A proposed approach to estimate and reduce the environmental impact from whole farms

Major US electric utility climate pledges have the potential to collectively reduce power sector emissions by one-third

Fourteen mature technology biomass refining scenarios – involving both biological and thermochemical processing with production of fuels, power, and/or animal feed protein – are compared with respect to process efficiency, environmental impact – including petroleum use, greenhouse gas (GHG) emissions, and water use–and economic profitability. The emissions analysis does not account for carbon sinks (e.g., soil carbon sequestration) or sources (e.g., forest conversion) resulting from land‐use considerations. Sensitivity of the scenarios to fuel and electricity price, feedstock cost, and capital structure is also evaluated. The thermochemical scenario producing only power achieves a process efficiency of 49% (energy out as power as a percentage of feedstock energy in), 1359 kg CO2 equivalent avoided GHG emissions per Mg feedstock (current power mix basis) and a cost of $0.0575/kWh ($16/GJ), at a scale of 4535 dry Mg feedstock/day, 12% internal rate of return, 35% debt fraction, and 7% loan rate. Thermochemical scenarios producing fuels and power realize efficiencies between 55 and 64%, avoided GHG emissions between 1000 and 1179 kg/dry Mg, and costs between $0.36 and $0.57 per liter gasoline equivalent ($1.37 – $2.16 per gallon) at the same scale and financial structure. Scenarios involving biological production of ethanol with thermochemical production of fuels and/or power result in efficiencies ranging from 61 to 80%, avoided GHG emissions from 965 to 1,258 kg/dry Mg, and costs from $0.25 to $0.33 per liter gasoline equivalent ($0.96 to $1.24/gallon). Most of the biofuel scenarios offer comparable, if not lower, costs and much reduced GHG emissions (>90%) compared to petroleum‐derived fuels. Scenarios producing biofuels result in GHG displacements that are comparable to those dedicated to power production (e.g., >825 kg CO2 equivalent/dry Mg biomass), especially when a future power mix less dependent upon fossil fuel is assumed. Scenarios integrating biological and thermochemical processing enable waste heat from the thermochemical process to power the biological process, resulting in higher overall process efficiencies than would otherwise be realized – efficiencies on par with petroleum‐based fuels in several cases. © 2009 Society of Chemical Industry and John Wiley & Sons, Ltd

Energy-related activities are a major contributor of greenhouse gas (GHG) emissions. A growing body of knowledge clearly depicts the links between human activities and climate change. Over the last century the burning of fossil fuels such as coal and oil and other human activities has released carbon dioxide (CO2) emissions and other heat-trapping GHG emissions into the atmosphere and thus increased the concentration of atmospheric CO2 emissions. The main human activities that emit CO2 emissions are (1) the combustion of fossil fuels to generate electricity, accounting for about 37% of total U.S. CO2 emissions and 31% of total U.S. GHG emissions in 2013, (2) the combustion of fossil fuels such as gasoline and diesel to transport people and goods, accounting for about 31% of total U.S. CO2 emissions and 26% of total U.S. GHG emissions in 2013, and (3) industrial processes such as the production and consumption of minerals and chemicals, accounting for about 15% of total U.S. CO2 emissions and 12% of total ...

Current and future greenhouse gas (GHG) emissions from the management of municipal solid waste in the eThekwini Municipality – South Africa

Global economic development has highlighted the issue of climate change, which is one of the most important environmental issues plaguing human beings. It is widely agreed that excessive greenhouse gas (GHG) emissions are important factors contributing to global warming. Many countries have formulated corresponding GHG emission reduction plans to deal with climate change issues. An important GHG emission source is released from sewage-sludge treatment systems. However, there has not been a comprehensive quantitative GHG emissions evaluation system in the case of sewage-sludge treatment systems, due to multiple emission sources, complex processes, and different standards. In previous studies, the Guidelines for National Greenhouse Gas Inventories (Intergovernmental Panel on Climate Change, IPCC, 2006) and Chinese Greenhouse Gas Inventory (National Center for Climate Change Strategy and International Cooperation, NCSC, 2005) were widely applied to estimate GHG emissions from sewage-sludge treatment. However, IPCC does not consider CO2 emissions from sewage treatment, and NCSC does not consider CO2 emissions from the sewage treatment and N2O emissions from sludge treatment. Therefore, the following have been conducted in this study: (1) A GHG estimation model basing on Life Cycle Thinking (LCT) was constructed, and the research objects were CH4, N2O, and CO2 that were produced by the sewage-sludge treatment system. The estimation model of CO2 and N2O, which were ignored in the IPCC report, were analyzed and discussed. The models of the GHG emission estimation were summarized and improved in the urban sewage-sludge treatment system under the different sewage-sludge treatment process scenarios. (2) The GHG emission load of major urban sewage-sludge treatment processes was analyzed, and the level and key links of environmental impacts generated by different processes were identified. This helps to understand and compare the environmental impacts of different treatment processes and provides suggestions for the sustainable development of wastewater treatment processes. (3) The GHG emission characteristics of nine scenarios of different sewage-sludge treatment processes were analyzed, and the environmental impacts caused by energy consumption and chemicals consumption were studied. Consequently, the sewage-sludge treatment process under low carbonization and low environment impact were proposed.

Several EU countries import wood pellets from the south‐eastern United States. The imported wood pellets are (co‐)fired in power plants with the aim of reducing overall greenhouse gas (GHG) emissions from electricity and meeting EU renewable energy targets. To assess whether GHG emissions are reduced and on what timescale, we construct the GHG balance of wood‐pellet electricity. This GHG balance consists of supply chain and combustion GHG emissions, carbon sequestration during biomass growth and avoided GHG emissions through replacing fossil electricity. We investigate wood pellets from four softwood feedstock types: small roundwood, commercial thinnings, harvest residues and mill residues. Per feedstock, the GHG balance of wood‐pellet electricity is compared against those of alternative scenarios. Alternative scenarios are combinations of alternative fates of the feedstock materials, such as in‐forest decomposition, or the production of paper or wood panels like oriented strand board (OSB). Alternative scenario composition depends on feedstock type and local demand for this feedstock. Results indicate that the GHG balance of wood‐pellet electricity equals that of alternative scenarios within 0–21 years (the GHG parity time), after which wood‐pellet electricity has sustained climate benefits. Parity times increase by a maximum of 12 years when varying key variables (emissions associated with paper and panels, soil carbon increase via feedstock decomposition, wood‐pellet electricity supply chain emissions) within maximum plausible ranges. Using commercial thinnings, harvest residues or mill residues as feedstock leads to the shortest GHG parity times (0–6 years) and fastest GHG benefits from wood‐pellet electricity. We find shorter GHG parity times than previous studies, for we use a novel approach that differentiates feedstocks and considers alternative scenarios based on (combinations of) alternative feedstock fates, rather than on alternative land uses. This novel approach is relevant for bioenergy derived from low‐value feedstocks.

A comparison of avoided greenhouse gas emissions when using different kinds of wood energy

Taking Stock of Strategies on Climate Change and the Way Forward: A Strategic Climate Change Framework for Australia

BackgroundPolicies to mitigate climate change by reducing greenhouse gas (GHG) emissions can yield public health benefits by also reducing emissions of hazardous co-pollutants, such as air toxics and particulate matter. Socioeconomically disadvantaged communities are typically disproportionately exposed to air pollutants, and therefore climate policy could also potentially reduce these environmental inequities. We sought to explore potential social disparities in GHG and co-pollutant emissions under an existing carbon trading program—the dominant approach to GHG regulation in the US and globally.Methods and findingsWe examined the relationship between multiple measures of neighborhood disadvantage and the location of GHG and co-pollutant emissions from facilities regulated under California’s cap-and-trade program—the world’s fourth largest operational carbon trading program. We examined temporal patterns in annual average emissions of GHGs, particulate matter (PM2.5), nitrogen oxides, sulfur oxides, volatile organic compounds, and air toxics before (January 1, 2011–December 31, 2012) and after (January 1, 2013–December 31, 2015) the initiation of carbon trading. We found that facilities regulated under California’s cap-and-trade program are disproportionately located in economically disadvantaged neighborhoods with higher proportions of residents of color, and that the quantities of co-pollutant emissions from these facilities were correlated with GHG emissions through time. Moreover, the majority (52%) of regulated facilities reported higher annual average local (in-state) GHG emissions since the initiation of trading. Neighborhoods that experienced increases in annual average GHG and co-pollutant emissions from regulated facilities nearby after trading began had higher proportions of people of color and poor, less educated, and linguistically isolated residents, compared to neighborhoods that experienced decreases in GHGs. These study results reflect preliminary emissions and social equity patterns of the first 3 years of California’s cap-and-trade program for which data are available. Due to data limitations, this analysis did not assess the emissions and equity implications of GHG reductions from transportation-related emission sources. Future emission patterns may shift, due to changes in industrial production decisions and policy initiatives that further incentivize local GHG and co-pollutant reductions in disadvantaged communities.ConclusionsTo our knowledge, this is the first study to examine social disparities in GHG and co-pollutant emissions under an existing carbon trading program. Our results indicate that, thus far, California’s cap-and-trade program has not yielded improvements in environmental equity with respect to health-damaging co-pollutant emissions. This could change, however, as the cap on GHG emissions is gradually lowered in the future. The incorporation of additional policy and regulatory elements that incentivize more local emission reductions in disadvantaged communities could enhance the local air quality and environmental equity benefits of California’s climate change mitigation efforts.

GHG footprint of major cities in India

The production of six regionally important cellulosic biomass feedstocks, including pine, eucalyptus, unmanaged hardwoods, forest residues, switchgrass, and sweet sorghum, was analyzed using consistent life cycle methodologies and system boundaries to identify feedstocks with the lowest cost and environmental impacts. Supply chain analysis models were created for each feedstock calculating costs and supply chain requirements for the production 453,592 dry tonnes of biomass per year. Cradle-to-gate environmental impacts from these supply systems were quantified for nine mid-point indicators using SimaPro 7.2 LCA software. Conversion of grassland to managed forest for bioenergy resulted in large reductions in GHG emissions, due to carbon sequestration associated with direct land use change. However, converting forests to energy cropland resulted in large increases in GHG emissions. Production of forest-based feedstocks for biofuels resulted in lower delivered cost, lower greenhouse gas (GHG) emissions and lower overall environmental impacts than the studied agricultural feedstocks. Forest residues had the lowest environmental impact and delivered cost per dry tonne. Using forest-based biomass feedstocks instead of agricultural feedstocks would result in lower cradle-to-gate environmental impacts and delivered biomass costs for biofuel production in the southern U.S.

Better information on greenhouse gas (GHG) emissions and mitigation potential in the agricultural sector is necessary to manage these emissions and identify responses that are consistent with the food security and economic development priorities of countries. Critical activity data (what crops or livestock are managed in what way) are poor or lacking for many agricultural systems, especially in developing countries. In addition, the currently available methods for quantifying emissions and mitigation are often too expensive or complex or not sufficiently user friendly for widespread use.The purpose of this focus issue is to capture the state of the art in quantifying greenhouse gases from agricultural systems, with the goal of better understanding our current capabilities and near-term potential for improvement, with particular attention to quantification issues relevant to smallholders in developing countries. This work is timely in light of international discussions and negotiations around how agriculture should be included in efforts to reduce and adapt to climate change impacts, and considering that significant climate financing to developing countries in post-2012 agreements may be linked to their increased ability to identify and report GHG emissions (Murphy et al 2010, CCAFS 2011, FAO 2011).

BackgroundSocietal pressures exist to reduce greenhouse gas (GHG) emissions from farm animals, especially in beef cattle. Both total GHG and GHG emissions per unit of product decrease as productivity increases. Limitations of previous studies on GHG emissions are that they generally describe feed intake inadequately, assess the consequences of selection on particular traits only, or examine consequences for only part of the production chain. Here, we examine GHG emissions for the whole production chain, with the estimated cost of carbon included as an extra cost on traits in the breeding objective of the production system.MethodsWe examined an example beef production system where economic merit was measured from weaning to slaughter. The estimated cost of the carbon dioxide equivalent (CO2-e) associated with feed intake change is included in the economic values calculated for the breeding objective traits and comes in addition to the cost of the feed associated with trait change. GHG emission effects on the production system are accumulated over the breeding objective traits, and the reduction in GHG emissions is evaluated, for different carbon prices, both for the individual animal and the production system.ResultsMultiple-trait selection in beef cattle can reduce total GHG and GHG emissions per unit of product while increasing economic performance if the cost of feed in the breeding objective is high. When carbon price was $10, $20, $30 and $40/ton CO2-e, selection decreased total GHG emissions by 1.1, 1.6, 2.1 and 2.6% per generation, respectively. When the cost of feed for the breeding objective was low, selection reduced total GHG emissions only if carbon price was high (~ $80/ton CO2-e). Ignoring the costs of GHG emissions when feed cost was low substantially increased emissions (e.g. 4.4% per generation or ~ 8.8% in 10 years).ConclusionsThe ability to reduce GHG emissions in beef cattle depends on the cost of feed in the breeding objective of the production system. Multiple-trait selection will reduce emissions, while improving economic performance, if the cost of feed in the breeding objective is high. If it is low, greater growth will be favoured, leading to an increase in GHG emissions that may be undesirable.

Modelling soil organic carbon (SOC) stock changes in agroecosystems can be performed with different approaches depending on objectives and available data. Our objective in this paper is to describe a scheme for developing a dynamic SOC algorithm for calculating net greenhouse gas emissions from Canadian farms as a function of management and local conditions. Our approach is flexible and emphasizes ease of use and the integration of available knowledge. Using this approach, we assessed the performance of several SOC models having two or more compartments for some common agroecosystems in Canada. Analysis of long-term data for conventional management practices at different sites (n = 36) in Canada, including recent model applications in the literature on some of those data, indicated that the results obtained with two-compartment models, such as the Introductory Carbon Balance Model (ICBM) and Modified Woodruff Model (MWM), yielded results comparable to those of a multi-compartment model (CENTURY). The analysis also showed that a model such as ICBM need stuning to be applied to management and conditions across Canada. Two-compartment models programmable in a simple spreadsheet format, though they may not supplant more complex models in allapplications, offer advantages of simplicity and transparency in whole-farm analyses of greenhouse gas emissions. Key words: Virtual Farm, soil organic carbon, soil disturbance, C inputs, Introductory Carbon Balance Model (ICBM), CENTURY, Modified Woodruff Model (MWM).

Executive Summary: The California Climate Action Registry, which was initially established in 2000 and began operation in Fall 2002, is a voluntary registry for recording annual greenhouse gas (GHG) emissions. The purpose of the Registry is to assist California businesses and organizations in their efforts to inventory and document emissions in order to establish a baseline and to document early actions to increase energy efficiency and decrease GHG emissions. The State of California has committed to use its ''best efforts'' to ensure that entities that establish GHG emissions baselines and register their emissions will receive ''appropriate consideration under any future international, federal, or state regulatory scheme relating to greenhouse gas emissions.'' Reporting of GHG emissions involves documentation of both ''direct'' emissions from sources that are under the entity's control and indirect emissions controlled by others. Electricity generated by an off-site power source is consider ed to be an indirect GHG emission and is required to be included in the entity's report. Registry participants include businesses, non-profit organizations, municipalities, state agencies, and other entities. Participants are required to register the GHG emissions of all operations in California, and are encouraged to report nationwide. For the first three years of participation, the Registry only requires the reporting of carbon dioxide (CO2) emissions, although participants are encouraged to report the remaining five Kyoto Protocol GHGs (CH4, N2O, HFCs, PFCs, and SF6). After three years, reporting of all six Kyoto GHG emissions is required. The enabling legislation for the Registry (SB 527) requires total GHG emissions to be registered and requires reporting of ''industry-specific metrics'' once such metrics have been adopted by the Registry. The Ernest Orlando Lawrence Berkeley National Laboratory (Berkeley Lab) was asked to provide technical assistance to the California Energy Commission (Energy Commission) related to the Registry in three areas: (1) assessing the availability and usefulness of industry-specific metrics, (2) evaluating various methods for establishing baselines for calculating GHG emissions reductions related to specific actions taken by Registry participants, and (3) establishing methods for calculating electricity CO2 emission factors. The third area of research was completed in 2002 and is documented in Estimating Carbon Dioxide Emissions Factors for the California Electric Power Sector (Marnay et al., 2002). This report documents our findings related to the first areas of research. For the first area of research, the overall objective was to evaluate the metrics, such as emissions per economic unit or emissions per unit of production that can be used to report GHG emissions trends for potential Registry participants. This research began with an effort to identify methodologies, benchmarking programs, inventories, protocols, and registries that u se industry-specific metrics to track trends in energy use or GHG emissions in order to determine what types of metrics have already been developed. The next step in developing industry-specific metrics was to assess the availability of data needed to determine metric development priorities. Berkeley Lab also determined the relative importance of different potential Registry participant categories in order to asses s the availability of sectoral or industry-specific metrics and then identified industry-specific metrics in use around the world. While a plethora of metrics was identified, no one metric that adequately tracks trends in GHG emissions while maintaining confidentiality of data was identified. As a result of this review, Berkeley Lab recommends the development of a GHG intensity index as a new metric for reporting and tracking GHG emissions trends.Such an index could provide an industry-specific metric for reporting and tracking GHG emissions trends to accurately reflect year to year changes while protecting proprietary data. This GHG intensity index changes while protecting proprietary data. This GHG intensity index would provide Registry participants with a means for demonstrating improvements in their energy and GHG emissions per unit of production without divulging specific values. For the second research area, Berkeley Lab evaluated various methods used to calculate baselines for documentation of energy consumption or GHG emissions reductions, noting those that use industry-specific metrics. Accounting for actions to reduce GHGs can be done on a project-by-project basis or on an entity basis. Establishing project-related baselines for mitigation efforts has been widely discussed in the context of two of the so-called ''flexible mechanisms'' of the Kyoto Protocol to the United Nations Framework Convention on Climate Change (Kyoto Protocol) Joint Implementation (JI) and the Clean Development Mechanism (CDM).