Distribution Of CNTs Research Articles

CONSOLIDATION OF CNT-REINFORCED AA4032 NANOCOMPOSITES BY ECAP

The present work emphasizes on the synthesis of CNT-reinforced nanocrystalline AA4032 alloy powders and their consolidation by equal channel angular pressing (ECAP). Nanocrystalline AA4032 alloy reinforced with 2 wt% CNTs was produced by high-energy ball milling. The XRD analysis and TEM observation revealed the formation of nanocrystalline AA4032 alloy and uniform distribution of CNTs in the nanocrystalline matrix. The nanocomposite powders were canned in commercially pure aluminum sheath and subjected to ECAP for consolidation. More than 98% of density was achieved after four passes in route BA at the center of the can. The hardness obtained is around 218 HV5.0 after four passes in the core of alloy with 2 wt% of CNTs. Increase in hardness was significant even with minimum addition of CNTs.

Tribological Behavior of Aluminum-CNT Coated Metal Composite Under Dry and Water Lubricated Conditions

Carbon nanotubes are considered the best material in the field of composites because of their mechanical and tribological properties. In this study, carbon nanotubes coated metal was dispersed in aluminum, the base metal, to improve the wettability between aluminum and carbon nanotubes. The friction and wear behaviors of the aluminum-carbon nanotube coated metal, which is a nickel and copper composite, were investigated using a pin-on-disk wear tester under dry sliding and water lubricated conditions and evaluated using SEM and EDX analysis. All the results demonstrated that the addition of the carbon nanotubes coated metal significantly improved the wettability of CNTs in the aluminum. And the distribution of CNTs prevented the propagation of micro cracks on the surface of the aluminum base metal sample, resulting in enhanced friction characteristics and wear resistance of the nano composite. The composite exhibited lower friction coefficient and wear resistance under the water lubricated condition than the dry sliding condition. Although the lubrication and cooling effect of water contributed to the reduction of the friction coefficient of the composite, the separation of wear particles from the sliding surface changed the wear type from three-body to two-body, resulting in very high wear rate. Also the concentration of oxide under water lubricated condition contributed to the increase of the wear rate because the amount of oxide film removed in terms of thickness exceeded the critical thickness of real contact area.

A comparison of the effects of multi-wall and single-wall carbon nanotube additions on the properties of zirconia toughened alumina composites

The use of multi-wall carbon nanotubes (MWCNTs) or single-wall carbon nanotubes (SWCNTs) as filler in ceramic matrices could create composites with exceptional mechanical properties. We have prepared dense monolithic alumina (Al 2O 3) and zirconia-toughened alumina (ZTA) composites with additions of 0.01 wt% of MWCNTs or 0.01 wt% of SWCNTs by conventional sintering and have demonstrated that the mechanical properties depend on (a) the distribution of CNTs in the matrix and (b) the interaction between the ceramic phases and CNTs. The fracture toughness of Al 2O 3 ceramics reinforced with SWCNTs was significantly better than those reinforced with MWCNTs. However, fracture toughness in MWCNT-reinforced ZTA increased 41% over ZTA free of the toughening agent and 44% over ZTA reinforced with SWCNTs. A well dispersed and small amount of MWCNTs was enough to produce an increase of fracture toughness in ZTA composites.

Optimization of Deposition Conditions for CNTs/Carbon Fiber Hybrid Multiscale Composites via Taguchi Method

Electrophoretic deposition (EPD) technique was applied to deposit carbon nanotubes on a carbon fabric. Optimization of EPD conditions was investigated to improve electrical conductivity for CNTs/carbon fiber hybrid multiscale composites by Taguchi method. Based on design of experiment, a L9(3)4 orthogonal array was chosen to conduct experiments. Due to the electrical conductivity of composites increased with the increasing content of CNTs in composites, it was selected as the response on the analysis of the means (ANOM) and the signal to noise (S/N) ratio. In addition, scanning electron microscopy (SEM) was utilized to examine the distribution of CNTs on the surface of a carbon fabric. The statistical software MINITAB 14 was utilized to determine the optimal deposition conditions.

Effect of carbon nanotubes and their dispersion on thermal curing of polyimide precursors

The process of thermal imidization reaction is significant for temperature and time control in the polyimide industry. Here, we report the effect of carbon nanotubes and their states of dispersion on the thermal imidization of the precursor films of polyimide (poly(amic acid)) for the first time. The curing process was followed by measuring Fourier transform-infrared (FT-IR) spectra, fluorescence spectra, thermogravimetric-differential scanning calorimeter (TG-DSC) properties and the refractive indices of films. It was found that by evenly dispersing 1 wt% of carbon nanotubes assisted by a dispersant in the poly(amic acid),the full imidization temperature of the polyimide can be reduced from 300 °C to 250 °C. Different states of distribution of CNTs were observed by light microscopy and scanning electron microscopy, and proved that a better dispersion of carbon nanotubes dramatically enhanced the speed of imidization. Moreover, the DSC results showed that lower decomposition temperature of poly(amic acid) could be obtained with more uniform distribution of carbon nanotubes, which means the process of cyclodehydration of the poly(amic acid) was accelerated.

Thermal properties of carbon nanotube-copper composites for thermal management applications.

Carbon nanotube–copper (CNT/Cu) composites have been successfully synthesized by means of a novel particles-compositing process followed by spark plasma sintering (SPS) technique. The thermal conductivity of the composites was measured by a laser flash technique and theoretical analyzed using an effective medium approach. The experimental results showed that the thermal conductivity unusually decreased after the incorporation of CNTs. Theoretical analyses revealed that the interfacial thermal resistance between the CNTs and the Cu matrix plays a crucial role in determining the thermal conductivity of bulk composites, and only small interfacial thermal resistance can induce a significant degradation in thermal conductivity for CNT/Cu composites. The influence of sintering condition on the thermal conductivity depended on the combined effects of multiple factors, i.e. porosity, CNTs distribution and CNT kinks or twists. The composites sintered at 600°C for 5 min under 50 MPa showed the maximum thermal conductivity. CNT/Cu composites are considered to be a promising material for thermal management applications.

Microstructural and Mechanical Properties of Titanium Matrix Composites Reinforced with Nano Carbon Materials via Powder Metallurgy Process

Powder metallurgy (P/M) titanium matrix composite (TMC) reinforced with multi-wall carbon nanotube (MWCNT) was prepared by spark plasma sintering (SPS) and hot extrusion process, where the powder surface was coated by un-bundled CNTs via wet process. The microstructure and mechanical properties of P/M pure titanium and reinforced with CNTs were evaluated. The distribution of CNTs and in-situ formed titanium carbide (TiC) compounds during sintering was investigated by optical and scanning electron microscopy (SEM) equipped with EDS analyser. The mechanical properties of TMC were significantly improved by adding a small amount of CNTs. For example, when employing the pure titanium composite powder coated with CNTs of 0.35 mass%, the increase of tensile strength and yield stress of the extruded TMC was 157 MPa and 169 MPa, respectively, compared to those of extruded titanium materials with no CNT additive. Fractured surfaces of specimens were analysed by SEM, and the uniform distribution of CNTs and TiC particles, being effective for the dispersion strengthening, at the surface of the TMC were obviously observed.

Interaction models for effective thermal and electric conductivities of carbon nanotube composites

The present article provides supplementary information of previous works of analytic models for predicting conductivity enhancements of carbon nanotube composites. The models, though fairly simple, are able to take account of the effects of conductivity anisotropy, non-straightness, and aspect ratio of the CNT additives on the conductivity enhancement of the composite and to give predictions agreeing well with existing experimental data. The omitted detailed derivation of this model is demonstrated in the present article with a more systematical analysis, which may help with further development in this direction. Furthermore, the effects of various orientation distributions of CNTs are reported here for the first time. The information may be useful in design or fabrication technology of CNT composites for better or specified conductivities.

Characteristics of powder metallurgy pure titanium matrix composite reinforced with multi-wall carbon nanotubes

By using pure titanium powder coated with un-bundled multi-wall carbon nanotubes (MWCNTs) via wet process, powder metallurgy (P/M) titanium matrix composite (TMC) reinforced with the CNTs was prepared by spark plasma sintering (SPS) and subsequently hot extrusion process. The microstructure and mechanical properties of P/M pure titanium and reinforced with CNTs were evaluated. The distribution of CNTs and in situ formed titanium carbide (TiC) compounds during sintering was investigated by optical and scanning electron microscopy (SEM) equipped with EDS analyzer. The mechanical properties of TMC were significantly improved by the additive of CNTs. For example, when employing the pure titanium composite powder coated with CNTs of 0.35 mass%, the increase of tensile strength and yield stress of the extruded TMC was 157 MPa and 169 MPa, respectively, compared to those of extruded titanium materials with no CNT additive. Fractured surfaces of tensile specimens were analyzed by SEM, and the uniform distribution of CNTs and TiC particles, being effective for the dispersion strengthening, at the surface of the TMC were obviously observed.

Carbon Nanotubes as Highly Conductive Nano-Fillers in Metallic Matrices

. A baseline electroless deposition processes for Cu on CNTs has been developed. This process results in the formation of copper particles of few tens of nanometres. Using this process in a CNT loaded solution it is possible to obtain a homogeneous distribution of CNTs and Cu, even for volume fraction of CNTs as high as 17 v%. By the application of wet chemical processing it is possible to penetrate the natural felt-like structure of the CNTs and to fill the gaps with copper particles. Variations of the baseline deposition process have been established, allowing adding small amount of nickel on the CNT prior to the copper deposition to strengthen the interfacial bonding between matrix and CNTs. Hot pressing of the highly CNT loaded metal matrix composites has been developed; it allows producing bulk material that can be handled. The microstructure of these materials has been investigated and samples have been machined for further testing, i.e. mechanical characterization and thermo-physical properties.

CNTs/TiC Reinforced Titanium Matrix Nanocomposites via Powder Metallurgy and Its Microstructural and Mechanical Properties

By using pure titanium powder coated with unbundled multiwall carbon nanotubes (MWCNTs) via wet process, powder metallurgy (P/M) titanium matrix composite (TMC) reinforced with the CNTs was prepared by spark plasma sintering (SPS) and subsequently hot extrusion process. The microstructure and mechanical properties of P/M pure titanium and reinforced with CNTs were evaluated. The distribution of CNTs and in situ formed titanium carbide (TiC) compounds during sintering was investigated by optical and scanning electron microscopy (SEM) equipped with EDS analyzer. The mechanical properties of TMC were significantly improved by the additive of CNTs. For example, when employing the pure titanium composite powder coated with CNTs of 0.35 mass%, the increase of tensile strength and yield stress of the extruded TMC was 157 MPa and 169 MPa, respectively, compared to those of extruded titanium materials with no CNT additive. Fractured surfaces of tensile specimens were analyzed by SEM, and the uniform distribution of CNTs and TiC particles, being effective for the dispersion strengthening, at the surface of the TMC were obviously observed.

Carbon nanotube-ceramic composites

The effective utilization of CNTs in composite application depends strongly on the ability to disperse CNTs homogeneously throughout the matrix and the interfacial combination is necessary for improving the CNT-based composite properties. In our work, we used surfactant and acid treatment to modify the CNTs surface and then incorporated the functionalized CNTs into various ceramic matrices including oxide and nitride ceramics. The fabrication of ceramic nanoparticle-immobilized CNTs not only improves the homogeneous distribution of CNTs in the ceramic matrices, but also makes the combination between two phases more tight. Mechanical property measurements clealy reveal obvious enhancement confirming the fabrication of true CNT-based composite materials with improved toughness properties. The addition of 0.1 wt% CNTs in the alumina increased the fracture toughness by about 1.6 times from 3.7 to 4.9 MPa.m1/2. For 1 wt% CNTs/BaTiO3composite, the toughness value (1.65 MPa.m1/2) is about 2.4 times than that of pure BaTiO3(0.68 MPa.m1/2). For 5 wt% CNTs/TiN composite, the fracture toughness is 3.81 MPa.m1/2, which is about 1.6 times than that of pure TiN ceramic whose toughness is 2.45 MPa . m1/2.

Improved Field-Emission Properties of Carbon Nanotube Field-Emission Arrays by Controlled Density Growth of Carbon Nanotubes

The density distribution of CNTs is one of the crucial parameters determing the field-emission property of CNTs. To effectively control the density of CNTs, an inactive thin-film layer was deposited on a catalyst. The results showed that improved field emission property could be obtained with a thin SiO layer on the catalyst layer as the precursor. For 3.5 nm Fe and 3.5 nm SiO on 3.5 nm Fe as a catalyst, the turn-on field could be decreased from 3.7 V/µm. to 2.2 V/µm and the field-emission current density increased from 2.6×10-8 A/cm2 to 2.4×10-4 A/cm2 when the applied field was 4 V/µm

Tissue distribution of concentrative and equilibrative nucleoside transporters in male and female rats and mice.

Concentrative nucleoside transporters (Cnts) and equilibrative nucleoside transporters (Ents) have essential physiological functions and are important in disposition of anticancer and antiviral nucleoside analogs. Information on tissue distribution of Cnts and Ents in rodents is sparse. Thus, the present study aimed to determine the distribution of Cnt1-3 and Ent1-3 transcripts in 19 tissues of Sprague-Dawley rats and C57BL/6 mice of both genders. These six transcripts were quantified using the branched DNA signal amplification assay. Cnt1 transcripts were highest in small intestine, followed by kidney and testes, with similar expression in both species. Cnt2 mRNA was expressed highest in the small intestine of both rats and mice, intermediate in liver of rats but not in mice, and lower in thymus and spleen of both species. Cnt3 mRNA has marked species differences, with the highest expression in lung of rats but uterus of mice. Ent1 mRNA was most highly expressed in testes and lung of both species. Ent1 mRNA was highly expressed in liver and pituitary of mice, but not in rats. Ent2 mRNA was highly expressed in testes and brain of both species. Ent3 mRNA was highest in kidney, followed by testes, in both species. Significant gender differences were observed in kidney (mouse) and heart (rat). These studies demonstrate that in general, tissue distribution of Cnt and Ent is similar in rats and mice. However, a few important species and gender differences do exist, which could be responsible for related differences in efficacy and toxicity of substrates for these transporters.

Characterization of Carbon Nanotubes/Cu Nanocomposites Processed by Using Nano-sized Cu Powders

AbstractCarbon nanotubes (CNTs) have attracted remarkable attention as reinforcement for composites owing to their outstanding properties1-3. CNT/Cu nanocomposites were fabricated by mixing the nano-sized Cu powders with multi-wall carbon nanotubes and followed by the spark plasma sintering process. The CNT/Cu nanocomposite fabricated from nano-sized Cu powders shows more homogeneous distribution of CNTs in matrix compared to that fabricated from macro-sized Cu powders. The hardness of CNT/Cu nanocomposite fabricated from nano-sized Cu powders increases with increasing the volume fraction of CNTs, while the hardness of that fabricated from macro-sized Cu powders decreases with the addition of CNTs.