The effect of heat transfer on products of a thermally coupled shell and tube reactor consisting of two processes: Steam reforming of methane and oxidative coupling of methane

A direct method of converting natural gas into ethylene is the heterogeneously catalyzed oxidative coupling of methane (OCM), however, only with hydrocarbon yields limited to 30-35% despite enormous efforts to optimize the catalysts. By combining the exothermic OCM with a secondary process, namely steam reforming of methane (SRM), the methane conversion can be increased significantly while improving temperature control and simultaneously producing valuable synthesis gas. In this thesis, two different reactor concepts were developed to integrate the OCM and SRM reactions in an overall autothermal process, so that the OCM process is effectively cooled and the generated reaction energy is efficiently used to produce synthesis gas. The integration is most optimally achieved on the catalyst particle scale, which would eliminate the need for external heat exchange and opens up the possibility to use distributive oxygen dosing with which much higher product yields can be achieved. It is proposed to use a dual function catalyst particle in which the two chemical processes are physically separated by an inert, porous layer, such that additional diffusional resistances are intentionally created to control the reaction rates. This concept was studied with numerical simulations on the scale of a single catalyst particle and on reactor scale. It was found that the SRM and OCM reaction rates could be effectively tuned to achieve autothermal operation at the reactor scale, while the methane conversion was enhanced from 44% to 55%. An alternative integrated process can be achieved by combining OCM and SRM in a heat exchange reactor comprising of two separate reaction chambers which are thermally coupled. The OCM is carried out in packed bed reverse flow membrane reactor tubes submerged into a fluidized bed where the unconverted methane and byproducts from OCM are reformed, thus producing synthesis gas and consuming the reaction heat liberated by OCM. The feasibility of this concept is supported by experiments of OCM on a Mn/Na2WO4/SiO2 catalyst in a packed bed (porous Al2O3) membrane reactor. The results demonstrated that a C2 yield of 25-30 % can be achieved and that distributed feed of oxygen is optimal for the combined OCM/SRM reactor concept.

Conceptual Process Design and Economic Analysis of Oxidative Coupling of Methane

Performance and reaction mechanism of Mg-doped and Li-doped La2O3 catalysts in oxidative coupling of methane: DFT and experiment study

A new and very promising application of auto-thermal reactors is the coupling of endothermic and exothermic reactions where the product of the endothermic reaction is the desired one. Therefore, in this work, a reactor in which oxidative coupling of methane (OCM) and steam re-forming of methane (SRM) reactions take place simultaneously was modeled. The results were obtained in a wide range of different conditions such as inlet feed, inlet temperature, portions of OCM and SRM catalysts, and inlet velocity. In selection of the catalysts, more attention was drawn to prevent re-forming of OCM products. The main parameters of each reaction under different conditions such as conversion of the feed components, products selectivity and yield, temperature in the length of reactor, and component's concentration in the reactor were considered in course of this study. The results revealed that simultaneous OCM and SRM reactions in one reactor will tend to be auto-thermal, and the waste of energy will be reduced. The results also show that complete conversion of water and majority of methane and oxygen will decrease the amount of unwanted products at the reactor's discharge-a constraint that exists in single reactors of each reaction specially OCM.

Techno-economic analysis of integrating the methane oxidative coupling and methane reforming processes

For more than three decades, Oxidative Coupling of Methane (OCM) process has been comprehensively investigated as an attractive alternative for the commercially available ethylene production technologies such as ethane and naphtha cracking. Developing a suitable catalyst and proper reactor feeding policy, reviewing and deploying the efficient methods in the separation and purification of the undesired and desired products, possible energy saving and process intensification in different sections of the OCM process, each has been the subject of many researches in the past. In this paper, the interconnections of these aspects will be addressed by reviewing the performance of different alternative structures and unit operations in different sections of the OCM process. As a systematic approach in this analysis, a concurrent engineering approach supported by the experimental data which was extracted from an OCM miniplant scale facility was applied. Using an efficient porous packed bed membrane reactor and a proper set of operating conditions, up to 25% C2-yield, 20% C2H4-yield, and 52% C2H4-selectivity and the highest observed fluidized bed reactor C2-yield was achieved in this OCM miniplant. This experimental analysis was performed in the chair of process dynamics and operation at Berlin Institute of Technology under the main framework of Unifying Concepts in Catalysis (UniCat) project. The economic analysis of the industrial-scale operation showed promising potentials and also advantages of the final proposed OCM process-structure in this research.

Oxidative coupling of methane has been studied over (Mn+A+W)/SiO2 catalysts in a continuous–flow micro reactor, where A represents an alkali ion of Li, Na, K or Cs having different weight percents. The main aim of this study is to find the role of alkali ions in interaction between Mn and W species with SiO2 to make a proper structure for catalyzing oxidative coupling of methane (OCM) reaction. The catalysts were characterized by XRD, SEM, FTIR, TPR and also the electrical conductivity was measured in air and under OCM reaction. It was found that for the formation of crystallized catalyst, the amount of alkali ion should be such that the catalyst containing tungsten transforms into A2WO4. Using a smaller amount of alkali ions does not result in crystalline catalyst by calcination under the same condition of temperature and atmosphere. However, under the OCM reaction condition the catalyst gradually turns into a crystalline structure and its catalytic performance, i.e. conversion and selectivity, for the OCM reaction is almost similar to the (Mn+A2WO4)/SiO2 catalyst. The transformation of the catalyst containing alkali ions from amorphous to crystalline one indicates a kind of structural flexibility of the catalyst under OCM atmosphere. The structural flexibility of the catalyst under the OCM reaction is considered to be the main chemical role of the alkali ions.

Techno-economic analysis of oxidative coupling of methane: Current state of the art and future perspectives

An oxidative coupling of methane (OCM) is a promising process to convert methane into ethylene and ethane; however, it suffers from the relatively low selectivity and yield of ethylene at high methane conversion. In this study, a membrane reactor is applied to the OCM process in order to prevent the deep oxidation of a desirable ethylene product. The mathematical model of OCM process based on mass and energy balances coupled with detailed OCM kinetic model is employed to examine the performance of OCM membrane reactor in terms of CH4 conversion, C2 selectivity, and C2 yield. The influences of key operating parameters (i.e., temperature, methane-to-oxygen feed ratio, and methane flow rate) on the OCM reactor performance are further analyzed. The simulation results indicate that the OCM membrane reactor operated at higher operating temperature and lower methane-to-oxygen feed ratio can improve C2 production. An optimization of the OCM membrane reactor using a surface response methodology is proposed in this work to determine its optimal operating conditions. The central composite design is used to study the interaction of process variables (i.e., temperature, methane-to-oxygen feed ratio, and methane flow rate) and to find the optimum process operation to maximize the C2 products yield.

Molecular structure and catalytic promotional effect of Mn on supported Na2WO4/SiO2 catalysts for oxidative coupling of methane (OCM) reaction

Mini-channel heat exchangers for industrial distillation processes

Performance analysis of shell and tube heat exchanger: Parametric study

The commercialization of the oxidative coupling of methane (OCM) process is hindered by its low C 2 hydrocarbon yield and C 2 H 4 /C 2 H 6 product ratio. In this work, a dual‐bed catalytic system comprising a SrCl 2 additive layer packed above the classic Na 2 WO 4 ‐MnO x /SiO 2 catalyst has been proposed. The promoting effect of the introduced SrCl 2 additives is revealed. On one hand, SrCl 2 undergoes in situ oxidative dehalogenation to generate chloromethane active intermediates, which trigger chlorine radical chain transfer reactions in the OCM catalyst layer, significantly reducing the energy barriers of methane activation and ethane dehydrogenation. On the other hand, SrCl 2 , with a high melting point, prevents the metal chlorides from evaporating and covering the catalyst active sites, but still releases abundant chloromethane intermediates to participate in the OCM reaction at a moderate rate. Consequently, a more reactive and stable OCM reaction was achieved, with a C 2 yield up to 25% and a C 2 H 4 /C 2 H 6 ratio around 5 in 20 h of continuous operation. This work provides an efficient strategy for a highly active and stable OCM process.

This research studied the design and development of ethylene carbonate production process from biomass. The overall process consisted of four sections including biogas production and treatment; oxidative coupling of methane (OCM) process; ethylene oxide (EO) process and ethylene carbonate (EC) process. Biogas was produced by a novel anaerobic digestion process and then treated to remove carbon dioxide. OCM reaction on Na-W-Mn/SiO2 catalyst was employed to produce ethane and ethylene (C2) products. Ethylene was then converted to ethylene oxide and ethylene carbonate by utilizing carbon dioxide generated from other parts of the process. Process simulation was performed by Aspen Plus® program. Novel kinetic model of OCM and EO had been employed in the developed process. Four key parameters of the process i.e. oxygen feed flow rate for OCM process, OCM reaction temperature, oxygen feed flow rate for EO process and EO reaction temperature were studied. The optimized process converts 99.98% of methane in biogas and yields 27.47% of ethylene, which consecutively converts into ethylene carbonate by utilizing 27.54% of carbon dioxide generated from the process. Process heat integration was performed in the optimized model. The heat-integrated process required 465 kW of energy consumption, which is about 70% reduction from the base case model. This process provides a green chemical concept, which uses biomass as raw materials and utilizes carbon dioxide generated to produce a higher valuable chemical.

In the second part of this paper (Part II), the potentials and characteristics of an industrial-scale Oxidative Coupling of Methane (OCM) process integrated with CO2-hydrogenation, ethane dehydrogenation, and methane reforming processes are highlighted. This novel process concept comprises a direct conversion of methane to ethane and ethylene and further conversion of the resulted carbon dioxide and remaining unreacted methane, respectively, to methanol and syngas. In this context, the selected experimental results of the catalytic CO2-hydrogenation to methanol reported in the first part of this paper (Part I), were utilized to represent its industrial-scale performance. The experimental results of the mini plant-scale operation of an OCM reactor and CO2 removal units along with the experimental and industrial data available for representing the operation and performance of all process-units in the integrated process structures were utilized to perform a comparative techno-economic environmental analysis using Aspen-Plus simulation and an Aspen Economic Process Analyzer. The experimental procedure and the results of testing the sequence of OCM and CO2-hydrogenation reactors are particularly discussed in this context. It was observed that in the sequential operation of these reactors, ethylene will be also hydrogenated to ethane over the investigated catalysts. Therefore, the parallel-operation of these reactors was found to be a promising alternative in such an integrated process. The main assumptions and the conceptual conclusions made in this analysis are reviewed and discussed in this paper in the light of the practical limitations encountered in the experimentations. In the context of a multi-scale analysis, the contributions of the design and operating parameters in the scale of catalyst and reactor as well as in the process-scale represented by analyzing the type and operating conditions of the downstream-units and the process-flowsheets on the economic and environmental performance of the integrated process structures were studied. Moreover, the economic impacts of extra ethylene and methanol produced respectively via the integrated ethane dehydrogenation and CO2-hydrogenation sections were analyzed in detail. The required capital investment was found to be even smaller than the yearly operating cost of the plant. The environmental impacts and sustainability of the integrated OCM process were found to be enhanced by securing a minimum direct CO2-emission and energy-efficient conversion of CO2 and the unreacted CH4, respectively, to methanol and syngas. Besides producing such value-added by-products, efficient operation of downstream process-units was secured by minimizing the energy usage and ethylene losses. Under the considered conditions in this analysis, the specifications of the finally selected integrated OCM process structure, providing the fastest return of investments (less than 8 years), are highlighted.