate for the noncoherent communication technique, which does not need the knowledge of instantaneous channel state information (CSI) but only relies on large-scale fading coefficients for message decoding. To boost the scalability of noncoherent massive SIMO systems, we enable the non-orthogonal channel access of multiple users by devising a new differential modulation scheme to ensure that each transmitted signal matrix can be uniquely determined in the noise-free case and be reliably estimated in noisy cases when the antenna array size is scaled up. The key idea is to make the transmitted signals from multiple geographically separated users be superimposed properly over the air, such that when the sum signal is correctly detected, the signal sent by each individual user can be uniquely determined. To further enhance the average error performance when the array antenna number is large, we propose a max-min Kullback-Leibler (KL) divergence-based design by jointly optimizing the transmitted powers of all users and the sub-constellation assignments among them. The simulation results show that the proposed design significantly outperforms the existing max-min Euclidean distance-based counterpart in terms of error performance. Moreover, our proposed approach also has a better error performance compared to the conventional coherent zero-forcing (ZF) receiver with orthogonal channel training, particularly for cell-edge users.