High Voltage DC Power Supply Research Articles

Design of high voltage power supply for SINEW mask

Abstract. Electrostatic Precipitation (ESP) is an effective method of removing particulates from the air. It is currently used in many large-scale industrial applications but sees little to no use in smaller-scale use-cases due to the difficulty of generating high voltage in small packages and safety concerns. This paper presents the motivation, design, and evaluation of a miniature DC high voltage (HVDC) power supply for application in small-scale ESP systems. The power supply's potential for portable ESP application is tested on The Smart, Individualized, Noncontact, Extended-Wear (SINEW) mask. The results show that the power supply operates with acceptable efficiency and generates the necessary high voltages and power necessary to drive ESP even on non-optimized geometries.

Magnetron sputtering thruster operated with a compact gas feeding system using double pulsed valves

A continuous injection of gaseous water propellant into a magnetron-type sputtering propulsion device is performed in a pseudo manner by using a combination of two high-speed solenoid-type pulsed valves and a low-pressure gas reservoir . The gas injection system provides a temporally averaged gas flow rate of about 5–10 sccm with adjustment of the repetition frequencies of the pulsed valves, while the previously used single valve system attached to a liquid water tank has caused excessive gas injection. A discharge is sustained by a high voltage dc power supply; the discharge current has pulsation synchronized with the pulsed valve repetition. A temporally averaged force induced by the magnetron sputtering thruster and exerted on a pendulum plate downstream of the thruster is measured; the results are in good agreement with the previously reported force measurement under precisely controlled gas flow rate using a commercial mass flow controller. Therefore, the precise control of the gaseous water propellant with the compact gas feeding system is achieved, while maintaining a similar thruster performance to that with the mass flow controller.

10 kV high-voltage DC power supply design with novel sliding-mode phase-shift controller for intense field dielectrics

10 kV high-voltage DC power supply design with novel sliding-mode phase-shift controller for intense field dielectrics

Accurate low-energy pulse system for intravascular lithotripsy

In response to biomedical imperatives, a novel approach is presented for the endovascular management of atherosclerosis. This approach is grounded in the electrohydraulic effect of a precisely controlled low-energy pulse discharge system, coupled with sequential control within the incomplete discharge electrode, to generate shockwaves aimed at softening blood vessels and rupturing calcified plaques. Theoretical analysis encompassed circuit design, control timing, and operational processes, while experimental investigations demonstrated precise control of non-oscillation and incomplete discharge by adjusting key parameters. Utilizing a 3 kV DC high-voltage power supply, a 220 nF capacitor, and two sets of 3.3 Ω resistors in parallel, with pin–plate electrodes as the load for discharge in normal saline, resulted in a 1 kV reduction in voltage across the capacitor and a peak current of 170 A. Energy release occurred through non-oscillatory and incomplete discharge, effectively generating shockwaves with peak pressures of 5–10 MPa at distances of 1–2 mm from the discharge center to treat calcified lesions. Compared with the existing intravascular lithotripsy devices, the shockwave system realizes accurate control of discharge energy by adjusting the turn-off time of incomplete discharge so as to realize accurate control of shockwave energy. Doctors can choose different intensities of shockwaves according to different degrees of calcification in the treatment process so as to minimize the discomfort caused by shockwaves and improve safety. Valuable insights are provided for intravascular lithotripsy devices in engineering.

Effect of Metal Oxide Semiconductor Field-Effect Transistor Output Parasitic Capacitance on Efficiency in Full-Bridge LLC DC/DC Converters.

This study analyzed the efficiency impact of a MOSFET output parasitic capacitance (Coss) on a full-bridge LLC DC/DC converter. The core of the converter was the control chip for a half-bridge LLC DC/DC converter, and the output signal of the chip controlled the first-arm power transistors of the primary side of the converter. The coupling transformer reversed the output signal to control the primary side of the second arm of the power transistor. The full-bridge converter comprises a half-bridge control chip that converts the high-voltage DC power supply to a low-voltage DC power supply, which is then synchronously rectified and supplied to the load. The primary side of the power transistor achieves a zero-voltage switching (ZVS) state through the resonance of the LLC converter. This design gives the converter high power density and a simple structure. Furthermore, to determine the appropriate output parasitic capacitance for improving converter efficiency, this study analyzed the effect of the output parasitic capacitance on the switching loss and conduction loss of the power transistor on the basis of the output parasitic capacitance of the primary-side power transistor. A 1200 W converter prototype was fabricated in this study, and when the output was 300 W, efficiency increased from 92.603% to 93.462%, a 0.859% increase. The empirical results verified the feasibility of the proposed theory.

High Voltage and High Frequency DC Power Supply with Ultra High Voltage SiC Schottky Barrier Diode Modules

High Voltage and High Frequency DC Power Supply with Ultra High Voltage SiC Schottky Barrier Diode Modules

Application of high-voltage DC power supply in data center computer room

Application of high-voltage DC power supply in data center computer room

Erratum: Development of high voltage DC power supplies for electrostatic precipitator

Erratum: Development of high voltage DC power supplies for electrostatic precipitator

Study on the Formation and Controllable Movement of Polymer Liquid Columns Based on Dynamic Control of Spatial Electric Field Distribution.

Liquid deformation and motion are very common natural phenomena and of great value in various practical applications. In this study, a dielectric fluid column formation and directional flow phenomenon are presented. Dielectric fluid can grow upward to form a liquid column through a spatial electric field and realize directional and controllable operation of the liquid column by regulating spatial electric field distribution. First, the adjustable electric field space is constructed by connecting the two parallel electrodes to the high-voltage DC power supply. Then, the regional electric field distribution was adjusted by the upper plate graphic and power supply regulation to drive the polymer liquid on the lower plate electrode to form a liquid column at different positions. The results show that the polymer liquid column can be driven by the spatial electric field distributed dynamic control method and that the height and the narrowest width of the liquid column are directly controlled by the voltage. With the experiment conditions that the distance between two parallel electrodes is 5-15 mm, the formation of liquid columns with a height of 5-15 mm can be controlled. In addition, the liquid column can be driven by adjusting the on-states of different conductive regions. When the voltage is 10 kV, the liquid column directional movement speed can reach 1 mm/s. The higher the voltage, the faster the directional movement. The research results can be used as producing polydimethylsiloxane stamp, localized heating and temperature control, fabricating a pulsating heat pipe, and so on.

A Novel Microwave Noise Generator Using Multiple Zener Diodes Connected in Series

A novel microwave noise generator circuit using multiple Zener diodes connected in series was designed and tested. Measurements are presented up to 6 GHz. It is presented in this letter that when the number of series Zener diodes increases, the amount of noise power generated also increases across the band of interest. However, the increase of noise power from one-zener to two-zener configuration and from two-zener to three-zener configuration is not uniform. Measurements were limited to three zeners connected in series due to available high-voltage dc power supply.

Determination of Metals by Portable Millisecond Pulsed Solution Cathode Glow Discharge (SCGD) Atomic Emission Spectroscopy (AES)

In order to determine metal ions in aqueous solution, a millisecond pulsed solution cathode glow discharge (SCGD) source coupled with a portable spectrometer was developed for atomic emission spectrometry (AES). The millisecond pulsed SCGD source was operated with two high-voltage DC power supplies and a high-voltage pulse switch, specifically boosting the analyte excitation and sustain the glow discharge. The method to excite the plasma discharge contrasts with traditional approaches that employ a single power source. The influence of operating parameters, including pulsed voltage, pulsed frequency, duty ratio, and sample flow rate, were optimized to construct a system having good stability and improved excitation of metal ions. The optimum detection limits for Na, K, Li, Mg, Ag, Cs, Rb, and Sr were 0.17, 0.32, 0.38, 0.50, 2.65, 1.30, 0.22, and 74.02 µg·L−1, respectively. Furthermore, mountain spring, Yangtze River, and reservoir water were spiked with Ag, Rb, and Cs; the recoveries ranged from 105% to 106%, 106% to 107%, and 107% to 108% indicating that the developed system has favorable analytical performance.

Development of high voltage DC power supplies for electrostatic precipitator

Development of high voltage DC power supplies for electrostatic precipitator

High Voltage DC Power Supply With Input Parallel and Output Series Connected DC-DC Converters

High Voltage DC Power Supply With Input Parallel and Output Series Connected DC-DC Converters

Sensitive riboflavin sensing using silver nanoparticles deposited onto screen-printed electrodes via controlled-energy spark discharges

In this work, we elaborated the graphite screen-printed electrodes (SPEs) modification with metal nanoparticles formed as a result of spark discharges produced between a metal wire electrode and SPE that are connected to an Arduino board-based DC high voltage power supply. This sparking device allows, on the one hand, the toposelective formation of NPs of controlled dimensions through a direct and liquid-free approach, and on the other hand, controls the number and energy of the discharges delivered to the electrode surface during a single spark event. This way, the potential damage to the SPE surface by the action of heat evolved during the sparking process is considerably minimized compared with the standard setup in which each spark event consists of multiple electrical discharges. Data demonstrated that the sensing properties of the resulting electrodes are significantly improved compared with those achieved when conventional spark generators are employed, as demonstrated for silver-sparked SPEs that exhibit enhanced sensitivity to riboflavin. Sparked AgNp-SPEs were characterized using scanning electron microscopy and voltammetric measurements in alkaline conditions. The analytical performance of sparked AgNP-SPEs was evaluated by various electrochemical techniques. Under optimum conditions, the detection range for DPV was from 1.9 (LOQ) to 100nM riboflavin (R2=0.997), while a limit of detection (LOD, S/N 3) of 0.56nM was achieved. The analytical utility is demonstrated for the determination of riboflavin in the real matrices of B-complex pharmaceutical preparation and an energy drink.

In-air experimental achievement of high-voltage DC power supply to be installed in a tandem electrostatic accelerator system for boron neutron capture therapy application.

The boron neutron capture therapy (BNCT) system developed by the Korea Institute of Radiological and Medical Sciences is a compact neutron source that can be installed at medical institutes. The target energy was accelerated to a maximum of 2.4 MeV-20 mA by introducing a gas stripping device that converts negative hydrogen ions into positive ions. By using the tandem-type accelerator in this way, a high-voltage DC power supply was designed with 1.2 MV-45 mA as the maximum capability. The design was improved to reduce the number of stages of a Cockcroft-Walton voltage multiplier. Hence, the ripple risk of the DC flat top resulting from unwanted stray capacitance was lowered. The overall height and volume of the Cockcroft-Walton voltage multiplier were reduced to less than half those of the existing design method, making miniaturization possible. After such advanced design and manufacturing, performance tests were performed at 750 kV-45 mA under 23 stages of the Cockcroft-Walton voltage multiplier, which is the highest level that can perform at its maximum under in-air conditions. It demonstrated stable performance under in-air conditions without breakdown for 2h, even at 620 kV-35 mA. To reach the final target of 1.2 MV-45 mA, the groundwork is laid for achieving experimental performance while satisfying the optimal requirements in SF6 gas.

Optimal Design Method of High Voltage DC Power Supply EMI Filter Considering Source Impedance of Motor Controller for Electric Vehicle

Passive filters are often used for electromagnetic interference (EMI) suppression on the high voltage (HV) DC side of motor drive systems due to their simple structure and large noise suppression. However, the traditional passive filter design method takes less consideration of the change of the system source impedance, which will lead to almost no insertion loss in some frequency bands or an over-design of the filter. Based on the onboard working conditions of high-voltage and high-current, this article adopts the dual current probe method to obtain the source impedance of the system when it is working, and proposes a filter multi-objective optimization design method based on the genetic algorithm (GA). This method automatically selects the optimal topology of the filter and related component parameters according to the source impedance and load impedance, avoiding the filter resonance phenomenon and over-design problems caused by not considering source impedance. The experimental results show that conducted interference voltage and current of motor drive system with filter designed by the proposed method can pass CISPR25-2016rd level 3.

Design and Optimization of a Magnetron DC–DC Isolated Power Supply With High Efficiency

High-efficiency high voltage dc power supply is the core equipment for magnetron in the microwave industry. This article presents an input-parallel output-serial modular high isolated resonant converter for the magnetron. However, the high stray capacitance of the high isolation transformer brings some challenges, such as high turn-<small>off</small> current, longer dead time, increasing gain, and transformer optimization. A simplified model including the stray capacitances is built to deal with these problems, and the minimum turn-<small>off</small> current is derived after the detailed time-domain analysis. The appropriate deadtime and the maximum magnetic inductance needed for the proposed converter are obtained with the minimum turn-<small>off</small> current. Then, a 15 kW, 60 kV isolation multiple-windings output transformer is designed and optimized for the converter. The insulation design, core shape, losses, and parasitic parameters are calculated thoroughly. The Pareto optimization process optimizes the switching frequency and the transformer&#x0027;s turns to obtain higher efficiency and a more stable gain. The finite element method and time-domain simulation verified the optimized design results. Finally, a 0.8&#x002F;2.5 kV, 15 kW all-SiC dc&#x2013;dc converter module is developed to validate the proposed design. The results indicate that the module efficiency is as high as 98.6&#x0025;.

Development of High Voltage DC Power Supply from Tesla Coil Using Hybrid Energy Sources

Background: High Voltage Direct Current (HVDC) is a well-proven technology used to transmit electricity over long distances by overhead transmission lines or submarine cables. It is also used to interconnect separate power systems, where traditional Alternating Current (AC) connections cannot be used. Objective: In this paper, an HVDC supply has been proposed with the Tesla coil using hybrid energy sources such as solar panels, batteries, and AC main supply with an AC-DC converter. Method: DC voltage is obtained from various hybrid sources and is supplied to the input of the Cockcroft-Walton (C-W) voltage multiplier circuit through DC/AC inversion. Result: The produced HVDC is provided to the Tesla coil to obtain a stable HVDC output. Fractional Order PID (FOPID) controller is used in the system for control purposes to stabilize the output voltage due to load variations. The model was designed in Matlab / Simulink environment. The simulation results show that the proposed design successfully achieved a stable 15 kV HVDC. Conclusion: The advantage of the proposed system is the availability of variable output voltage as per load requirement compared to the fixed limited output voltage generated by conventional HVDC systems.

Inactivation of Penicillium expansum spores in apple juice by contact glow discharge electrolysis and its related mechanism

Penicillium expansum spores in apple juice were treated with contact glow discharge electrolysis (CGDE), and the effect of different parameters on the efficiency of spore inactivation and the related mechanism were investigated. We found that CGDE effectively inactivated spores of P. expansum in the clarified apple juice. CGDE achieved a 3.71 log inactivation of spores in the juice with 1 cm electrode gap, at 520 V, and discharge time for 15 min. CGDE produced hydrogen peroxide in the juice, and the concentration reached 58.1 mg/L after discharged for 30 min. CGDE destroyed the integrity of the cell membrane in the spores, and reduced the activities of superoxide dismutase, catalase, and peroxidase by 68.1%, 81.8%, and 68.0% after discharged for 30 min. In addition, CGDE inhibited mycelial growth, reduced colony diameter by 18.9%, and decreased the lesion diameter by 41.4% in apples surface-inoculated with P. expansum. Taken together, CGDE could inactivate the spores of P. expansum in apple juice by inducing reactive oxygen species accumulation and disrupting the integrity of cell membrane of spores. Industrial relevanceCGDE can effectively inactivate the spores of P. expansum in apple juice. The device of CGDE is composed of a high voltage DC power supply, electrodes and a reaction vessel, which is connected easily with material pipeline, and suitable for handling liquids. Therefore, CGDE can be applicated in treating liquids contaminated with fungal spores in the food industry.

Design method of wide‐band high‐current air‐core inductor EMI filter for high voltage DC power of motor inverter of electric vehicle

Passive filters are often used for electromagnetic interference (EMI) suppression of high voltage (HV) DC power supplies of electric vehicle (EV) motor controllers. The high current of the DC bus saturates the differential mode (DM) magnetic ring, while the leakage inductance of common mode (CM) inductor used as the DM inductance is usually very small, resulting in almost no suppression of DM EMI. A design method of broadband high-current air-core inductor passive filter is proposed. By using the air-core inductor as DM inductor, the problem of easy saturation of the DM inductor core and the small leakage inductance of the CM inductor is solved, and improves the low frequency DM EMI suppression. Through the calculation and selection of the turning frequency point of the multi-stage filter circuit, the effective frequency band can be improved. By analysing the influence of parasitic parameters, the problem of insufficient insertion loss of the filter at high frequency is solved. The experimental verification shows that the proposed air-core inductor filter achieves 50 dB of CM and DM insertion loss in frequency range of 150 kHz–108 MHz, and meets the requirements of system conducted disturbance voltage specified in CISPR25-2016Rd level 3.