Centre National d'Etudes Spatiales Research Articles

Development of Innovative Mechanical Flexible Solar Array Architecture

Flexible solar array architecture is proposed instead of rigid one, for high power solar array used from space tug mission to GEO satellite one, but also for specific scientific mission. THALES ALENIA SPACE has developed with Centre National d’Etudes Spatiales (CNES) support, innovative mechanical flexible solar array architecture, using 22 m long carbon tape-springs.The first part of the study was to design, predict, verify carbon tape-springs mechanical behaviour during deployment and coiling phases at room temperature. THALES ALENIA SPACE built mechanical flexible solar array mock-up full scale width / half scale length and performed deployment and rolling-up tests.The second part was to design, predict carbon tape-springs mechanical behaviour with large temperature range due to solar array missions. THALES ALENIA SPACE used again flexible solar array mock-up, performed deployment/coiling tests with innovative tape springs.This 11th ESPC paper describes results of these development activities and the THALES ALENIA SPACE forecast on this flexible solar array market.

An Inquiry on Contrast Enhancement Methods for Satellite Images

Enhancement algorithms are absolutely necessary for the visualization of both shadowed and bright image regions. Defining algorithms that permit to visualize them simultaneously without altering the image content is therefore extremely relevant for remote sensing applications. In this paper, we present the results of two successive benchmarks which tested the performance of the state-of-the-art contrast enhancement and tone-mapping algorithms applied to satellite images. Experts from the French Space Agency Centre National d'Etudes Spatiales (CNES), Service Regional de Traitement d'Image et de Teledetection (SERTIT), and two European universities assessed the quality and fidelity of the results of several state-of-the-art enhancement algorithms on the excerpts from seven images (five Pleiades and two simulated 30-cm images). The first benchmark permitted to tighten the procedure and the selection of the test images for the second one, and to make a first selection of concurrent algorithms. The second benchmark not only included the best algorithms selected by the first benchmark but also added even more competitors in the tone-mapping class. The results of both benchmarks were coherent. They point a particular retinex-based algorithm as the best compromise between the competitive requirements of a contrast enhancement in dark regions and a preservation of detail in bright parts.

Satellite radar altimetry water elevations performance over a 200 m wide river: Evaluation over the Garonne River

For at least 20 years, nadir altimetry satellite missions have been successfully used to first monitor the surface elevation of oceans and, shortly after, of large rivers and lakes. For the last 5–10 years, few studies have demonstrated the possibility to also observe smaller water bodies than previously thought feasible (river smaller than 500m wide and lake below 10km2). The present study aims at quantifying the nadir altimetry performance over a medium river (200m or lower wide) with a pluvio-nival regime in a temperate climate (the Garonne River, France). Three altimetry missions have been considered: ENVISAT (from 2002 to 2010), Jason-2 (from 2008 to 2014) and SARAL (from 2013 to 2014).Compared to nearby in situ gages, ENVISAT and Jason-2 observations over the lower Garonne River mainstream (110 km upstream of the estuary) have the smallest errors, with water elevation anomalies root mean square errors (RMSE) around 50cm and 20cm, respectively. The few ENVISAT upstream measurements have RMSE ranging from 80cm to 160cm. Over the estuary, ENVISAT and SARAL water elevation anomalies RMSE are around 30cm and 10cm, respectively.The most recent altimetry mission, SARAL, does not provide river elevation measurements for most satellite overflights of the river mainstream. The altimeter remains “locked” on the top of surrounding hilly areas and does not observe the steep-sided river valley, which could be 50–100m lower. This phenomenon is also observed, for fewer dates, on Jason-2 and ENVISAT measurements. In these cases, the measurement is not “erroneous”, it just does not correspond to water elevation of the river that is covered by the satellite. ENVISAT is less prone to get ‘locked’ on the top of the topography due to some differences in the instrument measurement parameters, trading lower accuracy for more useful measurements. Such problems are specific to continental surfaces (or near the coasts), but are not observed over the open oceans, which are flatter.To overcome this issue, an experimental instrument operating mode, called the DIODE/DEM tracking mode, has been developed by CNES (Centre National d’Etudes Spatiales) and has been tested during few Jason-2 cycles and during the first SARAL/AltiKA cycle. This tracking mode “forces” the instrument to observe a target of interest, i.e. water bodies. The example of the Garonne River shows, for one SARAL ground track, the benefit of the DIODE/DEM tracking mode for a steep-sided river reach, which is not detected using the nominal instrument operating mode. Yet, this mode relies on ancillary datasets (a priori global DEM and global land/water mask), which are critical to obtain river valley observation. The ultimately computed elevations along the satellite tracks, loaded on board, should have an absolute vertical accuracy around 10m (or better). This case also shows, when the instrument is correctly observing the river valley, that the altimeter can detect water bodies narrower than 100m (like an artificial canal).In agreement with recent studies, this work shows that altimeter missions can provide useful water elevation measurements over a 200m wide river with RMSE as low as 50cm and 20cm, for ENVISAT and Jason-2 respectively. The seasonal cycle can be observed with the temporal sampling of these missions (35 days and 10 days, respectively), but short term events, like flood events, are most of the time not observed. It also illustrates that altimeter capability to observe a river is highly dependent of the surrounding topography, the observation configuration, previous measurements and the instrument design. Therefore, it is not possible to generalize at global scale the minimum river width that could be seen by altimeters.This study analyzes, for the first time, the potential of the experimental DIODE/DEM tracking mode to observe steep-sided narrow river valleys, which are frequently missed with nominal tracking mode. For such case, using the DIODE/DEM mode could provide water elevation measurements, as long as the on board DEM is accurate enough. This mode should provide many more valid measurements over steep-sided rivers than currently observed.

Low-Atmosphere Drifting Balloons: Platforms for Environment Monitoring and Forecast Improvement

Abstract Balloons are one of the key observing platforms for the atmosphere. Radiosounding is the most commonly used technique and provides over a thousand vertical profiles worldwide every day. These data represent an essential cornerstone of data assimilation for numerical weather prediction systems. Although less common (but equally interesting for the in situ investigation of the atmosphere), drifting boundary layer pressurized balloons (BLPBs) offer rare observational skills. These balloons collect meteorological and/or chemical measurements at isopycnal height as they drift in a quasi-Lagrangian way. The BLPB system presented in this paper was developed by the French Space Agency [Centre National d’Études Spatiales (CNES)] and has been used in field experiments focusing on precipitation in Africa [African Monsoon Multiscale Analysis (AMMA)] and the Mediterranean [Hydrological Cycle in the Mediterranean Experiment (HyMeX)] as well as on air pollution in India [Indian Ocean Experiment (INDOEX)] and the Mediterranean [Transport a Longue Distance et Qualite de l’Air dans le bassin Méditerraneen (TRAQA) and Chemistry–Aerosol Mediterranean Experiment (ChArMeX)]. One important advantage of BLPBs is their capability to explore the lowest layers of the atmosphere above the oceans, areas that remain difficult to access. BLPB had a leading role in a complex adaptive observation system for the forecast of severe precipitation events. These balloons collected data in the marine environment of convective systems, which were assimilated in real time to improve the knowledge of the state of the atmosphere in the numerical prediction models of Météo-France.

On the Importance of High-Resolution Time Series of Optical Imagery for Quantifying the Effects of Snow Cover Duration on Alpine Plant Habitat

We investigated snow cover dynamics using time series of moderate (MODIS) to high (SPOT-4/5, Landsat-8) spatial resolution satellite imagery in a 3700 km2 region of the southwestern French Alps. Our study was carried out in the context of the SPOT (Take 5) Experiment initiated by the Centre National d’Etudes Spatiales (CNES), with the aim of exploring the utility of high spatial and temporal resolution multispectral satellite imagery for snow cover mapping and applications in alpine ecology. Our three objectives were: (i) to validate remote sensing observations of first snow free day derived from the Normalized Difference Snow Index (NDSI) relative to ground-based measurements; (ii) to generate regional-scale maps of first snow free day and peak standing biomass derived from the Normalized Difference Vegetation Index (NDVI); and (iii) to examine the usefulness of these maps for habitat mapping of herbaceous vegetation communities above the tree line. Imagery showed strong agreement with ground-based measurements of snow melt-out date, although R2 was higher for SPOT and Landsat time series (0.92) than for MODIS (0.79). Uncertainty surrounding estimates of first snow free day was lower in the case of MODIS, however (±3 days as compared to ±9 days for SPOT and Landsat), emphasizing the importance of high temporal as well as high spatial resolution for capturing local differences in snow cover duration. The main floristic differences between plant communities were clearly visible in a two-dimensional habitat template defined by the first snow free day and NDVI at peak standing biomass, and these differences were accentuated when axes were derived from high spatial resolution imagery. Our work demonstrates the enhanced potential of high spatial and temporal resolution multispectral imagery for quantifying snow cover duration and plant phenology in temperate mountain regions, and opens new avenues to examine to what extent plant community diversity and functioning are controlled by snow cover duration.

MASCOT—The Mobile Asteroid Surface Scout Onboard the Hayabusa2 Mission

On December 3rd, 2014, the Japanese Space Agency (JAXA) launched successfully the Hayabusa2 (HY2) spacecraft to its journey to Near Earth asteroid (162173) Ryugu. Aboard this spacecraft is a compact landing package, MASCOT (Mobile Asteroid surface SCOuT), which was developed by the German Aerospace Centre (DLR) in collaboration with the Centre National d’Etudes Spatiales (CNES). Similar to the famous predecessor mission Hayabusa, Hayabusa2, will also study an asteroid and return samples to Earth. This time, however, the target is a C-type asteroid which is considered to be more primitive than (25143) Itokawa and provide insight into an even earlier stage of our Solar System. Upon arrival at asteroid Ryugu in 2018, MASCOT will be released from the HY2 spacecraft and gently descend by free fall from an altitude of about 100 m to the surface of the asteroid. After a few bounces, the lander will come to rest at the surface and perform its scientific investigations of the surface structure and mineralogical composition, the thermal behaviour and the magnetic properties by operating its four scientific instruments. Those include an IR imaging spectrometer (MicrOmega, IAS Paris), a camera (MASCAM, DLR Berlin), a radiometer (MARA, DLR Berlin) and a magnetometer (MASMAG, TU Braunschweig). In order to allow optimized payload operations the thermal design of MASCOT is required to cope with the contrasting requirements of the 4-year cruise in cold environment versus the hot conditions on the surface of the asteroid. Operations up to 2 asteroid days (∼16 hours) based on a primary battery are currently envisaged. A mobility mechanism allows locomotion on the surface. The mechanism is supported by an attitude and motion sensing system and an intelligent autonomy manager, which is implemented in the onboard software that enables MASCOT to operate fully independently when ground intervention is not available.

Research on a method of real-time combination of precise GPS clock corrections

The acquisition of real-time satellite orbit and clock corrections is necessary for real-time PPP. There are nine International GNSS Service (IGS) analysis centers (ACs) that provide real-time satellite orbit and clock products. Given the influence of network transmission, observation data and solution methods, a single AC product suffers from outages and outliers. A combination of real-time data streams is an effective method of improving these problems. We focus on a combination method with regard to anomalous data in a single AC solution. Processing techniques such as parameter separation, weight estimation and exception handling are proposed. Experimental results indicate that, after the process, the frequency of unavailability and anomaly in the combined (simply COMB later) clock correction obtained using the above-mentioned method decreases relative to that of a single AC and IGS01 and IGS02 products. IGS01 is a single-epoch combined product provided by European Space Agency (ESA). IGS02 is a Kalman filter combined product provided by the Federal Agency for Cartography and Geodesy (BKG). In a 7-day experimental period, the performance of real-time products is also examined regarding availability and accuracy. The availability of COMB is as high as 99.9 %, which is superior to that of single AC and IGS01 and IGS02 products. The accuracy of COMB is 0.15 ns in standard deviation, which is at the same level as the Centre National d'Etudes Spatiales (CNES) product, but higher by 40, 17, 29, 42 and 32 % than that of the German Aerospace Center (DLR), ESA, GeoForschungsZentrum (GFZ), IGS01 and IGS02 products. The 3D positioning accuracy applying COMB product is 9.1 cm in root mean square (RMS), which is higher by 41, 44, 5, 43, 43 and 42 % than applying CNES, DLR, ESA, GFZ, IGS01 and IGS02 products, respectively. The results demonstrate that the real-time COMB clock correction obtained by the method proposed is more stable and reliable than single AC and IGS01 and IGS02 products.

Validation of SARAL/AltiKa significant wave height and wind speed observations over the North Indian Ocean

SARAL/AltiKa, a joint Ka-band altimetry mission of the Centre National d’Etudes Spatiales (CNES) and Indian Space Research Organisation (ISRO) was successfully launched on February 25, 2013. The main purpose of this mission is to explore the ocean surface topography. As it is a Ka-band altimeter mission unlike other altimeters which were primarily in Ku-band, it is essential to calibrate and validate AltiKa data products before using the data for oceanographic applications. With this objective, two important geophysical parameters, Significant Wave Height (SWH) and Wind Speed (WS) from SARAL/AltiKa are inter-compared with those from 18 moored buoy stations in the North Indian Ocean (NIO) for a two year period from March 2013 to March 2015. SARAL/AltiKa GDR-T patch-2 version products are collocated with moored buoy observations with a collocation criteria of spatio-temporal window of 50km radius about the buoy location and 30min time for all the altimeter measurements. Following this, linear regression relations are developed and statistical analyses carried out to assess the performance of SARAL/AltiKa. The correlation between SARAL/AltiKa derived SWHs and those from moored buoys is 0.98m with a bias of −0.02m and Root Mean Square Error (RMSE) of 0.15m at 95% confidence level. The WSs derived from SARAL/AltiKa Ka-band correlates reasonably well with buoy observations with a correlation coefficient of 0.91, bias of −0.28m/s and RMSE of 1.13m/s. The inter-comparison results are found to be interesting with a good agreement between SARAL/AltiKa and moored buoys observations of SWH and WS in the NIO where SWHs are less than ∼4m and WS are less than ∼13m/s during the entire analysis period.

SPOT-4 (Take 5): Simulation of Sentinel-2 Time Series on 45 Large Sites

This paper presents the SPOT-4 (Take 5) experiment, aimed at providing time series of optical images simulating the repetitivity, the resolution and the large swath of Sentinel-2 images. The aim was to help users set up and test their applications and methods, before Sentinel-2 mission data become available. In 2016, when both Sentinel-2 satellites are operational, and for at least fifteen years, users will have access to high resolution time series of images systematically acquired every five days, over the whole Earth land surfaces. Thanks to Sentinel-2’s high revisit frequency, a given surface should be observed without clouds at least once a month, except in the most cloudy periods and regions. In 2013, the Centre National d’Etudes Spatiales (CNES) lowered the orbit altitude of SPOT-4, to place it on a five-day repeat cycle orbit for a duration of five months. This experiment started on 31 January 2013 and lasted until 19 June 2013. SPOT-4 images were acquired every fifth day, over 45 sites scattered in nearly all continents and covering very diverse biomes for various applications. Two ortho-rectified products were delivered for each acquired image that was not fully cloudy, expressed either as top of atmosphere reflectance (Level 1C) or as surface reflectance (Level 2A). An extensive validation campaign was held to check the performances of these products with regard to the multi-temporal registration, the quality of cloud masks, the accuracy of aerosol optical thickness estimates and the quality of surface reflectances. Despite high a priori geo-location errors, it was possible to register the images with an accuracy better than 0.5 pixels in the large majority of cases. Despite the lack of a blue band on the SPOT-4 satellite, the cloud and shadow detection yielded good results, while the aerosol optical thickness was measured with a root mean square error better than 0.06. The surface reflectances after atmospheric correction were compared with in situ data and other satellite data showing little bias and the standard deviation of surface reflectance errors in the range (0.01–0.02). The Take 5 experiment is being repeated in 2015 with the SPOT-5 satellite with an enhanced resolution.

Analysis of SARAL/AltiKa Wind and Wave over Indian Ocean and its Real-time Application in Wave Forecasting System at ISRO

The current study aims to analyze the wind and wave parameters over Indian Ocean region obtained from first Ka –band altimeter AltiKa onboard SARAL, a collaborative mission of Indian Space Research Organization (ISRO) and Centre National d'Etudes Spatiales (CNES), France. It also demonstrates a real time application of SARAL data by assimilating the wave height in a wave model operational at the Space Applications Centre, ISRO. State-of–the art coastal wave model Simulating Wave Near shore (SWAN) is used for this purpose. The well-tested optimal interpolation technique is adopted for assimilation. Before proceeding to the assimilation per se, SARAL/AltiKa Wind and Significant Wave Height (SWH) have been validated using in- situ observations and WAVEWATCH III model. Apart from assessment of wind and wave data quality, this also served the purpose of providing error covariance to be used in assimilation. Supremacy of the assimilation run over parallel control run without assimilation has been judged by comparing the results with buoy observations at Indian National Centre for Ocean Information System (INCOIS). The statistics of validation of the assimilation run has been found to be extremely encouraging and interesting.

Validation of SWH and SSHA from SARAL/AltiKa Using Jason-2 and In-Situ Observations

The focus of this study is the validation of significant wave height (SWH) and sea surface height anomaly (SSHA) obtained from the first Ka-band altimeter AltiKa onboard SARAL (Satellite for ARGOS and Altimeters). It is a collaborative mission of the Indian Space Research Organization and Centre National d'Etudes Spatiales (CNES). This is done using in-situ observations from buoy and Jason-2 measurements. Validation using buoy observations are at particular locations while that using Jason-2 altimeter is an attempt towards global validation of Altika products. The results clearly indicate that the SARAL/AltiKa provide high-quality data and the errors are within a predefined range of accuracy. A parallel validation of SWH from other altimeters, which monitored ocean since last decade, like EnviSAT and Jason-2 was also performed with buoy observations. The results clearly show that the accuracy of AltiKa SWH is much better than EnviSAT and comparable to reference mission Jason-2. The accuracy is quite good for the calm sea while in the rough seas the accuracy degrades some. The inter-comparison of SARAL/AltiKa SSHA with Jason-2 indicates a fair match between them. These validation exercises demonstrate the high quality of AltiKa products, usable for practical applications.

Autonomous star sensor ASTRO APS: flight experience on Alphasat

Jena-Optronik GmbH, located in Jena/Germany, has profound experience in designing and manufacturing star trackers since the early 80s. Today the company has a worldwide leading position in supplying geo-stationary and Earth observation satellites with robust and reliable star tracker systems. In the first decade of the new century Jena-Optronik received a development contract (17317/2003/F/WE) from the European Space Agency to establish the technologically challenging elements for which advanced star tracker technologies as CMOS Active Pixel Sensors were being introduced or were considered strategic. This activity was performed in the frame of the Alphabus large platform pre-development lead by ESA and the industrial Joint Project Team consisting of Astrium (now Airbus Defence and Space), Thales Alenia Space and CNES (Centre national d’etudes spatiales). The new autonomous star tracker, ASTRO APS (Active Pixel Sensor), extends the Jena-Optronik Astro-series CCD-based star tracker products taken the full benefit of the CMOS APS technology. ASTRO APS is a fully autonomous compact star tracker carrying either the space-qualified radiation hard STAR1000 or the HAS2 APS detectors. The star tracker is one of four Technology Demonstration Payloads (TDP6) carried by Alphasat as hosted payload in the frame of a successful Private Public Partnership between ESA and Inmarsat who owns and operates the satellite as part of its geo-stationary communication satellites fleet. TDP6 supports also directly TDP1, a Laser Communication Terminal, for fine pointing tasks. Alphasat was flawlessly brought in orbit at the end of July 2013 by a European Ariane 5 launcher. Only a few hours after launch the star tracker received its switch ON command and acquired nominally within 6 s the inertial 3-axes attitude. In the following days of the early in-orbit operations of Alphasat the TDP6 unit tracked reliably all the spacecraft maneuvers including the 0.1 and 0.2°/s spin stabilization for Sun pointing, all of the apogee engine thrusts, Moon field of view transits and recovered to stable tracking after several Earth and Sun blindings before the spacecraft entered a preliminary Earth pointing in a nominal geo-stationary attitude. The Jena-Optronik TDP6 operation center received daily the star tracker status and attitude data. The huge amount of acquired raw data has been evaluated to characterize the ASTRO APS (STAR1000) star tracker in-orbit performance. The paper will present in detail these data processing activities and will show the extraordinary good results. Due to the diverse transfer orbit satellite operations the key performance star tracker data like attitude random noise, single star noise, star brightness measurement, baffle Sun exclusion angle, temperature control, etc., could be derived and have been compared to the ground based laboratory and field measurements. The ultimate performance parameters achieved and verified as well as the lessons learned from the comparison to the ground test data are summarized in the conclusion of the paper.

Applying OntoREM to a Space Mission: Developing Requirements for the MASCOT Lander

AbstractOntoREM is an Ontology‐driven Requirements Engineering Methodology supported by software tooling, developed jointly by UWE and Airbus. OntoREM has been tested using a number of pilot cases in various domains at Airbus. In this research, OntoREM is applied to a space mission called MASCOT (Mobile Space Asteroid Scout) developed by DLR (Deutsches Zentrum für Luft‐ und Raumfahrt), Germany, together with CNES (Centre National d'Etudes Spatiales), France, and the Japanese Space Agency (JAXA). The research provided the opportunity to carry out a comparative critical evaluation of the outcomes of the application of OntoREM to MASCOT versus the outcomes of a more traditional Systems Engineering approach as applied by DLR‐Bremen. The key objective was to generate an alternative set of MASCOT requirements using OntoREM based on the existing set of MASCOT system requirements, and to compare the quality of the resulting requirements with the quality of the existing requirements in terms of correctness, completeness and consistency. The application of OntoREM to MASCOT has been successful, it appears that OntoREM is suitable for the development of requirements for space mission programmes and creates quality improvements when generating requirement specifications. About 100% additional project and system requirements were identified, while a re‐usable MASCOT project domain ontology was built during the process that may be generalised for future lander missions.

Quality assessment of onboard GPS receiver and its combination with DORIS and SLR for Haiyang 2A precise orbit determination

The GPS, DORIS, and SLR instruments are installed on Haiyang 2A (HY2A) altimetry satellite for Precise Orbit Determination (POD). Among these instruments, the codeless GPS receiver is the state-of-art Chinese indigenous onboard receiver, and it is the first one successfully used for Low Earth Orbit (LEO) satellite. Firstly, the contribution assesses the performance of the receiver through an analysis of data integrity, numbers of all tracked and valid measurements as well as multipath errors. The receiver generally shows good performance and quality despite a few flaws. For example, L2 observations are often missing in low elevations, particularly during the ascent of GPS satellites, and the multipath errors of P1 show a slightly abnormal pattern. Secondly, the PCO (Phase Center Offset) and PCV (Phase Center Variation) of the antenna of the GPS receiver are determined in this contribution. A significant leap for Z-component of PCO up to −1.2 cm has been found on 10 October 2011. Thirdly, the obtained PCO and PCV maps are used for GPS only POD solutions. The post-fit residuals of ionosphere-free phase combinations reduce almost 50%, and the radial orbit differences with respect to CNES (Centre National d’Etudes Spatiales) Precise Orbit Ephemeris (POEs) improve about 13.9%. The orbits are validated using the SLR data, and the RMS of SLR Observed minus Computed (O-C) residuals reduces from 17.5 to 15.9 mm. These improvements are with respect to the orbits determined without PCO and PCV. Fourthly, six types of solutions are determined for HY2A satellite using different combinations of GPS, DORIS, and SLR data. Statistics of SLR O-C residuals and cross-comparison of orbits obtained in the contribution and the CNES POEs indicate that the radial accuracy of these orbits is at the 1.0 cm level for HY2A orbit solutions, which is much better than the scientific requirements of this mission. It is noticed that the GPS observations dominate the achievable accuracy of POD, and the combination of multiple types of observations can reduce orbit errors caused by data gaps and maintain more stable and continuous orbits.

Layer average relative humidity from SAPHIR on board Megha-Tropiques: validation with numerical model analyses

Subsequent to the launch of the Sondeur Atmosphérique du Profil d’Humidité Intertropicale par Radiométrie (SAPHIR) sensor on board the Megha-Tropiques satellite on 12 October 2011 from Satish Dhawan Space Centre, Indian Space Research Organization (ISRO), Shriharikota, India, the validation of layer averaged relative humidity (LARH) retrieved from SAPHIR has been initiated in different phases along with other retrieved parameters. The Megha-Tropiques is a joint satellite mission executed by the Indian Space Research Organization (ISRO) and the Centre National d’Etudes Spatiales (CNES), and is primarily devoted to study the tropical atmospheric processes influencing both weather and climate. The present study focuses on a validation campaign, where the validation of LARH derived from SAPHIR is carried out with three different numerical model analyses: the European Centre for Medium Range Weather Forecasts (ECMWF) model, the National Centers for Environmental Prediction (NCEP) model, and the National Centre for Medium Range Weather Forecasting (NCMRWF) model, over a period of six months from January 2013 to June 2013. It is observed that the root mean square difference (RMSD) of LARH has improved considerably for layers 1, 2, 3, and 6, and some marginal changes for layers 4 and 5, when a bias correction is applied to the data. The RMSD of SAPHIR LARH after correcting for bias is well within the range of the mission goal of 20% accuracy.

Microwave interferometric radiometry in remote sensing: An invited historical review

AbstractThe launch of the Soil Moisture and Ocean Salinity (SMOS) mission on 2 November 2009 marked a milestone in remote sensing for it was the first time a radiometer capable of acquiring wide field of view images at every single snapshot, a unique feature of the synthetic aperture technique, made it to space. The technology behind such an achievement was developed, thanks to the effort of a community of researchers and engineers in different groups around the world. It was only because of their joint work that SMOS finally became a reality. The fact that the European Space Agency, together with CNES (Centre National d'Etudes Spatiales) and CDTI (Centro para el Desarrollo Tecnológico e Industrial), managed to get the project through should be considered a merit and a reward for that entire community. This paper is an invited historical review that, within a very limited number of pages, tries to provide insight into some of the developments which, one way or another, are imprinted in the name of SMOS.

Using Images of Continental Water Surface Elevations From Upcoming Satellite Mission

The proposed Surface Water and Ocean Topography (SWOT) satellite mission, which is under development at NASA, the Centre National d'Études Spatiales (CNES), and the Canadian Space Agency, is currently planned for launch in 2020. SWOT would provide maps of water surface elevation globally, observing rivers wider than about 50–100 meters and other water bodies with dimensions (widths and lengths) greater than 250 meters.

Improvement of the Representativity of the Morris Method for Air-Launch-to-Orbit Separation

This work is part of a technical study of the French space agency CNES (Centre National d'Etudes Spatiales) and the French aerospace laboratory Onera for the development of an air-launch-to-orbit system. The separation between the space launcher and the aircraft must be studied with a sensitivity analysis to estimate the role of the different uncertainties in the risk of collision and improve the robustness of the controller. As the number of factors is too large to apply a quantitative method, the qualitative Morris method is first used for factors fixing. The Morris method is generally used with limited calculations to roughly estimate the factors' impact, but the quality of its results is rarely discussed. The Morris method is based on the random sampling of so-called trajectories or, less frequently, radial points. The representativity of the trajectories and radial points is analyzed and improved with a new solution based on a discrete Latin hypercube. Extensive tests are used to compare the quality of the results of various procedures with five common test functions. A new quality indicator, more sensitive, is developed. It shows that the new solution greatly improves, at no additional cost, the estimation of the factors' impact by the Morris method. The classic radial points appear to be more efficient than the commonly used classic trajectories. From a more global perspective, this study raises the question of the convergence in the Morris method. The application of the new solution to the air-launch-to-orbit separation provides results with a much better quality indicator than in the previous campaign of sensitivity analysis.

Analysis of the potential of one possible instrumental configuration of the next generation of IASI instruments to monitor lower tropospheric ozone

Abstract. To evaluate the added value brought by the next generation of IASI (Infrared Atmospheric Sounder Interferometer) instruments to monitor lower tropospheric (LT) ozone, we developed a pseudo-observation simulator, including a direct simulator of thermal infrared spectra and a full inversion scheme to retrieve ozone concentration profiles. We based our simulations on the instrumental configuration of IASI and of an IASI-like instrument, with a factor 2 improvement in terms of spectral resolution and radiometric noise. This scenario, that will be referred to as IASI/2, is one possible configuration of the IASI-NG (New Generation) instrument (the configuration called IASI-NG/IRS2) currently designed by CNES (Centre National d'Études Spatiales). IASI-NG is expected to be launched in the 2020 timeframe as part of the EPS-SG (EUMETSAT Polar System-Second Generation, formerly post-EPS) mission. We produced one month (August 2009) of tropospheric ozone pseudo-observations based on these two instrumental configurations. We compared the pseudo-observations and we found a clear improvement of LT ozone (up to 6 km altitude) pseudo-observations quality for IASI/2. The estimated total error is expected to be more than 35% smaller at 5 km, and 20% smaller for the LT ozone column. The total error on the LT ozone column is, on average, lower than 10% for IASI/2. IASI/2 is expected to have a significantly better vertical sensitivity (monthly average degrees of freedom surface–6 km of 0.70) and to be sensitive at lower altitudes (more than 0.5 km lower than IASI, reaching nearly 3 km). Vertical ozone layers of 4 to 5 km thickness are expected to be resolved by IASI/2, while IASI has a vertical resolution of 6–8 km. According to our analyses, IASI/2 is expected to have the possibility of effectively separate lower from upper tropospheric ozone information even for low sensitivity scenarios. In addition, IASI/2 is expected to be able to better monitor LT ozone patterns at local spatial scale and to monitor abrupt temporal evolutions occurring at timescales of a few days, thus bringing an expected added value with respect to IASI for the monitoring of air quality.

Cross Calibration of Formosat-2 Remote Sensing Instrument (RSI) Using Terra Advanced Spaceborne Thermal Emission and Reflection Radiometer (ASTER)

The present paper describes the cross calibration of the Remote Sensing Instrument (RSI) onboard Formosat-2 using the Advanced Spaceborne Thermal Emission and Reflection Radiometer (ASTER) onboard Terra as a reference, which has been continuously calibrated by means of the onboard and vicarious calibration methods. The data integration system for multi-satellite sensor databases on the Global Earth Observation Grid (GEO Grid) is used in order to find pairs of images acquired by both satellite optical sensors over the radiometric calibration sites on the same days. Radiative transfer simulations that consider different imaging conditions using the Second Simulation of a Satellite Signal in the Solar Spectrum (6S) code are performed based on the Moderate-resolution Imaging Spectroradiometer (MODIS) atmosphere and land products, and the optimum methodology for this cross calibration is discussed under the assumption of no ground-based measurements. The derived calibration coefficients are normalized by the values of preflight calibration and are compared with the results of in-flight cross calibration by the Centre National d'Etudes Spatiales (CNES) and vicarious calibration described in our previous paper. The average degradations of sensor sensitivity since preflight calibration until 2009 are estimated to be 10% (Band2), 11% (Band3), and 8% (Band4). The derived long-term degradation trends are almost consistent with the results of our vicarious calibration within the precision. The cross-calibration methodology used in the present paper facilitates the in-flight radiometric calibration of satellite optical sensors.