Power Amplifier Output Research Articles

Modeling and numerical simulation optimization of output spectrum of thulium-doped broadband fiber optic light source

In this research, the performance of thulium-doped fiber lasers is analyzed and a mathematical model is established. Thulium-doped fiber amplifiers are the focus of this article. A large number of simulations have been carried out in the MATLAB simulation environment, and the main work and innovation points are as follows: firstly, the energy level structure characteristics of thulium were studied, and its spectral characteristics were analyzed. After consulting some information, 3H4 to 3H6 energy level has been selected in modeling. Secondly, use the rate equations and the power propagation equations to provide a theoretical analysis of the pumping mode of thulium-doped fiber lasers. And a mathematical model of a thulium-doped fiber laser was established. The parameters such as fiber length and doping concentration in the model are discussed. Finally, to find the appropriate parameters, the genetic optimization algorithm is used to optimize the fiber length and doping concentration, and then we can get the parameters corresponding to the maximum output power of the thulium-doped fiber amplifier.

Achromatic elastic metalens for high-performance confocal piezoelectric energy harvesting

In this study, we analytically, numerically, and experimentally investigated a high-performance confocal piezoelectric energy harvesting system. We achieved a significantly enhanced electrical performance through a Mikaelian lens, which achromatically focuses ambient elastic waves, resulting in the formation of a highly amplified strain energy field in the piezoelectric energy harvester. Previous studies on piezoelectric energy harvesting platforms have limitations, such as the focal position changing with operating frequencies and impedance mismatching owing to inclusions or holes. To address these problems, we utilized the self-focusing ability based on the conformal mapping theory and achromatic ability based on the Kirchhoff–Love thin plate theory to design our Mikaelian lens-based piezoelectric energy harvesting platform. The proposed platform demonstrates a remarkable elastic wave focusing ability at an identical focal position for a broad frequency range. The experimentally visualized wave fields matched well with the numerically calculated full-wave harmonic simulation results. We achieved highly amplified output power up to 1.44 mW within a broad range from 40 to 60 kHz out of the same focal point owing to confined elastic wave energy; the output power extracted at this confocal position was up to 3.76 times higher than that extracted at the lens start position. Our highly performance and broadband achromatic piezoelectric energy harvesting platform lays an attractive foundation for designing potential applications, such as wireless sensing, structural health monitoring, and biomedical devices.

185–215 GHz CMOS Frequency Doubler with a Single Row Staggered Distribution Layout Design

This paper presents a 220 GHz × 2 amplifier–doubler chain composed of a rat-race balun, a 6-stage driver amplifier, and a frequency doubler. The presented amplifier–doubler chain was fabricated in commercial 40 nm bulk CMOS technology. The maximum cutoff frequency fmax for the NMOS transistor produced by this manufacturing process was 290 GHz. The saturation output power of the six-stage driver amplifier at 110 GHz was 11.5 dBm. The transistor of the frequency doubler consisted of a single-row interleaved Poly-Diffusion Contact balancing structure. Theoretically, the single-row interleaved Poly-Diffusion Contact balancing structure was able to effectively avoid parasitic components. The simulated results demonstrate that the presented structure achieves a higher output than the conventional designs. Based on these measured results, the presented amplifier–doubler chain provides a peak output power of 7.9 dBm at 200 GHz and a 3-dB bandwidth of 30 GHz. Based on the comparison with other reported results, the presented amplifier–doubler chain provides the highest output power among reported frequency doublers fabricated in CMOS technology.

SBS suppression using PRBS phase modulation with different orders.

The Brillouin instability (BI) caused by stimulated Brillouin scattering (SBS) can limit the output power of high-energy laser amplifiers. Pseudo-random bitstream (PRBS) phase modulation is an effective modulation technique to suppress BI. In this paper, we study the impact of the PRBS order and modulation frequency on the BI threshold for different Brillouin linewidths. PRBS phase modulation with a higher order will break the power into a larger number of frequency tones with a lower maximum power in each tone, leading to a higher BI threshold and a smaller tone spacing. However, the BI threshold may saturate when the tone spacing in the power spectra approaches the Brillouin linewidth. For a given Brillouin linewidth, our results allow us to determine the order of PRBS beyond which there is no further improvement in the threshold. When a specific threshold power is desired, the minimum PRBS order required decreases as the Brillouin linewidth increases. When the PRBS order is too large, the BI threshold deteriorates, and this deterioration occurs at smaller PRBS orders as the Brillouin linewidth increases. We investigate the dependence of the optimal PRBS order on the averaging time and fiber length, and we did not find a significant dependence. We also derive a simple equation that relates the BI threshold for different PRBS orders. Hence, the increase in BI threshold using an arbitrary order PRBS phase modulation may be predicted using the BI threshold from a lower PRBS order, which is computationally less time-consuming to compute.

Scalable Single-Input Behavioral Modeling Architecture for MIMO Systems With Crosstalk

The inherent nonlinear behavior exhibited by power amplifiers (PAs) in saturation mode is a major impediment in wireless systems to achieve higher power efficiency, and higher spectral efficiency. Although PA behavioral modeling and digital predistortion (DPD) techniques are widely utilized at transmitter to characterize and linearize such distorted nonlinear output of PAs, the nonlinear distortions with memory effects have become more severe due to simultaneous strong crosstalk between multiple PA branches in multiple-input multiple-output (MIMO) arrays. Furthermore, current multi-input behavioral models suffer from a sharp increase in number of coefficients as the number of transmitter path increases in MIMO. In overcoming these challenges, we propose a decomposed cross-correlation based single-input-single-output (CC-SISO) behavioral modeling architecture. The proposed solution utilizes a low-cost, novel cross-correlation based method to estimate and cancel the simultaneous nonlinear and reverse crosstalk from multiple PA branches. Once the crosstalk is mitigated, the MIMO DPD can be implemented with single-input DPD blocks which significantly reduces the complexity. Furthermore, CC-SISO DPD eliminates the requirement for signal feedback paths before and after the PA, and thus reduces overall hardware implementation complexity. Through simulations, we demonstrate that the proposed CC-SISO architecture can reduce the overall complexity of state-of-art multi-input DPD models for MIMO systems.

Load and Power Indexed Predistortion for Improved Robustness to MIMO Channel Conditions

This letter presents an effective digital predistortion (DPD) solution to the problem of channel-dependent variations in the linearity of multiple-input-multiple-output (MIMO) transmitters. Such variations arise because: 1) conventional MIMO precoding results in large disparities in the average-power levels across chains and 2) antenna crosstalk causes significant active load modulation at the power amplifier (PA) output. Consequently, PA nonlinearity is channel dependent and cannot be compensated using static DPD. In this work, we propose a DPD solution that is a function of the estimated average reflection coefficient at the antenna as well as the PA average input power, which thus accounts for the channel conditions and antenna crosstalk. The proposed solution is validated through experiments on a MIMO transmitter prototype across varying channel conditions.

Microwave Frequency Doubler with Improved Stabilization of Output Power

The passive multipliers based on semiconductor diodes, most frequently a Schottky type, should be driven by a certain value of input power, where the conversion losses are optimal. This means that the variation in the input power level causes the change in the output power level. A solution to this issue is the integration of an output power amplifier, which in the state of saturation provides quasi-stabilization of the output power. Practically, this approach gives an unsatisfactory performance: weak stabilization or narrow input power range. This paper comprises a concept of an active frequency multiplier with the use of one FET transistor and a special adaptive bias circuit in order to obtain a very wide input power range when the output power is stable. The principle of the operation, design guidelines, and measurement results have been presented for an example circuit of the frequency doubler. The results show the possibility to obtain up to 10 dB input power range for a 1 dB change in output power level without the use of additional amplifiers.

Over 250 W low noise core-pumped single-frequency all-fiber amplifier.

A high-power linearly-polarized all-fiber single-frequency amplifier at 1 µm based on tandem core-pumping is demonstrated by using a large-mode-area Ytterbium-doped fiber with a core diameter of 20 µm, which nicely balances the stimulated Brillouin scattering effect, thermal load, and output beam quality. A maximum output power of more than 250 W with a corresponding slope efficiency of >85% is achieved at the operating wavelength of 1064 nm without being constrained by the saturation and nonlinear effects. Meanwhile, a comparable amplification performance is realized with a lower injection signal power of the wavelength near the peak gain of the Yb-doped fiber. The polarization extinction ratio and the M2 factor of the amplifier are respectively measured to be >17 dB and 1.15 under the maximal output power. In addition, by virtue of the single-mode 1018 nm pump laser, the intensity noise of the amplifier under maximal output power is measured to be comparable to that of the single-frequency seed laser at frequencies higher than 2 kHz, except for the emergence of parasitic peaks that can be eliminated by optimizing the driving electronics of the pump lasers, while the deterioration of the amplification process to the frequency noise and linewidth of the laser is negligible. To the best of our knowledge, this is the highest output power of a single-frequency all-fiber amplifier based on the core-pumping scheme.

Over 30 W single-frequency all-fiber amplifier at 1120 nm with high ASE suppression.

A 1120nm linearly polarized all-fiber single-frequency amplifier based on Yb-doped fiber (YDF) is reported. A maximum output power of 30W is achieved by 976nm clad-pumping and 1018nm core-pumping, with corresponding slope efficiencies of 51.9% and 70.0%, respectively. With the 976nm clad-pumping configuration, a signal to amplified spontaneous emission (ASE) ratio of more than 45dB is realized at maximum output power. The polarization extinction ratio of the amplifier is measured to be more than 21dB in the whole power scaling process. In addition, the intensity noise of the amplifier at maximum output power is also characterized to be around -130d B c/H z at frequencies above 2kHz and is comparable to that of the seed laser. Moreover, the deterioration of frequency noise and linewidth of the amplified laser is negligible. To the best of our knowledge, this is the highest output power of a single-frequency all-fiber amplifier that exploits the fundamental transition of YDF at 1120nm, even without any external intervention for suppressing ASE in the short wavelength range.

High Power Ytterbium-Doped Fiber Lasers Employing Longitudinal Vary Core Diameter Active Fibers

Thanks to the advantage of balancing nonlinear effects and transverse mode instability, vary core diameter active fiber (VCAF) has been widely used in high power ytterbium-doped fiber lasers in recent years. Up to now, VCAF has developed from the basic form of the original tapered fiber to the spindle-shaped and saddle-shaped fiber with different characteristics and has been applied in conventional fiber lasers, oscillating–amplifying integrated fiber lasers, and quasi-continuous wave fiber lasers and successfully improved the performance of these lasers. In the present study, a 6110 W fiber laser amplifier is realized based on a tapered fiber. The maximum output power of a fiber laser amplifier based on spindle-shaped fibers is 6020 W with a beam quality of M2~1.86. In this paper, we first introduce the basic concept of VCAF and summarize its main fabrication methods and advantages in high-power fiber laser applications. Then, we will present the recent research results of high-power fiber laser employing VCAF in our group and clarify the outstanding advantages of VCAF compared with the constant core diameter active fiber (CCAF).

A General Digital Predistortion Linearization Scheme for Hybrid Beamforming System

Hybrid beamforming multiple-input multiple-output (MIMO) system has attracted a lot of attention in recent years since it significantly reduces the hardware cost compared to the fully digital beamforming system. However, with hybrid beamforming, the one-to-one mapping between the radio frequency (RF) chain and the nonlinear power amplifier (PA) is destroyed. The PA nonlinearity cannot be compensated by conventional digital predistortion (DPD) algorithms. In this article, we propose a novel multiple-input DPD model for hybrid beamforming MIMO systems. An extra digital compensation block is introduced in the feedback path. With the feedback compensation block, the proposed DPD can linearize the PA output signal as well as the aggregated far-field signal. What is more, we propose a DPD estimation algorithm with much reduced complexity. Comparing to existing solutions, the proposed scheme achieves satisfactory performance for hybrid beamforming system. It does not rely on the measurement of the channel or the assumption of massive antennas. Simulation results demonstrate the effectiveness of the proposed DPD scheme.

A Deep Learning Receiver for Non-Linear Transmitter

Non-linearity of wireless transceivers, specifically power amplifier (PA) non-linearity, could pose major limitations towards having high throughput, and cost and energy efficient wireless communication systems. Such limitations from the PA is typically compensated in the transmitter, e.g. by applying power back-off or performing digital-pre-distortion (DPD) aiming to linearize the transmitter. However, applying PA power back-off leads to lower energy efficiency, and lower output power, and hence lower coverage; and performing DPD results in higher complexity of the transmitters. This paper presents an alternative approach based on a receiver method to perform signal detection in the presence of distortions due to PA non-linearity. We propose a receiver technique using artificial neural networks (ANN) to compensate for the PA non-linearity at the receiver side. The paper presents link-level simulation results using pre-trained neural network models based on synthesized training data. The simulation results confirm that the designed receiver can tolerate higher distortions, hence allow the PA output power back-off to be reduced, leading to higher output power improving coverage, spectral efficiency, energy efficiency, and throughput.

Digital Signal Recovery With Transmitter Nonlinear State Tracking for Satellite Communications

This brief proposes a digital signal recovery (DSR) method to compensate the nonlinear distortion introduced by power amplifiers (PAs) under dynamic nonlinear operating states. Unlike conventional PA linearization methods that extract the nonlinearity based on the baseband I/Q PA input and output signal samples, the proposed method attempts to derive the memory polynomial (MP) model parameters based on PA operating states using a deep neural network (DNN). This method allows the receiver to achieve DSR by tracking the operating states of the PA effectively with a few telemetry data. Validation results from simulations and experiments based on a GaN PA operating at 3.5 GHz reveal that the proposed method can maintain satisfactory DSR performance in terms of adjacent channel power ratio (ACPR) and error vector magnitude (EVM) while the transmitter PA is operating with fluctuating average input/output power, supply voltage, and bias voltage. The training data size and time are further reduced by using a transfer learning (TL) approach.

A 2 nJ/bit, 2.3% FSK Error Fully Integrated Sub-2.4 GHz Transmitter With Duty-Cycle Controlled PA for Medical Band

This paper proposed a fully integrated MBAN (2360–2400 MHz) continuous phase modulated transmitter (TX) with tunable less than 0dBm output power for medical band. A duty-cycle tuning strategy was proposed for the power amplifier (PA) featuring adaptive optimized efficiency for different output powers. A fully on-chip transformer-based match network was proposed to suppress the 2nd harmonic using a series <inline-formula xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink"> <tex-math notation="LaTeX">$LC$ </tex-math></inline-formula> resonator and to suppress the 3rd harmonic by introducing a transformer inter-winding capacitor feedback path. A fractional-N all-digital phase locked loop (ADPLL) with a transformer-based digitally controlled oscillator (DCO) is employed to reduce power consumption as well as improve modulation quality. The transmitter was fabricated in 40-nm CMOS technology, occupying an active area of 0.48mm2. Experimental results show a 26% drain efficiency with −10dBm PA output and 4dB tunable range. A 2mW total power consumption was measured with a TX efficiency of 5% and an energy efficiency of 2nJ/bit. The measured 2nd and 3rd harmonic distortion of the output were −44.3dBm and −57.2dBm, respectively, with on-chip matching network. The measured FSK error of CPM was 2.3% with an M of 2 and 1.57% with an M of 4.

Generation of all-fiber ultrafast pulses at 2 μm by soliton self-frequency shift in highly nonlinear silica fiber

An efficient and straightforward method to obtain all-fiber pulsed sources at 2 μm is presented and experimentally demonstrated. It is based on the soliton self-frequency shift effect in a highly nonlinear fiber. The output power of a supercontinuum source is previously increased by an optimized homemade thulium-doped fiber amplifier. By coupling the amplified output power in a highly nonlinear fiber, the spectrum is shifted toward 130 nm and the spectral peak is located at 2014 nm. The power conversion factor reaches values as high as 0.93, without employing additional amplifiers. The mean spectral power of the 2 μm source reaches −4.6 dBm nm−1 (0.35 mW nm−1), its output power is 38 mW and the peak power of each pulse is higher than 27 kW.

A 915 MHz IoT Transmitter Employing Frequency Tripler and Digitally Controlled Duty-Cycle/Phase Calibration

A 915 MHz binary frequency-shift keying (BFSK) transmitter (TX) for Internet-of-Things (IoT) applications is presented. The proposed TX adopts a passive frequency tripler, digital duty-cycle/phase calibration, and a low-cost on-chip power amplifier (PA) matching network (MN). The frequency tripler allows an ultralow-power (ULP) implementation of the frequency synthesizer by lowering the maximum operating frequency and relaxing the frequency tuning range requirement. The proposed frequency tripler provides 10.6 dB better 300 MHz spur reduction compared to that of the conventional frequency tripler by adding a series high-pass filter. The two-phase 20% duty-cycle and single-ended 50% duty-cycle calibration circuits drive the frequency tripler and Class-D PA, respectively, suppressing unwanted spurs significantly. The digital duty-cycle/phase calibration circuits, designed based on the quantitative analysis of the stability, offer advantage of technology scaling. The reduced spur relaxes the harmonic filtering requirement at the PA output, leading to an on-chip PA MN with low- <inline-formula xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink"> <tex-math notation="LaTeX">${Q}$ </tex-math></inline-formula> . Implemented in 55 nm CMOS, the proposed TX shows the peak output power of 5.2 dBm and efficiency of 30.6% over 902–928 MHz while dissipating 210 <inline-formula xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink"> <tex-math notation="LaTeX">$\mu \text{W}$ </tex-math></inline-formula> in the phase-locked loop (PLL) for 0.9 V supply. All spur component levels stay below −41 dBm with the worst harmonic distortion of −48.5 dBc. The proposed TX achieves 100 kbps of data rate for the BFSK modulated signals with the corresponding FSK error of 3.2%.

Training Data Selection and Dimensionality Reduction for Polynomial and Artificial Neural Network MIMO Adaptive Digital Predistortion

In 5G and beyond radios, the increased bandwidth, the fast-changing waveform scenarios, and the operation of large array multiple-input multiple-output (MIMO) transmitter architectures have challenged both the polynomial and the artificial neural network (ANN) MIMO adaptive digital predistortion (DPD) schemes. This article proposes training data selection methods and dimensionality reduction techniques that can be combined to enable relevant reductions of the DPD training time and the implementation complexity for MIMO transmitter architectures. In this work, the combination of an efficient uncorrelated equation selection (UES) mechanism together with orthogonal least squares (OLS) is proposed to reduce the training data length and the number of basis functions at every behavioral modeling matrix in the polynomial MIMO DPD scheme. For ANN MIMO DPD architectures, applying UES and principal component analysis (PCA) is proposed to reduce the input dataset length and features, respectively. The UES-OLS and the UES-PCA techniques are experimentally validated for a <inline-formula xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink"> <tex-math notation="LaTeX">$2 \,\times \, 2$ </tex-math></inline-formula> MIMO test setup with strong power amplifier (PA) input and output crosstalk.

A Study of Power Efficiency Maximization in Submarine Cable Systems

Power efficiency is a key concept in submarine cable transmission systems because of fixed and limited electrical power supplies. Electrical power is provided by a DC voltage applied across the cable from power feed equipment (PFE) located at the terminal ends and is used to power all optical amplifiers throughout the entire link which may be many thousands of kilometers. We examine here via system modeling aspects of power efficiency in the context of maximizing this quantity, primarily with respect to the optimal generalized signal-to-noise ratio (GSNR). We explore the dependence on capacity metric, span loss, link length, and fiber attenuation. We also compare the optimal GSNR predicted using pump power as a measure of power consumption in a single fiber with total cable capacity predicted by application of a pump sharing model and the resulting electrical-to-optical conversion efficiency predicted as a function of amplifier output power, span loss, and repeater power available. We find that the cable capacity measure predicts somewhat higher optimal GSNR than the single fiber measure based on amplifier pump power. The optimal GSNR decreases with longer link length and optimal span loss is somewhat higher than previous results based on different analyses.

Penguat Jembatan dengan Untai Pembalik Fase

The maximum output voltage of the audio amplifier is limited to the magnitude of the power supply voltage of the power transistor or the operational amplifier on the final amplifier. This limits the maximum power of the audio amplifier output. The way to enlarge the output power of the audio amplifier without increasing the voltage is the bridge method or bridged modes. With this method a bridge amplifier will be generated. This Bridge Amplifier is also known as Bridge-Tied Load (BTL) or Bridged Transformerless. The principle of Bridge Amplifiers is to use a pair of final amplifiers whose outputs have opposite phase each other. There are 3 ways to make a pair of power amplifiers have opposing phases: with internal modification, with an audio transformer (phase splitting audio input transformer) and with a simple active phase reversal splitter circuit). This paper will discuss Bridge Amplifiers with simple phase inverting circuits. A pair of audio power amplifiers using two TDA2050 chips which are operated at ± 19 Volt supply voltage. The phase inverting circuit using IC TL072. Sinusoidal signal with an amplitude of 200 mVp and a frequency of 1 KHz is used as an input signal. The results to be observed and measured are gain, input, output and bandwidth of the bridged amplifier compared to the usual amplifier

Design of a broadband Doherty power amplifier with a modified load modulation network

This article proposes a modified load modulation network (LMN) to adjust the structure of the traditional Doherty power amplifier (DPA) by changing one λ/4 microstrip line at the output of the main power amplifier into two in the traditional DPA and connecting a terminal open-circuit λ/2 line at the junction point which can reduce the frequency dispersion effect to achieve expanding bandwidth while maintaining saturation efficiency and back-off efficiency. A 2.6–3.6 GHz DPA is designed and fabricated for verification. The measured results show that the saturated output power is 42.5–44 dBm and the saturated efficiency is between 63% and 69% in target band with a gain from 8.5 to 9.5 dB. At 6 dB output power back-off, the drain efficiency is 44%–50%. And the adjacent channel power ratio (ACPR) is better than −32 dBc.