Convective Heat Exchange Research Articles

Effects of window view and local airflow on human thermal comfort in a sudden change environment

Transitioning from outdoors to indoors involves a sudden environmental change. However, current thermal comfort standards and design guidelines focus on steady-state environments, which do not fully address the urgent need for comfort during dynamic recovery periods. This study uses a climate chamber experiment to investigate the effects of window view and local airflow on thermal recovery under sudden environmental changes. Twenty participants, after exercising in a 34°C environment for 10 minutes, sat for 60 minutes in a 28°C room (with a microenvironment featuring window view/local airflow). Physiological parameters and subjective responses were measured during this period. The results indicate that under sudden environmental changes, window view significantly positively affects thermal recovery through psychological effects, while local airflow mainly accelerates convective heat exchange. The influence on thermal sensation recovery and recovery speed is as follows: window view and local airflow coupling > local airflow > window view. In terms of physiological parameters, both of them only had a significant effect on skin temperature but not on heart rate and blood pressure. The results of the study not only reveal the key role of indoor microenvironment on the effect and speed of thermal sensation recovery under the sudden change environments, which enriches the theory of dynamic thermal comfort, but also provides a scientific basis for the control strategy of indoor environments under sudden change environments.

Building a model of oil tank water cooling in the case of fire

The object of this study is the process of liquid combustion in spillage, and the subject is the temperature distribution along the wall of a vertical steel tank when it is heated under the thermal influence of fire and cooled by water. A system of equations describing the water cooling of the wall of a vertical steel tank under the conditions of the thermal effect of a fire spilling a flammable liquid has been constructed. The system consists of a heat balance equation for the tank wall, a heat balance equation for the water film flowing over the wall, and a mass balance equation for the water film. The equations take into account the radiative heat exchange with the flame, the environment, the internal space of the tank, as well as the convective heat exchange with the surrounding air, the vapor-air mixture, and the liquid inside the tank, as well as between the water film and the wall. The joint solution to the system of equations makes it possible to determine the temperature distribution along the tank wall and the water film at an arbitrary time point, as well as to determine the thickness and flow rate of the water film at a certain point. The finite difference method was used to solve the system of heat and mass balance equations. It is shown that the insufficient intensity of water supply for cooling leads to boiling of water from the film, as a result of which the wall temperature in such areas can reach 300 °C. A delay in the supply of water, even with sufficient intensity, could lead to the establishment of a film-like mode of boiling. In such a situation, the water film is thrown away from the wall, as a result of which the part of the wall below the film boiling zone remains without cooling. The practical significance of the built model is the possibility of determining the necessary intensity of water supply for cooling the tank and the limit time for the start of cooling

Influence of the thermal insulation position in standard and cool roofs on their contribution to urban heating during heatwaves

The urban heat island, coupled with increasingly intense, frequent and long heat waves, leads to a significant risk of excess mortality and increased energy requirements in urban areas during the summer season. Various cooling techniques are therefore being studied to moderate the intensity of this phenomenon during the hot season. The aim of this study is to quantify the contribution of roofs to urban climate during heatwaves, depending on the position of the insulation in the structure and its radiative properties. This study is carried out in the laboratory, using an experimental set-up to submit roof samples to heatwave conditions. The experimental set up includes a temperature and humidity-controlled climate chamber with a solar simulator. Two roofing configurations are studied: roofs with external thermal insulation (ETI) and roofs with internal thermal insulation. Each configuration is studied for two types of roof: standard (low albedo), and reflective (high albedo). It appears that ETI roofs heat the outside air during the day, but not at night. While ITI roofs heat the ambient air less during the day, they release some of the stored daytime heat during the night. Whatever the structure, increasing solar reflectivity significantly reduces the contribution of roofs to urban heating, although the impact is stronger for internally-insulated roofs, since it reduces the amount of heat released. Finally, for the externally insulated structure, the increase in solar reflectivity reduces daytime convective exchange by 41% and heat entering the building by 75%. For the internally insulated structure, daytime convective heat exchange is reduced by 43%, and the heat stored in the concrete layer is reduced by over 50%.

Effects of charge motion on knock and thermal efficiency under high load condition of a heavy-duty natural gas engine

Nowadays, the carbon-neutral trend and the crude oil crisis have brought natural gas into increasing focus. However, heavy-duty engines fueled by natural gas have been plagued by thermal efficiency and knocking limitation problems. Well-structured charge motions can enhance thermal efficiency and concurrently mitigate knock, however, there is a lack of comprehensive work involving charge motions. In this paper, numerical simulation is employed to investigate the impact of charge motion on knock and thermal efficiency under high load conditions for a heavy-duty spark-ignition natural gas engine. The findings indicate that in the configuration with intense swirl, the diminished turbulent kinetic energy (TKE) at the combustion chamber’s base lessens the convective heat exchange between the fresh charge and the heated exhaust gases, resulting in a noticeable high-temperature zone and triggering hot spots. In configurations with inclined swirl and strong tumble motion, the extensive tumble motion near the spark plug region close to top dead center leads to an asymmetric flame front shape, determining the location of hotspots. The research also revealed that excessive tumbling motion and TKE can increase the likelihood of engine knock, while appropriate cylinder charge motion can improve the knock resistance of the engine to some extent, the maximum reduction in knocking intensity can reach 92.5%. The optimized combustion systems can significantly improve the initial combustion rate, shorten the ignition delay period, and advance the combustion center. With the combined effects of ignition timing and charge motion, the total indicated specific power per unit of fuel mass is increased in the optimized systems. Compared to the original combustion system, the indicated thermal efficiency within the knocking boundary can be improved by 1.11%.

Evaluating thermal sensation in outdoor environments - Different methods of coupling CFD and radiation modelling with a human body thermoregulation model

Thermal comfort is vital in outdoor spaces for social interaction and recreation. With increases in heat wave events and global warming, it becomes more essential to be able to assess heat stresses. Outdoor spaces have asymmetrical and transient environmental factors such as solar radiation, long-wave radiation and natural wind, which makes the thermal perception outdoors largely different from indoors. Traditional thermal comfort models have some limitations and less accuracy when applied to outdoor spaces. The current study focuses on developing a method to assess the human thermal interaction with the complex outdoor environment and the consequent thermal sensation. Computational Fluid Dynamics (CFD) and radiation modelling are coupled to the Joint System Thermoregulation (JOS-3) model to assess the skin temperature, based on which thermal sensation is predicted using the updated thermal comfort model developed by UC Berkeley. The proposed methodology is applied to assess the thermal sensation of human subjects standing in front of an outdoor radiant cooling hub. The important finding is that the one-way coupling, i.e., no skin temperature feedback to the CFD simulation, works reasonably well in the outdoor environment, and that convective heat transfer coefficients available from experimental studies can be coupled with CFD simulated environmental parameters to obtain more reliable convective heat exchange to avoid meshing the geometry of a human body in CFD and further reduce the computing cost.

RESEARCH OF THE DESTRUCTION CONDITIONS OF GLAZING OF ENCLOSING STRUCTURES UNDER THE CONDITIONS OF THERMAL INFLUENCE OF FIRE

The article presents the main results of mathematical modelling of the destruction of glazing of enclosing building structures with translucent elements under fire conditions. The authors analyse literature data on calculating the fire resistance of enclosing building structures with glazing. The results show that improving methods for predicting the fire resistance of glazing is relevant. Mathematical models for the numerical study of the behaviour of glazing under the thermal influence of the standard fire temperature regime are substantiated. Mathematical models of the heat transfer process involve using a non-stationary differential equation of heat conduction with boundary conditions of the third kind, accounting for the convective and radiant heat exchange between the air in the room with the fire and the glazing. As a criterion for the destruction of glazing under the influence of fire, the authors establish the temperature resistance parameter, which is determined based on the mechanical characteristics of the glass. The article highlights the relevant data on the study of temperature indicators and the mechanism of glazing failure, using mathematical modelling with well-founded mathematical models. It obtains the results of the thermal calculation by applying the finite difference method for solving the non-stationary differential equation of thermal conductivity. The methodology for determining the time of glazing failure under the influence of the standard temperature regime of a fire using the calculation parameters obtained based on well-founded mathematical models is substantiated. An analysis of the adequacy of the obtained calculation data was carried out by comparing them with the results of experimental studies using statistical criteria. As a result of the analysis, the authors confirmed the validity of the calculation data. A complete factorial experiment was conducted based on well-founded mathematical models, which revealed the regularities of the dependence of the parameters of thermomechanical processes in single-layer glass on its structural characteristics. The revealed regularities have the form of linear regression dependences of the destruction time on the thickness of the glazing and the maximum length of the glass panel without bars. Using the regularities of the dependence of the parameters of thermomechanical processes in single-layer glazing on its structural characteristics, the authors constructed reference tables for evaluating the fire resistance of enclosing structures with glazing. The research obtained new scientific data on the study of the behaviour of glazing of enclosing building structures under the thermal influence of fire through mathematical modelling, which is the basis for improving the methods of calculating the fire resistance of enclosing structures with translucent elements. Keywords: enclosing building structures, glazing, fire resistance limit, calculation method, glass heat resistance.

Building a model of heating an oil tank under the thermal influence of a spill fire

The object of this study is the process of liquid combustion in a spill, and the subject of research is the distribution of temperature along the wall and roof of a vertical steel tank that is heated under the thermal influence of a spill fire. The heat balance equation for the wall and roof of the tank with oil product was constructed. The assumption of a small thickness of the wall and roof of the tank relative to its linear dimensions makes it possible to move to two-dimensional differential equations of the parabolic type. The equations take into account the radiative heat exchange with the flame, the environment, the internal space of the tank, as well as the convective heat exchange with the surrounding air, the vapor-air mixture, and the liquid inside the tank. Using the methods of similarity theory, estimates of the coefficients of convection heat exchange of the outer surface of the tank with the surrounding air and the inner surface with the vapor-air mixture and liquid in the tank in the conditions of free convection were constructed. The application of the finite difference method for solving the heat balance equations has made it possible to derive the temperature distribution on the surface of the tank at an arbitrary moment in time. It is shown that the value of the coefficient of convection heat exchange of the liquid exceeds the corresponding value for the air-vapor mixture by (1÷2) orders of magnitude. As a result, the part of the wall located below the oil product level is heated to a temperature of (80÷230) °C depending on the viscosity of the liquid. This occurs despite the fact that the value of the mutual radiation coefficient reaches its maximum value at the lower part of the wall. From a practical point of view, this means that the part of the wall above the level of the oil product in the tank can reach dangerous temperature values, and it should be cooled first. The constructed model of tank heating also enables determining the limit time for the start of cooling of the tank.

Numerical investigation of MHD mixed convection in an octagonal heat exchanger containing hybrid nanofluid

Nowadays, the advancement of heat transmission for the heat exchanger device is an important field of research for many researchers. In this work, a numerical study has been conducted to investigate the thermal performance of a mixed convective flow through the octagonal heat exchanger covered by hybrid nanofluid (Cu-TiO2-H2O). A magnetic field has been introduced inside the cavity to investigate the mixed convective hydrodynamics heat flow characteristics. The nanofluid cores absorb/release energy to manage heat transmission by increasing or decreasing inside the cavity domain as the host fluid and dispersed hybrid nanofluid circulate within the cavity. After transforming the governing equations into a generalized, non-dimensional formulation, the finite element approach is utilized to solve the associated equations. Additionally, response surface methodology is also applied to test the responses of the associated factors. Heat transport was examined in relation to the effects of nanofluids fusion temperature, boundary wall properties, Reynolds number, Hartmann number and nanoparticle volume fractions. The outcomes of this study are analysed by measuring streamline profiles, isotherms, average Nusselt number, velocity profile, and 2D and 3D response surfaces of the computational domain. The underlying flow controlling parameters for instance Reynolds number (10 ≤ Re ≤ 200), Hartmann number (0 ≤ Ha ≤100), and nanoparticle volume fractions (0 ≤ ϕ ≤ 0.1), the influences have been considered. The findings also reveal that the thermal performance is being boosted due to augmentation of Re and ϕ, but reverse behavior is noticed for Ha. Furthermore, the response surfaces obtained from response surfaces methodology express that the Re and ϕ have shown positive influence, and Ha has shown negative influence on Nuav. Utilizing a hybrid nanofluid of Cu-TiO2-H2O increases the heat transfer capacity of water to 25.75 %. Moreover, the findings could guide to design of a mixed convective heat exchanger for industrial purposes.

Determining cold strain in cold air: a comparison of two methods of partitional calorimetry to calculate heat storage and debt in cold air with mild hypothermia.

We compared two methods of partitional calorimetry to calculate heat storage and heat debt during cold air (0°C) exposure causing mild core cooling. Twelve participants performed a 5 min baseline in thermoneutral conditions (∼22.0°C, ∼50% relative humidity) followed by cold air exposure (∼0°C) until rectal temperature was reduced by ∆-0.5°C. Partitional calorimetry was used to calculate avenues of heat exchange (radiative, convective, and evaporative), heat storage, and heat debt continuously throughout cold exposure. We compared deriving these variables using prediction equations based on environmental and participant characteristics (PCALEquation Method) versus using measurement tools such as humidity sensors and heat flux discs (PCALHeat Flux Method). There were significant differences between methods (all p≤0.001) for determining heat exchange, heat storage, and heat debt. At ∆-0.5°C, PCALHeat Flux Method had greater levels of radiative and convective heat exchange (PCALHeat Flux Method: -143.0±16.8 W∙m2 vs PCALEquation Method: -123.0±12.9 W∙m2, p≤0.001), evaporative heat exchange (PCALHeat Flux Method: -9.0±1.7 W∙m2 vs PCALEquation Method: -4.1±0.0 W∙m2, p≤0.001), heat storage (PCALHeat Flux Method: -15.0±31.0 W∙m2 vs PCALEquation Method: +6.0±25.9 W∙m2, p=0.020), and heat debt (PCALHeat Flux Method: -692.0±315.0 kJ vs PCALEquation Method: -422.0±136.0 kJ, p≤0.001). Overall, this study found the largest discrepancies between the two methods were when the environmental conditions and skin temperature were in high flux, as well as when core temperature was reduced by ∆-0.5°C. The use of PCALHeat Flux Method may be more advantageous to use in the cold to provide a higher resolution measurement of cold strain.

Natural convection heat transfer in an eccentric annulus filled with hybrid nanofluid under the influence of thermal radiation and heat generation/absorption

This investigation aims to scrutinize the flow and heat transfer characteristics of a hybrid nanofluid composed of Ag-MgO within an eccentric annular space, where the inner circular wall is held at a constant elevated temperature and the outer circular wall is uniformly cooled. Natural convection in such eccentric annular enclosures, with thermal radiation and the effects of heat generation/absorption taken into consideration, plays a vital role in various engineering applications, including solar collectors, nuclear reactors, thermal storage systems, and heat exchangers. The resolution of the fundamental governing equations was executed employing the Gauss-Seidel approach, with the inclusion of a sub-relaxation process, all within the framework of the finite volume method. The impact of the Rayleigh number, radiation number, volume fraction as well as heat generation/absorption coefficient on thermal transfer, flow, and temperature distributions were investigated. It was observed that for low Rayleigh numbers, radiation influences enhance flow stability and improve the conductive heat transfer mode. Conversely, at high Rayleigh numbers, radiation intensifies convective heat exchange. The growth of the Rayleigh number diminishes the impact of heat generation and reinforces the radiation heat transfer process, while heat absorption exhibits the opposite effect. From Nr = 1 onwards, the average Nusselt number values are no longer influenced by an increase in nanoparticle volumetric fraction, and they are solely linked to the radiation number.

Conceptual design and optimization of heat rejection system for nuclear reactor coupled with supercritical carbon dioxide Brayton cycle used on Mars

During the conceptual design of the Mars surface nuclear reactor coupled with supercritical carbon dioxide Brayton cycle, the heat rejection system occupies most of the weight, and reducing the weight of heat rejection system can effectively cut down the transportation cost from Earth to Mars. This paper explored the feasibility of adopting a combination of heat pipe cooling device and convective heat exchanger to design the heat rejection system for the Mars surface nuclear power station, established flow and heat transfer model and weight model, developed a thermal-hydraulic design program for the heat rejection system, and verified its accuracy; then, the NSGA-II multi-objective optimization method is used to optimize the weight of heat rejection system. Pareto front shows that with higher heat rejection proportion of convective heat exchanger, corresponding inlet velocity of Mars' atmosphere should also be increased. As the optimization result of heat rejection system, the ratio of weight to heat rejection is between 0.94 kg/kW and 2.92 kg/kW, and the maximum power consumption of convective heat exchanger accounts for 3.29% of the total power generation.

Balance regulation of heat transfer and flow performance in convective heat exchange process of microchannel plates

As high-performance computing devices continue to evolve toward miniaturization and integration, chip performance has increased significantly. However, chip dimensions are simultaneously shrinking. This trend has led to more challenging high heat flux density issues. Microchannel liquid cooling is an effective way to solve this issue, where the most critical aspect is the balance regulation of heat transfer performance and fluid dynamics. To address this challenge, this study initially divided a complete microchannel plate into two parts: an inlet distribution chamber (IDC) and an array structure. Subsequently, anentransy dissipation rate modeland apumping power consumption modelwere established for themicrochannel inlet diversion chamber, and an optimization design was carried out. This solved the problems of the optimal branch level and optimal channel size for designing the microchannel IDC within a given space. Next, themicrochannel array structurewas optimized to minimize boththermal resistanceandoverall flow resistance. This approach facilitated proactive optimization design for the microchannel array structure within the specified space. Finally, the independently optimizedinlet diversion chamberandarray structurewere combined into a complete optimized microchannel plate. Several comparative structures were also designed under the same constraints. Experimental research was conducted to validate the reasonableness of the optimization. The results indicated that, compared to randomly designed structures, the average overall performance of the optimized structure within the study scope hadincreased by at least 1.16 times, with the highest improvement reaching4.29 times. This study provides a theoretical reference for the active optimization design of microchannel plates in convective heat exchange process.

Modeling transient temperature coupled pressure behaviour for waterflooding well with induced fractures: Semi-analytical model, numerical model, and case studies

Waterflooding is a widely used technique for developing unconventional reservoirs. Long-term waterflooding can lead to the formation of multiple induced fractures. Accurately tracking the location, extent, and dynamic behavior of these induced fractures is crucial. To enhance monitoring capabilities, data obtained from distributed temperature sensors are used to track temperature variations within the wellbore and at the bottom of the well. Combining temperature and pressure inversion techniques helps mitigate the issue of multiple solutions while offering a more comprehensive characterization of multi-induced fractures from various perspectives. In this study, this work presents a model for temperature coupled pressure (TCP) transient analysis. Additionally, this work utilizes COMSOL Multiphysics software to develop and solve a dynamic wellbore temperature (DWT) model. This work proposes a workflow that describes the dynamic behaviour of multi-induced fractures. During model development and solution, this work employs both pressure and temperature transient analysis methods, examining time-dependent non-linear pressure drop and heat transfer variations. Our results reveal that induced fractures exhibit convective heat exchange with the wellbore, resulting in significantly higher temperatures at the induced fracture locations compared to other wellbore locations. By analyzing temperature-wellbore location curves, this work can accurately identify the locations of induced fractures. The TCP model successfully extracts characteristic parameters of induced fractures, while the DWT model allows for monitoring the locations and heights of these fractures. By combining the workflows of both models, this work achieves a comprehensive characterization of the physical properties of induced fractures. In conclusion, this advancement empowers engineers to manage the development of such fractures effectively, thereby averting potential adverse effects on production well performance and preventing the need for well abandonment.

Review on convective and radiation heat transfer between bridges and external environments

The heat exchange between bridges and external environments is the primary cause of the temperature effect on bridges. The complexity of the two-phase (gas–solid) heat transfer mechanism, the diversity of the surface characteristics of bridge materials, and the uncertainties of the environment in which bridges are located make the numerical calculation of the heat exchange between bridges and external environments difficult. Several studies have been conducted by scholars around the world. In this work, the research on convective and radiative heat exchange between bridges and external environments is surveyed, analyzed, and summarized. The influencing factors and calculation methods of bridge temperature are examined, and the convective heat transfer and radiation mechanisms, theoretical calculations, and experimental measurement methods used to investigate the relation between bridges and external environments are summarized and analyzed. The value determination methods for convective heat transfer and radiation absorption coefficients in the calculation of the bridge temperature field are summarized. In addition, the problems and shortcomings of current research are evaluated, and future research directions are identified and discussed.

Dynamics of energy transport on hydromagnetic Casson slippery nanoflow over curved surface

The study of fluid flow over curved surfaces is crucial in various engineering applications, such as designing aircraft wings, turbines, and submarines. Curved surfaces are being explored in various biomedical applications, such as designing stents for blood vessels and implants for bones and joints. Concerning the present applications of curved stretching sheets on fluid dynamics along with trihybrid nanofluids, this study is unique and fills the research gaps and offers solutions to several issues. This work looks at the flow through the boundary layer of an electrically conductive trihybrid nanofluid and the convection heat exchange of a Casson fluid across a curved stretched surface encircled within a circle of radius R. The study considers the effects of thermal radiation using the non-linearized Rosseland approximation, as well as a magnetic field, and hydromagnetic slip. The flow as well as the transfer of heat problem is mathematically described by curvilinear coordinates. Using the combination of the shooting technique and the Runge-Kutta method, similar solutions to the modeled partial differential equations are produced, and the set of non-linear ordinary differential equations with a boundary value solver is implemented through the MATLAB program. The study finds the influence of several limits on critical characteristics such as fluid velocity, coefficient of skin friction, pressure, temperature, and rate of heat exchange over a surface. The findings are shown in tables and graphs. Additionally, a comparative analysis between the current findings and those found in the literature is provided. Blood-containing nanoparticles (GO-SWCNTs-MWCNTs) on curved surfaces could improve drug delivery effectiveness, growth of synthetic tissues or organs with complex structures and effective cancer therapy treatment.

Investigation of aluminum particle ignition dynamics in various propellant environments

The ignition delay of aluminum particles can be profoundly influenced by the agglomeration and combustion characteristics of solid propellants. In this experimental study, the ignition of individual aluminum particles in nitrate ester plasticized polyether (NEPE) and hydroxyl‑terminated polybutadiene (HTPB) propellant atmospheres was examined using laser ignition tests and high-speed photography. Focus was directed at the effects of the atmospheric composition, pressure, and aluminum particle size (500, 800 and 1000 µm). It was observed that the non-homogeneous reaction heat generation and convective heat exchange rates during particle ignition could be increased by increasing the CO2 content or ambient temperature, resulting in a shorter ignition delay time. This explains why aluminum particles tended to burn more efficiently in nitrate ester plasticized polyether than in hydroxyl‑terminated polybutadiene. In addition, it was found that the ignition delay time decreased with increasing pressure and was inversely proportional to the particle size squared. An ignition model for aluminum particle ignition in a multi-component atmosphere was developed and validated to describe the temperature change and energy transfer during ignition. The calculated ignition delay times were found to be within 5% of the experimental values. The model also showed that increasing the ambient temperature was more effective than increasing the CO2 content at enhancing ignition, and that CO2 was more effective than O2, which was itself more effective than H2O. Overall, this study provides useful insight into the ignition characteristics of aluminum particles in different propellant environments. The results could be used to develop more effective propellant formulations, optimize combustion processes, and improve safety in the handling and use of aluminum-based propellants.

Coupled Axisymmetric Thermoelectroelasticity Problem for a Round Rigidly Fixed Plate

Introduction. To describe the operation of temperature piezoceramic structures, the theory of thermoelectroelasticity is used, in which the mathematical model is formulated as a system of nonself-adjoint differential equations. The complexity of its integration in general leads to the study of problems in an unrelated formulation. This does not allow us to evaluate the effect of electroelastic fields on temperature. The literature does not present studies on these problems in a three-dimensional coupled formulation in which closed solutions would be constructed. At the same time, conducting such studies allows us to understand the interaction picture of mechanical, thermal and electric fields in a structure. To solve this problem, a new closed solution of a coupled problem for a piezoceramic round rigidly fixed plate has been constructed in this research. It provides for qualitative assessment of the cross impact of thermoelectroelastic fields in this electroelastic system.Materials and Methods. The object of the study is a piezoceramic plate. The case of unsteady temperature change on its upper front surface is considered, taking into account the convection heat exchange of the lower plane with the environment (boundary conditions of the 1st and 3rd kind). The electric field induced as a result of the thermal strain generation is fixed by connecting the electrodated surfaces to the measuring device. The thermoelectroelasticity problem includes the equations of equilibrium, electrostatics, and the unsteady hyperbolic heat equation. It is solved by the generalized method of finite biorthogonal transformation, which makes it possible to construct a closed solution of a nonself-adjoint system of equations.Results. A new closed solution of the coupled axisymmetric thermoelectroelasticity problem for a round plate made of piezoceramic material was constructed.Discussion and Conclusion. The obtained solution to the initial boundary value problem made it possible to determine the temperature, electric and elastic fields induced in a piezoceramic element under arbitrary temperature axisymmetric external action. The calculations performed provided determining the dimensions of solid electrodes, which made it possible to increase the functionality of piezoceramic transducers. Numerical analysis of the results enabled us to identify new connections between the nature of external temperature action, the deformation process, and the value of the electric field in a piezoceramic structure. This can validate a proper program of experiments under their designing and significantly reduce the volume of field studies.

Numerical Simulation and Sensitivity Analysis Using RSM on Natural Convective Heat Exchanger Containing Hybrid Nanofluids

This work presents a numerical analysis for exploring heat transfer phenomena in an enclosed cavity using magnetohydrodynamics natural convection. Because of the numerous real-world applications of nanofluids and hybrid nanofluids in industrial and thermal engineering developments, hybrid nanofluids are used as fluid mediums in the fluid field. A hexagonal-shaped heat exchanger is taken with two circular surfaces along the middle part. The upright circular surface acts as a homogeneous heat source, while the lower circular surface functions as a heat sink. The remaining portions of the adjacent walls are thermally insulated. The copper (Cu) and titanium dioxide (TiO2) nanoparticles are suspended into water to make a hybrid nanofluid. For solving the corresponding governing equations, the weighted-residual finite element method is applied. To explain the major outcomes, isotherms, streamlines, and many others 2D and 3D contour plots are involved graphically with a physical explanation for different magnitudes of significant parameters: Rayleigh number 103≤Ra≤106, Hartmann number 0≤Ha≤100, and nanoparticle volume fraction 0≤ϕ≤0.06. The novelty of this work is to apply response surface methodology on the natural convective hybrid nanofluid model, to visualize 2D and 3D effects, and to study the sensitivity of independent parameters on response function. Due to the outstanding thermal properties of the hybrid nanofluid, the addition of Cu and TiO2 nanoparticles into H2O develops the heat transfer rate to 35.85% rather than base fluid. Moreover, a larger magnitude of Ra and the accumulation of mixture nanoparticles result in the thermal actuation of a hybrid nanofluid. With greater magnetic impact, an opposite response is exhibited.

Automation studies of thermo-stressed state of the core when exposed to local heat fluxes, heat transfer

Many load-bearing elements of power plants are influenced by local heat flows and convective heat exchangers. Because of this, a deformed thermostress state is formed in the bearing elements in the form of a rod of limited length. Therefore, it is important to develop special computational algorithms and corresponding programs for automated research of rods of limited length. At the same time, the developed system must take into account the physical-mechanical and geometric characteristics of the studied core and the simultaneous presence of local convective heat exchange.This work uses the fundamental laws of energy saving. The developed calculation algorithm is implemented in the form of an IBM PC Python program. The results are presented in tables.

Study on the convective heat exchange coefficient of concrete surface considering the surface roughness

A heat exchange experiment of concrete surface under different roughness conditions was conducted, and the convective heat exchange coefficient model of concrete surface influenced by many factors was deduced and developed. The model comprehensively considers the effects of concrete surface roughness, wind speed, air humidity and thermal conductivity on the surface heat exchange performance. We obtained the model parameters from experimental data, which captured the convection heat transfer process under controlled laboratory conditions. The comparison between the calculation result and the measurement data is good enough, and prove the selection value of the model parameters are very good. The new convective heat exchange model can better reflect the heat exchange of the concrete structure surface under complex boundary conditions, provide support for more accurate simulation analysis of concrete temperature field, and provide the possibility for better calculation of concrete temperature stress and control of temperature cracks.