Cathode Electrolyte Research Articles

Stabilized Nickel‐Rich‐Layered Oxide Electrodes for High‐Performance Lithium‐Ion Batteries

Next‐generation Li‐ion batteries are expected to exhibit superior energy and power density, along with extended cycle life. Ni‐rich high‐capacity layered nickel manganese cobalt oxide electrode materials (NMC) hold promise in achieving these objectives, despite facing challenges such as capacity fade due to various degradation modes. Crack formation within NMC‐based cathode secondary particles, leading to parasitic reactions and the formation of inactive crystal structures, is a critical degradation mechanism. Mechanical and chemical degradation further deteriorate capacity and lifetime. To mitigate these issues, an artificial cathode electrolyte interphase can be applied to the active material before battery cycling. While atomic layer deposition (ALD) has been extensively explored for active material coatings, molecular layer deposition (MLD) offers a complementary approach. When combined with ALD, MLD enables the deposition of flexible hybrid coatings that can accommodate electrode material volume changes during battery operation. This study focuses on depositing ‐titanium terephthalate thin films on a electrode via ALD‐MLD. The electrochemical evaluation demonstrates favorable lithium‐ion kinetics and reduced electrolyte decomposition. Overall, the films deposited through ALD‐MLD exhibit promising features as flexible and protective coatings for high‐energy lithium‐ion battery electrodes, offering potential contributions to the enhancement of advanced battery technologies and supporting the growth of the EV and stationary battery industries.

Engineering strategies for high‐voltage LiCoO2 based high‐energy Li‐ion batteries

AbstractTo drive electronic devices for a long range, the energy density of Li‐ion batteries must be further enhanced, and high‐energy cathode materials are required. Among the cathode materials, LiCoO2 (LCO) is one of the most promising candidates when charged to higher voltages over 4.3 V. However, high‐voltage LCO materials are confronted with severe surface and bulk issues inducing poor cyclic stability. To completely unleash the potential of LCO cathodes, a more comprehensive theoretical understanding of the underlying issues is necessary, along with active exploration of previous modifications. This paper mainly presents the degradation mechanisms of LCO under high voltage, the formation and evolution mechanisms of the cathode electrolyte interface, and the surface engineering strategies employed to enhance the cell performance. By organizing and summarizing these modifications, this work aims to establish associations among common research issues and to suggest future research priorities, thus facilitating the rapid development of high‐voltage LCO.

Amphoteric Supramolecular Nanofiber Separator for High‐Performance Sodium‐Ion Batteries

The separator is an essential component of sodium‐ion batteries (SIBs) to determine their electrochemical performances. However, the separator with high mechanical strength, good electrolyte wettability and excellent electrochemical performance remains an open challenge. Herein, a new separator consisting of amphoteric nanofibers with abundant functional groups was fabricated through supramolecular assembly of natural polymers for SIB. The uniform nanoporous structure, remarkable mechanical properties and abundant functional groups (e.g. −COOH, −NH2 and −OH) endow the separator with lower dissolution activation energy and higher ion migration numbers. These metrics enable the separator to lower the barrier for desolvation of Na+, accelerate the migration of Na+, and generate more stable solid electrolyte interphase (SEI) and cathode electrolyte interphase (CEI). The battery assembled with the amphoteric nanofiber separator shows higher specific capacity and better stability than that assembled with glass fiber (GF) separator.

Achieving Uniform Li Deposition and Suppressed Electrolyte Flammability in Li-Metal Batteries via Designing Localized High-Concentration Electrolytes.

The increasing need for energy storage devices with high energy density has led to significant interest in Li-metal batteries (LMBs). However, the use of commercial electrolytes in LMBsis problematic due to their flammability, inadequate performance at low temperatures, and tendency to promote the growth of lithium dendrites and other flaws. This study introduces a localized high-concentration electrolyte (LHCE) that addresses these issues by employing non-flammable electrolyte components and incorporating carefully designed additives to enhance flame retardancy and low-temperature performance. By incorporating additives to optimize the electrolyte, it is possible to attain inorganic-dominated solid electrolyte interphases on both the cathode and anode. This achievement results in a uniform deposition of lithium, as well as the suppression of electrolyte decomposition and cathode deterioration. Consequently, this LHCE achieve over 300 stable cycles for both LiNi0.9Mn0.05Co0.05O2||Li cells and LiCoO2||Li cells, as well as 50 cycles for LiNi0.8Mn0.1Co0.1O2 (NCM811||Li) pouch cells. Furthermore, NCM811||Li cells maintain 84% discharge capacity at -20°C, in comparison to the capacity at room temperature. The utilization of this electrolyte presents novel perspectives for the safe implementation of LMBs.

Balancing Ionic and Electronic Conduction at the LiFePO4 Cathode–Electrolyte Interface and Regulating Solid Electrolyte Interphase in Lithium‐Ion Batteries

AbstractRecently, in electric mobilities and stationary energy storage device applications, the development of long‐lasting, low‐cost, and high‐safety lithium‐ion batteries (LIBs) is widely studied. LiFePO4 (LFP) is a core cathode material for LIBs owing to its cost‐effectiveness and high safety. However, it exhibits low electronic conductivity and sluggish Li+ diffusion, hindering the application of LFP cathodes in high‐power battery industries. Herein, a triazole‐motivated electrolyte additive, 1‐(trimethylsilyl)−1H‐benzotriazole (TMSBTA) is presented, for mitigating iron dissolution via HF scavenging, reinforcing the robustness of the solid electrolyte interphase and constructing a cathode–electrolyte interface (CEI) to balance the ion and electron conduction of the CEI on the LFP cathode. Scanning probe microscopy performed in the conductive atomic force microscopy mode indicates that the electronically conductive CEI created by the oxidative decomposition of TMSBTA enables rapid and homogeneous lithiation and delithiation during cycling without morphological changes in the LFP particles. This study elucidates the design principles of the CEI on the LFP cathode and is expected to guide integrated electrolyte additive engineering for LFP‐containing LIBs.

Enhancing High Voltage Stability via Fluorination of Functionalized Metal Organic Framework Electrolyte in Lithium Metal Batteries

AbstractThe electrolyte stability under high‐voltage conditions considerably limits the upper cut‐off potential of solid‐state electrolytes (SSEs) and therefore the energy density of all‐solid‐state batteries (ASSBs). In this work, metal‐organic frameworks (MOFs) were fluorinated to lower the energy level of HOMO orbital and allow access to a 4F‐MOF that exhibit enhanced anodic stability. The composited 4F‐MOF/PEO electrolyte could not only transport Li+ ions in the ordered framework channels, but also provide a remarkable high‐voltage stability up to 5.0 V, shielding oxidative decomposition that would otherwise occur at around 3.9 V for conventional PEO electrolytes. In addition, stable lithium deposition was demonstrated for more than 1,300 hours at 0.1 mA ⋅ cm−2, while reversible charge‐discharge cycling performance was delivered in assembled Li||LiNi0.5Mn1.5O4 (LNMO) ASSBs up to 5.0 V. Post‐mortem X‐ray photoelectron spectroscopy (XPS) investigation on cathodes revealed presence of a LiF‐rich cathode electrolyte interface (CEI), supporting promoted stability towards high‐voltage ASSBs.

Revealing the origin of enhanced structural stability for nickel-rich LiNi0.83Co0.11Mn0.06O2 cathodes in situ modified with multifunctional polysiloxane

Multifunctional polysiloxane (MPS) layer is elaborately constructed on the surface of LiNi0.83Co0.11Mn0.06O2 (NCM83) particles via in situ hydrolysis-polycondensation of tetraethyl orthosilicate. Impressively, optimal NCM83 (NCM83-2) electrode covered with average 7 nm-thickness of fresh MPS layer delivers improved capacity retention ratio of 81.8 % after 150 cycles at 25 °C and retains the value of 78.7 % after 200 cycles at 60 °C and 1.0 C. Moreover, NCM83-2 electrode presents lower polarization degree with sluggish growth of the capacity platform. The significant advantages of NCM83-2 can be interpreted by the fact that the MPS layer effectively mitigates microcracks generation by inhibiting phase transition and lattice oxygen loss. Moreover, the MPS protective layer suppresses the thickening of cathode electrolyte interphase film and boosts the structural stability of NCM83 electrode to optimize electrochemical properties. Therefore, this strategy may provide promising enlightenments for preserving structural integrity and improving interfacial stability of nickel-rich cathodes for lithium-ion batteries.

Constructing Nano-Interlayer Inhibiting Interfacial Degradation toward High-Voltage PEO-Based All-Solid-State Lithium Batteries.

The interfacial instability between PEO-based solid electrolyte (SPE) and high-voltage cathode materials inhibits the longevity of high-energy-density all-solid-state polymer lithium metal batteries (ASSPLBs). Herein, for the first time it is demonstrated, that contact loss caused by gas generation from interfacial side reactions between the high-voltage cathode and solid polymer electrolyte (SPE) can also arise in ASSPLBs. To alleviate the interfacial side reactions, a LiNb0.6Ti0.5O3 (LNTO) layer is well coated on LiNi0.83Co0.07Mn0.1O2 (NCM83), denoted as (CNCM83). The LNTO layer with low electronic conductivity reduces the decomposition drive force of SPE. Furthermore, Ti and Nb in the LNTO layer spontaneously migrate inside the NCM83 surface to form a strong Ti/Nb─O bond, stalling oxygen evolution in high-voltage cathodes. The interfacial degradation phenomena, including SPE decomposition, detrimental phase transition and intragranular cracks of NCM83, and void formation between cathode and SPE, are effectively mitigated by the LNTO layer. Therefore, the growth rate of interfacial resistance (RCEI) decreases from 37.6 Ω h-0.5 for bare NCM83 to 2.4 Ω h-0.5 for CNCM83 at 4.2V. Moreover, 4.2V PEO-based ASSPLBs achieve impressive cyclability with high capacity retention of 135 mAh g-1 (75%) even after 300 cycles at 0.5 C.

A dual-functional electrolyte additive for stabilizing the solid electrolyte interphase and solvation structure to enable pouch sodium ion batteries with high performance at a wide temperature range from −30 °C to 60 °C

An electrolyte containing a sodium difluorophosphate (NaDFP) dual-functional additive is developed to enhance the temperature performance of NaNi0.33Fe0.33Mn0.33O2 (NFM)/hard carbon (HC) sodium-ion batteries (SIBs). The addition of NaDFP in the electrolyte not only induces solid electrolyte interphases (SEIs) and cathode electrolyte interphases with excellent properties on the anode and cathode surfaces but also optimizes of the solvation structure of sodium ions, resulting in a better cycle stability of NFM/HC SIBs over a wide temperature range from −30 °C to 60 °C. In addition, high capacity retentions of 85 % after 700 cycles at 25 °C, 90 % after 150 cycles at −10 °C and 90 % after 150 cycles at 45 °C are achieved, respectively. And those common problems such as gas generation and sodium evolution of pouch NFM/HC SIBs are also effectively relieved, indicating the promising application prospect of NaDFP additive in the functional electrolyte of NFM/HC SIBs.

Dynamically constructing robust cathode-electrolyte-interphase on nickel-rich cathode by organic boron additive for high-performance lithium-ion batteries

Nickel-rich ternary cathode materials LiNi0.8Co0.1Mn0.1O2 (NCM811) have attracted broad attention due to their high voltage and high energy density for lithium-ion batteries. However, rapid capacity decay due to unstable particle surface inhibit the application. Artificial cathode electrolyte interface (CEI) is undoubtedly a more effective and simpler way to solve this issue. Here, stable and highly conductive in situ CEI is designed using a low-cost organic boron additive isopropoxy-4,4,5,5-tetramethyl-1,3,2-dioxaborolane (ITD). Higher occupied molecular orbital energy endows ITD ability to participate in forming CEI. ITD-contained CEI can reduce nickel dissolving, resulting in a lower self-discharge rate, which is benefit from the uniform and stable CEI on the NCM811 surface. As expected, ITD-based CEI can restrain NCM811crystal cracking in Li||NCM811 half batteries, improving capacity retention from 29.4 % to 93.0 % after 200 cycles at 1C (1C = 200 mA g−1). It is worth mentioning that ITD–derived CEI is conducive to ion migration, which improve the rate capacity retention from 91.5 % to 95.5 %.

Hydrated Calcium Vanadate Nanoribbons with a Stable Structure and Fast Ion Diffusion as a Cathode for Quasi-Solid-State Zinc-Ion Batteries.

We demonstrated the use of hydrated calcium vanadate (CaV6O16·3H2O, denoted as CaVO-2) as a cathode for aqueous zinc-ion batteries (AZIBs). Nanoribbons of hydrated calcium vanadate facilitated shortening of the Zn2+ transport distance and accelerated zinc-ion insertion. The introduction of interlayer structure water increased the interlayer spacing of calcium vanadate and as a "lubricant". Ca2+ insertion also expanded the interlayer spacing and further stabilized the interlayer structure of vanadium-based oxide. The density functional theory results showed that the introduction of Ca2+ and structured water could effectively improve the diffusion kinetics, resulting in the rapid transport of zinc ions. As a result, AZIBs based on the CaVO-2 cathode offered high specific capacity (329.6 mAh g-1 at 200 mA g-1) and fast charge/discharge capability (147 mAh g-1 at 10 A g-1). Impressively, quasi-solid-state zinc-ion batteries based on the CaVO-2 cathode and polyacrylamide-cellulose nanofiber hydrogel electrolytes maintained an outstanding specific capacity and long cycle life (162 mAh g-1 over 10 000 cycles at 5 A g-1). This study provided a reliable strategy for metal-ion insertion and the structural water introduction of oxides to produce a high-quality cathode for ZIBs. Meanwhile, it provides ideas for the combination of vanadium-based materials and gel electrolytes to construct solid-state zinc-ion batteries.

Quenching-Induced Ultrathin LiF-Rich Interphases on LiNi0.8Co0.1Mn0.1O2 Cathode

Nickel-rich layered oxides (NCM) are a promising contender material for the cathode electrode of high-energy lithium-ion batteries (LIBs) due to their large reversible capacity and high operating voltage. However, the poor surface/interfacial stability and the dissolution of transition metal ions hinder the commercial application of NCM. To create an artificial cathode electrolyte interphase (CEI) with LiF-rich inorganic phase on the NCM surface, a practical and efficient way of quenching the NCM powder from high temperature in 1,1,2,2-Tetrafluoroethyl 2,2,2-trifluoroethyl ether (HFE) was devised. With this artificial CEI film, the side reactions between NCM and electrolytes are inhibited, and the dissolution of TM ions is retarded. The quenched-NCM achieved fantastic cycling performance and suppressed voltage decay. Our research offers an efficient and worthy approach for improving the surface/interfacial stabilization of nickel-rich cathode materials for high-energy-density LIBs.

Asymmetric reactors as an innovative approach for optimum microbial fuel cells performance

Microbial fuel cells (MFCs) exhibit asymmetric overpotentials and redox potentials/rates at the cathode and anode. However, the impact of this asymmetric on power density and anode microbial community remains poorly understood. In this study, asymmetric reactors were designed for H-type MFCs to investigate this configuration. Contrary to the initial expectation of increased MFC power output with larger cathode volumes, it was unexpectedly found that the small-cathode reactor outperformed the large-cathode reactor, achieving a 61 % increase in maximum power density. Electrochemical characterization revealed a slightly lower charge transfer resistance (29.34 Ω) in the small-cathode reactor with carbon-felt anode biofilm in PBS. Moreover, 16S rRNA sequence analysis showed that the small-cathode reactor harbored a higher proportion of anaerobic bacteria (83 %), lower species diversity, and a higher abundance of exoelectrogens. Additionally, higher abundances of key gene modules (top eight), such as quinone oxidoreductase and citrate cycle, were observed in the small-cathode reactor. The anode biofilms in both reactors also synthesized some vitamins, such as menaquinone and thiamine. Furthermore, compared to the large-cathode reactor, each set of the small-cathode reactor saved ¥ 20, 23 g of borosilicate, and 55 mL of cathode electrolytes. This study sheds light on the interplay between reactor conformation and performance, contributing to the development of low-cost, high-performance MFCs for real field conditions.

Long‐Life High‐Voltage Sodium‐Ion Batteries Enabled by Electrolytes with Cooperative Na+‐Solvation

AbstractStabilizing the electrode interphases is urgently required to enhance the lifetime of high‐voltage sodium‐ion batteries (SIBs). However, the continuous anode solid–electrolyte interphase (SEI) growth associated with electron leakage and the fragile cathode–electrolyte interphase (CEI) lead to capacity fade at high voltage; and yet the solvation‐interphase‐performance relationship is inadequately addressed. Herein, a cooperative Na+‐solvation strategy is reported to stabilize the interphases by a holistic design of electrolytes combining soft and moderate co‐solvents. The rationally regulated Na+‐solvation leads to CEI/SEI with the desired thickness and component stability. As such, remarkable cycling stability is achieved for 4.3‐V Na3V2O2(PO4)2F (NVOPF) cathodes with 83.3% capacity retention over 3000 cycles at 1 C, significantly outperforming the carbonate counterpart (41.6% capacity retention). Meanwhile, the restrained SEI growth via reducing the formation of electron‐leaking Na2CO3 stabilizes the long‐term cycling of the hard carbon (HC) anode. The assembled NVOPF||HC full cells achieve superior rate capability (up to 15 C) and stable cycling stability over 500 cycles. The demonstrated engineering of electrolyte chemistry, Na+‐solvation, and interphase structure/component contributes toward the rational establishment of design rules for high‐voltage SIBs and possibly other similar chemistries.

Functionalization of Cathode–Electrolyte Interface with Ionic Liquids for High-Performance Quasi-Solid-State Lithium–Sulfur Batteries: A Low-Sulfur Loading Study

We introduce a quasi-solid-state electrolyte lithium-sulfur (Li–S) battery (QSSEB) based on a novel Li-argyrodite solid-state electrolyte (SSE), Super P–Sulfur cathode, and Li-anode. The cathode was prepared using a water-based carboxymethyl cellulose (CMC) solution and styrene butadiene rubber (SBR) as the binder while Li6PS5F0.5Cl0.5 SSE was synthesized using a solvent-based process, via the introduction of LiF into the argyrodite crystal structure, which enhances both the ionic conductivity and interface-stabilizing properties of the SSE. Ionic liquids (IL) were prepared using lithium bis(trifluoromethyl sulfonyl)imide (LiTFSI) as the salt, with pre-mixed pyrrolidinium bis(trifluoromethyl sulfonyl)imide (PYR) as solvent and 1,3-dioxolane (DOL) as diluent, and they were used to wet the SSE–electrode interfaces. The effect of IL dilution, the co-solvent amount, the LiTFSI concentration, the C rate at which the batteries are tested and the effect of the introduction of SSE in the cathode, were systematically studied and optimized to develop a QSSEB with higher capacity retention and cyclability. Interfacial reactions occurring at the cathode–SSE interface during cycling were also investigated using electrochemical impedance spectroscopy, cyclic voltammetry, and X-ray photoelectron spectroscopy supported by ab initio molecular dynamics simulations. This work offers a new insight into the intimate interfacial contacts between the SSE and carbon–sulfur cathodes, which are critical for improving the electrochemical performance of quasi-solid-state lithium–sulfur batteries.

Complex reaction mechanisms of electrolyte decomposition at large-scale Ni-rich Li-ion battery cells including electrode crosstalk effect

Ni-rich cathodes are essential for the advancement of high-energy lithium-ion batteries but encounter significant challenges at elevated voltages, including oxygen liberation and enhanced surface reactivity, which precipitate electrolyte decomposition. This study explores the intricate reaction mechanisms of electrolyte decomposition linked to the pronounced release of oxygen from the cathode lattice in large-scale 18650 cylindrical cells employing Ni-rich LiNi0.90Mn0.05Co0.05O2(NMC90)//graphite configurations, focusing on electrode crosstalk effects at high voltages. Notably, acetals such as methoxy methanol (49.93 %) and methane diol (50.07 %) were identified at 4.7 V, with their presence escalating at 4.9 V. Formaldehyde, present at 7.21 %, along with methanol (22.77 %), methane diol (36.35 %), and methoxy methanol (33.67 %), begins to manifest at 4.9 V. The dissolution of transition metals was analyzed using Inductively Coupled Plasma Atomic Emission Spectrometry, and changes in the double-layer capacitance were assessed through electrochemical impedance spectroscopy, further validating the link between these decomposition products and cathode failure associated with oxygen release. These insights reveal the complex relationship between electrolyte decomposition and cathode degradation due to oxygen release, highlighting a critical failure mechanism in large-scale cylindrical lithium-ion batteries.

Low‐Strain and High‐Energy KVPO4F Cathode with Multifunctional Stabilizer for Advanced Potassium‐Ion Batteries

KVPO4F with excellent structural stability and high operating voltage has been identified as a promising cathode for potassium‐ion batteries (PIBs), but limits in sluggish ion transport and severe volume change cause insufficient potassium storage capability. Here, a high‐energy and low‐strain KVPO4F composite cathode assisted by multifunctional K2C4O4 electrode stabilizer is exquisitely designed. Systematical electrochemical investigations demonstrate that this composite cathode can deliver a remarkable energy density up to 530 Wh kg−1 with 142.7 mAh g−1 of reversible capacity at 25 mA g−1, outstanding rate capability of 70.6 mAh g−1 at 1000 mA g−1, and decent cycling stability. Furthermore, slight volume change (~5%) and increased interfacial stability with thin and even cathode–electrolyte interphase can be observed through in situ and ex situ characterizations, which are attributed to the synergistic effect from in situ potassium compensation and carbon deposition through self‐sacrificing K2C4O4 additive. Moreover, potassium‐ion full cells manifest significant improvement in energy density and cycling stability. This work demonstrates a positive impact of K2C4O4 additive on the comprehensive electrochemical enhancement, especially the activation of high‐voltage plateau capacity and provides an efficient strategy to enlighten the design of other high‐voltage cathodes for advanced high‐energy batteries.

Double additive electrolyte solvation engineering to achieve long cycle and high capacity sodium-ion battery

Sodium-ion batteries are a promising energy storage system due to their rich sodium resources and many other advantages. However, its development is severely hampered by the electrolyte's low compatibility with the electrode contact. Herein, we propose a solvation control strategy with ethoxy (pentafluoro) cyclotriphosphazene (PFPN) and NaClO4 double additives to reconstruct the solvation structure of sodium ions in electrolytes. This enables the electrolyte to form a dense and stable solid electrolyte interlayer (SEI) and double-layer cathode electrolyte interphase (CEI) on the surface of the electrode material to achieve long-cycle and high-capacity sodium-ion batteries. PFPN can form a stable SEI rich in inorganic components at the anode interface. ClO4- can first reach the cathode surface to create a NaCl and polymer-like chain CEI with sodium ions and solvents, and then the PFPN derivatives are migrated to the cathode surface to open the ring and decompose, thus forming a double-layer stable CEI. Therefore, the PEDN electrolyte can simultaneously improve the interface stability of the battery's cathode and anode solid electrolyte. Hence, the capacity retention rate of the 4.5 Ah Na3Fe2(PO4)P2O7 (NFP)||hard carbon (HC) pouch cell after 2500 cycles at 1C is 88.26%.

High-Entropy Oxides for Rechargeable Batteries.

High-entropy oxides (HEOs) have garnered significant attention within the realm of rechargeable batteries owing to their distinctive advantages, which encompass diverse structural attributes, customizable compositions, entropy-driven stabilization effects, and remarkable superionic conductivity. Despite the brilliance of HEOs in energy conversion and storage applications, there is still lacking a comprehensive review for both entry-level and experienced researchers, which succinctly encapsulates the present status and the challenges inherent to HEOs, spanning structural features, intrinsic properties, prevalent synthetic methodologies, and diversified applications in rechargeable batteries. Within this review, the endeavor is to distill the structural characteristics, ionic conductivity, and entropy stabilization effects, explore the practical applications of HEOs in the realm of rechargeable batteries (lithium-ion, sodium-ion, and lithium-sulfur batteries), including anode and cathode materials, electrolytes, and electrocatalysts. The review seeks to furnish an overview of the evolving landscape of HEOs-based cell component materials, shedding light on the progress made and the hurdles encountered, as well as serving as the guidance for HEOs compositions design and optimization strategy to enhance the reversible structural stability, electrical properties, and electrochemical performance of rechargeable batteries in the realm of energy storage and conversion.

CuF2@C composites with inhibited side-reactions enables enhanced electrochemical performance in thermal batteries

Conversion-type compounds as cathodes for thermal batteries have recently attracted considerable attention due to their excellent specific capacities. CuF2 has been regarded as a promising candidate owing to its high theoretical discharge voltage (3.55 V, vs Li) and theoretical capacity (528 mAh·g−1). However, mass loss caused by side-reactions from CuF2 cathode and molten salt electrolyte leads to severe degradation of the discharge capacity of single-cells in thermal batteries. As a proof-of-concept, in this work, carbon coated CuF2 (CuF2@C) is employed as the cathode to fabricate thermal batteries, in which carbon serves as a protector to inhibit the mass loss of CuF2 in molten salt electrolyte. As a result, CuF2@C demonstrates obviously improved electrochemical performance with a discharge specific capacity of 462.45 mAh·g−1 at the current density of 10 mA·cm−2, which is 82.67 % higher than that of the counterpart (bare CuF2). This can be attributed to the reduced average polarization resistance of the single-cells in CuF2@C composites. This work provides a new route for developing high performance CuF2-based cathode material for thermal batteries and promoting its further practical application.