Changes In Roughness Research Articles

Characterization of Wear Patterns in Gun Barrel’s Throat Region Using Forensic Microscope: Insights Into Long-Term Effects of High-Pressure Gas Exposure

Objectives: This research aims to explore the damage sustained by the gun barrel's throat region over a long period of use, shedding light on the wear characteristics, and providing valuable insights into the long-term effects of high-pressure gas exposure during firing. Methods: To achieve this objective, the appearance of the gun barrel's throat region was characterized using forensic microscopy techniques. Visual and microscopic examinations were conducted on five (5) gun barrels with ten years or less of service usage and five (5) gun barrels with over ten years of service usage from the Philippine National Police to assess the degree of wear in the barrel’s throat region. Findings: The findings revealed varying degrees of wear in the barrel throat regions. Firearms with 10 years or less of service usage exhibited moderate corrosion, narrow cracks, and minimal soot particle presence while firearms with over 10 years of service usage showed severe corrosion, deep cracks, scattered potholes, superficial scraped surfaces, and heavy soot particle presence. Novelty: This research contributes to the understanding of barrel performance, maintenance, and potential hazards associated with aging firearms, thus providing novel insights into the long-term effects of high-pressure gas exposure during firing. By examining the changes in material properties and surface roughness of the gun barrel’s throat region, this study seeks to improve the understanding of how repeated firing impacts gun barrel performance and longevity. This, in turn, may aid in developing future maintenance practices to enhance firearm durability and safety. Keywords: Gun Barrels, Wear Characteristics, Gun Barrel Throat Region, High-Pressure Gas Exposure, Wear Patterns

Improved ferroelectricity and endurance in Ca doped Hf0.5Zr0.5O2 films

Doped Hf0.5Zr0.5O2 materials have drawn increasing attention due to the excellent ferroelectric properties, but the relevant research is just in the preliminary stage and the reported doped systems are rare. In this work, Ca doped Hf0.5Zr0.5O2 (Ca:HZO) ferroelectric films were successfully fabricated via chemical solution deposition and investigated for the first time. It is observed that Ca doping induces a phase transformation from monoclinic to orthorhombic/tetragonal and then to monoclinic/tetragonal. The highest orthorhombic phase fraction is achieved in 2.5 mol% Ca doped HZO film, contributing to the optimum ferroelectric property with the largest remnant polarization of 14.00 μC/cm2 after 105 cycles. Additionally, the leakage current density is observed to decrease with increasing Ca content, which is mainly associated with the changes of grain size and surface roughness. As a result, the endurance is significantly improved in the Ca doped films, and an excellent endurance of 1010 cycles is achieved in the 2.5 mol% Ca doped film. These results suggest that Ca doping can enhance the ferroelectric and endurance properties of HZO films by optimizing the phase and morphological structure.

The microhardness, morphology and tribological property of TC4 subjected to machine hammer peening

Ti alloy has become an indispensable material in harsh working environments due to its excellent wear resistance, corrosion resistance and impact resistance. These environments place stringent requirements on the fatigue life, friction and wear, and surface strength of materials. Therefore, this study aims to deeply explore the surface mechanical properties of Ti-6Al-4V (TC4) alloy after machine hammer peening (MHP) treatment. By conducting experiments on TC4 alloys treated with different hammering energies, the changes in surface hardness, morphology, roughness, tensile properties, and friction properties were analyzed, and the strengthening mechanism of MHP was discussed. Experimental results show that MHP treatment can effectively improve the surface properties of TC4. With the increase of hammer energy, due to the double-sided hammering of the plate, the microhardness first increases, then decreases, and then rises again. The tensile strength and yield strength of the sample increase slightly, but the elongation at break decreases. The surface roughness of the sample increases first and then decreases. Similarly, after MHP treatment, the wear resistance of the samples increased, the friction coefficient decreased, and the wear amount and surface height difference showed a trend of first increasing and then decreasing. The wear mechanism mainly included adhesive wear, abrasive wear and fatigue wear.

Evolution of Turbulent Boundary Conditions on the Surface of Large Barchan Dunes: Anomalies in Aerodynamic Roughness and Shear Velocity, Aeolian Threshold, and the Role of Dune Skewness

AbstractWe recorded aerodynamic roughness and shear velocity along transects on and around mature crescent‐shaped barchan dunes of and height above the horizontal rock‐covered Qatar desert by fitting to the log‐law time‐averaged vertical velocity profiles acquired from triads of ultrasonic anemometers penetrating the inner turbulent boundary layer. Shear velocity first decreased, then recovered as air climbed on the dune, with a local maximum ahead of the crest as predicted by the Jackson and Hunt (1975, https://doi.org/10.1002/qj.49710143015) theory. Unlike flows over gentler bedforms without a slope discontinuity, an anomalous peak of shear velocity also arose on the dune centerline at the brink, which the theory attributed to skewness in the dune transect profile. The onset of aeolian transport produced a log‐law passing through the Bagnold (1941, https://doi.org/10.1007/978‐94‐009‐5682‐7) focal point. It was bracketed by noticeable hysteretic peaks in the correlation between wind speed and entrained sand flux. The dunes' rocky surroundings and topography produced an aerodynamic roughness at odds with the Nikuradse (1933, https://ntrs.nasa.gov/citations/19930093938) data for fully developed turbulent boundary layers. Large‐eddy numerical simulations illustrated the sensitivity of shear velocity to wide changes in aerodynamic roughness from desert floor to dune surface.

Electro-Mechanical Behavior of Copper-Based Electrical Motor Brushes

This study was mainly performed in order to examine the properties of electric motor brushes (EMB). EMBs are electrically conductive and work under wear conditions due to direct contact with the moving part (rotor) of electric motors. In accordance with the scope of the study, EMB characteristics were investigated in two different groups and reproduced with a new technique at the end of this phase. New EMBs were produced via varying proportions of copper matrix, graphene, and silicon carbide reinforcements. The composite-alloy powder elements were carefully squeezed by a cold and single-axis hydraulic press under a pressure of 500 MPa (±5 MPa) following 8 hours of mechanical alloying (MA). The molded composite product (sample) was sintered at 900° C for 1 hour in a reducing gas atmosphere. 100 kPa spring pressure was tested on each sample thrice with 8, 16, 24, and 32 m/s rotational speeds and densities of 4, 8, 12, and 16 A/cm2. Following this process, the electrical conductivity, porosity, hardness, wear loss, surface roughness, and temperature changes were investigated for each sample. It was determined that the electrical conductivity decreased with increasing reinforcement ratio and, in terms of electrical conductivity, affected the brushes’ properties negatively.

The impact of Streptococcus mutans biofilms on the color stability and topographical features of three lithium disilicate ceramics.

Secondary caries around ceramic restorations is the most common reason for the replacement of fixed dental prostheses (FDPs). Therefore, it is important to examine the susceptibility of different ceramic materials to biofilm formation. This study aimed to evaluate biofilm development and associated roughness and color alterations in three lithium disilicate ceramics: Emax CAD (EC), Emax Press (EP), and LiSi Press (LP). Streptococcus mutans biofilms were grown on the three ceramics (n = 10 per group) for 7 days. Surface roughness values and color alteration were assessed before and after the biofilm using a non-contact profilometer and spectrophotometer, respectively. Biofilm growth was evaluated using colony-forming units (CFUs) and scanning electron microscope (SEM) images. The data were analyzed using one-way ANOVA and Tukey tests. There was a significant (p≤0.001) growth of S. mutans colonies on EC (6.75 ± 0.56) and EP (6.72 ± 0.54) specimens compared to LP, which showed no biofilm growth. The change in average surface roughness (∆Ra, nm) was significantly lower (p < 0.001) in the EC specimens (0.029 ± 0.003) compared to the EP (0.055 ± 0.012) and LP (0.041 ± 0.010). When the changes in the Rv and Rt values were investigated, no significant difference was observed among the groups. Following the biofilm challenge, the change in color (∆E00) was significantly lower (p = 0.005) in the LP group (1.68 ± 1.45) compared to the EC group (3.89 ± 1.50) and no significant difference was observed between the EP group (2.74±1.01) and the other two ceramics (p ≥ 0.05). LP ceramics exhibited superior resistance to S. mutans biofilm formation and associated changes in surface roughness and color compared to the Emax CAD and Emax Press ceramics. These findings suggest that the LiSi Press material may be more favorable to mitigate the risk of secondary caries.

Effects of Covid-19 Preoperative Mouthrinses and Different Beverages and on Surface Alteration of Polyetheretherketone (PEEK)

Objectives: to compare the color change and surface roughness of polyetheretherketones (PEEK) immersed in various beverages and mouthrinses for 7 days. Methods: the specimens were divided into 6 groups, 10 pieces per group, and each group was immersed in different solutions as followed: coffee, cola, red wine, distilled water, 0.5% povidone iodine, and 1% hydrogen peroxide. A color change (∆E*ab) was measured in each sample before and after 7 days of immersion in different solutions. At a significance level of 0.05, color change data were analyzed using one-way ANOVA and pairwise comparisons with the Games-Howell method, and surface roughness changes were analyzed using the Wilcoxon Sign-Rank test. Results: immersion of PEEK in 0.5% povidone iodine caused the most color change, followed by red wine when continuously immersed for 7 days. However, immersion in different types of solutions did not affect the surface roughness of PEEK. Conclusions: After 7 days of immersion, 0.5% povidone iodine and red wine caused color change in PEEK with no change in surface roughness

Change in Surface Roughness on the Inner and Outer Surfaces of the Microtube during Hollow Sinking.

Hollow sinking experiments and tensile tests were conducted to clarify the evolution of surface roughness during hollow sinking. Stainless steel tubes (outer diameter: 1.5 mm; wall thickness: 0.045 mm) featuring a single grain spanning the wall thickness achieved via annealing as the starting material. The tube was drawn without an internal tool using a draw bench by controlling the tube drawing speed ratio of the die entrance and exit sides. The surface roughnesses of the inner and outer surfaces at the die entrance and exit sides of the drawn tube were compared with the surface roughnesses of the inner and outer surfaces under the uniaxial tensile deformation of the starting material. As a result, two major findings were revealed; the surface roughness formation behavior during the hollow sinking; the uniaxial tensile deformation exhibits a tube on both sides of the entrance and the exit of a die. Former uniaxial tensile deformation forms surface roughness of the tube at the die-entrance-side. However, hollow sinking reduces the roughness. The tube keeps its small roughness even though it is applied the later uniaxial tensile deformation behind the die exit. Furthermore, the conventional formula to predict the surface roughness of a metal sheet caused by the uniaxial tensile deformation can predict the surface roughness of a tube in the hollow sinking. At both die entrance and exit sides, the roughness of the inner surface was larger than that of the outer surface at the die entrance and exit side. The outer surface of the tube contacts the inside of a die when the tube passes through the die. The height of the convex parts decreased at that moment. Hollow sinking suppressed the increase in surface roughness of the inner surface as the outer surface was smoothed in the die. However, due to the formation of surface roughness after leaving the die, there is an overall increasing trend in inner surface roughness.

Effect of different approaches of direct radiation on the surface structure and caries susceptibility of enamel

It is not clear whether different radiation methods have different effects on enamel. The purpose of this study was to compare the effects of single and fractionated radiation on enamel and caries susceptibility and to provide an experimental basis for further study of radiation‑related caries. Thirty-six caries-free human third molars were collected and randomly divided into three groups (n = 12). Group1 (control group) was not exposed to radiation. Group 2 received single radiation with a cumulative dose of 70 Gy. Group 3 underwent fractionated radiation, receiving 2 Gy/day for 5 days followed by a 2-day rest period, for a total of 7 weeks with a cumulative dose of 70 Gy. Changes in microhardness, roughness, surface morphology, bacterial adhesion and ability of acid resistance of each group were tested. Scanning electron microscope revealed that the enamel surface in both radiation groups exhibited unevenness and cracks. Compared with the control group, microhardness and acid resistance of enamel decreased, while roughness and bacterial adhesion increased in both the single radiation and fractionated radiation groups. Compared with the single radiation group, the enamel surface microhardness and acid resistance decreased in the fractionated radiation group, while roughness and bacterial adhesion increased. Both single radiation and fractionated radiation resulting in changes in the physical and biological properties of enamel, with these changes being more pronounced in the fractionated radiation group. Therefore, fractionated radiation is recommended as a more suitable method for constructing a radiation‑related caries model in vitro.

Influence of Laser Power and Rotational Speed on the Surface Characteristics of Rotational Line Spot Nanosecond Laser Ablation of TC4 Titanium Alloy.

The TC4 titanium alloy is widely used in medical, aerospace, automotive, shipbuilding, and other fields due to its excellent comprehensive properties. As an advanced processing technology, laser processing can be used to improve the surface quality of TC4 titanium alloy. In the present research, a new type of rotational laser processing method was adopted, by using a beam shaper to modulate the Gaussian spot into a line spot, with uniform energy distribution. The effects of the laser power and rotational speed on the laser ablation surface of the TC4 titanium alloy were analyzed. The results reveal that the melting mechanism of the material surface gradually changes from surface over melt to surface shallow melt with the increase in the measurement radius and the surface roughness increases first, then decreases and, finally, tends to be stable. By changing the laser power, the surface roughness changes significantly with the variation in the measurement radius. Because low laser power cannot provide sufficient laser energy, the measurement radius corresponding to the surface roughness peak of the microcrack area is reduced. Under a laser power of 11 W, the surface roughness reaches its peak when the measurement radius is 600 μm, which is 200 μm lower than that of a laser power of 12 W, 13 W, and 14 W. By changing the rotational speed, the centrifugal force generated by the rotation of the specimen affects the distribution and re-condensation of the molten pool of the surface. As the rotational speed increases, the shallow pit around the pit is made shallower by the filling of the pit with molten material and the height of the bulge decreases, until it disappears. The surface oxygen content of the material increases first and then decreases with the increase in the measurement radius and gradually approaches the initial surface state. Compared with a traditional laser processing spot, the rotational line spot covers a larger processing area of 22.05 mm2. This work can be used as the research basis for rotational modulation laser polishing and has significance for guiding the innovative development of high-quality and high-efficiency laser processing technology.

CuxS films as photoelectrodes for visible-light water splitting

Copper sulfides are appealing semiconductors for optoelectronics applications requiring visible-light activity, such as solar water splitting, due to their relatively low band gaps and earth-abundance. This study investigates the effect of deposition conditions, including substrate temperature and background gas pressure, on the characteristics and photoelectrochemical performance of copper sulfide (CuxS) films grown by pulsed laser deposition (PLD) on Si (100) substrates. The results reveal that varying the deposition parameters influences the crystalline phases, morphology, and optoelectronic properties of the films. For deposition at room temperature, the films exhibited covellite CuS phase, while elevated deposition temperatures (250 °C and 500 °C) led to the formation of Cu1.8S and Cu2S phases, resulting in narrowing of the band gap, with the increased temperature also enhancing the film crystallinity and surface roughness. As a result of the changes in film morphology and crystal structure, photocurrent density magnitudes increased with higher deposition temperatures, reaching 0.747 mA/cm2 at −0.8 V for films deposited at 500 °C under vacuum, at least an order of magnitude higher than reported in comparable previous studies of the photoelectrochemical performance of CuxS. Background gas pressure only slightly affected the photocurrent density, with changes in photoactivity also correlating with changes in film roughness and band gap. The results demonstrate the good visible-light activity and behavior of CuxS as a stand-alone photoelectrode material, with tunability based on the fabrication conditions, suggesting their potential use in photoelectrochemical and other solar energy conversion applications.

Effect of a novel low-concentration hydrogen peroxide bleaching gel containing nano-sized sodium trimetaphosphate and fluoride

ObjectivesTo evaluate in vitro the effects of nano-sized sodium trimetaphosphate (TMPnano) and sodium fluoride (F) added to a 17.5 % hydrogen peroxide (H2O2) bleaching gel on the color change, enamel mechanical and morphological properties, and H2O2 transamelodentinal diffusion. Materials and MethodsBovine enamel/dentin discs (n = 180) were divided according to the bleaching gel: 17.5 % H2O2 (17.5 % HP); 17.5 % H2O2 + 0.1 % F (HP/F); 17.5 % H2O2 + 1 % TMPnano (HP/TMPnano); 17.5 % H2O2 + 0.1 % F + 1 % TMPnano (HP/F/TMPnano) and 35 % H2O2 (35 % HP). The gels were applied for 40 min on three sessions, each session spaced 7 days apart. The total color change (ΔE*ab) according to the Commission Internationale de l'Eclairage (CIE) L*a*b* color change measured by CIEDE2000 (ΔE00), whitening index (ΔWID), surface hardness (SH), surface roughness (Ra), cross-sectional hardness (ΔKHN), and transamelodentinal diffusion were assessed. Enamel surfaces were examined using Scanning Electron Microscopy (SEM) and Energy Dispersive X-ray (EDS) analysis. The data were analyzed using ANOVA, followed by the Student-Newman-Keuls test (p < 0.05). ResultsΔE*ab, ΔE00, and ΔWID values were comparable among the gels that produced a bleaching effect post-treatment (p < 0.001). The HP/F/TMPnano group exhibited lower mineral loss (SH and ΔKHN), Ra, and H2O2 diffusion compared to the 17.5 % HP and 35 % HP groups, which had the highest values (p < 0.001). SEM/EDS analysis revealed surface changes in all bleached groups, though these changes were less pronounced with F/TMPnano. ConclusionsThe 17.5 % HP gel containing F/TMPnano maintains the bleaching effect while reducing enamel demineralization, roughness, H2O2 diffusion, and enamel morphological changes. Clinical RelevanceLow-Concentration H2O2 bleaching gel containing F/TMPnano can be used as a novel approach to enhance safety and maintain the performance of aesthetic effects.

Can energy drinks affect the surface quality of bioactive restorative materials?

BackgroundsThis study aimed to compare the effects of different energy drinks on the surface roughness, weight loss, and color change of various bioactive restorative materials.MethodsCharisma Diamond One, Activa™ BioActive Restorative, Activa™ Presto™ and Equia Forte HT Fil samples were prepared using plastic molds (8 × 2 mm) (n = 10/groups). After polishing, the samples were weighed, their colors were recorded using a spectrophotometer according to the CIEDE2000 system, and their surface roughness was measured using a profilometer. The samples were immersed in Powerade, Burn, Monster and distilled water for 7 days. After immersion, all the measurements were repeated. Statistical analyses were performed using the Wilcoxon signed-rank test and the Mann‒Whitney U test (p < 0.05).ResultsAll energy drinks roughened the surface of Equia Forte HT Fil (p < 0.05). Powerade and Monster increased the Ra of all materials after 7 days (p < 0.05). Burns affected all materials except the Activa Bioactive (p < 0.05). Significant weight loss was observed in the Equia Forte group after immersion in all the energy drinks, whereas no weight loss was observed in the other groups. According to the color measurements, ΔE00 values were greater in the Burn and Monster groups, except for the Equia Forte HT Fil group (p < 0.05).ConclusionEnergy drinks affected bioactive materials to varying degrees. The glass hybrid material was the most affected, and the bioactive restorative materials based on the resin matrix were the least.

Optimizing Selective Laser Melting of Inconel 625 Superalloy Through Statistical Analysis of Surface and Volumetric Defects

This article delves into optimizing and modeling the input parameters for the selective laser melting (SLM) process on Inconel 625. The primary aim is to investigate the microstructure within the interlayer regions post-process optimization. For this study, 100 layers with a thickness of 40 µm each were produced. Utilizing the design of experiments (DOE) methodology and employing the Response Surface Method (RSM), the SLM process was optimized. Input parameters such as laser power (LP) and hatch distance (HD) were considered, while changes in microhardness and roughness, Ra, were taken as the responses. Sample microstructure and surface alterations were assessed via scanning electron microscopy (SEM) analysis to ascertain how many defects and properties of Inconel 625 can be controlled using DOE. Porosity and lack of fusion, which were due to rapid post-powder melting solidification, prompted detailed analysis of the flaws both on the surfaces of and in terms of the internal aspects of the samples. An understanding of the formation of these imperfections can help refine the process for enhanced integrity and performance of Inconel 625 printed material. Even slight directional changes in the columnar dendrite structures are discernible within the layers. The microstructural characteristics observed in these samples are directly related to the parameters of the SLM process. In this study, the bulk samples achieved a microhardness of 452 HV, with the minimum surface roughness recorded at 9.9 µm. The objective of this research was to use the Response Surface Method (RSM) to optimize the parameters to result in the minimum surface roughness and maximum microhardness of the samples.

Effect of Photoaging on the Structure, Optical Properties and Roughness of One-Shade Composite Restoratives.

The aim of the study was to evaluate changes in the degree of C=C conversion (DC%), chemical structure, optical properties and roughness of one-shade composites before/after photoaging. Τhe one-shade materials tested were Charisma Topaz One (CHT), Clearfil Majesty ES-2 Universal (MES), Essentia Universal (ESU) and Omnichroma (OMN), with G-aenial Anterior (CNA) serving as control. Specimens (2 mm thickness) were prepared and tested for DC% and chemical structure (ATR-FTIR spectroscopy), optical properties (L*a*b*-ΔΕ, translucency parameter-TP, opalescence parameter-OP, contrast ratio-CR and total transmittance-TT by UV-Vis spectroscopy) and roughness (Sa, Sz, Sdr, Sds and Sc by optical profilometry) before and after photoaging (Xe-arc weatherometer). Significant differences were found in DC% between top-bottom surfaces (ESU, OMN before; ESU, CNA after). Photoaging improved DC%, reduced ester peaks implying photodegradation, reduced L* (CHT, OMN, CNA), a* (CHT, CNA), b* (OMN, CNA), TP (all, except for MES), OP (only MES), CR (only MES, but an increase in CNA) and TT (CHT, OMN). OMN, CNA and MES demonstrated ΔΕ > 3.3. Photoaging significantly increased all roughness parameters in all materials, except for MES (Sz, Sdr, Sc) and OMN (Sdr). Although listed in the same group, significant differences were found in one-shade composites before and after photoaging. Several products were strongly affected by photoaging, demonstrating evidence of photodegradation, an increased roughness and color changes exceeding the clinically acceptable levels.

Investigation of the milled surface quality of SiCp/Al composite materials with a moderate SiCp volume fraction

Silicon carbide particle–reinforced aluminum matrix (SiCp/Al) composite materials are challenging to machine, leading to significant surface quality issues arising during milling. In this study, a single-factor experiment was conducted using carbide-coated tools to mill SiCp/Al composite materials with a 45% volume fraction of silicon carbide particles (SiCps). Scanning electron microscopy, roughness measuring instruments, and a three-dimensional optical profiler were employed to investigate the formation mechanisms of the machined surface morphologies, as well as the effects of milling parameters (milling speed, feed per revolution, and milling depth) on the surface micro-morphology of the SiCp/Al composite materials. This study assessed the suitability of various roughness characterization parameters for evaluating the milled surface of SiCp/Al composite materials, including the two-dimensional profile arithmetic mean deviation (Ra), profile root mean square deviation (Rq), and microscopic surface roughness 10-point height (Rz), as well as the three-dimensional arithmetic mean deviation of the surface profile (Sa), and root mean square deviation of the surface profile (Sq) roughness characterization parameters to evaluate the milled surface of the SiCp/Al composite materials. The findings suggest that the three-dimensional roughness characterization parameters more accurately reflected the changes in the surface roughness than the two-dimensional ones. When the milling speed increased from 0.05 to 1.2 mm/rev, Sa first decreased from 0.514 to 0.498 µm and then increased to 0.537 µm, while Sq first decreased from 0.637 to 0.616 µm and then increased to 0.658 µm. Ra, Rz, and Rq all increased with higher values of feed per revolution and milling depth.

Influence of using different toothpaste during bleaching with violet LED light (405nm) on the colour and roughness of dental enamel: an in vitro study.

This in vitro study aimed to investigate potential changes in the color and roughness of dental enamel resulting from the use of different toothpaste formulations during bleaching with violet LED light (405nm). Sixty specimens of bovine incisors, each measuring 6 × 6 × 3mm, were segregated into six distinct experimental groups based on their respective treatments (n = 10): C + VL: Brushing with Colgate® Total 12 + bleaching with violet LED; LB + VL: Brushing with Colgate® Luminous White Brilliant + bleaching with violet LED; LI + VL: Brushing with Colgate® Luminous White Instant + violet LED bleaching; C: Brushing with Colgate® Total 12; LB: Brushing with Colgate® Luminous White Brilliant; LI: Brushing with Colgate® Luminous White Instant. The examined variables included alterations in color (∆L*, ∆a*, ∆b*, ∆Eab, and ∆E00), surface roughness (Ra), and scanning electron microscopy observations. No statistically significant distinctions emerged in total color variations (∆E00 and ∆E) among the groups under scrutiny. Notably, the groups that employed Colgate® Luminous White Instant displayed elevated roughness values, irrespective of their association with violet LED, as corroborated by scanning electron microscopy examinations. It can be concluded that whitening toothpastes associated to violet LED do not influence the color change of dental enamel in fifteen days of treatment. Toothpastes with a higher number of abrasive particles showed greater changes in enamel roughness, regardless of the use of violet LED.

Atomic scale smoothing of nanoscale quartz mold using amorphous carbon films

Abstract Surface roughness control of end products is increasingly becoming significant, especially with the miniaturization trends in the semiconductor industry. Ultra-thin amorphous carbon (a-C) films offer a prime solution to optimize surface roughness due to their outstanding characteristics. In this study, hydrogenated a-C films are deposited on two-dimensional quartz plates and three-dimensional quartz molds to evaluate the growth mechanisms and changes in the surface roughness, which is supported by molecular dynamics simulations. Results reveal that surface roughness encounters multiple variations until it reaches stable values. These fluctuations are categorized into four different stages which provide a concrete understanding of various growing mechanisms at each stage. Different behavior of the atoms in the top layers is recorded in the cases of normal and grazing incidents of carbon atoms. Lower surface roughness values are obtained at low-angle deposition. Interestingly, surface smoothing is attained on the sidewalls of the nanotrench mold where the deposition occurs with high incident ion angles.

Qualitative surface roughness of lithium disilicate endo-crown for pulpotomized primary molars

Rehabilitation of pulpotomized primary molars with an appropriate restoration is essential for recovering function and safeguarding the durability of the treatment. This study aimed to assess and compare the surface roughness of stainless steel (ST) crowns, zirconia (ZR) crowns, fiberglass (FG) crowns, and lithium disilicate (LD) endo-crowns as a restoration for pulpotomized primary molars also, evaluating the surface roughness of their antagonists. Sixty pulpotomized primary mandibular first molars were used for qualitative surface roughness evaluation and divided into four groups (n = 15/group) according to the crown type (group-ST, group-ZR, group-FG, group-LD). While the other sixty sound, unprepared primary maxillary first molars were used for evaluation of their surface roughness against the tested crowns. Specimens’ preparation and cementation were carried out according to each crown type and manufacturer’s instructions. The surface roughness was done using a two-body wear test. The data were statistically analyzed. All tested crowns showed an increased change in surface roughness, except group-ZR, which had the least change in surface roughness after mechanical wear with no statistically significant difference(P = 0.681). All crown types significantly increased the surface roughness of their antagonists after mechanical wear, except group-ST which showed insignificant affection (p ≥ 0.05). Zirconia crowns and lithium disilicate endo-crowns had the least change in surface roughness compared to other groups while SSCs showed the least tooth loss in the antagonist enamel.

ТЕХНОЛОГИЧЕСКИЕ МЕТОДЫ ФОРМООБРАЗОВАНИЯ КАЧЕСТВЕННОЙ ПОВЕРХНОСТИ ДЕТАЛЕЙ ИЗ АЛЮМИНИЕВЫХ И МЕДНЫХ СПЛАВОВ

The surface quality of aluminum and copper alloy parts is studied when they are formed, which is important for transport engineering. The main task is to determine the conditions conducive to the formation of specified criteria for surface quality and to find out the dependencies of various factors when applying edge cutting machining and electrochemical processes. The research includes experimental and analytical parts, which are presented as conclusions, including the most optimal modes and conditions in terms of quality formation. The research methods are of an experimental and practical nature with the comparison and evaluation of the results obtained, in which the features of porous metal ceramics machining and methods for improving the efficiency of surface forming while maintaining the functional physical parameters of the part surfaces are considered. The novelty of the study is in finding dependencies of the obtained quality on the machining conditions and the comparative characteristics of the obtained surfaces not only in terms of changes in roughness, but also in surface porosity. As a result, recommendations are made for machining such materials, which minimize the effect of pore tightening and reduce deformation phenomena in the material.