Carbon dioxide, ethylene and water vapor sorption in poly(lactic acid)

This work investigates the effect of the addition of a well‐known antioxidant, α‐tocopherol in poly (lactic acid) flexural and barrier properties. For that purpose, films of poly(lactic acid) enriched with 0, 2.2, and 4.4% of α‐tocopherol were prepared. Differential scanning calorimetry, thermogravimetric analysis, and dynamic mechanical analysis were used to characterize the changes in the mechanical and thermal properties. The sorption of oxygen and carbon dioxide in the prepared enriched films of poly(lactic acid) was measured at different temperatures between 283 and 313 K and pressures up to atmospheric pressure using a Quartz Crystal Microbalance. Although no significant changes were found in the mechanical and thermal properties, the addition of α‐tocopherol promotes an increasing in the oxygen sorption and the convex shape of the isotherms indicate a strong interaction gas‐polymer. Regarding the sorption of carbon dioxide, no pronounced effect was found. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011

Gas sorption in poly(lactic acid) and packaging materials

The sorption of carbon dioxide in glassy Poly(lactic acid) (PLA) films was studied by quartz crystal microbalance (QCM) at high pressures. Two thermal treatments, melted and quenched, were performed in PLA with two different L:D contents, 80:20 and 98:2, films and compared with a third thermal protocol, annealed, and used in a previous work. The results obtained show that for pressures higher than 2 MPa, the carbon dioxide solubility is larger in PLA 80:20 than in PLA 98:2, indicating that the L:D plays a dominant role on this property. The thermal treatments only affect the gas solubility in PLA 98:2. Sorption isotherms at temperatures 303, 313, and 323 K, below the glass transition temperature of the polymer, and pressures up to 5 MPa were measured and analyzed with three different models, the dual‐mode sorption model, the Flory–Huggins equation, and a modified dual‐mode sorption model where the Henry's law term was substituted by the Flory–Huggins equation. This last model performs especially well for CO2 in PLA 80:20, due to the convex upward curvature of the solubility isotherms for that system. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 616–625, 2007

The sorption of carbon dioxide in poly(lactic acid) (PLA) was studied by quartz crystal microbalance at high pressures. To address the effect of the D isomer present in the polymer on the gas sorption, measurements were performed in PLA with two different L:D contents, 80:20 and 98:2. New data for the solubility of carbon dioxide in PLA 80:20 and PLA 98:2 over a temperature range from 303.2 to 323.2 K and up to 5 MPa are presented. The results obtained were correlated with the dual‐mode sorption model and the Flory‐Huggins equation. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 1010–1019, 2006

The sorption and diffusion of water vapor in poly(ethylene terephthalate) (PET) film were measured by applying a thermogravimetric analyzer (TG-DTA), which customarily has been used to detect the weight loss of a sample with the increase of temperature under a given atmosphere. In this case, we detected the weight gain of PET film by sorption of water vapor under a given humidity at a constant temperature. Sorption-rate curves were successfully obtained in spite of the low solubility of PET film and the presence of Fickian-type curves. The solubility was better described according to the dual-mode sorption model. The diffusion coefficients were determined in their initial slopes by the short-time method. We found that the diffusion coefficient depended on vapor pressure.

Microwave-Powered Thermal Regeneration of Sorbents for CO2, Water Vapor and Trace Organic Contaminants

We report the synthesis of two isoreticular, mixed-ligand metal-organic frameworks (MOFs), [Cd(μ2-mia)(μ2-bpe)]n·n(DMF)0.5·n(H2O)0.5 (1) and [Cd(μ2-nia)(μ2-bpee)]n·nDMF (2), where mia = 5-methoxyisophthalate, nia = 5-nitroisophthalate, bpe = 1,2-bis(4-pyridyl)ethane, bpee = 1,2-bis(4-pyridyl)ethylene, and DMF = N,N'-dimethylformamide. Variable-temperature powder X-ray diffraction studies confirmed that both MOFs remain crystalline with activation at high temperatures. Variable-temperature single-crystal X-ray diffraction studies were performed on 1, 2, and a previously published, isoreticular structure, [Cd(μ2-nia)(μ2-bpe)1.5]n·nDMF0.84 (3). These studies show that upon desolvation that monocrystallinity is retained to significantly higher temperatures for 2 and 3 when compared to 1 for which only a partially desolvated crystal structure could be obtained. Carbon dioxide sorption is negligible for 1 at 195 and 298 K, while it is higher for 2 than 3 at 298 K and reversed at 195 K. Water vapor sorption increases in the order 1, 2, and 3. On the contrary, water liquid sorption was significantly higher for 1 when compared to 2. The variable-temperature structures of the (partially) desolvated forms of 1, 2, and 3 give some insight into the reasons for the remarkably different gas, vapor, and liquid sorption properties.

Mixed gas sorption in elastic solids

The sorption of methane, ethane, ethylene, and carbon dioxide in ALPO-5 and SAPO-5 (temperature 305−353 K, and pressure 0−200 kPa) and the thermodynamics of sorption have been investigated under similar conditions using a gravimetric sorption apparatus. The Dubinin−Polanyi equation is found to fit the sorption of all the sorbates in both the sorbents except for carbon dioxide in ALPO-5. The Freundlich model fits the equilibrium data on the sorption of carbon dioxide in ALPO-5. The two sorbents differ widely in the isosteric heat of sorption and also in its variation with surface coverage of these sorbates. Entropy changes on the sorption have also been analyzed. The sorption of these gases in both the sorbents is found to be supermobile, the mobility being much higher in ALPO-5 than in SAPO-5.

In this contribution the sorption of water vapor in Poly(L-lactic acid) (PLLA) was studied by time-resolved FTIR spectroscopy. The collected FTIR data were analyzed by complementary approaches such as difference spectroscopy, two-dimensional correlation spectroscopy (2D-COS), and least-squares curve-fitting analysis which provided information about the overall diffusivity, the nature of the molecular interactions among the polymer and the penetrant and the dynamics of the various molecular species. The diffusion coefficient were evaluated as a function of vapor activity and were found in good agreement with previously reported values. The system showed a Fickian behavior with diffusivity increasing with penetrant concentration. Two distinct water species (first-shell and second-shell layers) were detected and quantified by coupling FTIR and gravimetric measurements.

Direct Measurement of the Heat of Carbon Dioxide Sorption in Polymeric Materials

Modeling of carbon dioxide and water sorption in glassy polymers through PC-SAFT and NET PC-SAFT

Biodegradable boron-containing poly(lactic acid) for fertilizers with prolonged action

ABSTRACTSurface modification of poly(lactic acid) (PLA) film is performed via 172 nm excimer lamp irradiation. Effects on water vapor solubility and physical properties via vacuum ultraviolet (VUV) irradiation are studied systematically. After VUV irradiation, water vapor solubility increases approximately 11–43% in the low‐pressure region and approximately 20–38% in the high‐pressure region as surface hydrophilicity increased. The increase is attributed to hydrogen bonding with the carboxyl groups because of VUV radiation. The modified layer is significantly swelling after water vapor sorption. The hydrophilic layer forms a thickness of 2–3 μm from the irradiated surface via VUV radiation, but no changes are observed inside the irradiated film. Therefore, PLA film solubility after irradiation is enhanced by hydrophilicity and the swelling effect of the surface. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015, 132, 42200.

Results are summarized for an investigation of the sorption rates of gases on vapor-deposited titanium films. The usefulness of such films for ultrahigh speed vacuum pumping is appraised. The sorption of hydrogen, deuterium, oxygen, nitrogen, carbon monoxide, carbon dioxide, water vapor, helium, argon, and methane onto titanium films was measured for a variety of circumstances using techniques and apparatus developed for this specific purpose. The information obtained and techniques evolved in this study have shown that large-scale getter pumping is feasible and can be a very effective means of pumping many gases. Sticking fractions larger than 0.8 were obtained for hydrogen, deuterium, oxygen, nitrogen, carbon monoxide, and carbon dioxide. The experiments have shown that the sticking fraction for gases on vapor-deposited films is a function of the deposition conditions. There is strong evidence to support the supposition that conditions which favor the formation of a porous, fine-grained film structure with a large surface-to-volume ratio produce films with the highest sorption rates. The technique for measuring sticking fractions is new and in many respects unique. It utilizes a very large sorption surface, thus minimizing the perturbing effect of the instrumentation and evaporation apparatus and reducing the hazard of film contamination due to small leaks in the system or outgassing of system components. The method gives especially good accuracy for measurements of sticking fractions approaching unity. The quantity of gas adsorbed, the gas flux onto the getter surface, and the gas flux leaving the getter surface are measured directly. Any two of these three independent measurements can be used to determine the sticking fraction, thereby providing a means of checking the data. The evaporation techniques, substrate surface, and substrate area were chosen to very nearly duplicate the conditions likely to be encountered in the practical application of large-scale getter pumping. (auth)