This study is the first to determine the concentration for 17 congeners of polychlorinated dibenzo-p-dioxins and polychlorinated dibenzofurans (PCDD/Fs) and element contamination in poultry that is close to petroleum refinery at Al-Hashemiya Municipality, Zarqa Governorate, Jordan. Ten different samples (chicken) were collected to cover ten different locations of poultry farms in Al-Hashemiya Municipality. These locations are considered polluted areas as a result of exhaust gases produced from the refinery. The 17 PCDD/Fs congeners and elements of Pb, Cd, As, Zn, Cu, Se, Hg, Cr, and Ni were determined for three parts of each sample (liver, muscle, and gizzard). All samples were analyzed for PCDD/Fs after a Soxhlet extraction procedure and cleanup by column chromatography; then, all compounds were identified and determined using GC-MS techniques. The elements were analyzed after digestion and measured using an inductively coupled plasma optical emission spectrometer (ICP-OES) and validated with the Lab Mix24 RM NCS ZC73016 reference material. The highest total sum concentration of PCDD/Fs was found in liver samples to be 214.07 ng/kg (dry weight), while the highest sum of toxicity equivalent to PCDD/Fs of 22.54 ng TEQ/kg was found in gizzard samples. For element concentrations, the highest total sum of 16.89 mg/kg (dry weight) was found in liver samples. The concentration level of the elements of Se, Hg, Cr, and Ni for all parts of the chicken was within an acceptable range according to Jordanian standards and therefore the measured level of heavy and trace elements in the poultry samples (chicken) does not pose a danger to public health. The chickens found in poultry farms near the refinery are more likely to contain a higher concentration of PCDD/Fs congeners due to exhaust gas exposure.

Simultaneous enantioseparation of three commonly used chiral antifungal pesticides (diniconazole, hexaconazole, and imazalil) was first studied based on micellar electrokinetic chromatography (MEKC) with hydroxypropyl-γ-CD (HP-γ-CD) as chiral selector. In this study, the importance of experimental parameters such as chiral selector type and concentration, sodium dodecyl sulfate (SDS) concentration, the ratio of methanol, and separation voltage in optimizing were investigated. The simultaneous enantioseparation of diniconazole, hexaconazole, and imazalil was successfully achieved in 30 mM borate buffer (pH 9.0) containing 10 mM HP-γ-CD and 20 mM SDS with methanol (8%) added as organic modifiers. The resolution of diniconazole, hexaconazole, and imazalil was 15.2, 2.12, and 2.78, respectively, and the peak efficiency (N) was over 566,825 plates/m. This study provides an alternative way to systematically separate chiral antifungal pesticides with high efficiency.

In this study, magnetic mesoporous silica-Fe3O4-graphene oxide nanoparticles (Fe3O4@GO@mSiO2) were synthesized and used as sorbents for magnetic solid-phase extraction (MSPE) of trace amounts of quercetin in natural samples (spinach, green pepper, dill, and red onion). The sorbent produced was characterized by Fourier transform infrared (FTIR), scanning electron microscopy (SEM), energy dispersive X-ray spectroscopy (EDAX), X-ray diffraction (XRD), vibrating sample magnetometry (VSM), and X-ray photoelectron spectroscopy (XPS). The effects of various experimental factors on the percent recovery of quercetin, including extraction time, desorption time, sample solution pH, and adsorbent amount were investigated. The Fe3O4@GO@mSiO2 strategy showed excellent stability and sensitivity for the determination of quercetin, with a suitable linear range of 20-800 µg L-1 and a detection limit of 5.2 µg L-1. The data indicate that Fe3O4@GO@mSiO2 has a specific surface area and suitable adsorption capacity for the determination of quercetin.

Iron-based organic frame material MIL-53 (Fe) was synthesized by the hydrothermal method with Cu2+ incorporated to obtain bimetallic composite MIL-53 (Fe, Cu). The structure and morphology of the material were characterized by SEM, XRD, BET, FTIR, XPS, and zeta potential. The adsorption performance of MIL-53 (Fe, Cu) on methyl orange was tested under a variety of conditions, including the effects of pH and material dosage, by the static adsorption test. The results show that under the condition of pH = 7, a temperature of 30°C, and an adsorbent dosage of 20 mg, the removal rate of MIL-53 (Fe, Cu) for methyl orange can reach more than 96% within 4 h, and the maximum adsorption capacity after fitting by the thermodynamic model can reach 294.43 mg/g, showing the excellent adsorption performance of MIL-53 (Fe, Cu) on methyl orange. In addition, by exploring the adsorption mechanism of MIL-53 (Fe, Cu) on methyl orange, it is found that the adsorption of MIL-53 (Fe, Cu) on methyl orange depends on chemical adsorption, as evidenced by combining Fe3+ and Cu2+ in the material with methyl orange molecules to form complexes to achieve adsorption. While the specific surface area of the material had no obvious effect on adsorption, the effects of pH, temperature, and concentration were explored. At a pH of 6.5, greater adsorption occurred at higher temperatures, as determined by thermodynamic model fitting, as well as with higher initial methyl orange molecule concentration.

Cannabinoid extraction from Cannabis sativa L. (hemp) for nonmedical purposes has become popular in the United States. Concerns, however, have been raised regarding the accuracy of the labels for cannabinoid levels in the commercial products. In this study, we developed rapid, sensitive, selective, accurate, and validated liquid chromatography-tandem mass spectrometry for the quantification of cannabinoids. The methods are for determining 11 cannabinoids in cannabis (hemp) extracted in oil form, and we investigated the accuracy of the labeling and thermal stability regarding the cannabinoids on 17 oil cannabis samples. In the UPLC chromatogram, we see a good resolution and there is no matrix effect and the accuracy were 98.2% to 102.6%, and the precision was 0.52%-8.18%. The linearity of the calibration curves in methanol was with a regression r2 ≥ 0.99. The lowest of detection (LOD) was 5-25 ng/mL, and the limit of quantification (LOQ) was 10-50 ng/mL. The study showed that only 30% of the commercial samples were within the acceptable range of +/-10% compared to the labeled ingredient concentrations. The thermal stability test profile showed a change in the concentration of cannabinoids in each sample at 37°C for one week, with an average loss of cannabinoids up to 15%. The validated method proved to be selective, accurate, and precise, with acceptable linearity within the calibration range with no matrix effect. The stability profile data indicated that high temperatures could change the quality of commercial samples.

Galli gigerii endothelium corneum (GGEC) is a traditional Chinese medicine commonly used in clinical practice to treat various conditions such as indigestion, vomiting, spermatorrhea, and enuresis. In this study, the volatile components of different concoctions of GGEC were examined by gas chromatography-ion mobility spectrometry (GC-IMS), and the changes of the components were compared by fingerprinting, combined with principal component analysis (PCA) and orthogonal partial least squares-discriminant analysis (OPLS-DA) to analyze the main volatile components and find out the different markers that can distinguish the different concoctions of GGEC. In the result, the GC-IMS fingerprints of GGEC and its different concoctions showed differences in their volatile components, of which 49 volatiles were clearly characterized, with some components including monomers and dimers. The characteristic volatile components of raw GGEC (SP) were n-nonanal, (E)-2-octenal, beta-ocimene, 2-ethyl-1-hexanol, etc. The characteristic volatile components of stir-fried GGEC (QC) are heptanal, 2-octanol, (E)-2-heptenal, etc. The characteristic volatile components of sand ironing GGEC (ST) are isoamyl acetate, decanal, cyclohexanone, 2-ethyl pyrazine, etc. The characteristic volatile components of stir-fried GGEC with vinegar (CZ) are thiazole, linalool, 2,3,5-trimethylpyrazine, etc. The characteristic volatile components of stir-fried GGEC with milk (FH) are 2-methylbutanoic acid, ethyl acetate, ethyl 2-hydroxypropanoate, butyl acetate, etc. By chemometric analysis, components such as n-nonanal, (E)-2-octenal, 2-pentyl-furan, butanal, 1,4-dioxane, and 2-methylpropanoic acid could be used as difference markers to distinguish different concoction products of GGEC. Furthermore, by analyzing different volatile compounds, we can examine the changes in volatile components during processing of GGEC, which can provide experimental data for the identification and establishment of quality standards.

Methyl 7,7'-dimethoxy-5'-(morpholinomethyl)-[4,4'-bibenzo[d][1,3] dioxole]-5-carboxylate methanesulfonate (IMM) is an innovative drug for the treatment of nonalcoholic fatty liver disease (NAFLD) owing to its high efficacy and low toxicity. In this study, five minor impurities (I, II, III, IV, and V) were identified and analyzed using spectroscopic evidence, chemical synthetic methods, and liquid chromatography-tandem mass spectrometry (LC-MS/MS). The impurities included hydrolysates and oxidation by-products extracted from both the drug in its final formulation and during synthesis. Toxicity prediction revealed potential carcinogenicity of impurity V containing an N-oxygen fragment. A reliable and selective HPLC method for the quantitative analysis of impurities I-IV and a sensitive HPLC-MS/MS method for potential genotoxic impurity V were developed and optimized. The methods were validated based on the International Council for Harmonization guidelines. Satisfactory linearity was obtained for the analytes over the range of 0.1-2.0 μg/mL for impurities I-IV and 0.3-30.0 ng/mL for impurity V, and in all cases, the fitting correlation coefficients exceeded 0.999. The obtained limits of detection values were 0.05 ng/mL and 0.005 μg/mL for impurity V and impurities I-IV, respectively. The precision and repeatability of the methods were less than 1.08% and 8.72% for each impurity. The recovery percentages of all impurities were in the range of 91.18%-111.27%, with the relative standard deviation of less than 3.69%. The greenness assessment of the HPLC method and the HPLC-MS/MS method were evaluated by using AGREE software with a score value of 0.72 and 0.68, respectively. The recommended procedures that were accurate, specific, and ecofriendly were applied to the existing active pharmaceutical ingredients of IMM, and they generated satisfactory results.

A simple and sensitive strategy using cyclodextrin-modified micellar electrokinetic chromatography with diode array detector was developed and applied for the simultaneous separation and determination of nine components in Sanyetangzhiqing (SYTZQ), a hypoglycemic and hypolipidemic agent. Several important parameters affecting separation performance were evaluated and optimized using single variable methods. Under the optimal conditions, baseline separation of the nine components, including four flavonoids (hyperoside, isoquercitrin, quercetin-3-O-glucuronoside, and astragalin), four phenolic acids (chlorogenic acid, rosmarinic acid, salvianolic acid B, and lithospermic acid), and a monoterpenoids (paeoniflorin), were achieved in less than 16 min. The correlation coefficients of the calibration curves were over 0.9996 for all the analytes. Intraday and interday precisions ranged from 0.4% to 4.8% and 1.7% to 5.0%, respectively. Recoveries of analytes varied from 95.3% to 105%. Validation results as well as the application to analyse SYTZQ samples demonstrated the applicability of the proposed method and thus provided an effective tool for the quality control of SYTZQ. Moreover, with the advantages of short time consuming, low energy consumption, high efficiency, and low cost, this method has laid a foundation for the determination and quality evaluation of multicomponents in Chinese herbal compounds.

TiO2 nanoparticles have emerged as a great photocatalyst to degrade organic contaminants in water; however, the nanoparticles dispersed in water could be difficult to be recovered and potentially become contaminant. Herbicide like 2,4-dichlorophenoxyacetic acid (2,4-D) used in agriculture usually ends up with a large fraction remaining in water and sediment, which may cause potential risk to human health and the ecosystem. This study proposes a greener method to utilize TiO2 as photocatalyst to remove 2,4-D from water. Accordingly, TiO2 nanoparticles (10-45 nm) were synthesized and grafted on lightweight fired clay to generate a TiO2-based floating photocatalyst. Experimental testing revealed that 60.2% of 2,4-D (0.1 mM) can be decomposed in 250 min under UV light with TiO2-grafted lightweight fired clay floating on water. Degradation fits well into the pseudo-first-order kinetic model. The floating photocatalysts can degrade approximately 50% 2,4-D in 250 min under sunlight and the degradation efficiency is stable for cycles. The results revealed that the fabrication of floating photocatalyst could be a promising and greener way to remove herbicide contaminants in water using TiO2.

Oprozomib, as a second-generation orally bioavailable protease inhibitor (PI), is undergoing clinical evaluation for the treatment of haematological malignancies. In relapsed refractory multiple myeloma (RRMM) patients, oprozomib has shown good efficacy as a single agent or combination therapy. In this experiment, our purpose was to validate a sensitive and rapid method for the determination of oprozomib concentration in rat plasma by ultraperformance liquid chromatography tandem mass spectrometry (UPLC-MS/MS). The samples were treated with acetonitrile as the precipitant and separated by gradient elution using a Waters Acquity UPLC BEH C18 column (2.1 mm × 50 mm, 1.7 μm). Using the selective reaction monitoring (SRM) method, the measurement was finished with the ion transitions of m/z 533.18 ⟶ 199.01 for oprozomib and m/z 493.03 ⟶ 112.03 for tepotinib (internal standard, IS), respectively. Meanwhile, acetonitrile and 0.1% formic acid aqueous solution were used as the mobile phase, and the flow rate was 0.3 mL/min. The lower limit of quantification (LLOQ) of the method was 1.0 ng/mL, and the linear relationship was good in the range of 1.0-100 ng/mL. In addition, the precision of four concentration levels was determined with the values of 3.1-7.3% and the accuracy was from -14.9% to 12.9%. Moreover, the recovery was determined to be from 85.1% to 96.1%, and the values of matrix effect were no more than 110.4%. The optimized UPLC-MS/MS method was also suitable for the pharmacokinetic study of rats after a single oral administration of 21 mg/kg oprozomib.