Liquid Chromatography Detection Research Articles

Early Diagnosis of Tumorigenesis via Ratiometric Carbon Dots with Deep-Red Emissive Fluorescence Based on NAD+ Dependence

The early diagnosis of tumorigenesis is crucial for clinical treatment, but the resolution and sensitivity of conventional short-wavelength biomarkers are not ideal because of the complicated interference in living tissue. Herein, a nicotinamide adenine dinucleotide (NAD+)-responsive probe with deep-red emissive ratiometric fluorescence was synthetized as a promising target for energy metabolism patterns during tumorigenesis. Interestingly, the solvents H3PO4 and 2,2′-dithiodibenzoic acid enhanced the red emission (640 and 680 nm) of o-phenylenediamine-based carbon dots (CDs), leading to the formation of a nanoscale graphite-like skeleton covered with -P=O, -CONH-, -COOH and -NH2 on their surfaces. Meanwhile, this method exhibited high sensitivity to the discriminating target NAD+, with a detection limit of 63 μM due to the inner filter effect and fluorescence resonance energy transfer process between NAD+ and CDs, which is superior to the reported capillary electrophoresis and liquid chromatographic detection methods (the reported detection limit was about 0.2 mM) in complex biological samples and even cancer cells. Encouragingly, NAD+ significantly promoted nucleus-targeting fluorescence and cell migration compared to GSH and pH stimulation, which were gradually eliminated in human hepatocellular carcinoma (HepG2) cells after 2-deoxy-d-Glucose inhibited the glycolytic phenotype. The proposed method holds great potential for the temporal and spatial resolution of NAD+-dependent tumor diagnosis in complex living systems.

Development of a 3D Printed Chemiluminescence Smartphone Detector for High Performance Liquid Chromatography

A novel chemiluminescence detector for high-performance liquid chromatography (HPLC) was designed that incorporates a smartphone as photodetector, signal processor, and data storage unit. All detector components, including flow cell, flow cell holder, mixers, and housing, were fabricated by 3D printing and integration of the smartphone and 3D printed components provides a portable, low-cost, and user-friendly device. The detector was applied in the determination of carbamazepine using HPLC through a chemiluminescence reaction with tris(2,2′-bipyridyl)ruthenium(II) and cerium sulfate. Design and fabrication of the flow cell using two fabrication methods—3D printing and laser cutting—along with the integration of a mixer and the optimization of smartphone parameters were investigated. To expand the applicability of the detector for other analytes and different chemiluminescence reactions, detection of three piperazine derivatives by reaction with tris(2,2′-bipyridyl)ruthenium(II) and four phenethylamine compounds via reaction with acidic potassium permanganate reagent was studied. The linear dynamic range, limit of detection, and limit of quantification of the detector for the determination of carbamazepine were measured as 3.0–30.0 mg/L, 1.0 mg/L, and 3.0 mg/L, respectively, using the Samsung S20 smartphone device. Intraday and interday precision was evaluated for carbamazepine, with relative standard deviation (RSD) values for intraday precision ranging from 1.7% to 6.2% (n = 3) and interday precision RSD values ranging from 3.2% to 4.8% (n = 9).

Simultaneous extraction and deglycosylation for flavonoid analysis in Ginkgo biloba products using a two-phase deep eutectic solvent system

Total flavonoid content is one of the most important quality indicators of Ginkgo biloba leaves and its products, but the complex pretreatment procedures and the excessive use of organic solvents complicate the detection process. In response, an innovative and efficient two-phase deep eutectic solvent (DES) system—composed of an acidic hydrophilic DES and a hydrophobic DES—was developed to quantify flavonoids for quality control of G. biloba products. High-performance liquid chromatography (HPLC) detection conditions were optimized, followed by systematic screening and design of the two-phase DES system through adjustments to polarity, hydrophilicity, and acidity. Optimal pretreatment conditions were established through operating condition optimization. This approach enabled simultaneous extraction, deglycosylation, and enrichment of all flavonoids from G. biloba samples into the hydrophobic phase in a single step. Method validation showed strong linearity with a correlation coefficient (R2 > 0.9995). The detection (LOD) and quantification (LOQ) limits were between 0.35 and 0.37 mg/kg, and 0.92 and 0.96 mg/kg, respectively. The method also exhibited high sensitivity and accuracy, with a recovery rate of 96.91–100.39%. A greenness assessment with the ComplexGAPI tool confirmed this method’s eco-friendly advantages over conventional techniques, aligning well with green chemistry and economic principles. Ultimately, this technique effectively measured flavonoid levels in different G. biloba products. The method developed in this work not only enhances the efficiency of simultaneous extraction and deglycosylation by modifying the polarity, hydrophilicity, and acidity of the two-phase DES system, but also offers valuable insights for the advancement of environmentally friendly analysis technology for flavonoids.

Role of the Power Function Value in Linearity and Universality for Charged Aerosol Detectors: Theoretical Elucidations from a Validated Model.

High-throughput drug discovery on the microgram scale is now common, making analyte quantitation without molecule-specific calibration imperative. The charged aerosol detector (CAD) was invented to be a next-generation universal liquid chromatography (LC) detector with excellent response universality for nonvolatile analytes as well as sensitivity for nonchromophoric compounds. Although the CAD is a mass flow-sensitive detector, its response to mass is inherently nonlinear, which challenges traditional quantitation. In CAD software, there is a "power function value" (p) setting that can be used to linearize the signal through digital signal processing. The exact workings of this power function value algorithm remain unknown; however, its optimization is a crucial aspect of analytical method development for LC-CAD. Herein, we developed a theoretical relationship that can be used to predict the chromatogram (plus peak area, width, and height) at any p if the data are collected at p = 1. This model was validated using a diverse dataset comprising 1440 measurements including peak heights, areas, and widths. Predicted areas had an average error of less than 2% showing excellent agreement between calculated and experimental results. An open-access automated code is tested and provided, which predicts the power function value that produces the most linear response. It is vital to note that optimizing the power function value affects peaks of different heights disproportionately. Low-level impurities were shown to be minimized and eventually eliminated by increasing the power function value. This model provides an easy-to-implement tool (MATLAB or Excel) that assists in choosing the optimal p for each LC-CAD method, increasing the speed of method development and improving the accuracy of quantitative workflows.

Elastin-like polypeptide-functionalized nanobody for column-free immunoaffinity purification of aflatoxin B1.

A column-free immunoaffinity purification (CFIP) technique for sample preparation of aflatoxin B1 (AFB1) was developed using an AFB1-specific nanobody (named G8) and an elastin-like polypeptide (ELP). The reversible phase transition between liquid and solid in response to temperature changes was exhibited by the ELP which was derived from human elastin. The G8 was tagged with ELPs of various lengths (20, 40, 60, and 80 repeat units) at the C-terminus using recursive directional ligation (RDL). Coding sequences were then subcloned into pET30a at the multiple cloning sites. Bioactive recombinant proteins were produced by expressing them as inclusion bodies in Escherichia coli BL21 (DE3), then dissolved and refolded. Analysis by indirect competitive enzyme-linked immunosorbent assay (icELISA) and transition temperature (Tt) measurement confirmed that the refolded G8-ELPs preserved the ability to recognize AFB1 as well as phase transition when the temperature rose above Tt. To establish the optimal conditions for cleaning AFB1, the effects of various parameters on recovery were investigated. The recovery in ELISA tests was 95 ± 3.67% under the optimized CFIP workflow. Furthermore, the CFIP-prepared samples were applied for high-performance liquid chromatography (HPLC) detection. The recovery in the CFIP-HPLC test ranged from 54 ± 1.86% to 98 ± 3.58% for maize, rice, soy sauce, and vegetable oil samples. To the best of our knowledge, this is the first report combining the function of both nanobody and ELP to develop a cleanup technique for small molecules in a complex matrix. The CFIP for the sample pretreatment was easy to use and inexpensive. In contrast to conventional immunosensitivity materials, the reagent utilized in the CFIP was entirely biosynthesized without any chemical coupling reactions. This suggests that the nanobody-ELP may serve as a useful dual-functional reagent for the development of sample cleaning or purification methods.

Fusarium andiyazi, a Pathogenic Species Associated with Rice Bakanae Disease in Malaysia.

Rice is the main staple food crops for the Malaysian population. Rice is also susceptible to bakanae diseases caused by some Fusarium species and reducing yield, and quality of rice also profit. In this study, several rice fields were surveyed to collect Fusarium isolates associated with bakanae disease. The morphological features of Fusarium andiyazi isolates found on infected rice plants were identified in this investigation. For biological species identification, MAT-1 (Mating type idiomorphs) bearing isolates were crossed with MAT-2 isolates. Crossing was succeeded between cross of two different mating type bearing field isolates. Consequently, there is a possibility of exchange of genetic material within the F. andiyazi population in Malaysia. The identity of the isolates was further determined up to the species level by comparing DNA sequences and phylogenetic analysis of two genes. The phylogenetic analyses of the joined dataset of translation elongation factor 1-alpha (TEF1-α) and RNA polymerase subunit II (RPB2) revealed that all the isolates were F. andiyazi. In pathogenicity tests, F. andiyazi were found to be pathogenic on the susceptible rice cultivars MR211 and MR220. Inoculated rice seedling produced typical bakanae symptom like elongation, thin and yellow leaves. F. andiyazi was further confirmed as pathogenic species by Ultra High-Performance Liquid Chromatography (UPLC) detection of Gibberellic acid (GA3) and Fusaric acid. In this study, F. andiyazi strains have been identified as the responsible pathogen for causing rice bakanae disease in Malaysia and it is the first report of F. andiyazi, as a pathogenic species on rice in Malaysia.

Construction of magnetic recoverable porous electron-rich organic frameworks for efficiently enrichment of phenylurea herbicides from water and milk samples prior to HPLC detection

Porous electron-rich organic frameworks have attracted an increased attention in the adsorption and removal of pollutants due to their abundant electron-rich nitrogen atoms, which can effectively interact with positively charged substance. In this study, a porous electron-rich organic framework (Car-POF) and positively charged amino-functionalized magnetic nanoparticles (Fe3O4-NH2) were used to construct a magnetic electron-rich Fe3O4-NH2@Car-POF for the enrichment of some phenylurea herbicides from water and milk samples prior to high performance liquid chromatographic detection. The adsorption capacity of Fe3O4-NH2@Car-POF for the phenylureas ranged from 14.93 to 28.83 mg g−1. The LODs were observed in the range of 0.05–0.20 ng mL−1 and 0.5–1.5 ng mL−1, and LOQs in the range of 0.17–0.66 ng mL−1 and 1.7–5.0 ng mL−1 for water and milk samples with RSD less than 9.0. The adsorption studies with cationic and anionic dyes revealed that Fe3O4-NH2@Car-POF is favorable for the adsorption of positively charged compounds.

A nitrogen-specific detector for high performance liquid chromatography

We describe a nitrogen-specific detector (NSD) for aqueous mobile phase-based high performance liquid chromatography (HPLC). It is based by means of total hydrophilic organic nitrogen detection. Separated analytes are photooxidized online and converted to nitrate, followed by an ultravilet absorbance detector. It features response dependant on the product of nitrogen number in the molecule and its molar concentration, no matter what is ultravilet-absorbing or not. The HPLC equipped with NSD can quantify nitrogen-containing analytes via a sole standard of potassium nitrate for calibration. This results in identical calibration curve for all nitrogen-containing analytes, obviating individual calibration. The limit of detection of NSD is 4.3 μM N/L, and its linear range is up to 4 mM N/L.

Fabrication of sea urchin shaped polyaniline-modified magnetic microporous organic network for efficient extraction of non-steroidal anti-inflammatory drugs from animal-derived food samples

In this work, a novel polyaniline-modified magnetic microporous organic network (MMON-PANI) composite was fabricated for effective magnetic solid phase extraction (MSPE) of five typical nonsteroidal anti-inflammatory drugs (NSAIDs) from animal-derived food samples before high performance liquid chromatography (HPLC) detection. The core-shell sea urchin shaped MMON-PANI integrates the merits of Fe3O4, MON, and PANI, exhibiting large specific surface area, rapid magnetic responsiveness, good stability, and multiple binding sites to NSAIDs. Convenient and effective extraction of trace NSAIDs from chicken, beef and pork samples is realized on MMON-PANI via the synergetic π-π, hydrogen bonding, hydrophobic, and electrostatic interactions. Under optimal conditions, the MMON-PANI-MSPE-HPLC-UV method exhibits wide linear ranges (0.2–1000 μg L−1), low limits of detection (0.07–1.7 μg L−1), good precisions (intraday and inter-day RSDs < 5.4 %, n = 3), large enrichment factors (98.6–99.9), and less adsorbent consumption (3 mg). The extraction mechanism and selectivity of MMON-PANI are also evaluated in detail. This work proves the incorporation of PANI onto MMON is an efficient way to promote NSAIDs enrichment and provides a new strategy to synthesize multifunctional MON-based composites in sample pretreatment.

A novel ultra-performance liquid chromatography detection method development and validation for paclitaxel and its major metabolite in human plasma.

Paclitaxel is a promising anticancer drug for patients with ovarian, breast, lung, gastrointestinal, genitourinary, prostate, and head-and-neck cancers. Paclitaxel follows nonlinear pharmacokinetics. The major metabolite of paclitaxel is 6-alpha-hydroxy paclitaxel, mediated by CYP2C8, while metabolism to two of its minor metabolites, 3'-p-hydroxypaclitaxel and 6a, 3'- p-dihydroxypaclitaxel, is catalyzed by CYP3A4. Therapeutic drug monitoring of paclitaxel could be a promising approach to improve the efficacy and safety of paclitaxel correct personalized doses and improve the overall benefit-risk ratio. A novel and highly sensitive chromatographic method for the detection of paclitaxel and its metabolite has been proposed that allows quantification in human plasma with 100% accuracy in terms of recovery without significant intraday or interday variations. The present study was planned following bioanalytical method validation guidance according to the U.S. Food and Drug Administration requirements. The validation of the analytical procedure was performed as per ICH Q2(R1) guidelines. It was done to assure the reliability of the results obtained for various parameters such as linearity, accuracy, precision, limit of detection (LOD), limit of quantification, robustness, stability, and system suitability. The specificity of the method was established by ensuring no interference with peak obtained from paclitaxel and 6-alpha-hydroxy paclitaxel. LOD was found to be 0.05 and 0.033 while the limit of quantitation was 0.14 and 0.099 for paclitaxel and 6-alpha-hydroxy paclitaxel, respectively. Median (±interquartile range) accuracy for paclitaxel and 6-alpha-hydroxy paclitaxel was found to be 102.73 (±13.581) and 100.87 (±7.573), respectively. This novel method of simultaneous detection of paclitaxel and its major metabolite 6-alpha-hydroxy paclitaxel demonstrated significant resolution and was sensitive enough for its quantification in human plasma.

METHOD VALIDATION FOR DETERMINATION OF KYNURENIC ACID CONTENT IN NATURAL PRODUCTS BY RP-HPLC-UV

Kynurenic acid (KYNA) is a metabolite with pharmacoactive properties found primarily in chestnut honey, linden, and other honeys. Considering the anti-inflammatory and immunosuppressive functions of KYNA, it can be seen that it has bidirectional effects on biological pathways. For this reason, determining and knowing the amount of honey, an important natural product can have a high impact on health. Studies on the detection of this metabolite in both natural products and animal tissues are ongoing, and it is important to develop fast and easily applicable methods. Within the scope of this study, a new method was created using an ultraviolet detector (RP-HPLC-UV) in reverse-phase high-performance liquid chromatography to determine the KYNA content of natural products (honey, chestnut pollen, and chestnut flowers) quantitatively in a short time. According to the data obtained, LOD and LOQ values were found to be 0.030 µg/mL and 0.092 µg/mL, respectively. At the same time, solutions of KYNA prepared in ultrapure water (UPW), 70% EtOH, EtOH and MeOH solvents were analyzed in this method, and it was found that UPW was the best solvent. The findings of this research can contribute significantly, particularly in the application of measuring KYNA, to distinguishing the botanical origin of chestnut honey.

CdTe@ZnS quantum dots for rapid detection of organophosphorus pesticide in agricultural products

Organophosphorus pesticides (OPPs) constitute the most widely employed class of pesticides. However, the prevalent use of OPPs, while advantageous, raises concerns due to their toxicity, posing serious threats to food safety. Chemical sensors utilizing quantum dots (QDs) demonstrate promising applications in rapidly detecting OPPs residues, thereby facilitating efficient inspection of agricultural products. In this study, we employ an aqueous synthesis approach to prepare low toxic CdTe@ZnS QDs with stable fluorescence properties. To mitigate the risk of imprecise measurements stemming from the inherent susceptibility of fluorescence to quenching, we have adopted the principle of fluorescence resonance energy transfer (FRET) for the construction of the turn-on quantum dot sensor. With a detection limit for chlorpyrifos as low as 10 ppb (10 μg/L), the QDs sensor exhibits notable resistance to interference from various pesticides. Application of this system to detect organophosphorothioate pesticides in apples produced results consistent with those obtained from high-performance liquid chromatography (HPLC) detection, affirming the promising application prospects of this sensing system for the rapid detection of OPPs residues.

A Review on Extraction and Chromatographic Techniques for Organophosphate Pesticidal Residue Analysis in Paddy and Rice Bran

Organophosphorus pesticides (OPPS) are extensively employed in agricultural techniques and may expose people to them via food intake. We offer an analytical approach for detecting OPPS in paddy, rice grains and or rice bran that combines solid-phase extraction with a high-performance liquid chromatography detector. Acetonitrile extraction was used before SPE–HPLC–MSMS to isolate specific residues, which helped decrease matrix disruptions and identify a broad array of numerous residues in rice grains. Accordingly, ranges of quantitative determination ranged from 0.01mg/kg to more than 1.0 mg/kg, with coefficients extending from 0.995 to more than 0.999. At three stimulating intensities, high recuperation was reported, suggesting excellent precision. The relative SD of all residues confirmed the technique’s accuracy. Using this, various OPPS were quantified, ranging from just below to maximum permissible limits to exceeding the limit. According to a sample study of different rice grain varieties accessible in the international market. This study focuses on the techniques of organophosphate pesticide residue extraction from paddy and rice ban. The study further discusses chromatographic techniques for the same.

Split-ring resonator with interdigital Split electrodes as detector for liquid and ion chromatography

The analysis of food and drugs as well as the monitoring of chemical processes and bioreactors by high-performance liquid chromatography and ion chromatography requires universal, cost-effective, and sensitive detectors. Therefore, this work presents a split-ring resonator that detects changes in the electrical and dielectric properties of the eluate from liquid chromatography or ion chromatography by monitoring the amplitude of the transmitted signal using an envelope detector. The used split-ring resonator consists of a simple printed circuit board featuring two microstrip lines. One is formed to a ring with interdigital split electrodes. The interdigital split electrodes forming the sensitive area significantly enhance the sensitivity to changes in relative permittivity, dielectric losses and electrical conductivity of the eluate In addition, the split-ring resonator is a small, inexpensive and easy-to-use detector that uses several dielectric parameters simultaneously for the measurement. Furthermore, the split-ring resonator measures these parameters at a significantly lower frequency than optical detectors and therefore measures different changes in frequency-dependent permittivity. For demonstrating feasibility of a split-ring resonator as a detector for high-performance liquid chromatography and ion chromatography, various anion and cation standards, basic and acidic amino acids, sugars, as well as sugar alcohols were separated and detected. A conductivity detector for ion chromatography and a refractive index detector for high-performance liquid chromatography were used as reference detectors.

Comparison of Different Grades of Innovative Tanyang Congou Black Tea (Minkehong) Based on Metabolomics and Sensory Evaluation

Innovative Tangyang Congou black tea, also known as Minkehong black tea (MKH), is of high quality and hence has gained a reputation on the market. In this study, standard samples of MKH were used as the research material, and the results of sensory evaluation showed that the overall quality of MKH decreased along with the downgrading. The radar chart showed a strong association between higher grades and specific aroma and taste character. Based on the detection of ultra-performance liquid chromatography–mass spectrometry (UPLC–MS) and related analysis, the content of both the ester-type catechins and non-ester catechins decreased along with the downgrading, and the details of their change trends were revealed. The content and dynamic changes in caffeine were also investigated. A total of 19 kinds of amino acids (AAs) were clustered; among them, 4 kinds of AAs, namely, Thr, Leu, Asp, and Ile, significantly contributed to the taste of the tea. Notably, the content of Thr had the highest correlation with the grade of MKH, and the correlation coefficient was 0.991 (p &lt; 0.01). According to gas chromatography–mass spectrometry (GC–MS) detection and analysis, a total of 861 kinds of volatile compounds were detected, the aroma-active compounds in different grades were selected, and an aroma wheel of MKH was constructed. Our results found that non-volatile and volatile compounds not only contribute to defining the level of MKH standard samples but also provide a chemical basis for the measurement of flavour and quality of MKH.

Methodology for high-performance liquid chromatography detection of latanoprost and latanoprost free acid

AbstractA gradient high-performance liquid chromatography (HPLC) method has been developed to determine the concentrations of latanoprost (LP) and latanoprost free acid (LPA) in aqueous solutions. It is novel due to a combination of its simplicity, speed, and detection capability in aqueous solutions for both active drug (LPA) and prodrug (LP). This method is applicable for the research and development of novel drug delivery devices and quality control assays for experimental and commercial laboratory settings, as it allows for a high sample throughput. Samples were chromatographed across a C18 + 2.7 µm 4.6 × 7.5 mm reversed-phase column with gradient elution using a mobile phase of aqueous acetic acid (pH 3.1) and acetonitrile with 0.1% acetic acid. UV spectrophotometry was used to monitor the eluents at 210 nm. Drug concentrations from 1.0 to 150 μg mL−1 were tested, with good linearity observed across the range. LPA had a signature peak at approximately 4.82 min (SD &lt; 0.08) and LP at 9.27 min (SD &lt; 0.07). For both drug and pro-drug, LOD and LOQ were 1.0 and 2.5 μg mL−1, respectively. This assay which accurately measures both prodrug and drug in a single injection, has significant applicability in determining the release kinetics of novel LP drug delivery systems.

Transcriptome and comparative chloroplast genome analysis of Taxus yunnanensis individuals with high and low paclitaxel yield

Paclitaxel is a potent anti-cancer drug that is mainly produced through semi-synthesis, which still requires plant materials as precursors. The content of paclitaxel and 10-deacetyl baccatin III (10-DAB) in Taxus yunnanensis has been found to differ from that of other Taxus species, but there is little research on the mechanism underlying the variation in paclitaxel content in T. yunnanensis of different provenances. In this experiment, the contents of taxoids and precursors in twigs between a high paclitaxel-yielding individual (TG) and a low paclitaxel-yielding individual (TD) of T. yunnanensis were compared, and comparative analyses of transcriptomes as well as chloroplast genomes were performed. High-performance liquid chromatography (HPLC) detection showed that 10-DAB and baccatin III contents in TG were 18 and 47 times those in TD, respectively. Transcriptomic analysis results indicated that genes encoding key enzymes in the paclitaxel biosynthesis pathway, such as taxane 10-β-hydroxylase (T10βH), 10-deacetylbaccatin III 10-O-acetyltransferase (DBAT), and debenzoyl paclitaxel N-benzoyl transferase (DBTNBT), exhibited higher expression levels in TG. Additionally, qRT-PCR showed that the relative expression level of T10βH and DBAT in TG were 29 and 13 times those in TD, respectively. In addition, six putative transcription factors were identified that may be involved in paclitaxel biosynthesis from transcriptome data. Comparative analysis of plastid genomes showed that the TD chloroplast contained a duplicate of rps12, leading to a longer plastid genome length in TD relative to TG. Fifteen mutation hotspot regions were identified between the two plastid genomes that can serve as candidate DNA barcodes for identifying high-paclitaxel-yield individuals. This experiment provides insight into the difference in paclitaxel accumulation among different provenances of T. yunnanensis individuals.

Silver nanoparticle-functionalized melamine-formaldehyde aerogel for online in-tube solid-phase microextraction of polycyclic aromatic hydrocarbons followed by HPLC-DAD analysis

Based on the π-metal interaction between silver nanoparticles (AgNPs) and aromatic compounds, AgNPs were in-situ grown to melamine-formaldehyde (MF) aerogel for improving the extraction performance to polycyclic aromatic hydrocarbons (PAHs). The AgNPs/MF aerogel was regulated through varing the concentration of reactants, and characterized by scanning electron microscopy, X-ray photoelectron spectroscopy and X-ray powder diffraction. As a new extraction coating, the AgNPs/MF aerogel was coated to stainless-steel wires for in-tube solid-phase microextraction (IT-SPME). The extraction effects of MF aerogels before and after the modification of AgNPs were compared, and the AgNPs greatly improved the extraction ability for PAHs reaching to 166.4 %. Combining IT-SPME with high performance liquid chromatographic detection, an online analytical system was constructed. Furthermore, the sampling volume and rate, concentration of organic solvent, and desorption time were optimized factor by factor. The online analytical method with low detection limits (0.003–0.010 μg L−1) and efficient enrichment factors (1998–3237) for PAHs was established, which fastly detected trace level of PAHs in drinking and environmental water samples. Compared with other methods, the method was comparable or better in the detection limit and linear range, indicating prospective application of the AgNPs/MF aerogel for sample preparation.

Amperometric Inkjet-Printed Thyroxine Sensor Based on Customized Graphene and Tunned Cyclodextrins as the Preconcentration Element.

The determination of thyroid hormones has practical clinical significance for the diagnosis of hyperthyroidism and hypothyroidism diseases. Considering this aspect, a wide range of analytical methods for the detection of analytes, including immunoassay, chemiluminescence, mass spectroscopy and high-performance liquid chromatography, among others, has been developed. This type of analysis provides feasible results. Nevertheless, it requires qualified staff, special facilities and is time-consuming. For this reason, this paper relies on the fabrication of an electrochemical device developed with inkjet printing technology for the free detection of Thyroxine (T4). To manufacture our electrochemical device, several aspects were considered from the use of materials that amplify electrical signals, to finding a supramolecular scaffold that possess affinity towards the target analyte and the need of preconcentrating the analyte on the electrode's surface. For this task, printed devices were modified with a hybrid nanomaterial consisting of reduced graphene oxide (rGO) tuned with Au nanoparticles (Au-NPs) and an entrapment agent and different thiolated cyclodextrins (x-CD-SH) as carrying agents. Analytes were preconcentrated via supramolecular chemistry due to the formation of an inclusion complex between the cyclodextrin and hormones. Morphological and electrochemical characterization of the final device was carried out to ensure the proper workability of the electrode, achieving excellent response, sensitivity and limit of detection (LOD).

Determination of Aflatoxin B1 in Grains by Aptamer Affinity Column Enrichment and Purification Coupled with High Performance Liquid Chromatography Detection.

Aflatoxin B1 (AFB1) is a highly teratogenic and carcinogenic secondary metabolite produced by Aspergillus. It is commonly detected in agricultural products such as cereals, peanuts, corn, and feed. Grains have a complex composition. These complex components severely interfere with the effective extraction and separation of AFB1, and also cause problems such as matrix interference and instrument damage, thus posing a great challenge in the accurate analysis of AFB1. In this study, an aptamer affinity column for AFB1 analysis (AFB1-AAC) was prepared for the enrichment and purification of AFB1 from grain samples. AFB1-AAC with an AFB1-specific aptamer as the recognition element exhibited high affinity and specificity for AFB1. Grain samples were enriched and purified by AFB1-AAC, and subsequently analyzed by high performance liquid chromatography with post-column photochemical derivatization-fluorescence detection (HPLC-PCD-FLD). The average recoveries of AFB1 ranged from 88.7% to 99.1%, with relative standard deviations (RSDs) of 1.4-5.6% (n = 3) at the spiked levels of 5.0-20.0 μg kg-1. The limit of detection (LOD) for AFB1 (0.02 μg kg-1) was much below the maximum residue limits (MRLs) for AFB1. This novel method can be applied to the determination of AFB1 residues in peanut, corn, and rice.