Mechanical Properties Of Composites Research Articles

Upcycling Post-Consumer Paint Pail Plastic Waste

The need for ending plastic waste and creating a circular economy has prompted significant interest in developing a new family of composite materials through recycling and recovery of waste resources (including bio-sourced materials). In this work, a family of natural fiber-reinforced plastic composites has been developed from paint pail waste recycled polypropylene (rPP) and waste wool fibers of different diameter and aspect ratio. Composites were fabricated by melt processing using polypropylene-graft-maleic anhydride as a compatibilizer. The internal morphology, interfacial and thermal characteristics, viscoelastic behavior, water sorption/wettability, and mechanical properties of composites were studied using electron microscopy, high-resolution synchrotron Fourier transform infrared microspectroscopy, thermal analysis, rheology, immersion test, contact angle measurement, tensile test and flexural test. The composite matrix exhibited an internal morphology of coalescent micro-droplets due to the presence of polyethylene and dry paint in the rPP phase. In general, the rheological and mechanical properties of the composites comprising higher-aspect-ratio (lower diameter) fibers exhibited relatively superior performance. About an 18% increase in tensile strength and a 39% increase in flexural strength were measured for composites with an optimal fiber loading of 10 wt.%. Interfacial debonding and fiber pull-out were observed as the main failure mechanism of the composites. The developed composites have potential for applications in automotive, decking, and building industries.

A review on recent applications of machine learning in mechanical properties of composites

AbstractComposites are undergoing extensive research and utilization due to their excellent mechanical properties, driven by human needs. Traditionally, the research methods in materials science predominantly rely on empirical theory or experimental trial and error approaches. However, the increased complexity of composite materials results in a greater intricacy in their mechanical behavior. Consequently, the utilization of traditional research methods may not achieve sufficient efficiency. Materials science is rapidly transitioning into a data‐driven era, with machine learning (ML) emerging as a potent tool to expedite materials development and enhance properties prediction. Significant advancements have been achieved in the application of ML to the study of composite mechanics. In this review article, we elucidate various ML methods employed in the construction of constitutive models for isotropic and anisotropic composites, and delve into the research on construction ML models that leverage input data derived from composite processes, structures, and environmental conditions to predict material mechanical properties. Additionally, we summarize recent noteworthy ML applications in composite design and optimization. Finally, possible prospective viewpoints are proposed for future development, with the aim of providing essential scientific guidance for advancing material science and technology through ML.Highlights Machine learning can address complexity in constitutive model of the anisotropic composites. Machine learning predicts mechanical properties of composites well by process and structure. Machine learning enhances efficiency in inverse design to optimize composites. Limitations, challenges, development trends of ML in composites.

Effect of Fe Element and Ultrasonic Vibration on the Microstructure and Mechanical Properties of the Cu-TiB2 Composites

Cu-(Fe-Ti)-TiB2 composites were prepared by in situ reaction and vacuum casting with and without ultrasonic vibration. The evolution of the microstructure and mechanical properties of the composite with the variation in Fe element was analyzed. The import of Fe elements could purify the matrix after in situ reaction and the formation of a nanoprecipitated phase, thus improving the strength of Cu-Fe-Ti-TiB2 composites. Meanwhile, compared with the traditional casting process, the Cu-Fe-Ti-TiB2 composites with ultrasonic vibration treatment exhibit uniform TiB2 particle distribution and better properties. The tensile strength and uniform elongation of the composite with a Fe content of 0.7 wt.% reached 511 MPa and 6.02%, increasing by 14.3% and 318% compared to the unalloyed composite, respectively. The tensile strength and uniform elongation of Cu-0.7Fe-Ti-TiB2 composite with ultrasonic vibration treatment increased to 533 MPa and 7.16%, respectively. The TiB2 microscale particles and Fe2Ti nanoscale precipitates with uniform distribution effectively impeded dislocation movement and recrystallization, which improved the tensile strength and stability at elevated temperatures.

Effect of benzoyl chloride treatment on morphological, thermal, mechanical, and hydrothermal aging properties of date palm/polyvinyl chloride (PVC) composites

The use of natural fibers has seen a significant rise in the composites sector, resulting in the creation of polymer composites with exceptional strength. These environmentally-friendly alternatives offer a compelling substitute for synthetic composites. This study explores the use of date palm waste as reinforcement for the fabrication of polyvinyl chloride (PVC) composites. A surface modification method was essential for improving the binding interaction between palm fibers and PVC composites. The two-hour benzoyl chloride treatment at 140 °C played a crucial role. The study examined the effects of hydrothermal aging on mechanical properties of composites, using various techniques such as surface morphology analysis, Fourier Transform Infrared spectroscopy, and Thermogravimetric Analysis, on composites made of untreated fibers and those treated with benzoyl chloride. Although the treatment of palm fiber-reinforced composites with benzoyl chloride improved their mechanical properties, it is crucial to note that hydrothermal aging reduced their tensile strength by 10%. Despite this, these composites prove to be well-suited for applications requiring moderate strength and stiffness in mild environmental conditions. These composites, while utilizing benzoyl chloride for surface treatment, still represent a more sustainable alternative to traditional synthetic composites by incorporating renewable date palm waste and enhancing mechanical properties, which potentially reduces overall environmental impact.

Microstructure evolution and mechanical property of B4C/Ti65 composites via laser directed energy deposition

Application of laser additive manufacture technique to fabricate the discontinuous reinforced high-temperature titanium matrix composites found its great potential in the complex components of aerospace industry. This work prepared the B4C/Ti65 composites by laser directed energy deposition (LDED) with special attention paid to the relationship between microstructure and mechanical property of composites. The microstructure of B4C/Ti65 composites under different laser power and B4C content were investigated, based on which the tensile strength and ductility evolution and the underlying strengthening mechanism of the B4C/Ti65 composites were discussed. The submicron TiBw were randomly distributed in the composites with additions of 0.1 wt% and 0.2 wt% B4C. The TiBw and TiCp in the composites with addition of 0.3 wt% B4C exhibited a uniform distribution rather than distributed along the prior β grain boundaries at high laser power. There existed the network structure of TiBw and TiCp in the 0.5 wt% B4C/Ti65 composites. TiCp always adhered to TiBw, and both TiBw and TiCp acted as the nucleation sites for equiaxed α grain, which is responsible for the finer α colonies that benefit to strength with higher B4C content. The tensile tests showed that the 0.3 wt% B4C/Ti65 composite shows a good combination of ultimate tensile strength (1201 MPa) and elongation (5.54 %). The grain refinement strengthening played the dominant role in the strength increment of the B4C/Ti65 composites. In addition, the formation of clustered submicron-TiBw and network structure of TiBw and TiCp in the 0.5 wt% B4C/Ti65 composites greatly upgraded the yield strength.

Data-driven bio-mimetic composite design: Direct prediction of stress–strain curves from structures using cGANs

Designing high-performance composites requires integrating tasks, including material selection, structural arrangement, and mechanical property characterization. Accurate prediction of composite mechanical properties requires a comprehensive understanding of their mechanical response, particularly the failure mechanisms under high deformations. As traditional computational methods struggle to exhaustively explore every composite configuration in the vast design space for optimal design search, machine learning offers rapid identification of optimal composite designs. This study presents a cGAN-based deep learning model for predicting stress–strain curves directly from composite structures using an image-to-vector approach. The model incorporates fully connected layers within a U-Net generator for stress–strain curve generation and utilizes a PatchGAN discriminator for realism assessment. This end-to-end mapping from structures to mechanical response effectively eliminates the need for extensive simulations and labor-intensive post-analyses. Phase-field simulations were conducted to model the material failure process, generating stress–strain curves for various composite structures used as ground truth data to train and test the surrogate model. This study incorporates various composite structures in the dataset, including random (RS), layered (LS), chessboard-like (CS), soft-scaffold (SS), and hard-scaffold (HS), enhancing the representation of design diversity. Despite being trained on a limited dataset (approximately 1.5% for each bio-mimetic structure and 10−72% for RS composites), the model achieves highly accurate predictions in stress–strain curves, with MAE loss converging to 0.01 for training and 0.05 for testing after 2 million iterations. High evaluation scores on training data (R2>0.997, MAPE <1.08%) and testing data (R2>0.946, MAPE <5.53%) demonstrate the model’s accuracy in predicting mechanical properties such as Young’s modulus, strength, and toughness across all composite structures. Overall, the study provides a proof of concept for using machine learning to simplify the design process, demonstrating its potential for solving inverse composite design problems.

Effect of aging temperature on microstructure and mechanical properties of (Ti1400+TiC)/Ti6Al4V composites

Titanium matrix composites, due to their high strength, high modulus, and high temperature resistance, have become ideal materials that meet the lightweight and high-performance requirements in the aerospace industry. However, their poor ductility remains a key issue that restricts their widespread application. In this study, (Ti1400+TiC)/TC4 composites were prepared by low-energy ball milling and spark plasma sintering and subjected to solution treatment and aging treatment. The effects of aging temperature on the composition, microstructure, and mechanical properties of the composites were analyzed, and the strengthening mechanism of (Ti1400+TiC)/TC4 composites was discussed. The aging temperature between 350 ℃ and 700 ℃ had little effect on the microstructure of TC4 matrix and the discontinuous three-dimensional network structure of TiC particles. As the aging temperature increased, the elongated α-phase within the Ti1400 region became shorter and thicker, and Cr’s rapid diffusion resulted in β-phase being more widely distributed. After aging at 600 ℃, the tensile strength of the composite was 1202 MPa, and its total elongation reached 11.3 %, showing excellent strength-plasticity matching. The mechanical properties of composites are mainly affected by the microstructure in the Ti1400 region. The elongated α-phase in the Ti1400 region provides high strength for the composite. The thicker α-phase and the widely distributed β-phase led to more uniform strain within the composite, avoiding premature fracture caused by stress concentration near TiC particles and promoting ductility in the composite.

Synthesis of rice‐granular bimetallic nickel/iron phyllosilicates to simultaneously lubricate and strengthen the epoxy‐based composites

AbstractTo improve the subpar lubricating performance of epoxy resin, this paper presents the preparation of a novel bimetallic phyllosilicate featuring a distinctive rice‐granular morphology, which incorporates nickel and iron metal cations through a facile hydrothermal process. These phyllosilicates were then integrated into the epoxy matrix to form composites. A comprehensive analysis of the target product validates the rationality of the synthesis strategy for the as‐prepared rice‐granular bimetallic nickel/iron phyllosilicate, demonstrating a homogeneous hierarchical structure with numerous tiny nanosheets of nickel/iron phyllosilicate grown in situ on the flat surfaces of the rice‐granular metal–organic frameworks. An adequate addition of nickel/iron phyllosilicates allows for excellent dispersion within the matrix and establishes strongly bonded interfaces, steadily increasing the elastic modulus and hardness. Notably, the average friction coefficients decrease from 0.515 for the pure resin to 0.450 for the composites when the filler content reaches 7%, indicating a significant solid lubrication effect. In contrast, adding just 1% nickel/iron phyllosilicate moderately improves wear resistance, elongation at break, and tensile strength. Furthermore, it was found that as the filler content increased, the weight loss rate was reduced by approximately 43.8%, while the residual char increased by 74.2%, significantly enhancing the thermal stability of epoxy composites at high temperatures. This study offers a promising approach to preparing self‐lubricated epoxy composites with favorable mechanical and thermal properties.Highlights NiFePS was successfully synthesized via a facile two‐step self‐polymerization. Excellent mechanical properties of composites could be achieved with low content of NiFePS. The friction coefficient and wear rate were lowered remarkably. The friction mechanism was solid lubrication.

Integrated design of flame retardancy, smoke suppression and structure of carbon fiber reinforced vinyl ester resin composites through intercalation of nanofiber membranes

A novel flame-retardant method based on the intercalation of nanofiber flame-retardant membrane has been studied for composite laminates. Compared to traditional additive flame-retardant method, this method is more efficient, does not affect the composite forming process, and can improve the mechanical properties of composite. Nanofiber flame-retardant membranes (FPm) are prepared from polyether sulfone (PES) and pentaerythritol phosphate ester (PEPA) by electrospinning technique and inserted in the interlayer of carbon fiber reinforced vinyl ester resin (CF/VER) composites. The FPm can improve the flame-retardancy and smoke suppression of the CF/VER composites by promoting the charring of interlayer structure and form a barrier layer. The thickness of the FPm and the flame-retardant performance of the composites are positive correlation. At a FPm’s thickness of 50 μm, the limiting oxygen index (LOI) and UL-94 ratings of the CF/VER composites reached 33.5 % and V-1, respectively. The total heat release (THR) and total smoke release (TSP) are reduced by 26.4 % and 30.4 %, respectively. Due to the interlayer enhancement effect of FPm, the mechanical strength and interlaminar fracture toughness of CF/VER composites are also improved. Especially, when the thickness of FPm is 30 μm, the mode I interlaminar fracture toughness (GIC) of the CF/VER composite increased by 17.4 %. while the flexural strength, interlayer shear strength (ILSS), mode II interlaminar fracture toughness (GIIC) and storage modulus (E’) are all enhanced.

Strong and Fatigue-Resistant Carbon Nanotube Composites Enabled by Amorphous/Crystalline Heterophase Shell.

Lightweight materials with high strength and long cyclic lifespan are greatly demanded in practical applications, yet these properties are usually mutually exclusive. Here, we present a strong, lightweight, highly deformation-tolerant, and fatigue-resistant carbon nanotube (CNT) composite enabled by an amorphous/crystalline heterophase carbon shell. In particular, we obtain nanocrystallites with CNT-induced crystalline orientation uniformly embedded within an amorphous matrix by controlled thermal annealing. The heterophase carbon shell effectively alleviates the stress concentration and inhibits crack propagation, which renders our composite superior mechanical properties and high fatigue resistance (106 compression cycles at 20% strain with high stress of 144 kPa, or 5 × 105 cycles at 50% strain with stress up to 260 kPa). This study provides a deep understanding of amorphous-crystalline phase transition and insight into utilizing phase engineering to design and develop other high-performance functional materials such as structural materials and catalysis.

Microstructure evolution and mechanical properties of a lamellar AlCoCrFeNi2.1 eutectic high-entropy alloy processed by high-pressure torsion

High-pressure torsion (HPT) was applied to a lamellar eutectic high-entropy alloy (EHEA) to study the effect of severe plastic deformation (SPD) on the composite structure and mechanical properties. We found that the existence of multiple phases affects defect distribution and the fragmentation process during HPT. Structural evolution shows orientation dependence with respect to the shear plane, which finally leads to a refined multiphase structure with nanograins and vortex clusters after a shear strain γ of 24. In nanograins, dislocation-mediated deformation prevails. The high density of grain boundaries, forest dislocations, and the generation of deformation twins restrict dislocation movement. As a result, an EHEA with a yield strength of 1.75 GPa, an excellent tensile strength of 2.20 GPa, and an appreciable failure strain of 5 % is realized. Our results demonstrate that the HPT deformation process of the lamellar EHEA is significantly affected by the structure. SPD on the multiphase structure is a suitable route for designing high-strength yet ductile alloys.

Micromechanical response of graphene coating on nt-TiAl under nanoindentation

The nanoindentation response of graphene (Gr) coating on nanotwin titanium-aluminum (nt-TiAl) matrix composites was studied using molecular dynamics (MD) simulation. The indentation velocity, twin boundary spacing, and parallel and vertical Z-axes are studied. The results show that the bearing capacity and hardness of Gr coating is significantly higher than that after coating failure, and the load-displacement curve shows the same phenomenon. Damage to the substrate material at varying speeds is indicated by atomic aggregation near the Gr coating, with the center of aggregation showing a negative correlation with indentation velocity. The matrix's damaged area is larger when the twin layer is perpendicular to the Z-axis and deeper when parallel, showing that the twin structure limits material damage by hindering dislocation expansion. Moreover, the presence of Gr coating delayed the matrix's plastic deformation process. This delay effect significantly improves the mechanical properties of composites, which have potential applications in aerospace.

Influence of nanofiller surface treatment on mechanical properties of pyrolyzed ceramic nanocomposites

The brittleness and limited plastic deformation of ceramics restrict their applications. In this work, the effects of pristine (CNTP), functionalized (CNTOH, CNTCOOH) and silanized MWCNTs on the mechanical properties of Silicon Carbide obtained by pyrolyzing polycarbosilane SMP-10 were studied. Functionalization with 3-glycidoxypropyltrimethoxy was analyzed through dispersion stability, zeta potential, and EDS analyses, revealing increased silicon content and colloidal stability in silanized MWCNTs. However, silanized MWCNTs led to reduced mechanical properties in composites, while untreated MWCNTs (CNTP, CNTOH, CNTCOOH), showed a substantial increase in modulus by 74.2 %, 86.9 %, and 30.5 %, respectively. The observed enhancement in mechanical properties exceeded the outcomes predicted by the rule of mixtures, suggesting notable morphological changes induced by MWCNTs. Potential underlying factors including toughening mechanisms and changes in porosity were evaluated and discussed in depth. Composites with untreated MWCNTs showed nearly a two-fold increase in fracture toughness. This work shows a streamlined approach for the development of ceramic nanocomposites (CNCs), achieving significant improvement in mechanical properties through pyrolysis, surpassing traditional methods reliant on densification processes. These findings demonstrate the substantial potential of CNCs, enhancing their suitability for advanced engineering applications.

Oil Plant Pomace as a Raw Material in Technology of Sustainable Thermoplastic Polymer Composites

The design of composites offers extensive opportunities for controlling parameters and utilizing diverse materials, including those sourced from recycling or waste streams. In this study, biocomposites were developed using high-density polyethylene (HDPE) and pomace derived from oilseed plants such as evening primrose, gold of pleasure, rapeseed, and sunflower seeds, mixed in a 1:1 ratio. These biocomposites were evaluated for their structural, mechanical, morphological, and thermal properties, as well as their vulnerability to overgrowth by cellulolytic fungi. The results indicate that incorporating plant waste into HDPE reduces thermal stability while increasing water absorption and thickness swelling. Additionally, the biocomposites showed enhanced fungal growth, which may improve their biodegradability. Notably, the PE_EP composite, derived from evening primrose pomace, did not show significant differences in surface roughness and MOE parameters compared to pure polyethylene. In the case of PE_R composite, an increase in MOE was observed while maintaining the MOR parameter compared to pure PE. Although generally the mechanical properties of composites were lower compared to pure polyethylene, the findings suggest that with further optimization, oil plant pomace can be a valuable raw material for producing biocomposites suitable for various industrial applications, thereby contributing to sustainability and effective waste recycling.

Comparative study of oil palm and nettle fibers reinforced chemically functionalized high‐density polyethylene composites

AbstractThe demand of natural fiber reinforced composites has grown enormously in polymer industries owing to their renewability and sustainability and maintaining their performance and properties. In this investigation, two natural fibers have been considered as a reinforcer to develop chemically functionalized high‐density polyethylene (CF‐HDPE)‐based composites. The total holocellulose content of ~85% and ~65% for nettle fiber (NTF) and oil palm empty fruit bunch fiber (OPF) make them significant for this study. OPF/CF‐HDPE and NTF/CF‐HDPE composites have been developed and characterized to measure their desirable properties. The structural confirmation suggests reinforcement/matrix adhesion through ester and hydrogen bonds between them. NTF/CF‐HDPE and OPF/CF‐HDPE are thermally stable upto 240°C and 250°C, respectively. A significant increment of ~40% and ~64% in tensile strength were observed in addition of OPF and NTF reinforcer in pristine matrix. A similar observation has been shown in flexural strength with improvement of ~58% and ~83% with OPF and NTF as reinforcer. Among all these composite compositions, the 30/70 NTF/CF‐HDPE composite demonstrated the highest tensile and flexural properties values due to higher holocellulose of NTF. This study demonstrates the potential of OPF and NTF reinforcer to develop natural fiber reinforced polymer composites, which helps respective industries to manufactured tailored made products with desirable properties.Highlights OPF/CF‐HDPE and NTF/CF‐HDPE composites are sustainable and low cost. The composite compositions have been developed by extrusion and injection molding. The composite's mechanical (tensile and flexural) properties have been demonstrated. SEM and FTIR characterized the composites for the fiber/matrix adhesion. The composite's thermal stability has been affected by fibers and matrix.

Synergistic modification of continuous fiber reinforced Nylon‐6 composites with nano calcium carbonate and polyurethane

AbstractContinuous fiber reinforced Nylon‐6 composites with high strength have been widely used in automotive, wind turbine blades, aerospace, and military fields. Here, we present a synergistically reinforced strategy to enhance the mechanical properties of the continuous glass‐fiber reinforced Nylon‐6 (CGF/PA6) and basalt‐fiber reinforced Nylon‐6 (CBF/PA6) composites via in‐situ polymerization, simultaneously employing thermoplastic polyurethane (TPU) and modified calcium carbonate (M‐CaCO3) as the toughening and strengthening materials. The micro‐morphology, mechanical properties, thermostability, water absorption, and flowability of composites are investigated. Significantly, the synergistic effect of TPU and M‐CaCO3 can improve mechanical properties, thermal stability (335.6 and 396.5°C in the T50%), and flowability (43.02 and 40.56 g/10 min) of the modified continuous glass‐fiber reinforced Nylon‐6 (M‐CGF/PA6) and basalt‐fiber reinforced Nylon‐6 (M‐CBF/PA6) composites, especially the high tensile strength (96.07 and 217.43 MPa) and impact strength (95.03 and 206.36 kJ/m2) which increases by 8.53% and 5.18% for the tensile strength and 91.25% and 100.27% for impact strength compared with the unmodified CGF/PA6 composites and CBF/PA6 composites. This work provides theoretical support for continuous fiber reinforced Nylon‐6 composites.Highlights Continuous fiber reinforced Nylon‐6 Composites is prepared by in situ polymerization. In situ polymerization is beneficial to the good impregnation of continuous fibers and uniform dispersion of modified calcium carbonate (M‐CaCO3). The modified continuous fiber can improve the interfacial bonding properties of composites. The TPU and M‐CaCO3 synergistically reinforce the mechanical properties of composites. The M‐CaCO3 nanoparticles are uniformly dispersed in the composites.

Improvement of interfacial adhesion of aramid fiber/polycarbonate composites by surface modification with graphene oxide modified sizing agents

AbstractVarious sizing agents were prepared to enhance the interfacial properties between aramid fiber (AF) and polycarbonate (PC), as well as to enhance the mechanical properties of AF/PC composites. It was found that PC sizing agent, P‐GO sizing agent, and PSi‐GO sizing agent effectively coated the surface of AF from the FTIR and XPS and SEM results. The IFSS and mechanical properties of composites reinforced with fibers treated by the sizing agents exhibited significant improvement, as well as their single fiber tensile strength also improved. Specifically, when AF was treated with PSi‐GO sizing agent, the interfacial shear properties between AF and PC increased by a remarkable 78.69%, reaching 22.89 MPa compared to the original AF/PC composite, the tensile strength of the single‐filament exhibited an increment of 12.4% to 26.4 cN/dtex. Moreover, the tensile strength, flexural strength, and impact strength of the composite increased by 5.43%, 77.74%, and 54.71%, respectively. These improvement can be attributed to the GO with a higher concentration of chemical groups and excellent dispersion with modified with the silane agent. These findings suggest that coating the AF with sizing agents can effectively enhance its interfacial adhesion with the matrix, which is useful for its application as the reinforcement in the composites.Highlights Adding GO to the sizing agent to change the Aramid fabric surface properties. Silane coupling agent was used to improve the dispersion of GO on the fiber surface. GO modified sizing agent can improve the flexural strength, tensile strength, and interlaminar shear strength of the composites.

In situ growth of silver nanoparticles on carbon fiber by plasma–liquid interaction to improve performance of epoxy composites

Grafting nanomaterials on the carbon fiber (CF) surface is considered an effective strategy for enhancing the interfacial properties of CF-reinforced polymer composites (CFRPs). However, the mechanical properties of the CFs are often compromised during treatment. A new method for in situ growing silver nanoparticles (AgNPs) on the CF surface is proposed in this study. The CFs are first immersed in a low-viscosity silver nitrate solution to form a thin liquid film on the surface. Subsequently, using the abundant active particles in the plasma, the silver ions are reduced to silver atoms and grown into AgNPs on the CF surface. The tensile strength of CF@Ag was 38.74% greater than that of untreated CF, potentially due to the reparative action of AgNPs on defects in CF. The CF showed an evident improvement in surface wettability because of the AgNPs. Furthermore, the interfacial properties were noticeably improved, with the interfacial shear strength of CF@Ag increasing to 91.59 MPa, which was about twice that of pristine CF. Thus, the mechanical properties of composites are significantly improved (flexural strength increased by 190.74%). This study presents a non-destructive and convenient method for growing nanoparticles onto CF to establish a robust interface in CFRPs.

Mechanical Properties of Additive-Manufactured Composite-Based Resins for Permanent Indirect Restorations: A Scoping Review.

The introduction of 3D printing technology in dentistry has opened new treatment options. The ongoing development of different materials for these printing purposes has recently enabled the production of definitive indirect restorations via 3D printing. To identify relevant data, a systematic search was conducted in three databases, namely PubMed, Scopus, and Web of Science. Additionally, a manual search using individual search terms was performed. Only English, peer-reviewed articles that encompassed in vitro or in vivo research on the mechanical properties of 3D-printed composite materials were included, provided they met the predefined inclusion and exclusion criteria. After screening 1142 research articles, 14 primary studies were selected. The included studies mainly utilized digital light processing (DLP) technology, less commonly stereolithography (SLA), and once PolyJet printing technology. The material properties of various composite resins, such as VarseoSmile Crown Plus (VSC) and Crowntec (CT), were studied, including Vickers hardness, flexural strength, elastic modulus, compressive strength, tensile strength, fracture resistance, and wear. The studies aimed to compare the behavior of the tested additive composites to each other, conventional composites, and subtractive-manufactured materials. This scoping review examined the mechanical properties of composites used for 3D printing of definitive restorations. The aim was to provide a comprehensive overview of the current knowledge on this topic and identify any gaps for future research. The findings suggest that 3D-printed composites are not yet the first option for indirect restorations, due to their insufficient mechanical properties. Due to limited evidence, more research is needed in this area. Specifically, there is a need for clinical trials and long-term in vivo research.

Chemical Modification of Wood Waste for the Production of Composite Materials as a Prospective Solution to the Recycling Issue

The issue of increasing the physical and mechanical properties of composites by modifying the wood is considered. To improve the quality and increase the resistance of wood filler to various influences, the acetylation has been proposed, which is carried out aiming to introduce the acetyl groups into the composition of wood by replacing free hydroxyl radicals. The effectiveness of acetylation as a method of modifying wood filler in the production of composite materials in order to improve their physical and mechanical properties (dimensional stability, hydrophobicity and biostability) has been experimentally confirmed.