Abstract
The use of the tank as well as a container or tank of liquid reserves to make use of the tank as a necessity. By using its own tank design model which is technically very possible to make the pressure in the tank is less than atmospheric pressure so that the tank will take some role pump connected in series are used for the purpose of improving high pressure. Thus the pressure in the tank is smaller than the atmospheric pressure is only generated from the process flow itself will save pump power required on the press. To prevent the air pressure in the tank exceeds the atmospheric pressure relief valve on the tank supplied air to the atmosphere. The more water into the tank, the greater the downward thrust force due to the weight of water and by the buoy to the piston in fixed position, the tank will move downward relative to the piston. The pressure in the tank due to the movement of the closed tube will follow the phenomenon of negative pressure. To get a larger volume of air or spring difleksi rate greater then the pole float should be as light as possible and frictional forces as small as possible. The goal is to produce a prototype tank that can lighten the pump working in particular on the discharge side so it can be input pump power savings. The calculations show that a high hit on the side of the press can be reduced upto 100 percent even including reducing losses on the discharge side by enlarging the capacity of the tank. Thus happen electricity savings of the power required on the discharge side of the pump to drain the water into the tank. With spring replacement inverting the inversion moment will produce a higher pressure suction force behind the rise of the spring.
Highlights
Proses pengisian tangki penampung atau tangki cadangan dari pompa yang diterapkan selama ini adalah dengan mengupayakan agar tekanan yang ada dalam tangki sama dengan tekanan atmosfir, agar tidak ada tambahan tekanan yang terjadi
By using its own tank design model which is technically very possible to make the pressure in the tank is less than atmospheric pressure so that the tank will take some role pump connected in series are used for the purpose of improving high pressure
The pressure in the tank is smaller than the atmospheric pressure is only generated from the process flow itself will save pump power required on the press
Summary
Proses pengisian tangki penampung atau tangki cadangan dari pompa yang diterapkan selama ini adalah dengan mengupayakan agar tekanan yang ada dalam tangki sama dengan tekanan atmosfir, agar tidak ada tambahan tekanan yang terjadi. Usulan tulisan ini pengembangan dari usulan sebelmnya adalah untuk menguji model terhadap efektifitas kerja sistem yang terdiri dari pelampung, torak dan pegas pembalik digantikan oleh efek momen lengan. Agar diperoleh batas gaya dorong keatas maksimum oleh pelampung, maka berat air yang dipindahkan akan sama dengan gaya dorong pelampung terhadap torak dimana isi air pada tangki harus lebih besar dari volume pelampung itu sendiri. Untuk itu yang harus diketahui adalah berapa besar rata-rata tekanan negatif yang diperoleh dari gaya guna yang dihasilkan oleh berat air dan pelampung untuk meringankan kerja pompa. Tujuan Tulisan ini bertujuan untuk menghasilkan tangki protipe yang mampu meringankan kerja pompa khususnya meningkatkan head tekan pompa (pada sisi discharge) sehingga dapat dilakukan penghematan daya input pompa hingga sebesar daya yang diperlukan pada sisi dischargenya disesuaikan dengan dimensi tinggi tangki dan pelampung. Hukum Boyle [2] Tekanan dan Volume dari suatu gas adalah berbanding terbalik pada masa gas dan suhu yang konstan (isotermis), yang berarti bahwa tekanan naik, volume turun dan sebaliknya volume naik dan tekanan turun
Sign-in/Register to view highlights & summary Talk to us
Join us for a 30 min session where you can share your feedback and ask us any queries you have
Schedule a callDisclaimer: All third-party content on this website/platform is and will remain the property of their respective owners and is provided on "as is" basis without any warranties, express or implied. Use of third-party content does not indicate any affiliation, sponsorship with or endorsement by them. Any references to third-party content is to identify the corresponding services and shall be considered fair use under The CopyrightLaw.
