Auxiliary Heating System Research Articles

Numerical simulation of a forced circulation solar water heating system

This study presents a sophisticated numerical simulation model for a forced circulation solar water heating system (FC-SWHs), specifically designed for the unique climatic conditions of Algeria. The model aims to cater to the hot water needs of single-family houses, with a daily consumption of 246 L. Utilizing a dynamic approach based on TRNSYS modeling, the system’s performance in Ain Temouchent’s climate was scrutinized. The model’s validation was conducted against literature results for the collector outlet temperature. Key findings include a maximum monthly average outlet temperature of 38 °C in September and a peak cumulative useful energy gain of 250 W in August. The auxiliary heating system displayed seasonal energy consumption variations, with the highest rate of 500 kJ/hr in May to maintain the water temperature at 60 °C. The energy input at the storage tank’s inlet and the consistent high-level energy output at the hot water outlet were analyzed, with the former peaking at 500 W in May. The system ensured an average water tank temperature (hot, middle and bottom) and water temperature after the mixer, suitable for consumption, ranging between 55 °C and 57 °C. For applications requiring cooler water, the mixer’s exit temperature was maintained at 47 °C. The study’s key findings reveal that the TRNSYS model predicts equal inlet and outlet flow rates for the tank, a condition that is particularly significant when the system operates with high-temperature water, starting at 55 °C. The flow rate at this temperature is lower, at 7 kg/hr, while the water mass flow rate exiting the mixer is higher, at 10.5 kg/hr. In terms of thermal performance, the system’s solar fraction (SF) and thermal efficiency were evaluated. The results indicate that the lowest average SF of 54% occurs in July, while the highest average SF of over 84% is observed in September. Throughout the other months, the SF consistently stays above 60%. The thermal efficiency of the system varies, ranging from 49 to 73% in January, 43–62% in April, 48–66% in July, and 53–69% in October. The novelty of this research lies in its climate-specific design, which addresses Algeria’s solar heating needs and challenges. Major contributions include a thorough analysis of energy efficiency metrics, seasonal auxiliary heating demands, and optimal system operation for residential applications, supporting Algeria’s goal of sustainable energy independence.

Assessment of a LPG hybrid solar dryer assisted with smart air circulation system for drying basil leaves

The fluctuation of solar radiation throughout the day presents a significant obstacle to the widespread adoption of solar dryers for the dehydration of agricultural products, particularly those that are sensitive to high temperatures, such as basil leaf drying during the winter season. Consequently, this recent study sought to address the limitations of solar-powered dryers by implementing a hybrid drying system that harnesses both solar energy and liquid petroleum gas (LPG). Furthermore, an innovative automatic electronic unit was integrated to facilitate the circulation of air between the drying chamber and the ambient environment. Considering the solar radiation status in Egypt, an LPG hybrid solar dryer has been developed to be suitable for both sunny and cloudy weather conditions. This hybrid solar dryer (HSD) uses indirect forced convection and a controlled auxiliary heating system (LPG) to regulate both temperature and relative humidity, resulting in increased drying rates, reduced energy consumption, and the production of high-quality dried products. The HSD was tested and evaluated for drying basil leaves at three different temperatures of50, 55, and 60 °C and three air changing rates of 70, 80, and 90%, during both summer and winter sessions. The obtained results showed that drying basil at a temperature of 60 °C and an air changing rate of 90% led to a decrease in the drying time by about 35.71% and 35.56% in summer and winter, respectively, where summer drying took 135–210 min and winter drying took 145–225 min to reach equilibrium moisture content (MC). Additionally, the effective moisture diffusivity ranged from 5.25 to 9.06 × 10− 9 m2/s, where higher values of effective moisture diffusivity (EMD) were increased with increasing both drying temperatures and air change rates. Furthermore, the activation energy decreased from 16.557 to 25.182 kJ/mol to 1.945–15.366 kJ/mol for the winter and summer sessions, respectively. On the other hand, the analysis of thin-layer kinetic showed that the Modified Midilli II model has a higher coefficient of determination R2, the lowest χ2, and the lowest root mean square error (RMSE) compared to the other models of both winter and summer sessions. Finally, the LPG hybrid solar dryer can be used for drying a wide range of agricultural products, and it is more efficient for drying medicinal plants. This innovative dryer utilizes a combination of LPG and solar energy, making it efficient and environmentally friendly.

Recent advance progress of HL-3 experiments

Abstract Since the first plasma realized in 2020, a series of key systems on HL-3 (known as HL-2M before) tokamak have been equipped/upgraded, including in-vessel components (the first wall, lower divertor, and toroidal cryogenic/water-cooling/baking/glow discharge systems, etc.), auxiliary heating system of 11 MW, and 28 diagnostic systems (to measure the plasma density, electron temperature, radiation, magnetic field, etc.). Magnet field systems were commissioned firstly for divertor plasma discharges. During the 2nd experimental campaign of HL-3 tokamak, several great progresses have been achieved. Firstly, the successful operation with plasma current larger than 1 MA was achieved under a divertor configuration. Secondly, the advanced divertor concept with two distinct snowflake configurations was realized. It is found that the distribution of ion saturation current and heat flux on bottom plate becomes wide due to magnetic surface expansion, demonstrating the advantage of such configuration in the heat flux mitigation. In addition, using the combination of NBI, ECRH and LHCD, the standard sawtoothing high confinement mode of megampere plasma was firstly accessed on the HL-3. The successful commissioning of HL-3 is beneficial for the initial operation of ITER.

Strategic Management of Egyptian-African Geothermal Power Plant Project 60-MW Associated with Sustainable Development in Kenya

Abstract This paper presents the role of Egyptian government for satisfying sustainable development in African countries. However, Egypt has no geothermal power plant although there are many locations in eastern region of Egypt have sufficient quantity of geothermal energy resources. When the highest temperature of geothermal energy resources in Egypt is 51 °C, then it needs auxiliary heating system to produce electricity. So, Egyptian government uses geothermal energy resources as direct use in central heating system for agricultural applications or in physical therapy for encourage tourism sector in Egypt. Development of the African natural resources is considered the most important strategy of Egyptian Government and sharing African countries to obtain sustainability. Kenya is considered the unique country in Africa which utilizes geothermal energy resources for producing electricity. Geothermal Development Company GDC, Nairobi, Kenya produces 985 MW of electricity depending on geothermal energy resources in Kenya and this make Kenya in rank of sixth greatest country in the world utilizes geothermal energy resources for producing electricity after United States, Indonesia, Philippines, Turkey and New Zealand, respectively.

Development of an auxiliary heating system for a solar dryer in Bangladesh

AbstractSolar dryers are a convenient option for drying fruits and vegetables, but they largely depend on climatic conditions. Climate dependency makes them vulnerable to dry products and maintain the quality of the products accurately. To mitigate this problem, an electric auxiliary heating system (AHS) was designed, constructed, and tested for a solar dryer in Bangladesh. The developed system had three parts: an auxiliary heating unit, an air duct, and hot air convection pipes. The performance testing of the AHS was done in three experimental trials. The average air velocity from the auxiliary heating unit was found to be between 3.57 and 3.80 m s−1. Trial runs showed a maximum drying temperature of 66.97°C, while the average value remained between 35.10 and 43.26°C. During the off‐sunshine hours, the AHS rose the average temperature by 1.00–12.84°C above ambient and continued the drying operation. Overall, the solar dryer with AHS saved 30%–36% sunshine hours than open sun drying, and its efficiency was estimated as 14.55%–21.9%. Regression analysis showed that the Page and Modified Page models were suitable for predicting the drying kinetics of cabbage samples. Through the results of the study, the developed AHS showed potential for significantly improving the solar drying process. It could be an effective measure for establishing a weather‐independent drying solution to reduce the postharvest losses of perishable agro‐products. Further improvements to the auxiliary heating unit, implying an Internet of Things (IoT)‐based control system will facilitate an improved and user‐convenient drying operation.Practical ApplicationsPostharvest losses are prevalent for perishable agricultural products (fruits and vegetables) in Bangladesh and are considered a prime reason for the inhabitants to consume a less nutritious diet than recommended. An appropriate dry chain technology that is affordable, weather‐independent, continuous, and fast in operation could be the optimal solution to this problem. Numerous types of solar hybrid dryers with different additional heating sources (electricity, biomass, LPG, etc.) have been investigated around the world. However, the extent of these research endeavors is very limited in Bangladesh. The study was thus conducted to develop a novel auxiliary heating system for a solar dryer in Bangladesh and check its technical viability. Our results indicate that an electric auxiliary heating system can be an efficient option for drying fruits and vegetables irrespective of the weather and can substantially reduce postharvest losses in Bangladesh.

Observation of alpha-particles in recent D–T experiments on JET

The fusion reaction between deuterium and tritium, D(T,n)4 He is the main source of energy in future thermonuclear reactors. Alpha-particles (4 He-ions) born with an average energy of 3.5 MeV transferring energy to the thermal plasma during their slowing down, should provide the self-sustained D–T plasma burn. The adequate confinement of α-particles is essential to provide efficient heating of the bulk plasma and steady burning of a reactor plasma. That is why the fusion-born α-particle studies have been a priority task in the second D–T experiments (DTE2) on the Joint European Torus (JET) to understand the main mechanisms of their slowing down, redistribution and losses and to develop optimal plasma scenarios. JET with Be-wall and W-divertor, enhanced auxiliary heating systems and improved energetic-particle diagnostic capabilities, producing significant population of α-particles, provided the possibility for comprehensive studying of the α-particle behaviour. Selected results of the confined and lost α-particle measurements, evidence of α-particle self-heating and assessments of the fusion performance are presented in this paper giving an opportunity for further modelling and extrapolation to the International Thermonuclear Experimental Reactor and burning plasma reactors.

Thermal design for enhanced temperature uniformity on spark plasma sintering device

Spark plasma sintering (SPS) is a widely used technique for sintering thermoelectric devices. In this process, the heat generated by Joule heating is primarily transferred to the die surface through radiative heat transfer, causing temperature non-uniformity within the specimen. These discrepancies in temperature distribution cause localized changes in the properties of the thermoelectric device, which presents significant engineering challenges in managing heat transfer during the sintering process. This study proposes a thermal design approach to reduce the temperature gradient within the specimen in the existing SPS device. The idea of the auxiliary heating system was evaluated using numerical simulation validated with experimental comparison. Design variables, heating power (an operating parameter) and heater depth (a geometric parameter), were chosen to balance the amount of Joule heating to the heat produced by the auxiliary heating system. The optimization process with sensitivity analysis led to the selection of an auxiliary heating system capable of reducing the temperature gradient within 61.1 K/m. This achievement allows for the sintering of thermoelectric devices with enhanced thermoelectric performance.

Opportunities and Barriers of Calibrating Residential Building Performance Simulation Models Using Monitored and Survey-Based Occupant Behavioural Data: A Case Study in Northern Spain

The performance gap caused by occupant behaviour (OB) is one of the main challenges to the accuracy of building performance simulations (BPS) models. Calibration of BPS models has shown great improvements in tertiary and single residential buildings. Nevertheless, the calibration in collective residential buildings is still uncertain. This study aims to identify the opportunities and barriers to the calibration of collective residential building BPS models for the analysis of heating energy consumption. For this, the research calibrates a real case study of a social rental housing building located in northern Spain. The method involves the adjustment of input data based on OB clusters, developed by monitorization and survey data and the statistical comparison of the results of normative models, calibrated models and real data. The results show an average improvement of 67% in hourly indoor temperature and 16% in hourly heating energy consumption in calibrated models, but still with a considerable performance gap. The main barriers to a higher accuracy are the wide diversity and lack of uniformity of OB patterns, uncertainty of parameters, and use of auxiliary heating systems. However, deeper monitorization and survey campaigns with the use of OB clusters can be a promising opportunity.

Harnessing Solar Energy: A Novel Hybrid Solar Dryer for Efficient Fish Waste Processing

Facing severe climate change, preserving the environment, and promoting sustainable development necessitate innovative global solutions such as waste recycling, extracting value-added by-products, and transitioning from traditional to renewable energy sources. Accordingly, this study aims to repurpose fish waste into valuable, nutritionally rich products and extract essential chemical compounds such as proteins and oils using a newly developed hybrid solar dryer (HSD). This proposed HSD aims to produce thermal energy for drying fish waste through the combined use of solar collectors and solar panels. The HSD, primarily composed of a solar collector, drying chamber, auxiliary heating system, solar panels, battery, pump, heating tank, control panel, and charging unit, has been designed for the effective drying of fish waste. We subjected the fish waste samples to controlled drying at three distinct temperatures: 45, 50, and 55 °C. The results indicated a reduction in moisture content from 75.2% to 24.8% within drying times of 10, 7, and 5 h, respectively, at these temperatures. Moreover, maximum drying rates of 1.10, 1.22, and 1.41 kgH2O/kg dry material/h were recorded at 45, 50, and 55 °C, respectively. Remarkable energy efficiency was also observed in the HSD’s operation, with savings of 79.2%, 75.8%, and 62.2% at each respective temperature. Notably, with an increase in drying temperature, the microbial load, crude lipid, and moisture content decreased, while the crude protein and ash content increased. The outcomes of this study indicate that the practical, solar-powered HSD can recycle fish waste, enhance its value, and reduce the carbon footprint of processing operations. This sustainable approach, underpinned by renewable energy, offers significant environmental preservation and a reduction in fossil fuel reliance for industrial operations.

Heat transfer analysis and structure optimization of unit of flat plate based on a response surface test: An experimental teaching perspective in higher education

The Flat Plate is a common component of solar photothermal experiment and an important teaching tool in the new energy teaching experiment. Aiming at the problem of low heat transfer efficiency and poor teaching effect of traditional roll-bond flat plate, this paper conducts a numerical simulation study on the flow and heat transfer characteristics in the ”Y” -shaped channel unit. The four parameters of width, length, runner parting angle and runner width are used as control variables to optimize the heat transfer structure of the runner. Taking the ”Y” -shaped channel unit as the research object, the finite element model of conjugate heat transfer was established by using Fluent. Through numerical simulation analysis, it is concluded that in the defined length and width interval, the thermal efficiency increases first and then decreases with the increase of the length of the heat transfer unit, and the pressure drop coefficient has a negative correlation with the length and width of the unit. The runner width has a positive correlation with the thermal efficiency and a negative correlation with the pressure drop coefficient. Then, according to the Box-Behnken principle, a response surface test for heat transfer optimization was designed, an optimization model with thermal efficiency and pressure drop coefficient as the response indicators was established, and the optimal element design scheme was determined. The optimization results show that when the subunit length of the heat transfer runner is 40 mm, the width is 35 mm, the parting angle is 60°, and the runner width is 11 mm, the thermal efficiency of the ”Y”-shaped runner is 0.782, and the pressure drop coefficient is 0.121. Finally, a direct-expansion solar auxiliary heating system is built to test the scheme. The experimental results show that the collector using the ”Y”-shaped channel shows better solar energy utilization, which increases the COP of the system by 15.2%. This study provides a reference for the design and optimization of other types of flow channels to improve the heat transfer efficiency of the roll-bond flat plate. Through optimization, the system has innovated in the experimental mode, effectively made up for the shortcomings in the training of new energy professionals, and enriched and developed the experimental theory system and teaching methods of higher education of energy and power majors.

Development and evaluation of a hybrid smart solar dryer.

A hybrid smart solar dryer (HSSD) based on indirect forced convection and a controlled auxiliary heating system was developed, fabricated, and tested to be convenient for sunny and cloudy weather conditions. The achievements of the developed dryer focus on controlling the temperature of the dryer, increasing the drying rate, reducing energy consumption, and providing high-quality products. The HSSD was tested and evaluated for drying basil and sage herbs at 30, 40, and 50°C. The results showed that the fresh basil and sage leaves of 1kg with a moisture content of 84.7% and 75.53% (wet basis) were dried within 58, 46, 32 and 38, 28, and 20h at 30, 40, and 50°C, respectively. Correspondingly, the traditional drying methods achieved 96h outdoors and 144h indoors at room temperature. The average of the fabricated flat-plate solar collector efficiency (thermal efficiency, ηfpsc ) was ranged from 49.18%±9.52% to 66.02%±2.8%. The highest drying rates were achieved with the HSSD method. Moreover, the HSSD method led to a remarkable saving in energy with values ranging from 25.54% to 77.1% versus the traditional drying methods. While the best quality in terms of essential oil content and microbial load for the dried basil and sage herbs was achieved by the HSSD at 40°C. Finally, the HSSD is a promising energy-efficient method where it can save 70% of energy consumption, thus reducing the carbon footprint of drying processes, and providing higher quality products compared to the conventional methods.

Dynamic characteristics and energy efficiency evaluation of a novel solar seasonal thermal storage - heating system

This paper proposes solar seasonal thermal energy storage system compounded with long-term and short-term energy storage tanks for a single-family dwelling, which using assisted water source heat pump to further improve the systems stability. With the objective of improving the solar energy utilization efficiency and reducing the primary energy consumption, the dynamic simulation model of the “heat collection-heat storage-heat supply” system under the non-stationary boundary conditions throughout the year is established. The energy transfer and conversion law of each subsystem and the dynamic operation characteristics are analyzed through simulation method. The system cooperative control strategy is proposed and parameter optimization is carried out. Results indicate that the annual heat collection efficiency of the water source heat pump composite system has been improved by 2.2 % compared with the electric auxiliary heating system. Meanwhile, the heat storage efficiency and the solar energy guarantee rate increased by 5.8 % and 8.3 %, respectively. Moreover, the optimal water source heat pump composite system not only improves energy efficiency and achieves the cost savings compared with the electric auxiliary heating system, but also reduces carbon dioxide emission by 10.3 %, which have great advantages for energy saving and emission reduction.

Performance of a solar greenhouse-biogas hybrid dryer for dehydration of water hyacinth (Eichhornia crassipes)

The development of a solar greenhouse dryer combined with an anaerobic digester for biogas production can reduce carbon emissions and create zero waste. This paper presents the performance of a solar greenhouse biogas dryer (SGBD) that burns biogas to supplement the drying of water hyacinth. The SGBD has an overall efficiency of 87% for 100 kg of fresh water hyacinth. The auxiliary heating system enabled the SGBD to achieve drying temperatures of 24.5 to 45.0 degrees during cloudy and rainy days and produce high quality dried products. There was a fivefold increase in drying capacity and a reduction in drying time of six hours (38%) using the SGBD. End users of the dried product judged it to have improved consistency in color and shape. The SGBD cost less than US$3800 to build with a payback period of five months. This design demonstrates a low-cost and simple technology for small businesses.

Fast ion generation by combined RF-NBI heating in W7-X

Good fast ion confinement in quasi-isodynamic stellarators still has to be demonstrated experimentally. In the absence of fusion alphas, auxiliary heating systems can be used to generate fast ions. For this purpose, W7-X has neutral beam injection and its newly installed ion cyclotron heating system. In practice, both systems can run simultaneously, the synergetic running of both is the focus of the current modelling development. With the upgrades to the SCENIC code described here, we find that, compared with pure neutral beam injection (NBI), the fast ion tail is significantly enhanced when radio frequency (RF) heating is enabled. But the effectiveness of heating and fast ion tail generation strongly depends on the plasma parameters and antenna frequency, which calls for further study, both numerical and experimental.

A newly constructed Linear Experimental Advanced Device LEAD

The Linear Experimental Advanced Device (LEAD) has been constructed for comprehensive studies on plasma turbulence, plasma-material interaction and new techniques for tokamaks at Southwestern Institute of Physics (SWIP). The vacuum vessel of this linear device is 3055 mm long. It consists of three parts, i.e. the source chamber, the linear magnetized confinement chamber and the plasma-material interaction (PMI) chamber. Kinds of plasma sources, including radio-frequency (RF) sources and a hot cathode source, have been developed to produce steady-state plasma. Wave-mode helicon plasmas can be excited by a large-size four-ring-antenna RF source when the input power is higher than 180 W. The typical electron density is higher than 1019/m3. Transfer from distinct narrowband drift waves to broadband turbulence is observed by means of adjusting the axial magnetic field, which makes LEAD a suitable device to investigate plasma turbulence. Auxiliary heating systems, including a 2.45 GHz Electron Cyclotron Resonance and an ion heating source, and a 1.5 MV ion accelerator are to be installed on LEAD. It promises a particle flow of over 1023/m2s and a heat load of several MW/m2, which makes LEAD a suitable platform for not only fundamental plasma physics but also PMI research.

The Application of a Solar–Air-Source Heat Pump Dual-Supply Heating System in a High-Cold Area in China

Solar energy is the most available renewable resource and has great potential for various applications. Solar heat pumps are limited when operating alone due to weather and the unstable and intermittent nature of solar energy. The idea of combining a solar collector with an air-source heat pump (ASHP) is proposed to solve the problems. Taking solar energy and air energy as the heat source of the system can improve the heat collection efficiency and heating performance coefficient of the dual-supply heating system in realizing the efficient and stable operation of the whole unit. This study investigated the application of a solar–air-source heat pump (S/AS-HP) dual-supply heating system for a residential building in Lhasa and compared the winter work performance and economic benefits of three different heating forms: solar–air-source heat pump, air-source heat pump, and solar–electric auxiliary heating systems. A simulation model was established and analyzed using the measurement data. The results show that during the heating period, the temperature of the primary side water supply is stable at about 60 °C, and the total operating hours of the solar collector period accounted for 26.9% of the total hours, of which 23.16% were independent operating hours. The average COPsys of the solar–air-source heat pump is 4.21, which greatly improves work performance compared with other systems, and the annual cost is the lowest among the three forms for the same service life at 41,824.6 CNY, saving 9.6% and 35.1% per year compared with the air-source heat pump system and the solar–electric auxiliary heating system. Considering conditions in alpine regions, S/AS-HP systems are the optimal heating solution for single buildings.

Thermal Performance and Energy Analysis of Phase Change Material-Integrated Building with the Auxiliary Heating System in Different Climate Regions

Phase change material (PCM) embedded in the building contributes to enhancing indoor thermal comfort and reducing the heating load in winter by absorbing/releasing solar energy. The application effects of PCM incorporated into a single-space passive solar building with the auxiliary heating system (AHS) were investigated numerically in the six representative regions of western China. In the calculation and analysis by the enthalpy model, it was found that the effectiveness of PCM greatly depended on local climate conditions, thickness, and location of PCM. The results indicated that it was necessary to adopt the AHS for winter heating of the passive solar building. On this basis of using AHS, it showed a favorable thermal energy storage effect after the application of PCM resulting in the minimum indoor air temperature being maintained above 15°C within the comfort range stably. The integrated discomfort degree in each region was decreased by more than 96% compared to the original building, and the average temperature in Lhasa was 2°C higher than that in Urumqi. Furthermore, the highest rate of energy saving and carbon dioxide emission saving in the six regions was 19.7% and 17.4% in Lhasa, and the lowest were 4.3% and 4.2% in Urumqi, while other regions were relatively close, respectively. As a result, it can be stated that for a passive solar building using the AHS during the heating period, PCM was the most suitable for application in Lhasa, unsuitable in Urumqi, and generally suitable in other regions.

Dynamic modeling and control of a solar-powered Brayton cycle using supercritical CO2 and optimization of its thermal energy storage

Recompression Brayton cycles using supercritical CO2 as the working fluid appear as a prominent alternative for thermo-solar power applications. Also, solar energy's natural variability and intermittence make it difficult for solar plants to operate consistently and predictably. Thus, two of the most explored mitigating alternatives are thermal energy storage and auxiliary heating systems. Hence, this paper used actual meteorological data and transient numerical simulations to investigate the power output dynamics of a 10 MW plant. The modeling of an active control system of the working fluid mass inventory allowed the plant to operate in a stable manner while accounting for the significant variations in the fluid's thermophysical properties. Also, the study investigated the effect of the sizes of the thermal energy storage system and solar collectors field on the dynamics of the system. Finally, statistical analyses with actual meteorological data from Florianopolis/Brazil for nine days between 2017 and 2018 supported determining the optimal thermal energy storage system size. Hence, depending on the daily conditions, the results showed the operating settings that minimize the use of auxiliary heating with reductions of fuel consumption larger than 10%.

Feasibility study of neutral beam injection in Thailand Tokamak-1

Thailand Institute of Nuclear Technology (TINT) is developing Thailand Tokamak-1 (TT-1) from a former device HT-6 M of China. The first hydrogen plasma will be initiated in 2023. To investigate high-β plasma and physics related to fast ions, TT-1 will be equipped with auxiliary heating systems. In this work, a feasibility study for installing a neutral beam injection (NBI) heating system in TT-1 is carried out. This work is motivated to characterize beam ion's orbits in different injection angles and to explore a condition suitable in terms of higher heating efficiency. In this work, we assume that a hydrogen beam will be launched into the TT-1 plasma with an acceleration voltage of 20 kV. The orbit simulations using the gyromotion following code LORBIT are performed in various magnetic field equilibria, i.e., different plasma current (Ip), toroidal magnetic field strength (Bt), and the magnetic axis (Rax). Furthermore, beam ions are injected in different directions, i.e., tangential co-injection and tangential counter-injection. In the case of co-injection, beam ion loss is not significant, by about 6%, whereas beam ion loss fraction is evaluated to be 26–34% in the case of counter-injection. Also, it is found that the number of lost beam ions is significantly affected by changing Ip and Rax. The results obtained in this work will directly support the experiment plan for the high-performance plasmas, design of the fast-ion diagnostic system, and systematic understanding of beam ion's confinement property and beam-ion-driven magnetohydrodynamic (MHD) instabilities in TT-1.

Feasibility study on solar coupled gas-fired boiler heating system retrofit in residential buildings in the HSCW zone of China

Residential buildings in the hot summer and cold winter (HSCW) zone rely on gas-fired boiler for heating have a certain application basis, but high operating costs and limited gas consumption seriously limit the promotion of gas-fired boiler. To reduce domestic gas consumption in Wuhan, two solar auxiliary gas-fired boiler heating systems formed in parallel and series are proposed and explore the feasibility of coupled heating system retrofit. The simulation models of two solar coupled gas-fired boiler heating systems are established by TRNSYS, and the results indicate that the indoor thermal environment of the two systems is good and the temperature of the tank is stable. The solar fraction of the parallel system reaches 24.40%, which has better energy saving. The optimization analyses display that the system has the best economy when the collector area ratio is 10.0%, and the collector area and tank volume ratio is 8/0.7. The solar-assisted parallel heating system retrofit can save 2.02 × 104 MJ over the entire life cycle, and the increased initial investment can be recovered within 4.75 years. The research results can provide a basis and new ideas for the heating retrofit of the gas-fired boiler in residential buildings in the HSCW zone.