Agricultural Nozzles Research Articles

Fine-grained method for determining size and velocity distribution patterns of flat-fan nozzle-atomised droplets based on phase doppler interferometer

Pesticides are commonly applied by using agricultural nozzles to generate droplets during delivery process. Initial spray atomization characteristics including droplet size and velocity are important factors that affect the pesticide utilization rate. Exploring efficient methods for atomization measurement is helpful to deeply understanding nozzle sprays. In this study, droplet size and velocity of a flat-fan nozzle were measured with phase doppler interferometry (PDI), and sub-area statistics method was adopted to establish a fitting model for atomization characteristics analyse. The results demonstrated that the distribution patterns and value contrasts of droplet size and velocity in different sub-areas visually reflect the nozzle atomization characteristics under varying spray pressures. The quantized model of droplet size and velocity within spatial sub-areas of spray atomization revealed significant differences in droplet size and velocity at various positions within the atomization area. Near the edge of the initial atomization zone, droplet size increases while velocity exhibits a decreasing trend. Additionally, the coefficient of determination for the x-axis position within the atomization zone, in relation to droplet size and velocity, was above 90%. The PDI with the sub-area statistical method employed in this study offers a fine-grained approach for investigating nozzle atomization characteristics.

Comparison between Liquid Immersion, Laser Diffraction, PDPA, and Shadowgraphy in Assessing Droplet Size from Agricultural Nozzles

Spray droplet diameters play a key role in the field of liquid plant protection product (PPP) application technology. However, the availability of various measurement techniques, each with its unique operating principles for evaluating droplet size spectra, can lead to different interpretations of spray characteristics. Therefore, in this study, four measurement techniques—Liquid Immersion (LI), Laser Diffraction (LD), Phase Doppler Particle Analysis (PDPA), and Shadowgraphy (SG)—were utilized to evaluate the droplet size distribution of agricultural spray nozzles. Additionally, PDPA and SG were used to assess the average velocity of spray droplets. Experiments were conducted in three different laboratories with the main aim of comparing results obtained with various types of equipment utilized under ordinary practical conditions. Spraying tests were carried out using three flat fan nozzles and an air-induction flat fan nozzle. As a general trend, the lowest values for droplet diameters were measured using the Laser Diffraction technique, followed by Shadowgraphy. The PDPA technique provided the highest values for mean diameters (D10, D20, and D30) and the numeric median diameter (Dn0.5), whereas the Liquid Immersion method yielded the highest values for the Sauter mean diameter (D32) and volumetric diameters (Dv0.1, Dv0.5, and Dv0.9). Importantly, all measurement techniques were able to discriminate the four nozzles based on their Dv0.5 diameter. Average droplet velocities showed a similar pattern across the four nozzles with the PDPA and the SG measurement techniques. The differences in diameter values observed with the four measurement techniques underline the necessity of always including reference nozzles in spray quality assessments to base classifications on relative rather than absolute values.

Evaluating of Different Types of Agricultural Nozzles Locally Used in Iraq

The experiment aimed to Manufacture a device for checking the nozzles and testing its efficiency and to study the effect of research factors on the studied traits. The device was manufactured locally through using materials available in the Iraqi market. The system is Both Hydraulic and electronic (ISO 5682-1)1 relay on sensors technology and the test platform was built and designed on a movable trolly at the department of Agricultural Machines and Equipment / College of Agricultural Science / University of Baghdad. The design includes the use of mechanical water pump and electrical AC water pump. The design includes a nozzle holder that can accommodate three nozzles per test. The design also consists of spreading wings and stationary wing that can accommodate 50 vessels and 50 ultra-sonic sensors. All that is controlled by a main control unit which consists of three branch modules (each one of them is responsible to collect and analyze data from several sensors on each of the wings. The idea behind the design is to merge between actual spraying and the use of electronic sensors to analyze the size of the sprayed liquid in each of the vessels, the concept of the design is based upon Volumetric distribution of the liquid. The concept of the device was based on using ultra sonic sensors to measure the volumetric distribution of liquids. The experiment aimed to determine the effects of these factors on flow rate, spraying angle, sprayed area, spraying swath, volumetric distribution (CV), and symmetry. The experiment was conducted at the college of Agricultural science, Baghdad University. The results showed that the spraying pressure had a non-significant effect on flow rate. However, increasing the pressure from 3.0 to 5.0 and then to 7.0 bar resulted in flow rates of 1.314, 1.286, and 1.36 l/m, respectively. The status of the nozzle (new or worn) did not significantly affect the flow rate, with new nozzles registering a slightly higher flow rate of 1.327 l/m compared to worn nozzles (1.312 l/m). On the other hand, the type of nozzle had a significant impact on flow rate, with plastic, brass, and steel nozzles registering flow rates of 1.243, 1.422, and 1.29 l/m, respectively. Regarding the spraying angle, the results indicated that the spraying pressure had a significant effect. Increasing the pressure from 3.0 to 5.0 and then to 7.0 bar resulted in spraying angles of 132, 132, and 136 degrees, respectively. The nozzle status significantly affected the spraying angle, with worn nozzles resulting in a higher angle of 137 degrees compared to new nozzles (130 degrees). However, the type of nozzle did not significantly affect the spraying angle. For the sprayed area, the spraying pressure had a significant effect, with higher pressures resulting in larger sprayed areas. Worn nozzles also significantly increased the sprayed area compared to new nozzles. The type of nozzle had a significant impact on the sprayed area, with plastic, brass, and steel nozzles resulting in areas of 70.4, 80.44, and 89.16 cm2, respectively. The experiment proved that nozzles must be tested periodically, otherwise they start to perform beyond the parameters they were designed to perform with.

Spray drift evaluation with point clouds data of 3D LiDAR as a potential alternative to the sampling method.

Spray drift is an inescapable consequence of agricultural plant protection operation, which has always been one of the major concerns in the spray application industry. Spray drift evaluation is essential to provide a basis for the rational selection of spray technique and working surroundings. Nowadays, conventional sampling methods with passive collectors used in drift evaluation are complex, time-consuming, and labor-intensive. The aim of this paper is to present a method to evaluate spray drift based on 3D LiDAR sensor and to test the feasibility of alternatives to passive collectors. Firstly, a drift measurement algorithm was established based on point clouds data of 3D LiDAR. Wind tunnel tests included three types of agricultural nozzles, three pressure settings, and five wind speed settings were conducted. LiDAR sensor and passive collectors (polyethylene lines) were placed downwind from the nozzle to measure drift droplets in a vertical plane. Drift deposition volume on each line and the number of LiDAR droplet points in the corresponding height of the collecting line were calculated, and the influencing factors of this new method were analyzed. The results show that 3D LiDAR measurements provide a rich spatial information, such as the height and width of the drift droplet distribution, etc. High coefficients of determination (R2 > 0.75) were observed for drift points measured by 3D LiDAR compared to the deposition volume captured by passive collectors, and the anti-drift IDK12002 nozzle at 0.2 MPa spray pressure has the largest R2 value, which is 0.9583. Drift assessment with 3D LiDAR is sensitive to droplet density or drift mass in space and nozzle initial droplet spectrum; in general, larger droplet density or drift mass and smaller droplet size are not conducive to LiDAR detection, while the appropriate threshold range still needs further study. This study demonstrates that 3D LiDAR has the potential to be used as an alternative tool for rapid assessment of spray drift.

Effect of Adjuvant, Concentration and Water Type on the Droplet Size Characteristics in Agricultural Nozzles

One of the goals of adding adjuvants to agricultural spray solutions is to enhance the droplet size characteristics of this spray. Droplet size, in turn, has an influence in the deposited spray quality, in addition to the drift and losses of spray to off-target places. The aim of this research was to evaluate the effect of adding adjuvants to two types of water from different sources on the droplet size characteristics. Two types of adjuvants were employed in the tests: the active substance content of the first adjuvant was a 50% aqueous solution of sodium salt of alkylbenzenesulfonic acid—10% (HY), whereas the second was from rapeseed oil (natural origin)—85% (OL). Both adjuvants were tested in two concentrations: the first was with the concentration recommended by the manufacturer (100%), whereas the second concentration was 50% of the recommended dose. Two types of water from different sources were used in the tests: the first was from a village in the eastern part of Poland (WS), whereas the second was tap water from the city of Lublin, Poland (WUP). Dv0.1, Dv0.5, or volume median diameter (VMD), Dv0.9, Sauter mean diameter (SMD), relative span (RS), and the droplet size distribution were measured and calculated as characteristics of the droplet size. Results showed that the source of water affected the influence of adding adjuvant to the spray solution. Water from the WS source with adjuvant resulted in a numerical decrease in the Dv0.5 values in the percentage of droplet size range below 150 µm, whereas water from the WUP source resulted in an increase in these values (except when adding the HY adjuvant at 50% concentration). Adjuvant concentration significantly (p < 0.05) influenced the features of Dv0.9, SMD, and RS. Adding the OL adjuvant type numerically decreased the percentage of droplet size below 150 µm, and the Dv0.5 values, but only when the WS water source was used.

Evaluation of Different Internal Designs of Hydraulic Nozzles under an Accelerated Wear Test

The use of worn-out agricultural nozzles in pesticide application has a negative effect on the efficiency and cost of the application process. It also has an effect on environmental pollution due to an excessive amount of pesticide being applied when spraying with worn-out nozzles. In this paper, the resistance to wear of three different internal design hydraulic nozzles was ascertained. Changes in the flow rate and spray distribution as a result of this wear were also investigated. The wear test was done inside a closed system, and it was accelerated using an abrasive material to generate 100 h of wear. The tested nozzles were the Turbo TeeJet (TT)-twin chambered, Turbo Twinjet (TTj60)-dual outlet, and Drift Guard (DG)-pre-orifice. Wear rate, flow rate, and the virtual coefficient of variation (CVv) were measured at different wear intervals. The results showed that the TTj60 type was the most resistant to wear, followed by the TT type and DG. The latter two types showed an increase in the flow rate only in the first 45 h of wear. Virtual coefficient of variation (CVv) values were less than 10% after finishing the test (after 100 h of wear) for the three types of nozzles, which are acceptable values according to International Organization for Standardization (ISO) 16122-2, 2015.

Real-time measurement of droplet size and its distribution of an air-induced air-assisted electrostatic nozzle

In this paper, a critical assessment has been carried out to understand the droplet size and its distribution with the variation of various parameters such as applied high voltage, applied air pressure, liquid flow rate, position and orientation of the nozzle. The mean droplet size for an electrostatic nozzle is 15.54 μm which is minimum amongst all four nozzle droplet sizes 24.17, 138.25 and 259.43 μm for a pressure swirl nozzle, a motorized and a handheld agricultural nozzle respectively. Statistical analysis shows that an electrostatic nozzle has the mean of 15.53 μm, standard deviation of 0.1538 and variance of 0.02368.

Modelling Spray Pressure Effects on Droplet Size Distribution from Agricultural Nozzles

For spray applications, drop size is the most important feature as it affects all aspects of a phytosanitary treatment: biological efficacy, environmental pollution, and operator safety. In turn, drop size distribution depends on nozzle type, liquid properties, and working pressure. In this research, three nozzles were studied under ordinary working conditions and the effect of pressure on drop size distribution was assessed. The nozzles under test, all from Albuz (France), were an orange hollow cone nozzle ATR 80 (European color code), an air induction flat spray nozzle AVI 11003, and an air induction hollow cone nozzle TVI 8002. The ATR 80 and the TVI 8002 nozzles were tested at four pressure values: 0.3, 0.5, 1.0, and 1.5 MPa; the AVI 11003 nozzle was tested at 0.3 and 0.5 MPa. The drop size measurement technique was based on the liquid immersion method by using a custom-made test bench; spray quality parameters were computed by means of suitable functions written in R language. Results showed that an increase in working pressure caused an increase in drop pulverization regardless of the type of nozzle, and drop pulverization was higher for the turbulence nozzle than for the two air induction nozzles. Based on skewness and kurtosis values, the theoretical gamma distribution was the most adapt to fit the experimental data. The scale parameter showed a decreasing trend with the increase in the pressure, a clear index of higher drop pulverization.

Effect of geometrical parameters of air-induction nozzles on droplet characteristics and behaviour

Delivering pesticide droplets accurately to a target has always been a challenge for crop spraying. Pesticide spray that drifts or runs-off the crop are major sources of soil and groundwater pollution and encourage pesticide overuse. This study optimised an agricultural air-induction nozzle to overcome these difficulties. Various configurations were designed and manufactured to investigate the geometrical parameters. A range of experiments were designed and carried out to simulate field conditions and examine spray structure, stability, droplet size range, and the probability of microbubbles to determine correlations between droplet size and spray drift and droplet rebound potential with or without entrained microbubbles. The performance of the designed nozzle was compared to that of commercial nozzles. Optical diagnostic methods, including high-speed photography, laser diffraction-based droplet sizing, and microscopic flow visualisation, were employed to perform accurate investigations of droplet size range and microbubble presence potential. In addition, the spatial distribution of spray influenced by lateral wind was investigated in an open-type wind tunnel and measured using a 2-dimensional patternator and water-sensitive papers. The rebound potential of the droplets was investigated using high-speed photography for artificial leaves. The results demonstrate the significance of geometrical design factors on the performance of nozzles and the effectiveness of induced air on the reduction of drift and rebound potential. Droplets including microbubbles were found to distribute across the surface of the target leaves on impact and exhibit increased rebound resistance. • Agricultural nozzles with coarser sprays have less drift potential. • Jet pump geometry controls ALR where the tip V-cut angle controls the spray angle. • Injection pressure enhances the atomization quality and degrades the uniformity. • Droplet air inclusion leads to better coverage. • Larger droplets including air bubbles have less rebound potential.

Development and Prototype Testing of an Agricultural Nozzle Clog Detection Device

HighlightsPrototypes of an agricultural nozzle clog detection system (for 18 nozzles) have been successfully developed.Spray quality characteristics (droplet size, pattern, and coverage) were not significantly affected when testing the device with extended-range nozzles (TeeJet XR8004).Most of the spray quality characteristics were significantly affected when testing the device with ultra low-drift nozzles (John Deere PSULDQ2004).Abstract. Agricultural nozzles are the main components that perform the spraying of agrochemicals, and their proper functionality is a key element for uniform spray application on crops. Because nozzles have small orifices, they can become clogged when there is debris from the agrochemical in the tank. Nozzle clogging during spray application results in poor pest and weed management and increased cost for re-spraying the affected crop row. Measures used to prevent nozzles from clogging include using screens or strainers to filter out debris before it reaches the nozzle tip, as well as performing regular checks on the nozzles. However, nozzle clogging still occurs during spraying despite the precautions taken. Thus, a device that can detect nozzle clogging during spraying is necessary to enable a quicker response that will ensure uniform application across each row of the crop. A novel, patented device for detecting clogged nozzles that is externally attachable to each nozzle on a sprayer boom was developed in the Precision Application Technology Lab at Arkansas State University. The main objective of this article is to present a general description of this prototype nozzle clog detection device and the nozzle clog detection system. Spray droplet size and pattern tests under controlled conditions and spray coverage tests under field conditions were conducted with and without the device to determine if there were significant differences in droplet size, spray pattern, or spray coverage between using and not using the device. The tests demonstrated that this new technology has potential for detecting clogged nozzles without significantly influencing spray quality for extended-range nozzles but not for ultra low-drift nozzles. To increase the reliability of the performance of this new technology, further improvements in the design need to be considered. Keywords: Clogged nozzle, Detection, Droplet size, Prototype device, Spray coverage, Spray pattern.

Analysis of Volume Distribution and Evaluation of the Spraying Spectrum in Terms of Spraying Quality

Assessment of the quality of the operation of agricultural nozzles on the basis of transverse volume distribution and spatial methods of analysis for stream spraying spectra is insufficient, and positive result do not guarantee that the intended and effective spraying effects are obtained. Tests were carried out to assess the quality of nozzles on the basis of transverse volume distribution analysis, microstructure characteristics, and detailed analysis of places where an unexpected change in the nature of the transverse volume distribution (increase in volume) was noted. The subjects of the study were RS11003 flat fan nozzles and a measuring stand equipped with a grooved table, which was used to carry out tests. During the tests, the unit flow rate from the nozzles, the transverse volume distribution of liquids from individual table grooves, and the corresponding CV distribution coefficients of variation were recorded. Detailed tests were carried out for the selected nozzle, consisting of spot measurement of droplet characteristics in individual liquid stream bands. The widths of these bands were constant and equal to the width of the measuring table groove. Measurements were made using analyzer 2D-Laser Doppler Anemometry/Phase Doppler Anemometry (2D-LDA/PDA) from Dantec Dynamics. The analysis of the results obtained from the grooved table and the droplet characteristics in individual stream bands showed clear and unexpected changes in the nature of the transverse volume distribution for all tested nozzles. These changes, consisting of a local increases in droplet diameters (with a reduced number of occurrences), can cause a significant reduction in the quality and effectiveness of spraying, despite the positive fulfillment of generalized normative criteria for their assessment.

Particle Size Characterization of Agricultural Sprays Collected on Personal Air Monitoring Samplers.

Potential inhalation exposure of agricultural workers and bystanders to aerosolized particles emitted by typical agricultural spray nozzles is influenced by the particle size distribution (PSD) of the spray. However, inhalation risk assessments do not currently factor in the human-relevant PSD that may be inhaled during pesticide handling activities. This study was conducted to characterize the PSD of aerosols collected with OSHA Versatile Sampler (OVS) tubes, which are monitoring devices commonly used for inhalation risk assessment in worker exposure studies. An Oxford Lasers N60V particle size analyzer was used for characterizing the spray PSD emitted from various agricultural nozzles. Side-by-side air sampling with OVS tubes and Respicon TM particle samplers was conducted to characterize the size distribution of aerosols collected on the OVS tubes during spraying of a diluted chlorothalonil formulation. Based on this comparison, OVS tubes captured the inhalable fraction (mass median diameter (D50) = 100 μm), with approximately 40% of the total inhalation concentration contributing to systemic exposure (D50 = 10 μm) regardless of nozzle spray quality. In addition, nozzles with fine and medium spray produced higher airborne concentrations compared to nozzles with coarse spray. Thus, the use of modern low-drift nozzles (e.g., air-induction nozzles) that emit larger spray droplets can substantially reduce the airborne concentration levels within inhalable particle size fractions. While the concentrations within these airway fractions (e.g., respirable, thoracic, inhalable) increased from extremely coarse to very fine spray nozzles, the relative proportion of each fraction within the total inhalable concentration remained constant regardless of spray quality or nozzle type. Such information on the PSD of pesticide applications can be used to refine inhalation risk assessments for agricultural workers and bystanders.

Effects of Liquid Viscosity on Agricultural Nozzle Droplet Parameters

To discuss the effects of pesticide viscosity on the atomisation characteristics of an agricultural nozzle, glycerite with different mass fractions was prepared to replace the pesticide. First, the atomisation region of the nozzle was meshed and sized. Second, the speed and kinetic energy of the droplets at different positions in the atomisation region were measured by Phase Doppler Anemometry. The results demonstrated that the Sauter mean diameter, volume mean diameter and arithmetic mean diameter of droplets first decreased and then increased gradually in the axial direction of the atomisation region. Surface waves of a certain pattern were formed on the liquid surface, which was ejected by the disturbance of external air resistance. As the distance increased, the amplitude increased and the wave crest was broken into small droplets. These droplets then collided and agglomerated into large droplets under the effect of gravity. Droplets had an approximately symmetric distribution on the radial direction of the atomisation region, and the droplets were small in the middle and large at the two ends. The droplet size was positively related to the radial distance. Compared with the droplet speed at the two ends, the droplet speed at the axis was higher and the droplet size was smaller. Moreover, the kinetic energy of the droplets along the axial direction decreased sharply and then increased slowly. Droplets with high viscosity at the near end of the nozzle had small kinetic energy, and the effects of liquid viscosity on the atomisation characteristics of a nozzle could not be neglected. The droplet kinetic energy slightly increased at the far end.

Effect of working pressure, fluid temperature, nozzle type and nozzle orifice size, on spray characteristics using viscous feed additive DL-2-hydroxy-4-(methylthio)-butanoic-acid

Liquid ingredients in livestock feed are often added by spraying through commercial agricultural nozzles to a powdery matrix of mash feed. Homogenously distributing these ingredients is of utmost importance to achieve the required quality. This study aimed to evaluate the effect of working pressure, fluid temperature, and nozzle type and orifice size on droplet diameter distributions and spray area, which may influence liquid applications on feed. Optical diagnostics methods were used to study droplet size distributions and spray morphologies. DL-2-hydroxy-4-(methylthio)-butanoic acid, a common liquid additive, was chosen for this study. The spray droplet size distribution was coarser with conditions of low temperature and/or low pressure, while it was finer with high pressure and/or high temperature in a nonlinear way, sometimes giving bimodal distributions. The spray angle decreased strongly with temperature and/or pressure. Flat fan nozzles in this study produced sprays with greater maximum spray angle than the tested full cone nozzle but also with less regular droplet distributions. This work shows the effect that working parameters, and nozzle configuration have on spray morphology, particularly spray angle and volumetric droplet size distributions, and helps in the choice regarding these characteristics to improve spray applications for livestock feed manufacturing.

Role of large inhomogeneities in initiating liquid sheet breakup in agricultural atomisation

It is known that agricultural emulsifiable concentrate (EC) formulations reduce the fraction of fine spray produced during atomisation when compared with water. In recent years researchers inferred why EC formulations spray differently when multiple phases are present. The dispersed phase (e.g., oil drops/solid particles) is responsible for creating holes within the sheet, where the holes grow and merge to form liquid bridge ligaments which stretch and then breakup into droplets. Creating an inhomogeneous formulation of water and oil is a necessary, but not sufficient condition, to reduce the fine droplets produced during atomisation. The dispersed phase must also be of sufficient size and wettability (hydrophobicity) to create holes within the spray sheet emanating from agricultural nozzles. This manuscript describes the mechanics of creating perforations in liquid sheets using inhomogeneities within the spray solution. Perforations alter the sheet breakup mechanism leading to a reduction of very small drops (e.g., driftable fines) when atomised. Therefore, the number and location of perforations within the sheet can be used to control sheet breakup and droplet size distribution upon atomisation, based upon proof-of-concept experimental observations, surface energy minimisation principles, an overview of the various antifoaming agents that have been reported in literature (solids, oil globules, micelles), along with physical mechanisms for hole growth. Understanding the multiphase fluid parameters and atomisation process conditions that lead to hole perforation in liquid sheets (i.e., inhomogeneities) provides the basis for a priori formulation design based solely on physicochemical properties of formulation components.

Measuring Spray Droplet Size from Agricultural Nozzles Using Laser Diffraction

When making an application of any crop protection material such as an herbicide or pesticide, the applicator uses a variety of skills and information to make an application so that the material reaches the target site (i.e., plant). Information critical in this process is the droplet size that a particular spray nozzle, spray pressure, and spray solution combination generates, as droplet size greatly influences product efficacy and how the spray moves through the environment. Researchers and product manufacturers commonly use laser diffraction equipment to measure the spray droplet size in laboratory wind tunnels. The work presented here describes methods used in making spray droplet size measurements with laser diffraction equipment for both ground and aerial application scenarios that can be used to ensure inter- and intra-laboratory precision while minimizing sampling bias associated with laser diffraction systems. Maintaining critical measurement distances and concurrent airflow throughout the testing process is key to this precision. Real time data quality analysis is also critical to preventing excess variation in the data or extraneous inclusion of erroneous data. Some limitations of this method include atypical spray nozzles, spray solutions or application conditions that result in spray streams that do not fully atomize within the measurement distances discussed. Successful adaption of this method can provide a highly efficient method for evaluation of the performance of agrochemical spray application nozzles under a variety of operational settings. Also discussed are potential experimental design considerations that can be included to enhance functionality of the data collected.

Measuring Spray Droplet Size from Agricultural Nozzles Using Laser Diffraction.

When making an application of any crop protection material such as an herbicide or pesticide, the applicator uses a variety of skills and information to make an application so that the material reaches the target site (i.e., plant). Information critical in this process is the droplet size that a particular spray nozzle, spray pressure, and spray solution combination generates, as droplet size greatly influences product efficacy and how the spray moves through the environment. Researchers and product manufacturers commonly use laser diffraction equipment to measure the spray droplet size in laboratory wind tunnels. The work presented here describes methods used in making spray droplet size measurements with laser diffraction equipment for both ground and aerial application scenarios that can be used to ensure inter- and intra-laboratory precision while minimizing sampling bias associated with laser diffraction systems. Maintaining critical measurement distances and concurrent airflow throughout the testing process is key to this precision. Real time data quality analysis is also critical to preventing excess variation in the data or extraneous inclusion of erroneous data. Some limitations of this method include atypical spray nozzles, spray solutions or application conditions that result in spray streams that do not fully atomize within the measurement distances discussed. Successful adaption of this method can provide a highly efficient method for evaluation of the performance of agrochemical spray application nozzles under a variety of operational settings. Also discussed are potential experimental design considerations that can be included to enhance functionality of the data collected.

The Change in Spectrum of Drops in the Exploitation Process of Agricultural Nozzles

Abstract Agricultural nozzles usually produce a different drops size depending on the pressure and the physical condition (work life) of the nozzle besides producing a wide range of the drops spectrum in the spray cloud. In this paper the standard flat fan nozzles were investigated regarding the effect of the working pressure and the nozzle physical condition (new and worn nozzles). The size of drops and the spectrum of drops across the long axis of the spray pattern were examined by using Sympatec GmbH Laser Diffraction. Reducing the working pressure from 3 to 2 and then to 1 caused production of larger drops, also using worn nozzles (especially with lower pressure) changed the drops size which is expected to be produced from the new nozzles. The standard flat fan nozzles produced a wide range of the drops spectrum inside the spray cloud, generally small drops (less than 150 µm) concentrated in the middle of the spray pattern while the big drops (250-350µm) were situated on the edge positions (70 cm from the centerline) of the spray pattern.

The Influence of the Water Quality on the Droplet Spectrum Produced by Agricultural Nozzles

Abstract The aim of the studies was to check if the quality of water, which was taken from different sources, to plant protection treatments influences the change of the droplet size generated by an agricultural nozzle. For the study water taken from 3 different sources was used and demineralized water was used as a reference. The water quality was evaluated as far as its hardness was concerned. Water hardness was measured with a droplet test. One of the most frequently used by farmers type of agricultural nozzle TeeJet VP of the size 110/02 was used in the study. The study was performed in two combinations. One of them was carried out for the pure water and the second one for water with addition of agricultural spray adjuvant Superam 10AL. The measurements were done with three pressure values: 2 bar, 3 bar and 4 bar in three repetitions. The droplet size was measured with a laser diffractometer HELOS/R by Sympatec. The study showed that water hardness did not have any significant influence on the droplet size formed by agricultural nozzles. Adding of agricultural spray adjuvant to the water did not cause any significant change in the droplet size, however, the difference in water hardness caused the decrease of a diameter of formed droplets. The results were compared in a tabular and graphic form. In the next phase of the study for individual types of waters agricultural spray adjuvant was added to check how it influences the change of the size of droplets produced by the nozzles with sliding pressure in the whole range of the stream sprayed by the nozzle.

A comparison of initial spray characteristics produced by agricultural nozzles

Pesticides are commonly applied by using hydraulic nozzles to generate droplets. The properties of these spray droplets can influence the effectiveness and risks associated with the use of pesticides. Initial spray characteristics (initial droplet size and velocity, fan angle and spray liquid density) were therefore measured for a range of hydraulic nozzles and spray mixtures. Particle Image Velocimetry (PIV) was used to measure the spray sheet velocity.There was a significant difference between a standard hydraulic nozzle, Turbo TeeJet® and air induction nozzle for all measured spray characteristics. The standard hydraulic nozzle generated the smallest droplet sizes, the highest velocity and the highest spray liquid density. The air induction nozzle generated the largest droplet size, the slowest velocity and the lowest spray liquid density. The type of air induction nozzle and spray formulation was also found to influence spray characteristics.This work has demonstrated that initial spray characteristics such as droplet size and velocity, liquid density, fan angle and included air can vary depending on nozzle design, operating parameters and spray formulations. Initial droplet velocity was found to be significantly correlated to droplet size (Dv0.5) and spray pressure.