Life cycle greenhouse gas emissions of electricity generated from waste coal in the United States

Aluminum production is a major energy consumer and important source of greenhouse gas (GHG) emissions globally. Estimation of the energy consumption and GHG emissions caused by aluminum production in China has attracted widespread attention because China produces more than half of the global aluminum. This paper conducted life cycle (LC) energy consumption and GHG emissions analysis of primary and recycled aluminum in China for the year 2020, considering the provincial differences on both the scale of self-generated electricity consumed in primary aluminum production and the generation source of grid electricity. Potentials for energy saving and GHG emissions reductions were also investigated. The results indicate that there are 157,207 MJ of primary fossil energy (PE) consumption and 15,947 kg CO2-eq of GHG emissions per ton of primary aluminum ingot production in China, with the LC GHG emissions as high as 1.5–3.5 times that of developed economies. The LC PE consumption and GHG emissions of recycled aluminum are very low, only 7.5% and 5.3% that of primary aluminum, respectively. Provincial-level results indicate that the LC PE and GHG emissions intensities of primary aluminum in the main production areas are generally higher while those of recycled aluminum are lower in the main production areas. LC PE consumption and GHG emissions can be significantly reduced by decreasing electricity consumption, self-generated electricity management, low-carbon grid electricity development, and industrial relocation. Based on this study, policy suggestions for China’s aluminum industry are proposed. Recycled aluminum industry development, restriction of self-generated electricity, low-carbon electricity utilization, and industrial relocation should be promoted as they are highly helpful for reducing the LC PE consumption and GHG emissions of the aluminum industry. In addition, it is recommended that the central government considers the differences among provinces when designing and implementing policies.

We reported previously on the Biogasdoneright™ system for on‐farm biogas production. This innovative system employs sequential (year‐round) cropping to produce both food and energy from agricultural biomass, primarily cellulosic materials. This paper uses a marginal analysis approach to estimate the life cycle greenhouse gas emissions (GHGs) of electricity and biomethane produced by four currently operating Italian biogas plants that process various agricultural feedstocks, residues, and by‐products. The biogas is burned on‐farm to generate electricity that is then exported to the grid. The marginal lifecycle GHGs of this farm‐produced electricity range from ‐335 to 25 grams CO2 per kilowatt hour (kWh). By comparison, the marginal GHGs of electricity generated by fossil fuels in the European Union (EU) is 752 grams CO2 per kWh. The biogas might also be upgraded to produce pipeline‐quality biomethane, a direct substitute for natural gas. The marginal lifecycle GHGs of biomethane potentially produced from the Biogasdoneright™ plants range from 10 to ‐36 grams CO2 per megajoule (MJ) while the corresponding figure for a conventional biogas plant is 27 grams CO2 per MJ. Natural gas in the EU produces 72 grams CO2 per MJ and marginal fossil fuel in the EU generates 115 grams CO2 per MJ. Negative GHG emissions arise largely from avoided emissions of agricultural effluents and residues. © 2017 Society of Chemical Industry and John Wiley & Sons, Ltd

Introducing demand to supply ratio as a new metric for understanding life cycle greenhouse gas (GHG) emissions from rainwater harvesting systems

The decarbonization of regional electricity systems is a critical enabler of broader economy-wide decarbonization strategies and has motivated robust research on how to decarbonize electricity systems at minimum monetary cost. Since these efforts often focus on the operation of electricity systems, however, they do not account for emissions of the full life cycle associated with different resources. Different resource mixes can achieve a similar level of apparent decarbonization through operational emissions, while achieving very different levels of life cycle greenhouse gas (GHG) emissions reductions. To explore these differences, we model the expansion of the California electricity system from 2030 to 2045 using a simplified electricity dispatch model to investigate how the planning of future electricity systems may differ between prioritizing minimum cost versus minimum life cycle GHG emissions under a common target for operational GHG reductions. We find that explicitly planning for minimum life cycle GHG emissions yields an additional 1.6%–2.0% reduction in annual life cycle GHG emissions at a cost penalty of 5.1%–6.9% and that electricity resource mixes that minimize life cycle GHG emissions tend to favor high capacity factor zero-carbon resources and long-duration storage compared to a minimum cost approach. Comparatively, we find that aggressive supply chain decarbonization of generation and storage technologies reduces life cycle GHG emissions of electricity supplies by 3.0% to 14% and combining both increases these reductions to 5.0% to 16%. Further, we find that applying a carbon tax to minimum cost-based capacity expansion can incentivize planning to account for life cycle GHG emissions. Our results indicate that a planning approach focused on minimizing life cycle GHG emissions may not be palatable, but significant reductions in life cycle emissions can be realized through conventional mechanisms like carbon taxes, import standards, and targeted supply chain decarbonization.

The decarbonization of regional electricity systems is a critical enabler of broader economy-wide decarbonization strategies and has motivated robust research on how to decarbonize electricity systems at minimum monetary cost. Since these efforts often focus on the operation of electricity systems, however, they do not account for emissions of the full life cycle associated with different resources. Different resource mixes can achieve a similar level of decarbonization apparent decarbonization through operational emissions, while achieving very different levels of life cycle greenhouse gas (GHG) emissions reductions. To explore these differences, we model the expansion of the California electricity system from 2030 to 2045 using a simplified electricity dispatch model to investigate how the planning of future electricity systems may differ between prioritizing minimum cost versus minimum life cycle GHG emissions under a common target for operational GHG reductions. We find that explicitly planning for minimum life cycle GHG emissions yields an additional 1.6-2.0% reduction in annual life cycle GHG emissions at a cost penalty of 3.2–9.6% and that electricity resource mixes that minimize life cycle GHG emissions tend to favor high capacity factor zero-carbon resources and long-duration storage compared to a minimum cost approach. Comparatively, we find that aggressive supply chain decarbonization of generation and storage technologies reduces life cycle GHG emissions of electricity supplies by 3.0% to 14% and combining both increases these reductions to 5.0% to 16%. Further, we find that applying a carbon tax to minimum cost-based capacity expansion can incentivize planning to account for life cycle GHG emissions. Our results indicate that a planning approach focused on minimizing life cycle GHG emissions may not be palatable, but significant reductions in life cycle emissions can be realized through conventional mechanisms like carbon taxes, import standards, and targeted supply chain decarbonization.

Impacts of alternative fuel combustion in cement manufacturing: Life cycle greenhouse gas, biogenic carbon, and criteria air contaminant emissions

We suggest a 2D-plot representation combined with life cycle greenhouse gas (GHG) emissions and life cycle cost for various energy conversion technologies. In general, life cycle assessment (LCA) not only analyzes at the use phase of a specific technology, but also covers widely related processes of before and after its use. We use life cycle GHG emissions and life cycle cost (LCC) to compare the energy conversion process for eight resources such as coal, natural gas, nuclear power, hydro power, geothermal power, wind power, solar thermal power, and solar photovoltaic (PV) power based on the reported LCA and LCC data. Among the eight sources, solar PV and nuclear power exhibit the highest and the lowest LCCs, respectively. On the other hand, coal and wind power locate the highest and the lowest life cycle GHG emissions. In addition, we used the 2D plot to show the life cycle performance of GHG emissions and LCCs simultaneously and realized a correlation that life cycle GHG emission is largely inversely proportional to the corresponding LCCs. It means that an expensive energy source with high LCC tends to have low life cycle GHG emissions, or is environmental friendly. For future study, we will measure the technological maturity of the energy sources to determine the direction of the specific technology development based on the 2D plot of LCCs versus life cycle GHG emissions.

A probabilistic fleet analysis for energy consumption, life cycle cost and greenhouse gas emissions modelling of bus technologies

Plug-in hybrid electric vehicle (PHEV) technology has the potential to reduce operating cost, greenhouse gas (GHG) emissions, and petroleum consumption in the transportation sector. However, the net effects of PHEVs depend critically on vehicle design, battery technology, and charging frequency. To examine these implications, we develop an optimization model integrating vehicle physics simulation, battery degradation data, and U.S. driving data. The model identifies optimal vehicle designs and allocation of vehicles to drivers for minimum net life cycle cost, GHG emissions, and petroleum consumption under a range of scenarios. We compare conventional and hybrid electric vehicles (HEVs) to PHEVs with equivalent size and performance (similar to a Toyota Prius) under urban driving conditions. We find that while PHEVs with large battery packs minimize petroleum consumption, a mix of PHEVs with packs sized for ∼25–50 miles of electric travel under the average U.S. grid mix (or ∼35–60 miles under decarbonized grid scenarios) produces the greatest reduction in life cycle GHG emissions. Life cycle cost and GHG emissions are minimized using high battery swing and replacing batteries as needed, rather than designing underutilized capacity into the vehicle with corresponding production, weight, and cost implications. At 2008 average U.S. energy prices, Li-ion battery pack costs must fall below $590/kW h at a 5% discount rate or below $410/kW h at a 10% rate for PHEVs to be cost competitive with HEVs. Carbon allowance prices offer little leverage for improving cost competitiveness of PHEVs. PHEV life cycle costs must fall to within a few percent of HEVs in order to offer a cost-effective approach to GHG reduction.

Despite the ever-growing body of life cycle assessment (LCA) literature on electricity generation technologies, inconsistent methods and assumptions hamper comparison across studies and pooling of published results. Synthesis of the body of previous research is necessary to generate robust results to assess and compare environmental performance of different energy technologies for the benefit of policy makers, managers, investors, and citizens. With funding from the U.S. Department of Energy, the National Renewable Energy Laboratory initiated the LCA Harmonization Project in an effort to rigorously leverage the numerous individual studies to develop collective insights. The goals of this project were to: (1) understand the range of published results of LCAs of electricity generation technologies, (2) reduce the variability in published results that stem from inconsistent methods and assumptions, and (3) clarify the central tendency of published estimates to make the collective results of LCAs available to decision makers in the near term. The LCA Harmonization Project's initial focus was evaluating life cycle greenhouse gas (GHG) emissions from electricity generation technologies. Six articles from this first phase of the project are presented in a special supplemental issue of the Journal of Industrial Ecology on Meta-Analysis of LCA: coal (Whitaker et al. 2012), concentratingmore » solar power (Burkhardt et al. 2012), crystalline silicon photovoltaics (PVs) (Hsu et al. 2012), thin-film PVs (Kim et al. 2012), nuclear (Warner and Heath 2012), and wind (Dolan and Heath 2012). Harmonization is a meta-analytical approach that addresses inconsistency in methods and assumptions of previously published life cycle impact estimates. It has been applied in a rigorous manner to estimates of life cycle GHG emissions from many categories of electricity generation technologies in articles that appear in this special supplemental supplemental issue, reducing the variability and clarifying the central tendency of those estimates in ways useful for decision makers and analysts. Each article took a slightly different approach, demonstrating the flexibility of the harmonization approach. Each article also discusses limitations of the current research, and the state of knowledge and of harmonization, pointing toward a path of extending and improving the meta-analysis of LCAs.« less

We integrate life cycle indicators for various technologies of an energy system model with high spatiotemporal detail and a focus on Europe and North Africa. Using multi-objective optimization, we calculate a pareto front that allows us to assess the trade-offs between system costs and life cycle greenhouse gas (GHG) emissions of future power systems. Furthermore, we perform environmental ex-post assessments of selected solutions using a broad set of life cycle impact categories. In a system with the least life cycle GHG emissions, the costs would increase by ~63%, thereby reducing life cycle GHG emissions by ~82% compared to the cost-optimal solution. Power systems mitigating a substantial part of life cycle GHG emissions with small increases in system costs show a trend towards a deployment of wind onshore, electricity grid and a decline in photovoltaic plants and Li-ion storage. Further reductions are achieved by the deployment of concentrated solar power, wind offshore and nuclear power but lead to considerably higher costs compared to the cost-optimal solution. Power systems that mitigate life cycle GHG emissions also perform better for most impact categories but have higher ionizing radiation, water use and increased fossil fuel demand driven by nuclear power. This study shows that it is crucial to consider upstream GHG emissions in future assessments, as they represent an inheritable part of total emissions in ambitious energy scenarios that, so far, mainly aim to reduce direct CO2 emissions.

The photovoltaics (PV) industry is growing rapidly to meet the increasing demand of green power. As the industry grows, the manufacturing processes and the material and energy efficiencies of PV cells and panels are improving. To assess the impacts of this trend, future scenarios of single-crystalline (single-Si, also known as mono-crystalline) silicon and cadmium-telluride (CdTe) PV systems installed on European residences were established. Assessment of the improvement potential of PV electricity-generating technologies such as single-Si and CdTe could be considered in long-term energy strategy decisions. This study aims to provide scenario-based information about the environmental per-formance of single-Si and CdTe PV modules produced and operated in the far future (2030 to 2050). The deployment application assessed considers European residential roofs. We made scenario-dependent projections of key parameters for single-Si and CdTe PV panels manufactured in 2050. The parameters included cell efficiency, module efficiency, wafer thickness, cutting losses, kerf losses, silver use, glass thickness and operational lifetime. This study combines developments for these parameters with projections of the environmental performance of electricity mixes in the main manufacturing countries/regions (European Union, China and the United States of America) and with projections of the environ-mental performance of basic material production (aluminium, copper, magnesium, nickel, pig iron, zinc, clinker and flat glass) in the far future. The three scenarios used in the assessment of future PV electricity were categorized into three classes: 'business as usual' (BAU), 'realistic improvement' (REAL) and 'optimistic improvement' (OPT). It estimates the current life cycle greenhouse gas emissions of single-Si PV electricity produced on the roofs of European residences to be approximately 80 grams CO2-equi-valent per kWh (g CO2-eq per kWh). Based on the projected changes to key parameters and the background system, life cycle greenhouse gas (GHG) emissions could be reduced to 65% (scenario BAU), 31% (scenario REAL) and 18% (scenario OPT) of that value in the far future. Results for other life cycle assessment (LCA) metrics are also assessed in this study such as: non-renewable cumulative energy demand, acidification potential, human toxicity potential, photochemical ozone creation potential, particulate matter formation potential, and land use. We calculated the total energy payback time (EPBT) and the non-renewable energy payback time (NREPBT) in the far future of single-crystalline silicon-based PV panels operated in Europe by dividing the estimate of non-renewable cumulative energy demand of PV electricity for the given scenario by the non-renewable cumulative energy demand of the scenario-dependent national and regional non-renewable residual electricity mixes. The study estimates the payback time could be reduced from 2.4 years today to 1.7, 1.2 and 1.2 years (scenarios BAU, REAL and OPT, respectively) in the far future, based on the assumptions and projections in the analysis. It finally estimates the current life cycle greenhouse gas emissions of CdTe PV electricity produced on the roofs of European residences to be approximately 30 g CO2-eq per kWh. Based on the projected changes to key parameters and the background system, life cycle GHG emissions could be reduced to 70% (scenario BAU), 44% (scenario REAL) and 32% (scenario OPT) of that value in the far future.

This study evaluated the life cycle greenhouse gas (GHG) emissions from different hydroelectricity generation systems by first performing a comprehensive review of the hydroelectricity generation system life cycle assessment (LCA) studies and then subsequent computation of statistical metrics to quantify the life cycle GHG emissions (expressed in grams of carbon dioxide equivalent per kilowatt hour, gCO2e/kWh). A categorization index (with unique category codes, formatted as “facility type-electric power generation capacity”) was developed and used in this study to evaluate the life cycle GHG emissions from the reviewed hydroelectricity generation systems. The unique category codes were labeled by integrating the names of the two hydro power sub-classifications, i.e., the facility type (impoundment (I), diversion (D), pumped storage (PS), miscellaneous hydropower works (MHPW)) and the electric power generation capacity (micro (µ), small (S), large (L)). The characterized hydroelectricity generation systems were statistically evaluated to determine the reduction in corresponding life cycle GHG emissions. A total of eight unique categorization codes (I-S, I-L, D-µ, D-S, D-L, PS-L, MHPW-µ, MHPW-S) were designated to the 19 hydroelectricity generation LCA studies (representing 178 hydropower cases) using the proposed categorization index. The mean life cycle GHG emissions resulting from the use of I-S (N = 24), I-L (N = 8), D-µ (N = 3), D-S (N = 133), D-L (N = 3), PS-L (N = 3), MHPW-µ (N = 3), and MHPW-S (N = 1) hydroelectricity generation systems are 21.05 gCO2e/kWh, 40.63 gCO2e/kWh, 47.82 gCO2e/kWh, 27.18 gCO2e/kWh, 3.45 gCO2e/kWh, 256.63 gCO2e/kWh, 19.73 gCO2e/kWh, and 2.78 gCO2e/kWh, respectively. D-L hydroelectricity generation systems produced the minimum life cycle GHGs (considering the hydroelectricity generation system categories with a representation of at least two cases).

Life cycle assessment of primary energy demand and greenhouse gas (GHG) emissions of four propylene production pathways in China

Plug-in hybrid electric vehicle (PHEV) technology has the potential to help address economic, environmental, and national security concerns in the United States by reducing operating cost, greenhouse gas (GHG) emissions and petroleum consumption from the transportation sector. However, the net effects of PHEVs depend critically on vehicle design, battery technology, and charging frequency. To examine these implications, we develop an integrated optimization model utilizing vehicle physics simulation, battery degradation data, and U.S. driving data to determine optimal vehicle design and allocation of vehicles to drivers for minimum life cycle cost, GHG emissions, and petroleum consumption. We find that, while PHEVs with large battery capacity minimize petroleum consumption, a mix of PHEVs sized for 25–40 miles of electric travel produces the greatest reduction in lifecycle GHG emissions. At today’s average US energy prices, battery pack cost must fall below $460/kWh (below $300/kWh for a 10% discount rate) for PHEVs to be cost competitive with ordinary hybrid electric vehicles (HEVs). Carbon allowance prices have marginal impact on optimal design or allocation of PHEVs even at $100/tonne. We find that the maximum battery swing should be utilized to achieve minimum life cycle cost, GHGs, and petroleum consumption. Increased swing enables greater all-electric range (AER) to be achieved with smaller battery packs, improving cost competitiveness of PHEVs. Hence, existing policies that subsidize battery cost for PHEVs would likely be better tied to AER, rather than total battery capacity.