Changes In Column Temperature Research Articles

HPLC Method Development and Validation for the Determination of Apixaban and Clopidogrel in Novel Fixed-Dose Combination Tablets

A simple, fast, and accurate high-performance liquid chromatographic (HPLC) method is developed, optimized, and validated for a fixed-dose combination of apixaban (APX) and clopidogrel (CLOP) tablets according to ICH guidelines. Chromatographic separation of the drugs was performed on a BDS Hypersil C18 (4.6 ∗ 150 mm, 5 μm), with acetonitrile (ACN) and trifluoroacetic acid (TFA) in the ratio 48 : 52 (v/v) as a mobile phase, at a flow rate of 0.9 ml/min., injection volume of 5 μL, and column temperature 45°C. The proposed method was linear over the level 25–200% for a concentration of APX 5 μg/ml and CLOP 75 μg/ml (R2 > 0.999). The detection limit for APX and CLOP was found to be 0.3465 and 3.8496 μg/ml, whereas the quantification limit was 1.0499 and 11.6656 μg/ml, respectively. The recovery was more than 99% using the standard addition method. The developed method was found to be specific, accurate, precise, and robust against changes in column temperature (±5°C) and mobile phase composition (±5% ACN); hence, it can be used for the determination of APX and CLOP in the fixed-dose combination tablets.

Deep learning-based high performance liquid chromatography for food analysis

Abstract This paper presents a study on the determination of synthetic pigments using high performance liquid chromatography (HPLC) method combined. A retention value qualitative approach, combined with an uncertainty assessment algorithm for the determination of pigment content, was used for the simultaneous determination of nine synthetic pigments, namely, lemon yellow, amaranthine red, indigo, carmine, sunset yellow, brilliant blue, seductive red, erythrosine, and seductive red, in foodstuffs by reversed-phase high-performance liquid chromatography (RP-HPLC). The sample pretreatment method was optimized, and the chromatographic conditions were set to investigate the UV determination wavelength, mobile phase, column temperature, and wavelength of synthetic pigments. Under the same mobile phase and column conditions, the results indicated that the components’ retention times did not significantly fluctuate with the change in column temperature. The results showed that the chromatographic response signals of lemon yellow, sunset yellow and seductive red were higher at the UV determination wavelength of 254 nm, so 254 nm was finally determined as the UV detection wavelength in this experiment. Mobile phase A: methanol, B: ammonium acetate (0.02mo/L) using gradient elution, the separation degree R>1.5, and the symmetry and stability of the chromatogram were better. The separation of the components was good, and the peak shape was sharp and symmetric when the column temperature was 35 ℃, so the column temperature was chosen to be 35 ℃, and the establishment of the chromatographic conditions was thus completed.

Simultaneous enantio- and diastereo-selective high-performance liquid chromatography separation of paroxetine on an immobilized amylose-based chiral stationary phase under green reversed-phase conditions

A simple and green high-performance liquid chromatography method for the separation of paroxetine from its enantiomeric and diastereomeric impurities has been developed. The simultaneous chromatographic resolution was carried out on the amylose-based Chiralpak IA-3 chiral stationary phase using the mixture ethanol-water-diethylamine 80:20:0.1 (v/v/v) as a mobile phase. The effects of substitution of ethanol with methanol or acetonitrile and changes in column temperature on selectivity have been carefully investigated. The optimized single-run HPLC protocol allows the baseline separation of the enantiomers of paroxetine without suffering from interference from five other chiral and achiral impurities reported in the monograph of the European Pharmacopoeia.

Chiral Separation and Determination of Etoxazole Enantiomers in Vegetables by Normal-Phase and Reverse-Phase High Performance Liquid Chromatography.

The chiral separation of etoxazole enantiomers on Lux Cellulose-1, Lux Cellulose-3, Chiralpak IC, and Chiralpak AD chiral columns was carefully investigated by normal-phase high performance liquid chromatography and reverse-phase high performance liquid chromatography (HPLC). Hexane/isopropanol, hexane/n-butanol, methanol/water, and acetonitrile/water were used as mobile phase at a flow rate of 0.8 mL/min. The effects of chiral stationary phase, mobile phase component, mobile phase ratio, and temperature on etoxazole separation were also studied. Etoxazole enantiomers were baseline separated on Lux Cellulose-1, Chiralpak IC, and Chiralpak AD chiral columns, and partially separated on Lux Cellulose-3 chiral column under normal-phase HPLC. However, the complete separation on Lux Cellulose-1, Chiralpak IC, and partial separation on Chiralpak AD were obtained under reverse-phase HPLC. Normal-phase HPLC presented better resolution for etoxazole enantiomers than reverse-phase HPLC. Thermodynamic parameters, including ΔH and ΔS, were also calculated based on column temperature changes from 10 °C to 40 °C, and the maximum resolutions (Rs) were not always acquired at the lowest temperature. Furthermore, the optimized method was successfully applied to determine etoxazole enantiomers in cucumber, cabbage, tomato, and soil. The results of chiral separation efficiency of etoxazole enantiomers under normal-phase and reverse-phase HPLC were compared, and contribute to the comprehensive environmental risk assessment of etoxazole at the enantiomer level.

The Semidirect Effect of Combined Dust and Sea Salt Aerosols in a Multimodel Analysis

AbstractTo date, very few studies have focused on dust and sea salt cloud interactions, particularly the semidirect effect (SDE) that results from changes in column temperature and moisture. Here, we isolate the SDE using several climate models driven by semiempirical dust and sea salt direct radiative effects. The global annual mean SDE varies from 0.01 to 0.10 W/m2, with the bulk of the signal coming from an increase in shortwave radiation. This is consistent with decreases in low cloud over ocean due to cloud burn‐off and reductions in midlevel cloud over land due to atmospheric stabilization and decreased convection. Overall, longwave effects weaken the positive SDE but with opposing effects over land and sea. High cloud is reduced over land but enhanced over sea. We conclude that dust and sea salt likely exert a global mean warming effect through cloud rapid adjustments.

Improved Reversed Phase Chromatography of Hydrophilic Peptides from Spatial and Temporal Changes in Column Temperature.

Reversed phase chromatography is an established method for peptide separation and frequently coupled to electrospray ionization-mass spectrometry for proteomic analysis. Column temperature is one parameter that influences peptide retention and elution, but it is often overlooked as its implementation requires additional equipment and method optimization. An apparatus that allows temperature manipulation in three areas of a two-column setup was evaluated for improvements in chromatography. Using commercially available standards, we demonstrate that a low column temperature (0 °C) during sample loading enhances the peak shape of several bovine serum albumin hydrophilic peptides. For digested HeLa lysates, approximately 15% more peptide identifications were obtained by increasing the precolumn temperature to 50 °C after the 500 ng sample was loaded at a low temperature. This method also identified additional early eluting peptides with grand average of hydropathicity values less than -2. We also investigated the effect of cooler column temperatures on peptides with post-translational modifications. It was possible to minimize the coelution of an isoaspartylated peptide and its unmodified version when the analytical column temperature was decreased to 5 °C. Aside from demonstrating the utility of lower temperatures for improved chromatography, its application at specific locations and time points is critical for peptide detection and separation.

Determination of Tyrian purple by high performance liquid chromatography with diode array detection

Indigotin, indirubin, 6-bromoindigotin, 6′-bromoindirubin, 6-bromoindirubin, 6,6′-dibromoindigotin and 6,6′-dibromoindirubin, the colouring components of Tyrian purple, are quantified by an efficient HPLC method coupled to a diode array detector. The compounds were separated using gradient elution, on a RP-column (Alltima C18, 250mm×3.0mm i.d., 5μm), thermostated at 35°C, with a mobile phase consisting of solvents (Α) H2O+0.1% (v/v) trifluoroacetic acid and (Β) acetonitrile+0.1% (v/v) trifluoroacetic acid, at a flow rate of 0.5mLmin−1. The method was validated in terms of linearity, detection and quantification limits, precision, accuracy, ruggedness and robustness, the latter with respect to small changes in column temperature and in flow-rate, pH- and solvent composition of the mobile phase. Under optimal conditions, the developed analytical scheme offers limits of detection in the range 0.02–0.05μgmL−1 and satisfactory linearity up to 2.5μgmL−1 for all analytes. Four samples produced from the hypobranchial glands of Hexaplex (Murex) trunculus molluscs, collected in the coastlines of Tunisia and Croatia, were treated with hot DMSO and analysed by the established HPLC method, using the standards addition approach. To evaluate the matrix effect, a comparison of the slopes of the standards in solvent regression curves with those of the standard addition method’s calibration curves, using the Student’s t-test was carried out. The accuracy was evaluated by recovery experiments. Amounts of indigotin, indirubin, and their mono- and dibrominated derivatives ranging between 0.01 to 12.2μgmg−1 were found in the DMSO extracts of the four molluscan samples.

Reverse phase high-performance liquid chromatography for quantification of hydroxymethylnitrofurazone in polymeric nanoparticles

Hydroxymethylnitrofurazone (NFOH) is a new compound with potential leishmanicidal and trypanocidal activity. Despite its effectiveness, the formulators have to overcome its poor aqueous solubility. Recently, polymeric nano-scale drug delivery systems have proposed for the treatment of neglected diseases. As several studies have confirmed the advantages of such formulations, and this approach provides new analytical challenges, including the need to detect trace amounts of the drug. A suitable method was developed and validated for NFOH determination bound to poly (n-butylcyanoacrylate) (PBCA) nanoparticles. The chromatographic separation was achieved using a C18 column maintained at 25 ºC and an isocratic mobile phase consisting of water and acetonitrile: 80:20 (v/v) at a flow rate of 1.2 mL min-1 and UV-detection at 265 nm. Investigated validation parameters included selectivity, linearity, accuracy, precision and robustness (changes in column temperature, mobile phase composition and flow). The method was specific, the peak of NFOH had no interference with any nanoparticle excipients and no co-elution with main degradation product (nitrofurazone). Linearity was over the range of 0.94 13.11 μg mL-1 (r2=0.999). The method was accurate and precise, recovery of 100.7%, RSD of 0.4%; intra-day and inter-day RSD range 9.98-9.99 μg mL-1 and 0.3% to 0.5%, respectively. Robustness confirmed that method could resist the applied changes. Application of the optimized method revealed an encapsulation efficiency of 64.4% (n=3). Therefore, the method was successfully developed and validated for the determination of the encapsulation efficiency of NFOH-PBCA nanoparticles.

Selectivity-column temperature relationship as a new strategy in predicting separation of structural analogues in HPLC by using different stationary phases

The effect of changes in column temperature on van't Hoff equation, as well as relationship of separation and column temperature in high performance liquid chromatography (HPLC) by using different stationary phases, have been discussed and compared.

Direct detection of free fatty acids in edible oils using supercritical fluid chromatography coupled with mass spectrometry

Determination of free fatty acids (FFAs) in food products is of enormous interest mainly because they are related to the quality and authenticity of the oils. In this study, supercritical fluid chromatography (SFC), followed by an electrospray ionisation triple–quadrupole mass spectrometry (ESI-MS), is shown to provide a novel method for the separation and detection of FFAs in edible oils without any pretreatment. Eight FFAs were separated on a HSS C18 SB column with gradient elution within 3min. Effects of different columns, modifiers and column temperature changes were evaluated. The results indicated the feasibility of this method for the high-throughput determination of individual FFAs with satisfactory correlation coefficients (R2>0.994) and good reproducibility of RSD<13.5% (intraday) and <15.0% (interday). By combined with principal component analysis (PCA), different types of edible oil were successfully distinguished into several categories, showing a potential application for the determination of oil quality or authenticity.

Development and Validation of a Reversed-Phase High-Performance Liquid Chromatography Method for Routine Identification and Purity Assessment of High-Purity Steviol Glycoside Sweeteners

The widespread application of stevia-based sweeteners in food products has resulted in the need for reliable analytical methods for measuring the purity and identity of high-purity steviol glycoside ingredients. The objective of this research was to develop and validate a new reversed-phase separation method capable of separating and quantifying nine steviol glycosides present in typical high-purity stevia extract ingredients. Results of the study established the linearity of the method at a correlation factor of 1.000 for the two major components and other minor components of this food ingredient. Method accuracy values were in the range of 99.1-100.9%. The percent relative standard deviation for six independent assay determinations was 1.0%. The method was determined to be robust for minor changes in column temperature, initial acetonitrile content, flow rate, and wavelength. The validated high-performance liquid chromatography method was found to be suitable to be included by USP as a Food Chemicals Codex compendial standard for steviol glycosides.

Interferon-α 2b quantification in inclusion bodies using Reversed Phase-Ultra Performance Liquid Chromatography (RP-UPLC)

Interferon-α 2b (IFN-α 2b) is a recombinant therapeutic cytokine produced as inclusion bodies using a strain of Escherichia coli as expression system. After fermentation and recovery, it is necessary to know the amount of recombinant IFN-α 2b, in order to determine the yield and the load for solubilization, and chromatographic protein purification steps. The present work details the validation of a new short run-time and fast sample-preparation method to quantify IFN-α 2b in inclusion bodies using Reversed Phase-Ultra Performance Liquid Chromatography (RP-UPLC). The developed method demonstrated an accuracy of 100.28%; the relative standard deviations for method precision, repeatability and inter-day precision tests were found to be 0.57%, 1.54% and 1.83%, respectively. Linearity of the method was assessed in the range of concentrations from 0.05 mg/mL to 0.5 mg/mL, the curve obtained had a determination coefficient ( r 2) of 0.9989. Detection and quantification limits were found to be 0.008 mg/mL and 0.025 mg/mL, respectively. The method also demonstrated robustness for changes in column temperature, and specificity against host proteins and other recombinant protein expressed in the same E. coli strain.

Low Thermal Mass Liquid Chromatography

A novel technique, low thermal mass liquid chromatography (LTMLC), is introduced in this study. The use of an LTM assembly that utilizes the principle of resistive wire heating and a temperature sensor to accurately deliver unprecedented heating (up to 1800 degrees C/min) or cooling (100 to approximately 200 degrees C/min) rates is reported. With the use of packed microcolumns (<0.5 mm i.d.), essentially instantaneous heat transfer from the assembly to the mobile phase was obtained. A systematic investigation was conducted to study the performance of the LTMLC technique. Both isocratic and gradient mobile phase conditions were used. For temperature control, isothermal, temperature-increasing, and temperature-decreasing gradients were applied. Three model mixtures, two of which containing neutral and acidic analytes and the other containing neutral, acidic, and basic analytes, were used to study the effect of temperature on elution time, resolution, column efficiency, and selectivity. It was found that the LTMLC experimental setup delivered reliable temperature control, as evidenced by linear van't Hoff plots for neutral and acidic compounds. The effect of temperature on the elution of basic analytes yielded nonlinear van't Hoff plots, explaining the dramatic selectivity changes observed for bases with changes in column temperature. Column efficiency generally increased with the increase in column temperature in the range of 25 to approximately 75 degrees C and decreased in the range of 75 to approximately 150 degrees C at a fixed column flow rate (3 microL/min), when extra column band broadening was taken into account. The increase in efficiency upon the increase in column temperature in the low temperature range was mainly due to the decreased mass transfer term resulting from increased analyte diffusivity. However, under even higher temperatures, the longitudinal diffusion dominated band broadening, explaining the decrease in column efficiency upon a further increase in column temperature. Resolution and selectivity decreased at elevated temperature for neutral and acidic compounds. For mixtures that contain bases, improved resolution was obtained by simultaneously tuning temperature and solvent programming. In addition to heating ability, LTMLC also demonstrated reliable cooling capability, allowing performance of oscillated or cycled temperature programming for fine-tuning the separation of critical band pairs for the first time. Finally, ultrafast reproducible LTMLC was also demonstrated, showing the potential of utilization of this technology for fast and ultrafast separations.

Theory and Application of the Two-Mode Gradient Elution in Liquid Chromatography Involving Simultaneous Changes in Temperature and Mobile-Phase Composition

The theory of the dual-mode gradient elution in liquid chromatography involving any type of simultaneous changes in column temperature and mobile-phase composition is developed following Drake's approach. The theory was tested in the retention prediction of six alkylbenzenes in aqueous eluting systems modified by acetonitrile. Significant delay phenomena, i.e., a lag between the programmed gradient temperature and the temperature in the oven, and a lag between the oven temperature and the effective temperature the analyte feels in the column, were detected. When these phenomena were taken into account, the retention prediction obtained for all solutes under all dual-mode gradient conditions was excellent. The average percentage error between experimental and predicted retention times is below to 2%.

Thermal stability of glucose and other sugar aldoses in normal phase high performance liquid chromatography

Analysis of glucose and other simple sugars are often performed by use of normal phase HPLC methods with acetonitrile as major eluent. The present results clearly show that column temperature plays an important role with respect to chromatographic performance and detection limits of glucose when using a specific carbohydrate column. A change in column temperature from 25 to 45 °C reduced the detection of glucose (with ELSD) by more than 41%, whereas the detection of other sugar aldoses (galactose, xylose and rhamnose) were suppressed even more. By increase of column temperature to 70 °C the detector signal of glucose was found to be less than 2% compared to that obtained at 20 °C. Neither fructose nor sucrose showed similar correlation between column temperature and detection. The rate of decreased response is not dependent on sample concentration or the ELSD settings. The results express the importance of accurate temperature control in the analysis of sugar aldoses, and also values low column temperatures for samples with low concentrations of sugar aldoses in order to improve detection.

Effect of temperature on the chromatographic retention of ionizable compounds: II. Acetonitrile–water mobile phases

The retentive behavior of weak acids and bases in reversed-phase liquid chromatography (RPLC) upon changes in column temperature has been theoretically and experimentally studied. The study focuses on examining the temperature dependence of the retention of various solutes at eluent pH close to their corresponding p K a values, and on the indirect role exerted by the buffer ionization equilibria on retention and selectivity. Retention factors of several ionizable compounds in a typical octadecylsilica column and using buffer solutions dissolved in 30% (v/v) acetonitrile as eluent at five temperatures in the range from 25 to 50 °C were carefully measured. Six buffer solutions were prepared from judiciously chosen conjugated pairs of different chemical nature. Their p K a values in this acetonitrile–water composition and within the range of 15–50 °C were determined potentiometrically. These compounds exhibit very different standard ionization enthalpies within this temperature range. Thus, whenever they are used to control mobile phase pH, the column temperature determines their final pH. Predictive equations of retention that take into account the temperature effect on both the transfer and the ionization processes are evaluated. This study demonstrates the significant role that the selected buffer would have on retention and selectivity in RPLC at temperatures higher than 25 °C, particularly for solutes that coelute.

Separation of nucleotide oligomers by unitary anion-exchange.

This paper is the first report on the retention behavior of synthetic oligonucleotides and nucleotide oligomers on a continuous-bedmatrix, strong-anion-exchange column. The separation mechanism is predominantly an anion-exchange process, but hydrophobic interaction plays a role as well. The separation is based on the chain length of the oligonucleotide. Both the addition of organic mobile phase modifiers and changes in column temperature affect the retention of oligomers significantly. A volatile buffer system (e.g., triethylamine acetate) could be employed to purify oligonucleotides, and no desalting procedure would be required after the column separation step. The recoveries from the separation are 70% or higher. The maximum loading capacity of an analytical column (35 x 7-mm i.d.) was found to be more than 366 micrograms.

Temperature programming and gradient elution in reversed-phase chromatography with packed capillary columns

The two major anisocratic elution modes were compared in reversed-phase chromagraphy with 180 μm I.D. fused-silica capillary columns acked with 6 μm Zorbax SB ODS-silica. By evaluating the retention factors of alkylbenzenes at acetonitrile concentrations varying from 60 to 80% (v/v) in the aqueous eluent and in the temperature range of 30–80°C, it was found that a 5°C change in column temperature and a 1% change in acetonitrile concentration have almost the same effect on retention. This is illustrated by the almost identical chromatograms of an alkylbenzene sample obtained by temperature programming and by gradient elution under the same conditions otherwise and by simulation of the trajectories of the eluent peaks moving down the column. The results suggest that in reversed-phase HPLC with packed capillary columns temperature programming offers an alternative to gradient elution in a relatively narrow range of the required elution strength. Thermodynamic data from isocratic chromatographic measurements were used to predict the retention times of alkylbenzenes in reversed-phase chromatography with temperature programming at different heating rates and column inlet pressures. Temperature programming was used to separate β-lactoglobulins A and B by reversed-phase chromatography. It was also employed concomitantly with gradient elution to enhance the separation of a mixture of four standard proteins. The results indicate that temperature programming could serve as an adjunct to gradient elution by means of fine retention tuning to bring about or increase the resolution of closely related macromolecules.

Temperature-responsive liquid chromatography. 2. Effects of hydrophobic groups in N-isopropylacrylamide copolymer-modified silica.

We recently reported the new concept of temperature-responsive liquid chromatography using temperature-responsive poly(N-isopropylacrylamide)-modified surfaces as high-performance liquid chromatography media with aqueous mobile phases. Incorporation of hydrophobic sites is an important factor to improve the efficacy (selectivity and retention) of temperature-responsive chromatography. Toward this goal, we have synthesized semitelechelic copolymers of N-isopropylacrylamide (IPAAm) and butyl methacrylate (BMA) having reactive terminal functional groups using telomerization. The lower critical solution temperatures of the copolymers shift to lower temperatures with increasing hydrophobic BMA content in the poly(IPAAm-co-BMA) relative to that of the IPAAm homopolymer. This temperature-responsive semitelechelic copolymer was grafted to the surface of (aminopropyl)silica through the reaction of activated ester-amine coupling. The polymer-modified silica was used as a column packing material. Separation of a mixture of five steroids having various hydrophobicities was investigated. Retention of steroids on poly(IPAAm-co-BMA)-modified columns is increased with an increase in column temperature. The capacity factors for steroids on the copolymer-modified silica beads was much larger than that on homopolymer PIPAAm-modified columns. The capacity factor for testosterone at 50 degrees C was 33.8 for poly(IPAAm-co-BMA) containing 5 mol% BMA, while that for the PIPAAm homopolymer was 15.0 at the same temperature. The influence of column temperature on steroid retention behavior on copolymer-modified stationary phases was significant compared with the case of homopolymer-modified columns. Furthermore, retention times for steroids increased remarkably with increasing BMA composition. The temperature-responsive elution behavior for the steroids was strongly affected by the hydrophobicity of the grafted polymer chains on silica surfaces. Possible protein separation in temperature-responsive liquid chromatography was explored using insulin chains A and B, and beta-endorphin fragment 1-27. On IBc-3.2-modified silica column, these three peptides were successfully separated at 30 degrees C with 0.5 M NaCl aqueous solution (pH 2.1) as mobile phase. The retention times of these peptides were related to the number of hydrophobic amino acid residues in the peptides. In the proposed chromatography system, elution of target substances is controlled only by a small change in column temperature without any further modification of the aqueous mobile phase.

Determination of spectinomycin using cation-exchange chromatography with pulsed amperometric detection

An isocratic HPLC method was developed for the determination of spectinomycin dihydrochloride pentahydrate. The method is based on cation-exchange chromatography with pulsed-amperometric detection. The method was optimised for the separation of spectinomycin, actinamine and actinospectinoic acid on a Dionex IonPac CS3 column at ambient temperature with 150 m M sodium acetate (pH 6) mobile phase. Detector response with respect to sodium hydroxide concentration was investigated using cyclic voltammetry. A three-step pulse sequence with a sampling potential of + 0.05 V was used for detection. The k′ values for spectinomycin and related impurities were insensitive to column temperature changes in the range 21–50°C and show only minor variations to pH changes in the range 5.0–6.0. The method is linear and unbiased for the determination of spectinomycin over the concentration range 25–200 μg/ml for 50-μl injections. Two-day precision data for the method show within-sample R.S.D.s in the range 0.3–1.0% and between-day R.S.D.s in the range 0.3–0.9%. The limits of detection and quantitation determined for spectinomycin are 0.02 μg and 0.06 μg on-column, respectively. The method is suitable for the analysis of drug-substance.