Particle Concentration Research Articles

Structure–property correlation assessment of LLDPE‐based biocomposites with Azadirachta Indica wood flour

AbstractThis research explores the development of new composite material by integrating Azadirachta Indica (AI) with LLDPE to create wood‐plastic composites using the rotational molding process. By examining various proportions of AI wood flour blended with LLDPE, we investigated their impact on mechanical and physical properties. Our tests elucidate a clear correlation between mechanical properties and composite morphologies. Despite identical molding conditions, higher wood particle concentrations reduced mechanical properties compared to lower concentrations. Remarkably, a 12% wood content emerges as optimal, yielding a tensile modulus of 3.69 MPa and a flexural modulus of 468.5 MPa, with an acceptable reduction of 11% density and 13% porosity versus pure LLDPE. Additionally, we observed declines in tensile strength, impact strength, and hardness by up to 23%, 62%, and 11%, respectively, compared to neat LLDPE. Natural fillers enhance aesthetics, making these materials ideal for consumer products like garden equipment and furniture accessories.

Dyslipidemias in multiple sclerosis

PurposeTo investigate the frequency of dyslipidemia phenotypes in multiple sclerosis and to assess the associations with lipoprotein particle size distributions. MethodsThis cross-sectional study included 203 healthy controls (HC), 221 relapsing-remitting MS (RRMS), and 126 progressive MS (PMS). A lipid profile with total cholesterol, high-density lipoprotein cholesterol (HDL-C), triglycerides, and apolipoprotein B levels were measured. Low density lipoprotein cholesterol (LDL-C), very low-density lipoprotein cholesterol, large buoyant LDL-C and small dense LDL-C were calculated using the Sampson-NIH equations method. Dyslipidemia phenotypes were categorized by their nonHDL-C and triglyceride values. The diameters and concentrations of triglyceride-rich lipoprotein particles (TRLP), LDL particles (LDLP), and HDL particles (HDLP) were measured with proton NMR lipoprotein profiling. Serum proprotein convertase subtilisin/kexin type 9 (PCSK9) levels were obtained using immunoassay. ResultsThe frequencies of normolipidemia, and various dyslipidemia phenotypes were similar in HC, RRMS, and PMS. The size of the TRLP, very large TRLP, large TRLP, and small LDLP concentrations had a decreasing pattern of HC>RR>PMS. The lowest tertile of EDSS was associated with higher concentrations of HDLP and small HDLP in PMS. PCSK9 was associated with concentration of HDL particles, primarily via its effects on the concentration of small HDL particles. ConclusionsThere were no differences in the frequency of dyslipidemias in MS compared to healthy controls. Higher HDLP concentrations are associated with lower disability in PMS.

Correlating scatterer concentration and intensity threshold of random laser in niobium oxide particle colloids with dye solution

Our study examines how the concentration of scatterers affects the intensity threshold of random laser (RL) action in colloids made of niobium oxide particles and Rhodamine B dye. This is the first reported instance of RL action in niobium oxide. We kept the dye (gain medium) concentration constant and quantified how varying concentrations of niobium oxide particles (scatterers) affect the RL intensity threshold. Our findings indicate an inverse relationship between the concentration of niobium oxide particles and the RL threshold. Increasing the niobium oxide concentration from 0.32 mM to 2.50 mM decreased the RL threshold by up to 70 %, suggesting that higher scatterer densities lead to enhanced efficiency of the lasing process. We noticed that the RL intensity thresholds decrease concerning scatterer concentration, highlighting the significant impact of scatterer density on lasing efficiency. These results could provide a better comprehension of the mechanics of RL in disordered media and emphasize the essential role of scatterer density in determining RL efficiency. Our work deepens the understanding of RL dynamics and lays the groundwork for designing and optimizing colloidal RL systems for various applications such as imaging and optical sensing.

Study on the microstructure, mechanical and corrosion behaviors of 2A12 Al matrix composites containing B4C and 50% K2TiF6 flux

This study presents an innovative exploration into the development and characterization of boron carbide (B4C) reinforced aluminum (Al) metal matrix composites (AMMCs), specifically focusing on the 2A12 Al alloy. Utilizing a cutting-edge vacuum induction melting process, the research investigates the effects of varying B4C particle concentrations in conjunction with 50% K2TiF6 flux additions. This novel approach aims to enhance the microstructural integrity, mechanical properties, and corrosion resistance of the AMMCs. The research unveils a significant improvement in microhardness and tensile strength with the increase of B4C content. This enhancement is attributed to the efficient load transfer mechanism from the aluminum matrix to the B4C phase and the thermal expansion coefficient mismatch-induced dislocations. A critical finding of this study is the uniform distribution of B4C particles and the formation of a Ti-rich layer around these particles, facilitated by the K2TiF6 flux. This layer acts as a barrier, minimizing interfacial reactions. Electrochemical testing reveals that there is a slight decrease in corrosion resistance with increased B4C content. The outcomes of this research contribute to the field of metal matrix composites, offering a path forward for the application of B4C-reinforced AMMCs in demanding industrial environments where high strength, stiffness, and durability are critical. The study's findings open new avenues for advanced materials development in aerospace, automotive, and energy sectors.

Analysis of the impact of exfoliated graphene oxide on the mechanical performance and in-plane fracture resistance of epoxy-based nanocomposite

Graphene oxide (GO) is a versatile material, derivative of graphene, and it has gained significant attention in the field of polymer nanocomposites due to its exceptional properties and unique structural features. These characteristics make it a successful secondary reinforcing agent for enhancing mechanical performance, fatigue resistance, and other various physical and thermal properties of nanocomposites. However, the low fracture toughness of nanocomposite has restricted the overall structural applications. In this research work, the epoxy nanocomposites were prepared with different weights of exfoliated graphene oxide (E-GO) nanoparticles by using a dual mixing probe ultra-sonication for homogeneous distribution and proper dispersion. A substantial enhancement in mechanical performance and fracture toughness of nanocomposite was observed. The good dispersion and interfacial adhesion among E-GO and epoxy matrix were investigated through the critical analysis of the fracture surfaces of the nanocomposite. The enhancement of mechanical performance of E-GO nanofiller-reinforced epoxy composite was observed superior at 1 wt. % of GO60 particle concentration. The maximum increment of mechanical properties such as tensile strength, flexural strength, and work of fracture were 40.763, 39.23, and 12.106 % respectively, whereas maximum tensile modulus and flexural modulus were 19.3724, 27.63 % at 1.5 wt. % of GO60 as compared to the neat composite. However, in the case of fracture toughness and energy, maximum improvement of 1.256 Mpa.m1/2 and 0.472 KJ/m2 respectively was observed at 1 wt. % of GO60. Such enhancement was primarily due to the bolstering of in-plane crack propagation resistance in the nanocomposites. Additionally, the highlight point in thermomechanical properties of the polymer nanocomposite is optimal storage modulus and damping factor such as 4066.75 MPa, and 0.46 respectively, for the GO60 at 1 wt.% nanocomposite. Moreover, GO60 at 1 wt.% demonstrates greater thermal stability, withstanding up to 50% material degradation at 413.65°C.

Research on characteristics and influencing factors of road dust emission in a southern city in China.

One of the primary causes of urban atmospheric particulate matter, which is harmful to human health in addition to affecting air quality and atmospheric visibility, is road dust. This study used online monitoring equipment to examine the characteristics of road dust emissions, the effects of temperature, humidity, and wind speed on road dust, as well as the correlation between road and high-space particulate matter concentrations. A section of a real road in Jinhua City, South China, was chosen for the study. The findings demonstrate that the concentration of road dust particles has a very clear bimodal single-valley distribution throughout the day, peaking between 8:00 and 11:00 and 19:00 and 21:00 and troughing between 14:00 and 16:00. Throughout the year, there is a noticeable seasonal change in the concentration of road dust particles, with the highest concentration in the winter and the lowest in the summer. Simultaneously, it has been discovered that temperature and wind speed have the most effects on particle concentration. The concentration of road dust particles reduces with increasing temperature and wind speed. The particle concentrations of road particles and those from urban environmental monitoring stations have a strong correlation, although the trend in the former is not entirely consistent, and the changes in the former occur approximately 1 h after the changes in the latter.

Beta-cyclodextrin–Phyllanthus emblica emulsion for zinc oxide nanoparticles: Characteristics and photocatalysis

Abstract This study presents a new approach for producing zinc oxide nanoparticles (ZnONPs) utilizing an emulsion of beta-cyclodextrin (β-CD) and Phyllanthus emblica fruit extract. When synthesized, the particles were around 90 ± 5 nm in size. The zeta potential investigation yielded a value of −27.1 mV. The generated ZnONPs exhibited 83.70% anti-oxidant activity as well as good radical scavenging capabilities. The catalytic activity of ZnONPs was investigated using rhodamine B dye, and they displayed that maximum photocatalytic degradation was found to be 90.32% when exposed to UV light and 50.5% when not exposed to UV light. The kinetic investigation of photocatalytic degradation employs pseudo-first-order rate kinetics, with a rate constant of 2.5 × 10−2 under UV irradiation and 1.1 × 10−2 without irradiation. Anti-bacterial tests against Escherichia coli bacteria demonstrated the particles’ anti-bacterial characteristics. Anti-cancer studies were carried out using KB-31 cancer cells at varying particle concentrations. The studies confirmed that the particles produced are anti-cancer. In conclusion, this study reports a new green synthesis method to fabricate ZnONPs with high anti-microbial, anti-oxidant, and anti-cancer properties and suitable for various biomedical applications.

Failure analysis of erosion wear of the pipeline after 30° elbow by adsorbent particles

An adsorbent transport pipeline after a 30° elbow experienced premature perforation and leakage during service. The failure analysis was performed by means of morphology observation, damaged surface analysis and computational fluid dynamics (CFD) simulation. The results revealed that thickness thinning occurred only on the upper wall, and the severely thinned region exhibited a special striated groove morphology. The main cause of pipeline failure was attributed to erosive wear caused by adsorbent impacts on the wall. Due to the particle redistribution process under the action of multiple force fields in the small bending angle elbow, the straight pipeline after the elbow had a very complex inlet boundary condition, so that the particle concentration at the upper wall was substantially increased. Besides, the sliding motion of the particles on the wall surface was greatly intensified. Cutting deformation became the main form of erosion damage, which induced an alteration in the erosional morphology of the failed pipeline and the backwardness of the leakage site.

Cost-effective Production of Titania Nanoparticles for the Modification of Transformer insulating oil

Nanofluids are prospective solutions for improving the transformer dielectric strengthby adding nanoparticles to the standard oils used in transformers.Oil-based titania nanofluids are becoming increasingly popular due to their superior insulating qualities and distinctive thermal performance, and they areconsideredas possible replacements in the domains of transformer insulating oils.This paper describes the industrial synthesis of titania nanoparticles for improving the insulating characteristics of virgin oil used in transformers.The titania nanoparticles were analyzed using an X-ray diffractogram (XRD), which revealed a prominent peak at Bragg angle 25O, indicating that the titania nanoparticles were generated in the anatase phase. Fourier transform infrared (FTIR) spectroscopy study endorsed the formation of Ti-O-Ti, Ti-OH, C-H and O-H stretching vibrations at 760 cm-1, 1345cm-1, 2475cm-1, and 3646 cm-1 wavenumbers respectively. Field emission scanning electron microscopy (FESEM) and Atomic Force Microscopy (AFM) examinations on the produced titania nanoparticles revealed that the particles had a circular shape with a diameter of 55nm and an average roughness value of roughly 3.6 nm respectively.The viscosity of the host virgin oil and the nanoparticles-filled nanofluid were examined, and higher viscosity values were found as particle concentration increased.The effective conductivity study with the zeta potential and thermal conductivity fluctuation with temperature variation also revealed that at higher temperatures, conductivity with the zeta potential increased and thermal conductivity dropped. Furthermore, the breakdown strength of the titania nanoparticles-based virgin oil was observed to be effectively increasedwith the particle concentration.

A novel Pickering emulsion gels stabilized by cellulose nanofiber/dihydromyricetin composite particles: Microstructure, rheological behavior and oxidative stability

Particle concentrations (w) and oil content (Φ) are crucial factors influencing the gel stability of Pickering emulsions. To understand the stabilization mechanism comprehensively, we prepared emulsion gels stabilized by CNF/DMY composite particles at various w (0.5–1.5 wt%) and Φ (0.2–0.6, v/v). The microstructure revealed the adsorption of these particles at the oil-water interface, with excess particles forming a three-dimensional network structure in the continuous phase. Rheological studies showed that the network structure of Pickering emulsions was significantly influenced by w and Φ, resulting in improved emulsion gel strength that hindered the movement of oil droplets and oxygen in the continuous phase, thereby enhancing emulsion stability. Three scenarios for the critical strain (γco) were observed: at Φ = 0.2, γco decreased with increasing w, while at Φ = 0.4, γco increased with increasing w. At Φ = 0.6, γco remained relatively constant regardless of w. In conclusion, adjusting particle concentration and oil content enabled the control of microstructure, rheological properties, and antioxidant capacity of emulsion gels. These findings could be a valuable resource for formulating and ensuring the quality of emulsion gel-based products in the food industry.

Full-scale evaluation of FFU configurations in an optical cleanroom injection molding for improving thermal performance and contaminant removal

Cleanrooms are critical in the semiconductor industry, particularly for optical fabrication, where even minor contamination can compromise product quality. Effective airflow and uniform airflow distribution help to prevent contaminant accumulation, mitigate temperature variations, and avoid cross-contamination, which is crucial for achieving high-quality results and compliance with industry standards. This study introduces a novel approach to optimizing Fan Filter Unit (FFU) configurations to enhance thermal performance and contaminant removal in cleanroom settings. Integrating field measurements with advanced Computational Fluid Dynamics (CFD) simulations to comprehensively evaluate four distinct FFU designs, from dispersed to centralized configurations, focused on their impact on airflow dynamics, temperature uniformity, and particle concentration. The study identifies a significant advancement in FFU configuration by demonstrating that centralized arrangements (Designs 2 and 4) substantially improve cleanroom performance. Design 4 emerged as the most effective, showcasing a marked improvement in airflow circulation, a 12% reduction in temperature variation, and a 15% decrease in particle concentration compared to conventional designs. This achievement underscores the novel contribution of this study in optimizing FFU configurations to enhance both thermal performance and contaminant control. These findings not only advance the theoretical understanding of FFU design but also provide practical insights for improving cleanroom environments. The study offers a significant step forward in developing efficient cleanroom designs, contributing valuable guidelines for achieving good environmental control in sensitive manufacturing processes.

Particle motion characteristics on the rotational flow pneumatic conveying of horizontal-vertical pipeline

In this study, a rotational flow device (rotational blade) is developed and installed in the upstream of the particle inlet with the aim of improving the efficiency and capacity of pneumatic conveying. Firstly, this study analyzed the energy-saving effect of rotational flow based on the pressure drop and power consumption. The results shown that the optimal velocity can be reduced by a maximum of 18.7% and the power consumption coefficient can be reduced by a maximum of 9.8%. Furthermore, the distributions of particle concentration, velocity and pulsation velocity are analyzed by using electrical capacitance tomography (ECT) and particle image velocimetry (PIV) system. It is found that the particle velocity and velocity pulsation intensity for rotational flow are higher, and they have the ability to enhance particle suspension. Then, the power spectrum of the particle pulsation velocity shown that the rotational flow exhibited higher peak value at lower frequencies, indicating the particles are not easily deposited at pipe bottom. Finally, the auto-correlation of particle pulsation velocity indicated that the particle motion is more stable and has a longer period at low particle concentrations. The skewness factor and probability density function of particle pulsation velocity indicated that the use of rotational blades makes the particle pulsation velocity to deviate from the Gaussian distribution.

Pharmaceutical Applications and Advances with Zetasizer: An Essential Analytical Tool for Size and Zeta Potential Analysis

Abstract: Zetasizer is an advanced device that measures various properties of particles or molecules suspended in a liquid medium. It is extensively used for evaluating the size of nanoparticles, colloids, and biomolecular particles, and for determining particle charge. There are several analytical techniques by which the size, zeta potential, and molecular weight can be determined, like Dynamic Light Scattering (DLS) that measures the size of particles in dispersed systems, which can range from sub-nanometers to several micrometers in diameter. Electrophoretic Light Scattering (ELS) analyzes the mobility and charge of particles, also known as the zeta potential. Static Light Scattering (SLS) determines the molecular weight of particles in a solution. The Zetasizer is part of the Zetasizer Advance range of benchtop systems available for laboratory use. The Zetasizer Ultra model offers unique measurement capabilities, such as Multi-angle Dynamic Light Scattering (MADLS) and particle concentration. These features offer a deeper understanding of samples, making the Zetasizer a vital instrument in numerous scientific and industrial applications. In this review, we have discussed Zetasizer’s principles for the determination of particle size, zeta potential, and molecular weight, along with its qualification and applications in different formulations.

Stabilizing emulsions by ultrasound-treated pea protein isolate - tannic acid complexes: Impact of ultrasonic power and concentration of complexes on emulsion characteristics

This work aimed to investigate the feasibility of stabilizing oil-in-water (O/W) emulsions by ultrasound-treated pea protein isolate-tannic acid (UPPI-TA) complex. The stability and microstructure of the O/W emulsions were evaluated at different ultrasonic powers (0–1000 W) and UPPI-TA complex concentrations (0.25–2.0 wt%). The contact angle (θ) of UPPI-TA was 59.6°, which was suitable for stabilizing O/W emulsions. At an ultrasonic power of 800 W, the droplet size and creaming index (CI) of emulsions decreased, and the apparent viscosity and interfacial protein adsorption content increased with increasing UPPI-TA concentration. In particular, emulsions with 1.5 % UPPI-TA showed the lowest CI, the highest interfacial protein adsorption content and viscoelasticity, as well as the best storage and thermal stability. These results showed that the suitable modifications of ultrasonic emulsification power and particle concentrations were a new potential approach to stabilize the O/W emulsions by ultrasound-treated pea protein isolated-tannic acid complex.

S. hispanica mucilage/ ZnO based films: Preparation, characterization, and potential application

The use of plastic for food packaging is a major contributor to environmental pollution. To address this issue, biopolymeric films have emerged as a potential alternative to plastic products commonly used in food packaging. These biopolymeric films can be enhanced with antimicrobial agents to make them more effective. This study aimed to develop and evaluate the properties of films made from Salvia hispanica mucilage and ZnO particles. The mucilage was obtained by filtering and drying seeds, while ZnO was synthesized using the forced hydrolysis of ZnC₄H₆O₄ and NaOH. The films were produced by combining the mucilage with varying concentrations of ZnO (0.1, 0.5, and 1.0%) using a casting method. Tests were conducted to evaluate the films' physical, chemical, and biological properties. X-ray diffraction analysis showed that ZnO was present, while scanning electron microscopy revealed the presence of C, O, and Zn elements. Fourier transform infrared spectroscopy confirmed the presence of S. hispanica mucilage. Thermogravimetric analysis showed that the films were thermally stable at temperatures below 225°C. Dynamic mechanical analysis revealed that the 0.1% film had the best resistance compared to the 0.5% and 1.0% films. Finally, the study found that the antimicrobial activity of the films depended on the concentration, size, and morphology of the ZnO particles. In conclusion, further research is needed to create films that can effectively inhibit pathogenic bacteria growth in food and be a viable alternative to plastic for food packaging.

The plausible pathway of air pollutants and the respiratory system among COVID-19 patients: a systematic literature review

Studies evidence links air pollution to increased risk of COVID-19 infection and severity during the pandemic. Nonetheless, those studies are unable to discuss specific pollutants, such as particulate matter, Sox, and NOx. This systematic literature review aimed to summarize the most recent studies on the links between pollutants and their effects on the respiratory system, in this case, mostly on COVID-19 patients. We searched using electronic databases (PubMed, Springer, ScienceDirect, and Sage) in May 2023. The keywords chosen were connected to respiratory diseases and air pollution. All relevant studies published in peer-reviewed journals between 2020 and 2023 and written in English were considered. We excluded letters and non-original articles. Relevant keywords were used to select papers. A total of 11 articles are eligible to be included in the present review study. It was reported that countries with a high prevalence of COVID-19 also have greater concentrations of surface air particles (PM10 and PM2.5) due to vehicle exhaust and industrial pollution. PM-virus aggregates spread easier across the lungs and the top respiratory system, facilitating viral attachment to the lung epithelium. This study found that tiny particles with an aerodynamic dimension fewer than 2.5 μm (PM2.5) or ten μm (PM10) have the most significant potential influence on the respiratory system compared to other pollutants.

A correlation study of road dust pollutants, tire wear particles, air quality, and traffic conditions in the Seoul area (South Korea)

The interdependence of traffic dynamics and air quality on the concentrations of tire wear particles (TWP), heavy metals, and carbon black (CB) in road dust collected from 15 locations in Seoul, South Korea, was assessed. Pearson correlation, principal component analysis, and network analysis were employed to evaluate the correlations among traffic volume, vehicle speed, air quality parameters (PM10, PM2.5, NOx, and CO), and the concentrations of TWP (5,934 to 16,253 mg/kg, average 9,581±4,086 mg/kg), CB (371 to 22,287 mg/kg, average 4,291±6,096 mg/kg), and heavy metals (Cr, Mn, Fe, Ni, Cu, Zn, As, Cd, and Pb) in road dust. The enrichment factors for heavy metals and the pollution index of TWP and CB were also calculated to evaluate the contribution of vehicle-derived particulate substances to road dust contamination. It was found that Cluster B, characterized by traffic-related variables such as traffic volume, vehicle speed, and heavy metals (Zn, Cd, and Pb), was significantly correlated with these pollutants, with correlation coefficients reaching up to 0.933. TWP was identified as a significant mediator in the increase of Zn, Pb, and Cd concentrations linked to traffic activities, contributing to pollution levels that were 2 to 16 times higher than the geochemical background. The presence of TWP and CB in road dust was identified as an indicator of contamination from traffic-related activities, highlighting the importance of Zn, Pb, and Cd as emerging pollutants that require targeted management strategies.

Characterization of hybrid silicate materials based on ceramic glazes and waste London underground dust

In “London Underground” stations, a high concentration of dust particles containing organic and inorganic matter of varying chemical composition. “London underground dust” is created from train wheels and brakes grinding against steel tracks and collected in filtration systems. The experiment will focus on using “London Underground Dust” to colour the ceramic facing tiles intended for re-use in newly built London Underground stations. The phase composition, particle size distribution surface area, morphology, and thermal behavior of collected dust were studied by XRD, XRF, SEM-EDS, BET, heating microscopy, STA-MS, UV–VIS spectroscopy. The substrate tiles for glazing experiments were prepared from local London clay. The mixtures of glazes and collected or milled dust were sprayed on the substrate tile's surface, dried and finally fired at 1060 °C. The influence of used materials weight ratio and dust milling time were shown as crucial parameters to obtain optimal final glaze colour.

MβCD inhibits SFTSV entry by disrupting lipid raft structure of the host cells

Severe fever with thrombocytopenia syndrome virus (SFTSV), recently named as Dabie bandavirus, belongs to the family Phenuiviridae of the order Bunyavirales, is a newly-identified bunyavirus with a case fatality rate of up to 30%, posing a serious threat to public health. Lipid rafts on plasm membranes are important for the entry of enveloped viruses; however, the role of lipid rafts in bunyavirus entry remains unclear. In this study, we found that methyl-beta-cyclodextrin (MβCD), a drug that disrupts cholesterol in lipid rafts of cell membranes, inhibits SFTSV infection. Additionally, there is a back-complementary effect of SFTSV infection upon the addition of cholesterol. Moreover, the concentration of SFTSV particles in lipid rafts during entry directly indicated the role of lipid rafts as a gateway, whereas MβCD could inhibit SFTSV entry by affecting the structure of lipid rafts. In an in vivo study, MβCD also reduced the susceptibility of mice to SFTSV infection. Our results suggest that SFTSV can interact with Talin1 proteins on lipid rafts to enter host cells by endocytosis of lipid rafts and reveal the potential therapeutic value of MβCD for SFTSV infection.

Synthesis of Undoped and Mixed Binary Transition Metals (Ni-Co)-Doped Cupric Oxide Nanostructures: Structural Characteristics, Optical Behavior, and Biological Activity

In this work, co-precipitation-assisted undoped and various concentrations (1%, 3%, and 5%) Ni-Co-doped CuO nanostructures have been synthesized to test the biomedical applications. The structure, optical band gap, zone of inhibition width, hemocompatibility, and free radical scavenging activity of the CuO are significantly varied by introducing various concentrations of co-dopants compared to the undoped CuO. The single phase of monoclinic and heterogeneous crystal systems (monoclinic CuO, hexagonal Co, cubic NiO, and Co3O4) for undoped CuO and all Ni-Co-doped CuO samples was identified by the powder XRD tools. Microstructural properties were tuned in each dopant concentration of Ni-Co in the CuO, which confirmed through FE-SEM analysis. Heterogeneous structures (spherical particles/sheet-like particles) were noticed in the HR-TEM studies of 5% Ni-Co-doped CuO nanostructures. Synthesized compounds related to the elements (Cu, O, Co, and Ni) were traced with the help of the EDX and XPS study. The photoabsorption spectra and optical band gap values of the undoped CuO and co-doped CuO samples were significantly varied. Antimicrobial studies of the undoped CuO and Ni-Co co-doped CuO against E. coli and S. mutans bacterial strains were performed, and their outcomes of the zone of inhibition (ZOI) values have been discussed in detail. The synthesized undoped and various concentrations of CuO particles were taken to investigate their compatibility via hemolytic study. Hemolysis results showed that both the synthesized undoped CuO and Ni-Co doped CuO nanostructures are highly hemocompatible. In addition, compatibility natures are varied with increasing concentrations from 1% to 5% Ni-Co dopant in the CuO samples. The DPPH assay was employed to evaluate the antioxidant properties of the synthesized particles by determining their free radical scavenging (FRS) activity percentages. It was observed that Ni-Co-doped CuO exhibited better antioxidant properties than undoped CuO due to the higher FRS percentage.